Search Documents

A new separator, known as the HydroFloat cell, was developed to overcome the limitations of traditional flotation cells in recovering coarse particles. The HydroFloat cell separates particles based on differences in mass after the selective attachment of air bubbles to the hydrophobic component of the feed stream. Proof-of-concept testing, utilizing phosphate matrix, heavy mineral sands and anthracite slag, indicated that significant improvements in separation efficiency can be achieved using this air-assisted teeter-bed system. Based on the encouraging laboratory results, a pilot-scale HydroFloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the +35-mesh plant feed can be increased by snore than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the +16-mesh particles in the HydroFloat concentrate. This article describes the theoretical basis for the development of the HydroFloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 2002

By M. Rosenshine, R. W. Barbaro

This paper presents a cyclic queueing model that evaluates the productivity of a shovel-truck materials haulage system. For a cyclic queueing problem with exponentially distributed service times, a cyclic queueing model provides exact solutions in a fraction of the time that simulation takes to produce an approximate solution. The model is applied to an example problem, and the results are validated with simulation. Simulation is used to show that the assumption of exponentially distributed service times and steady state are not serious problems. A cyclic queueing model can be used to quickly obtain an accurate assessment of the productivity of a shovel-truck system.

Jan 1, 1988

By Song Jiang, Xianzhi Tan, Minjie Lian

"The ground water heat pump system lades underground hot water which can be heated or cooled by heat exchanger in water source heat pump air conditioner. This system replaces the model of heating of air-conditioning by refrigerator and boiler. In this paper, the formation conditions of hot water energy in Shan Dong are analyzed in order to achieve the purpose of energy conservation and emissions reduction by taking full advantage of water resources such as water pouring and return water of beatification during the productive process of underground metal mine. In order to analyze the issue better, the paper points out some ways and methods for geothermal water often used in underground metal mine. This paper also presents the advantages of the technology of water source heat pump that is applied into underground metal mine. Here is a case study of comprehensive utilization of water source in a certain underground metal mine in Ji Ning. This mine, according to its own actual situation, designs heat pump heat exchange system which is used for indoor heating of buildings and bath for staff. It turns out that the system can save 23% water per year, cut down 3.303 million KW electric energy, and reduce 4160t emission of carbon dioxide. It is concluded that the technology of water source heat pump has broad application prospects in underground metal mine. Therefore, the results show that it is an ideal way to change the present structure of cooling and heating source in metal mine.Introduction In recent years, overuse of fossil fuels has posed a grave threat onto the environment, which makes renewable energy a more important status in energy structure. Development and utilization of renewable energy has become an important direction. Water source heat pump technology is to use solar energy stored in water as cold/heat source to convert energy. Currently, this technology has been widely used in some advanced countries. However, due to facers of implementation technology and component costs, there is still a gap in water source heat pump technology between China and these advanced countries. According to (Blum et al 2011) that after in-depth study, water source heat pump technology has developed rapidly in China recently, and the gap is gradually reduced. Groundwater source heat pump system as a kind of high efficiency, energy-saving and environmentally friendly technology in recent years, more and more get the people's attention. At the same time, its practical application has also been rapid development. Based on (Ni et al 2015) that According to the relevant departments of the prediction, the technology will become the 21st century the most efficient heating and cooling technology."

Jan 1, 2017

By John S. F. Dunlop

One of the more difficult problems frequently facing geologists and mining engineers is that of estimating the ore reserves of mineral deposits. Cost conscious mining operations invariably require an accurate knowledge of tonnage and grade for both short and long term planning. A case study is presented, showing how a classical frequency distribution was fitted to a population of drillhole assays. Using these results, a grade- tonnage curve is derived using the Lasky expressions, and the results discussed. A geostatistical analysis is then presented. First, variograms are drawn, models fitted to them and analyses made of drift and anisotropy. Second, simple block kriging is carried out and the results plotted on large 1000 scale plans, suitable for overlay with routine .mine plans. Kriging results are verified using two independent techniques: random kriging on a regular grid and inverse distance weighting. Finally an attempt is made to optimize the drilling grid, and to fully tabulate the total computer running costs for the work described.

