Search Documents

By Adam Levy, Thomas Novak, Sampurna Arya, Joseph Sottile, Kozo Saito

The use of a woven wire-mesh screen as part of a flooded-bed dust-scrubbing system is very popular in the underground coal mining industry. It is used in combination with a demister (mist eliminator) to remove dust from the dust-laden air. A study was conducted to measure the pressure drop across a flooded-bed wire-mesh screen at different airflow rates in onephase (dry) and two-phase (wet) conditions. Two empirical relationships between pressure drop and air velocity were developed for dry and wet conditions, respectively. In both cases, the form of the empirical relationships was found to be similar to relationships given by Sabri Ergun for high velocity non-Darcy single and multi-phase flow through porous media. The experiments were repeated on a reduced-scale model of the wire-mesh screen, and the pressure-velocity relationships obtained from the full-scale prototype experiments were tested. The test results show validation of the full-scale empirical formulas on the small-scale model with an insignificant variation. This paper presents the empirical equations for pressure drop across the wire-mesh screen in dry and wet conditions. Researchers can use these equations as a tool to predict total pressure drops for wire-mesh screens of different scale sizes.

By W. K. Pincock

Accident prevention can be portrayed as a science that deals with facts and natural phenomena and must be dealt with in the same manner as any other operating problem. Safety at the Copper Queen Branch dates back to 1913 when a Safety Organization was started and rules formulated for underground mining. Since then the mining industry has made substantial progress in the elimination of accidents and when the Lavender Pit was started in 1951, it adopted the general plan in use at all Phelps Dodge properties. Following is a brief description of the Pit Operations:

Jan 1, 1959

By Alan Bye

Sandsloot open pit is situated on the northern limb of the Bushveld Complex, 250 km north east of Johannesburg, South Africa. Sandsloot is currently the largest open pit platinum mine in the world and is one of six potential open pits in the area. The geotechnical strength properties of the Platreef have posed significant mining and processing challenges to the PPRust operation since inception in 1992. In order to optimise the whole business as opposed to isolated cost centres a mine to mill initiative was embarked upon in 1997. Initial work focussed on ore characterisation and an entire suite of data was collected for each rock type. This included mineralogy, geochemistry, geotechnical, blastability indices as well as metallurgical strength data. The second phase involved the clear definition of customer requirements, namely the optimum performance criteria for the plant and mining departments. This involved extensive field trials and data capture to measure the interaction and influence of the mine to mill value chain. Once the design targets were defined a 3D geotechnical model was constructed to ensure that the targets were consistently achieved. The model is very similar to an ore reserve model however it is populated with geotechnical, metallurgical and blast index data. Through software queries the appropriate blast powder factor for each mining block can be obtained thereby ensuring the correct fragmentation is blasted for the plant and mining operation. The initiative has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables as well as higher plant throughput. Additionally, the initiative has benefited both Brownfield and Greenfield projects on the PPRust operation.

Jan 1, 2005

By R. K. Devala

In this paper, numerical approximation schemes, for solution of the mass transfer problem in mine ventilation have been developed by using three implicit finite difference schemes. Results from these schemes have been compared with the analytical solution for spatial and time increments, using the concept of Root Mean Square error. For implicit finite difference schemes, in general, the modified central difference scheme is better than the two other schemes at lower velocity. Also, at lower air velocities, implicit schemes underpredicted the concentration values. At higher air velocities, the Crank-Nicholson and Laasonen schemes provided better results than the Modified Central Difference scheme.

Jan 1, 1994

By Richard H. Olson

Talc deposits in the Precambrian of southwestern Montana (Beaverhead and Madison Counties) are unique within the U. S. A. in that large bodies of tremolite-free talc can be open-pit mined. All known deposits are in pre-Beltian dolomite units. The origin is suspected to be metasomatic, with the siliceous component having been contributed by an intrusive Precambrian granite gneiss. Precambrian deformation was extreme and is characterized by multiple periods of tight isoclinal folding and the flowage of less competent rocks, rather than by faulting. Post- Precambrian folding has been relatively negligible; the characteristic Laramide structure is block-faulting developed along northwest-southeast trends. The talc is thought to have been formed in Precambrian time; the high-angle block-faults probably have no significance with regard to the formation of the talc, but do tend to complicate mining operations. Tremolite-free talc ore bodies with horizontal widths of more than 200 feet, vertical depths of several hundreds of feet, and strike-lengths of as much as one-half mile are known in the Ruby Range and the Gravelly Range. Where dolomite is interbedded with tremolite-free talc in the Gravelly Range, the scale of this relationship permits the use of conventional open-pit mining methods with subsequent upgrading by hand-sorting techniques. Underground mining has been used in the past, but all current Montana talc-mining operations are on the surface. The hand-sorted ore, some of which is shipped overseas, is finely ground or micronized in roller mills and fluid-energy mills. The products are distributed both nationwide and abroad.

