Search Documents

By Stephen Krickovic

"Bleeding", as used in mine ventilation language, has a number of meanings among mining men and is regarded with different degrees of importance. This lack of uniformity stems from a number of specific situations. A method that is adequate in a mildly gaseous mine may fall short in a very gaseous mine. Projected bleeders could be dependable under a certain type of roof, and totally unsatisfactory under a different type. Similarly a plan of bleeders can be rendered useless due to undulations of seam and water in one mine and function well in another. Finally, what is effective in a mining system with partial recovery will not suffice with full recovery. You may wonder, then, if there is a common denominator for the essential function of "bleeding". In my opinion, there is, and it can be defined as controlled movement of air across an active pillar line toward the back and outby ends of the adjacent gob area into the headings provided for the purpose. The objective is to maintain as methane-free as practicable a belt adjacent to the working places, so that, if face ventilation is interrupted temporarily, the gas will not accumulate in dangerous volumes at the working faces before ventilation is restored. It's possible for these temporary interruptions to be unnoticed in time or at all. In such cases, ineffective bleeding could cause a disaster. This has happened. To control, there must be power. That is to say, there must be adequate air, pressure differential between the front and back ends of a pillar line to facilitate proper regulation for diverting of air to the various portions of the gob and as far away from the active section as is practicable. As an indication of the importance of pressure, it is noteworthy that one may provide and maintain in a reasonably open condition a heading or two for a bleeder system and fail to obtain effective bleeding .because air pressure differential is inadequate. On the other hand, you are all familiar with the fact that pillar lines in some seams can be ventilated adequately by air flow straight across the gob when the section is near a main return shaft and thus obtains a heavy pressure differential.

Jan 1, 1962

By Philip E. LaMoreaux

The development of large quantities of ground water for any major use in an area is always of environmental concern to representatives of regulatory groups, citizens, agricultural and industrial users. From these concerns, state and federal congressional representatives receive a variety of impulses from their constituents and in turn begin a series of questions upon which to-base appropriate legislative actions. The kaolin industry in Georgia is substantial to the economy and the welfare of an important segment of east-central Georgia. It uses large quantities of water for processing. This constitutes an important source of income and tax revenue. Pumping test procedures to provide an accurate and efficient dewatering scheme have been developed and carried out at a number of mines in the kaolin district of Georgia. This paper highlights one such test and is directed at an assessment of the impact of this industry on ground water supplies of an area.

Jan 1, 1983

By P. A. K. Wilkinson

This paper is concerned with the development of an in situ recovery of boric acid from a deep-seated colemanite deposit in California. The deposit contains 147 million tons of borate ore containing 6.4% boron oxide (B203). It is the largest undeveloped colemanite deposit in the United States and because of its unique occurrence and grade, in situ extraction appears to be the most economic viable process. The paper covers the geological, mineralogical, hydrological, well-field development, and extraction considerations leading to the initial pilot plant and subsequent demonstration plant phases of the project. Market potential aspects and preliminary economics of the project are also covered.

Jan 1, 1987

By K. L. Wiley

In-situ leaching, initiated in 1986 at San manual, was economically developed in 1989. The primary reason for this lag time between startup and viable production was the time required for technical development. The technical development pursued comprised detailed design, development, and implementation of in-situ well construction methods, formulation of suitable well pattern arrays, and the development of extensive hydrogeologic and geochemical knowledge of the mineral deposit. Since 1989, the in-situ leaching program has become a viable and cost effective method to extract copper from the supergene mineralized zone of the San Manuel deposit. The in-situ leaching methods that are currently utilized have been progressively expanded and continually developed and will became the cornerstone of copper production from the San Manuel oxide mineral deposit. This paper presents an overview of the supergene hydrogeology, current design techniques, drilling methods and well completion, pump determination and setting, solution management, and future plans for the increased extraction of copper by in-situ leaching methods at the San Manuel mine.