Jan 1, 1979

By D. C. Wilder

Deformations during heating and cooling of three drifts in granitic rock were influenced by the presence of faults and shear zones. Thermal deformations were significantly larger in sheared and faulted zones than where the rock was jointed. but neither sheared nor faulted. Furthermore. thermal deformations in faulted or sheared rock were not significantly recovered during subsequent cooling thus a permament deformation remained. This inelastic response is in contrast with elastic behavior identified in unfaulted and unsheared rock segments. A companion paper (Butkovich and Patrick, 1986a) indicates that deformations in un- sheared or unfaulted rock were effectively modeled as an elastic response. We conclude that permanent deformations occurred in fractures with crushed minerals and fracture filling or gouge materials. Potential mechanisms for this permanent deformation are asperity re-adjustments during thermal deformations. micro-shearing, asperity crushing and crushing of the secondary fracture filling minerals. Additionally, modulus differences in sheared or faulted rock as compared to more intact rock would result in greater deformations in response to the same thermal loads.

Jan 1, 1986

The objective of this study is to classify ore and waste in a selected mine. The support vector machine, was used for the classification purpose, is applied to a zinc ore body in a skarn deposit located in the central region of the Peruvian Andes. The input parameters used for the model are spatial coordinates and the lithological information of the ore body. The input data was divided into training and testing data sets and the performance of the model was tested using the testing data set. The results show that more than 76% of the data could be properly classified by this method. The ore waste maps of the deposit was then developed using SVM model. From the result it was observed that a comparatively very few number of cells classified as ore. The ore is concentrated in small lodes at the middle of the volume of study, and not uniformly distributed throughout the study area. The lithological map of the deposit was also constructed as it was used as an input parameter for the SVM model. The indicator kriging was used for generation of lithological map of the ore body. Key word: Ore waste classification, Support vector machine, Indicator kriging, Confusion matrix.

Jan 1, 2008

By F. F. Aplan, V. Choudhry

This investigation is an exploratory study to evaluate a large number of potential pyrite depressants for use during coal flotation. Subsequently, the more promising reagents can be evaluated in detail. Several reagent categories (such as alkalis, lime, oxidizing agents, reducing agents, specific inorganic ions and dispersants) that were found to be effective pyrite depressants are discussed here. Other pyrite depressants will be discussed in Parts II and III.

Jan 1, 1993

By Hiroyuki Kawata, Toshiyuki Ueno, Mikio Yamazaki

INTRODUCTION For the construction of several kinds of structures which pass through under railways, we have recently developed an effective and new tunnel construction method, aiming at more secure train operation during the construction as well as the rationalization in the construction works for such structures. Most important in carrying out the construction works for the structures under railways is how to maintain the safe operation of trains. For such construction works, temporary supporting structures and supplemental works have been often applied, for which high cost and long period for the construction have been required. While, this new tunnel construction method has the feature that it is capable of constructing definitive structures for various purposes, which, at the same time, acts as the temporary supporting members for protection of railways. Therefore, this method is now drawing much attention in that higher safety of train operation, low construction cost, and shorter construction period are accomplished, minimizing the period required for slackening the train speed during the construction works.

Jan 1, 1979

By Alexander B. Ikonnikov

All known bauxite deposits in China occur in its eastern half, and almost all of them are found in the Carboniferous and the Permian. They are of platform origin, but contain diaspore as the major ore mineral. There is only one known deposit composed of gibbsite. The most valuable deposits are sedimentary ones formed in local depressions on the edges of platforms during marine transgressions. They lie on Upper Cambrian or Middle Ordovician limestone that was weathered for a long period of geological time. Generally, Chinese bauxites are low in iron, and have a rather low alumina/silica ratio.

Jan 1, 1984

By B. Cavender

Investments in new technology are often intended to improve the production or cost performance of existing operations. The economics used to justify these projects can be flawed, however, if they do not adequately consider the potential benefits of the alternative: the fully optimized use of the facility's present equipment and personnel. While new technology can be effective, dramatic improvements in production performance can also be achieved through the rigorous application of standard industrial engineering and operations management practices. An intermediate approach may also be effective: many basic improvements in the mine or plant necessary to support new technology will be equally effective when implemented for the facility's present operators. Firms that optimize their present operations are able to save the capital and avoid the risk associated with new technology. These firms will also be able to capitalize more quickly on new technology when it is implemented.