Jan 1, 1975

By John A. Patterson

There are certain data handling techniques used by statisticans that can help one to calculate the size of an orebody and to develop some of the relationships between size, cutoff grade, average grade, mining cost, and profit. Knowing the relationships amongst these factors can help determine the most desirable operating conditions. A statistical technique that we will use is data grouping. This allows us to work with relatively few groups instead of many samples, If we were able to segregate the ore in an orebody into grade groups, add the amounts in each group, and plot the sums as a curve, we would get something like Figure 1. A smooth curve develops when the grade classes are small enough, otherwise a "stair step? histogram results. The area under the curve, being the sum of the tonnages in all of the grade classes, is proportional to the total number of tons in the orebody. If we take the data of a distribution such as Figure 1 and add the tonnages above a specific grade we have in effect a cutoff grade

Jan 1, 1958

By Arthur F. Moss

Smallbore tunnels in urban environments often present more technical and managerial problems than major large diameter schemes carried out for transportion, water supply and hydro-electric facilities. The 1.8 km Bath scheme was designed for construction in tunnel using the pipe jacking system. Unforeseen ground conditions meant other techniques were needed during construction. The paper describes the problems encountered and how they were overcome.

Jan 1, 1981

By Werner A. Dürrfeld

The Bullflex® System was introduced as a substitute for timber and debris lagging in mines and to create an in-situ early-stage interlocking effect between steel supports and the rock wall. As deplacement and/or disintegration of strata and of rock beds is to be avoided under all circumstances - following the ideas of NATM-steel support can only be loaded to the maximum when point load is avoided and ideal bedding of the rock is maintained.

Jan 1, 1981

By L. G. Austin, R. S. C. Rogers

INTRODUCTION Coal is geologically a sedimentary rock with distinct bedding planes containing a mixture of petrographic constituents. Yet. because of its chemical nature, it also has some of the characteristics of a polymeric material. In addition, it is extensively precracked to give a macropore structure and also has a substantial internal volume of microporosity. Add to this the mineral constituents dispersed in the coal in a variety of forms and sizes. and it can be readily appreciated that coal is a complex and heterogeneous material. It has to date not been possible to predict the particle size distributions produced by breakage of coals from a priori application of the principles of fracture mechanics. However, there is a substantial body of data resulting from empirical observation of size distributions produced under various conditions, primarily from grinding mills. It is the function of this review to outline how this empirical information can be used to predict product size distributions for those systems which have been studied systematically, and to suggest future avenues of research using similar methodology. FRACTURE THEORY APPLIED TO COAL It is, of course, possible to devise experiments for slow crack propagation in a coal. However, the evidence is that coal breaks by brittle fracture in the mills and mining machines of industrial importance and therefore the theory of brittle fracture is sufficient to illustrate the important features of the fracture of coal. In order to produce size reduction a solid must be stressed by the application of force. The force can be a tensile (stretching), compressive, or shear force, and the three dimensional stress pattern in the solid represents the tensile, compressive, and shear forces per unit area acting in any direction through any point in the solid. As an illustration consider the case of a simple one-dimensional tensile stress: then stress is defined as a=F/A where F is the force. A is the cross-sectional area of the solid normal to F and strain. E, is defined as the fractional change in the length of the solid. so that E= x/L where x is the extension of an original length of L. Coal behaves as an elastic material over short times (although viscoelastic creep can occur if the stress is maintained over long times) and if it is not stretched too far the coal returns to its original shape when the stress is removed; otherwise catastrophic failure occurs and the coal fractures at a stress termed the tensile strength. The failure under stress of an elastic material is termed brittle fracture. Elastic material fails at small stain and the stress-stain relation to where brittle fracture occurs is the empirical Hooke's law. a= YE, where Y is Young's modulus. The work done on the solid to take the solid from zero external stress to a stressed state by slowly increasing F up to a final stress u is the integral of the stress times the strain. This reversible strain energy is stored in the solid and. using Hooke's law. is u /2Y per unit volume of solid. If the solid is immediately loaded to u the work done is [EAuL] which Is a2 /Y per unit volume, that is, twice the reversible work.

Jan 1, 1988

By W. K. Utt, C. C. Woodward, W. L. Howie, G. G. Miller

The process of roof drilling and bolting is one of the most dangerous jobs in underground mining. In the United States, roof drilling and bolting results in about 1,000 accidents with injuries each year. Researchers, from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are studying the feasibility of using a drill-monitoring system to estimate the strength of successive layers of rock and assess the integrity of a mine roof. Such a system would allow roof drill operators to be warned when a weak layer is being drilled. Using measurements taken during drilling, a neural network can classify mine roof strata in terms of relative strength. The concept has been proven in principle. This research project was undertaken to increase the safety of underground miners, especially those involved in roof bolting. The system should be applicable to the mobile drills now used in underground mines, and the system would likely find wider application as well.