Jan 1, 1993

By Dennis F. Koschak

Production tests at Reserve Mining Company's iron ore pelletizing plant established that rubber-lined balling dm produce a green pellet equivalent in quality to those produced in conventional balling drums equipped with reciprocating cutter bars. The flexing action of the rubber liner prevents concentrate buildup in the drums, eliminating the need for a cutter bar. Advantages of the rubber-lined drum includes a reduction in maintenance and operating manpower, reduced bentonite consumption with less drum surging, reduced power consumption, and improved drum on time.

Jan 1, 1983

By Charles A. Hickey

The dining industry game tome Spruce Pine area a few years after tine Civil War. Two Yankees came down from Massachusetts to mine sheet mica to sell to the stove manufacturers for windows in heating stoves. At this time the method of mining was very crude; it was done only with pick and shovel. They were mining mica from the soft veins. Later they progressed to hand grilling and blasting. Hand drilling was quite an art in the area. One man would hold and turn the steel while one or two other men would drive the steel with hammers. In shaft raining, the muck and water was removed by hand winches called windlasses. About 1920 air compressors and jack hammers came into use. These were perhaps tide greatest improvement that has ever come to the area's mining industry. Later carne gasoline hoists, air drive water pumps, and all electrical equipment. Mica mining has, for the past few years, been very modern and efficient.

Jan 1, 1962

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp., and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the seconaary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1981

By William E. Robinson

Our earthly treasures are being quickly depleted. We have experienced what can happen in an energy crisis. You have read and heard all kinds of stories as to what caused this crisis. On the surface it would seem that all of a sudden a situation becomes a crisis whether it be fuel, potatoes, beef or whatever. Well, of course, they don't just happen. There is always a little fore-warning here, an indicator there. Someone recognizes a sign of potential trouble but is ridiculed when he forecasts it. We are running out of sand: Producers of aggregates who can say today ... "That couldn't happen to me", can well be awakened tomorrow to the cold fact of reality. It could come from any number of directions. Depletion is mostly foreseeable but zoning isn't. Legislation can also be sudden death to availibility. With the ever growing population moving into the rural countryside, available deposits are being sold either to developers or being zoned for restricted use. The fact that a gravel pit or quarry is located on a particular plot has not fazed some of the local planning boards when they decided to place the adjoining property in a residential Zone A. Proponents of zoning preach that such use is necessary to insure that the land will be put to its best use. Planning boards establish the best places for schools, homes, shopping areas, factories, etc., so that the individuals or groups are in harmony with each other. This is usually done to date without thought or consideration to the geological importance or potential of the area. Today over half of the United States is living under some form of land use restriction. Little consideration has been given to what lies under the ground to be zoned. Fortunately, the states are slowly getting around to geological surveying. I feel that it is about time that state and federal authorities institute governmental restrictions to prohibit or control local zoning ordinances which would deplete or deny an area of its natural resources. While I could continue for the balance of my time just on this facet of our industry's problems, my point is: How sure are you of your next load of sand? I could be well laughed at by some of you for saying that there is an alarmingly rapid disappearance of "nearby" sand and gravel reserves in many areas of the country. A questionable statement, except to those producers where depletion has already taken place.

Jan 1, 1974

By D. O. Murchu

Outokumpu Tara Mines located near Dublin, Ireland is Europe's largest producer of lead and zinc concentrates. To reduce dewatering costs and to improve environmental and working conditions, elimination of the lead concentrate thermal dryer was required. This paper describes the development and implementation of the pressure ceramic technology at Tara to replace a conventional vacuum filter/oil-fired dryer system. In 1996 the pressure ceramic filter dewatered 66,600tonnes of lead concentrate, producing a cake at 6 % moisture. Substantial operating cost savings have been realized. Commissioning of a second pressure ceramic filter to handle over 300,000 tonnes/year of zinc concentrates is scheduled for the first quarter of 1997.