Jan 1, 2003

By Gh. Crutu

The handling of radioactive waste deposits from factories that produce chemical fertilizers is a difficult problem, but has a great significance for soil quality and for the environment. The Romanian legislation has produced law and normative acts concordant with EU regulations for prevention and protection, and also for environmental contamination control with radionuclides. The soils and agricultural plants in the vicinity of phosphogypsum deposits are radioactively contaminated; the annual variability of the respective radioactivity values is demonstrated by annual records. Residual radioactivity monitoring determines the presence of radioactive ions in the soil and cultivated plants: wheat, maize, sunflower, as well as the spontaneous flora. The results obtained lead to the conclusion that ecological restoration works must be executed for degraded soils due to impacts of radioactive materials.

Jan 1, 2007

By James A. Holtkamp

Environmental regulation in Mexico has matured dramatically and effectively in the last decade. The gap between environmental regulation in the United States and Mexico is rapidly narrowing. From a regulatory perspective, it is no longer necessarily less burdensome to operate in Mexico. Principal laws and regulations Mexico has two principal environmental regulatory systems. The first consists of the laws and regulations governing domestic activities. The second consists of the treaties, agreements and understandings between the United States and Mexico dealing with transboundary pollution and maquiladoras (see Maquiladora Decree, next column). The following are the principal major laws and regulations governing environmental protection in Mexico: General Law: The General Law on Ecological Balance and Protection of the Environment, effective March 1, 1988. Water Regulations: Regulations for the Prevention and Control of Water Pollution, effective May 29, 1973. Environmental Impact Regulations: Regulations of the General Law on Ecological Balance and Protection of the Environment, regarding Environmental Impact, effective June 8, 1988.

Jan 1, 1994

By Joyce A. Ober

Strontium occurs commonly in nature, averaging 0.034% of all igneous rock; however, only two minerals, celestite and strontianite, contain strontium in sufficient quantities to make its recovery practical, and these minerals are found in sedimentary rocks. Of the two, only celestite has been found to occur in deposits of sufficient size to make development of mining facilities currently attractive. Celestite, the most common strontium mineral, consists primarily of strontium sulfate (SrSO,). Strontianite, the second most common mineral, consists primarily of strontium carbonate (Sr CO3). Strontianite would be the more useful of the two common minerals because strontium is used most commonly in the carbonate form, but few deposits have been discovered that are suitable for development. The physical properties of strontium ores are listed in [Table 1].

Jan 1, 1994

By R. A. Metz, Michael M. Easdon, Michael J. Fiannaca

Disseminated epithermal gold metallization occurs within a breccia unit interpreted to be a submarine debris flow. Gold is associated with oxidized pyrite, fluorite, and jasperoidal silica. A minimum of 8 Mt (9 million at) of open-pittable mining reserves will be cyanide heap leached as run-of-mine ore at a rate of 0.9 Mt (1.0 million stpy). Careful evaluation of the combined results of successive sampling projects has established the pit plan, minable reserves, and process metallurgy of the operation. The sampling procedure utilized for a given test depended upon geological interpretation as well as the procedures, successes, and failures of previous tests. This paper summarizes the sampling and testing procedures of the development effort in light of the project goals and attendant problems in achieving them.

Jan 1, 1992

By Edward K. E. ] [Williams

Conditioning is any treatment of an ore with or without reagents which affect its floatability. While it can start in crushing or grinding circuits and continue into the flotation circuit, conditioning will refer here only to reagent treatment in an agitated tank designed for the purpose. Such treatment is often unnecessary with sulphide ores and collectors or with amines,* but it has long been recognized as essential with fatty acid collectors in the flotation of non-sulphide minerals, The requirements can be extremely variable, depending upon ore alteration, the presence or absence of slimes, and 1 the minerals to be separated. The study described here was concerned with the recovery of oxidized molybdenum minerals from an ore containing the element in both sulphide and oxidized form. Flotation of the iron minerals with which the oxidized molybdenum was associated was the basis for the process. Recovery and optimum concentrate grade without desliming depended upon a twenty to thirty minute conditioning of the pulp with flotation reagents at forty to fifty percent solids and at high turbulence. The objective in the study was the determination of design and operating criteria for conditioners in order to permit scaling-up of the results without repeating the entire study on a larger scale.