Jan 1, 1997

By Rodolfo V. de la Cruz

The broad front concept is based on the principle that gasification can be achieved more efficiently and completely from a plane broad combustion front in contrast to other geometries obtainable with current methods of gasification. By restricting combustion to a plane broad front, the ideal condition for gasification is achieved. A plane broad combustion front can be developed in coal by initiating and propagating combustion from the walls of an oriented channel and collecting product gases from another similarly oriented channel. Flow will then be directed along the highest permeability of the coal bed, the available cross-sectional area for fluid flow is substantially increased and, more importantly, the increased flow will be uniformly distributed throughout the whole mass of coal. The success of the method is greatly dependent on how well an initial and rigorous permeability survey and associated corrective measures yield a well-characterized coal bed. To maintain uniform reaction rates, the advance of the combustion front is located with pressure- or mass flow-transducers. These sensors are then connected to servo-controlled mufflers for controlling segments of the fire front which are advancing ahead of others. Finally, the development of the concept to overcome problems of roof collapse, reactant and product gas leakages, and water invasion are briefly summarized.

Jan 1, 1976

By Warren N. Warhol

The mutual growth of the rare earth industry and the Mountain Pass Operations was no coincidence. It was the commercial availability of rare earths on a scale first made possible by the capacity of the Mountain Pass Operations that spurred research and development efforts toward new applications for rare earths. The first important demand on Mountain Pass was europium oxide for the activation of red phosphor for color television tubes in 1964. Since that time, other rare earths have become even more important, and Molycorp is continuing to supply an ever widening variety of rare earth concentrates and compounds. We enjoy saying that rare earths are not really rare, and that they are not earths, either. Of course, we are talking about the 15 metallic elements with atomic numbers 57-71, called the lanthanides, which occur in nature always together in very similar proportions. Their scarcity can be gauged by the fact that there is more cerium in the earth's crust than there is tin, and more europium than cadmium. The word "earths" comes from the early chemical term for oxide. The rare earths were discovered as oxides, and the term has persisted.

Jan 1, 1980

Large variations of coal seam thickness and roof conditions are associated with the occurrence of mine floor undulation at Shoal Creek Mine, operated by Drummond Company, Inc.. Ground control problems, such as roof falls and face failures along with extremely high shield pressure and rapid face convergence, are often reported at the longwall face when these undulations exist. This greatly increases equipment downtime and causes production delays. As a result. a comprehensive study of mine geology including roof conditions and longwall performance were conducted in the mine. With the help of continuous full-face shield pressure monitoring using the Longwall Strata Control and Maintenance System (LoSCoMS), a large data base of shield pressure with various roof conditions has been established. This enables the mine operators to accurately evaluate the roof behavior and shield performance and to take the appropriate operational steps at the face to reduce the number of downtime and face failures. This paper summarizes all works and findings from the study including detailed roof geology and its effect on longwall performance.

Jan 1, 1998

The effect of addition of a flotation collector (dodecylammonium chloride) on grinding of quartz has been studied. The data obtained are correlated with the results of tests conducted under similar chemical conditions to study influence of these additives on relevant basic sub-processes (primary breakage, pulp fluidity, and dispersion and flocculation of ground products). Such correlations suggest that the role of chemical additives in grinding is determined by their cumulative influence on the above mentioned basic properties of the system.

Jan 1, 1982

By K. Papke

Nine western states contain significant barite deposits, but most deposits are in Nevada, which has been the principal western producer for more than three decades. Nevada produces about 85% of the total United States production, but about one-half of the barite consumed in the country is imported. Approximately 95% of the barite is used in drilling muds. Sharply decreased oil and gas drilling, starting in early 1982, severely depressed the domestic barite industry. Other problems for western barite include long distances to the areas of major drilling, high railroad-freight rates, and increased barite imports. Bedded deposits, formed by submarine exhalative processes, account for almost all western production, and reserves are large.