Jan 1, 1968

By Brendan Parker, Joseph Skrypniuk

Boddington Gold Mine1 (BGM) commenced production in 1987 and is currently ranked as the second largest gold producer in Australia. In a strategy to improve plant efficiency, constraints to plant performance were identified and prioritised with a view to maximising benefit for minimal expenditure. After identifying that leach kinetics and circuit residence time were major constraints, the introduction of oxygen was identified as having the greatest potential for the delivery of sig­nificant cost benefits. The application of oxygen, initially by conventional tech­niques, and subsequently by installation of Atomaer's Filblast gas shear reactor, improved gold recovery, reduced the resi­dence time constraint and enabled higher mill throughput to be achieved. Additional benefits included operation at lower pulp densities and a reduction in reagent usage. A significant reduc­tion in unit operating cost resulted from these benefits. This paper quantifies the above benefits in a format accept­able to both metallurgists and accountants by integrating the findings in a techno-economic perspective.

Jan 1, 1996

By Johann Engelbrecht, Stéfan de Bruyn, Petrus van den Heever

A system for the on-stream X-ray diffractometric determination of mineral phases in slurries was developed in response to the mining industry's need for process control during the beneficiation of industrial minerals. The instrumentation for and results from testwork conducted at a phosphate rock beneficiation plant in Florida are discussed. Results show that the concentrations of the minerals apatite (var. francolite) and quartz can be accurately determined every few minutes, so that adjustments to the flotation circuit can be timeously executed from the control room. The on-stream measurements can ultimately be integrated into an automated plant control strategy. Estimates of savings on reagent and staffing costs, as well as the benefits from consistent grades and greater recoveries, have shown that the investment in such a system could often be recovered in less than a year.

Jan 1, 1999

By Walter N. Campbell

The Simon Silver Mine is located near Mina, Nevada, approximately 50 miles northwest of Tonopah and 40 miles east of Hawthorne. It is an old property which was last worked in 1932 and closed operations due to problems arising from low metal prices. Federal Resources Corp. acquired the property in 1963 and undertook a completely new development program since the old surface plant and underground workings were beyond feasible repair. The deposit of silver, lead, zinc and copper is predominantly replacement of limestone. In the summer of 1964, a new surface plant was constructed and on December 2, 1964, sinking of a three compartment vertical shaft started and was completed to a depth of 1088 feet in April of 1965. Following the sinking program an 850 foot crosscut was driven to intersect the mineral zone on the 1000 level after which drifting, crosscutting and raising totaling some additional 4280 feet has been completed along with considerable diamond drilling and long holing into the walls. To date, two ore bodies have been encountered and test stoping operations are underway together with development of the 800 level for servicing, ventilation and access. The present development of ore is directed towards substantiating sufficient reserves to warrant the construction of a flotation mill.

Jan 1, 1967

By D. S. Choi

Underground production of coal by longwall methods has increased significantly in the last few years and will very likely continue to: increase. There are several reasons for this. First, as mining moves into seams having greater overburden, roof exposure must be reduced since support will become' increasingly expensive. Secondly, the growing demand for coal has forced the coal industry to seek alternative, more productive, coal mining methods. In addition, the longwall method greatly simplifies the underground ventilation network. This paper addresses itself to the design of longwall development headings, particularly to those of the United States where multiple development headings are required by law. The most burdensome problem encountered in many longwall mining installations is deterioration of the tailgate due to the combined effect from, the active longwall gob and the old gob made by mining the previous panel.1 Portions of the tailgate entry are sometimes closed to such a degree that extensive repair work is necessary to keep the entry in usable condition. The purpose of this paper is to present the result of a study in progress which combines field measurements with numerical model analysis to reduce the cost of maintaining tailgate entries in longwall mining systems.

Jan 1, 1975

By David M. Mchaina, Michel Grenier, Stephen G. Hardcastle

An airborne dust survey was conducted at the Arthur W. White mine of Dickenson Mines Limited by CANMET/MRL and Dickenson Mines Limited Staff in April 1990 for the purpose of evaluating environmental conditions underground and in the surface mining plants. The survey was designed to measure respirable silica, total arsenic and lead concentrations at several workplaces. In addition, settled dust and rock samples were collected from workplaces and analysed for total arsenic content. More importantly, arsenic exposure data were needed to evaluate the impact of Ontario Regulation 176/86 as amended by Ontario Regulation 23/87. A total of 165 area and personal air filter samples were collected during the study. Of these, 85, 67 and 13 samples were for arsenic, silica and lead respectively. Sampling aid analyses were performed according to the Ontario Ministry of Labour Regulations. More than 90% of the workplaces sampled for respirable silica, total arsenic and lead were below the Ontario Ministry of Labour Regulations; and 10% of the workplaces sampled for arsenic shaved concentrations above the Threshold Limit value (TLV) proposed in the Ontario Regulation 176/86 as amended by Ontario Regulation 23/87. These results were used to identify occupations and/or workplaces where more sampling and control measures were required respirable silica, total arsenic and lead. This paper describes the results of the dust sampling program conducted at Dickenson Mines Limited.

Jan 1, 1991