Jan 1, 1983

By Dion Weatherley, Raúl Castro, Pablo Cid, René Gómez

In underground mining, hang-ups due to coarse fragmentation are frequently observed in drawpoints, drawbells, and ore passes during ore draw. Hang-ups can often require operational interference and hang-up removal activities. Drawpoint and drawbell design has been shown in some studies to influence hang-ups; however, the full extent of this influence remains open to question. In this study, the discrete element method was used to analyze the effect of hang-ups on three distinct drawbell geometries: the Drawer type, Circular type, and El Teniente type. The drawer type was used as the base case given that data was available from a physical model in which hang-ups were studied. The drawer type base case data was then used to calibrate our numerical model. Results show that the El Teniente drawbell geometry sustained 13% more hang-up events as compared with the base case, while the circular drawbell geometry had 16% fewer hang-up events than the base case. From this study, it can be concluded that fewer hang-up events will occur with a rounded drawbell geometry.

Apr 11, 2023

By Keros Cartwright

Distribution of temperature within the lithosphere can be significantly affected by the movement of ground water. Stallman (1960) presented the basic equation for the simultaneous transfer of heat and fluid in a porous medium and first used earth temperatures to determine aquifer permeability. Subsequently, studies of rock and soil temperatures were used to determine the flow of water through clay layers separating aquifers (Bredehoeft and Papadopulos, 1965; and Sorey, 1971), and to locate shallow aquifers (Cartwright, 1968; Birman, 1969). Cartwright (1968) showed that shallow aquifers maintain a nearly constant temperature throughout the year and that heat is exchanged between the aquifer and land surface. These temperature data also suggest that shallow aquifers hydrologically connected to surface-water systems have significantly greater effect on temperature distribution than aquifers in the deep artesian basins. Water wells developed in the shallow glacial and dolomite aquifers to depths of over 122 meters (400 feet) in northern and central Illinois produce water at temperatures very close to the mean annual air temperature. An analysis of the character of the rocks and soils suggests that the tem¬perature gradient should, and does, vary according to changes in thermal conductivity due to changes in lithology. This is because, under conditions of steady and uniform flow of heat from the earth's interior to the surface, a greater temperature gradient is required in poorly conductive rocks than in highly conductive rocks to transmit the same quantity of heat. Based on estimated values of thermal conduc-

Jan 1, 1972

By D. W. Fuerstenau

One of the more energy-efficient methods for size reduction, namely particle-bed comminution under high compressive loads, was employed to grind eight minerals and ores, using up to 250 MPa pressure. A new approach based on the self-preserving character of the ground product size distributions and a linear energy-reduction ratio relationship is proposed for analyzing this mode of size reduction. The grind ability of the material when comminuted in a particle bed is about one-half that of the single-particle crushing mode, which is in agreement with previous estimates of the relative efficiencies of energy utilization based on direct measurements of surface area produced. The loss of efficiency may be attributed to energy dissipation by particle interaction phenomena in compressed beds.

Jan 1, 1993

By M. R. Paterson

Operational and economic factors tend to favor the application of continuous processes in preference to batch processes in the majority of mineral processing applications. In this paper, the requirement for a Continuous Elution Process is established and the development of a large-scale pilot plant is described. It is based on a Continuous Elution apparatus which has a number of special features. These are the subject of various patent applications. The apparatus is suitable for adaptation to the AARL, Zadra and other methods of elution. The performance of the Atmospheric Continuous Elution System (ACE) is concluded to have significant advantages over the batch process.

Jan 1, 1986

By W. D. Presley, T. R. Harrell

This paper will be a case history of the shaft and tunnel concrete lining techniques used at the Rocky Mountain Pumped Storage Project located in northwest Georgia. Emphasis will be placed on the shaft lining techniques with only a brief description of the tunnel concrete lining techniques. The 10.67 meter (35 foot) diameter shaft and tunnel concrete linings are 0.61 meter (2 foot) nominal thickness with a single row of reinforcing bars. The tunnel was placed in 18.29 meter (60 foot) lengths with bulkheaded end sections. The 172.72 meter (566.68 foot) vertical shaft was placed in 3.05 meter (10 foot) high sections using jump forming techniques.

Jan 1, 1985

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp,, and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the secondary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1982