Jan 1, 2000

By M. Josick Comarmond, John J. Jeffery, John W. Bennett

Oxidation rates of sulfidic mine wastes measured at a range of size scales have been collected from a number of sources. The results suggest that well-designed laboratory columns, under controlled conditions, provide comparable information on oxidation rates to that obtained from field test piles. It has been found in the cases presented that laboratory measurements of oxidation rates of a particular material type can be applied with confidence to the same materials in the field. It is recommended that a further study be undertaken to measure the time-dependence of the oxidation rate for a range of particle sizes and different materials. This study would provide measurements against which models of oxidation rate as a function of time and particle size can be tested, to give confidence in the use of models to describe dump behaviour in the longer term.

Jan 1, 2000

By Charles T. Staniek

Following a dragline relocation at Agrico's Fort Green phosphate mine in 1986, the recovery plant experienced a significant decrease in flotation performance. Through weeks of trial and error testing, we discovered we could restore recoveries by conditioning feed at pH's higher than we had used historically. The higher pH's essentially increased flotation cell kinetics, although we still do not understand the exact mechanism at work. Armed with new-found appreciation of pH modification, we initiated a program to determine the optimum modifier for us, from both a performance and environmental perspective. Environmental considerations were important because ammonia, the standard industry modifier, is a plant nutrient and higher usage rates could affect the quality, of our recycle process water. This paper describes the research and development work spanning a 3 year period that culminated in making a major change in our reagent suite when we replaced ammonia with soda ash on a permanent full-time basis.

Jan 1, 1993

By David M. Mchaina, Allan E. Hall, W. C. H. Kruining, Alan Coode, Stephen Hardcastle

This paper details an investigation into the feasibility of recirculating mine exhaust air in Saskatchewan potash mines. This project was initiated following a previous study at Ruttan Mine, Manitoba, which indicated that recirculation of exhaust air to reduce winter heating costs was feasible. The potash industry was selected for study because the mines use a minimum of blasting in their production methods and the exhaust temperature is significantly higher than that of most metal mines. These factors simplify the monitoring system required and have the potential for greater waste heat recovery. A series of measurements of underground mine pollutants was made at the main exhaust and intake shafts in order to determine the feasibility of introducing controlled recirculation of exhaust air. An experimental recirculation circuit was created by opening two existing doors situated between the return and intake shafts. During this recirculation trial, the air quality parameters at the intake, mixed intake and exhaust measuring stations were monitored. The results obtained from a questionnaire circulated to the regulatory agency and the major potash producers together with results obtained from underground field studies at Central Canada Potash (CCP) Division of Noranda Minerals indicated that controlled recirculation of mine exhaust air has potential application in these mines either to reduce heating costs and/ or to increase the face air quantities. A recirculation system is to be designed in conjunction with CCP and the Saskatchewan Ministry of Labour, Mine Safety Unit to attempt to implement a working recirculation system for CCP.

Jan 1, 1989

By A. M. Laird

Endako Mines' molybdenum operation is located near the geographic center of the province of British Columbia, Canada. The property is six miles south of the Northern Transprovincial Highway and the northern main line of the Canadian National Railway. The area is broken by high hills covered with dense stands of spruce and pine with vast areas of the valley floors covered with aspen and poplar. The climate is moderate with precipitation averaging 22 inches per year. Approximately four feet of snow accumulates in the winter, and temperatures range from 900 F. in summer to -40° F. in winter. The orebody, a lowgrade porphyry type deposit, occurs in a widespread granitic intrusive which has been locally weakened at the intersection of two regional faults. In this vicinity the quartz monzonite has been further shattered to permit the entry of mineralizing solutions and local dykes. Two types of mineralization occur within the orebody. The most prom¬inent is the six inch to four foot wide continuous quartz veins with characteristic ribbons of molybdenite and frequently finely-divided grains of molybdenite within the quartz. The second type occurs as fine fractures filled with quartz molybdenite in the form of a stockwork halo radiating out from 20 to 200 feet from the quartz veins. Minor hematite, magnetite and chalcopyrite are also present. Mineralization is roughly proportional to the extent of kaolinization in the quartz monzonite, kaolinization being one of three distinct forms of hydrothermal alteration. Pyrite is commonly associated with molybdenum mineralization within the orebody and a pyrite halo is recognized on the south side of the orebody.

Jan 1, 1968

By R. V. Ramani

This paper is based on the thesis that the demand for computer-oriented mining engineers will continue to sharply increase in coming years. It presents the philosophy behind the development of a mine systems engineering program at The Pennsylvania State University. The paper discusses the current status of mining engineering education and the problems encountered in integrating extensive computer background and education into a traditional mining engineering program. The paper analyzes the interrelated roles of research, graduate studies, and continuing education in developing a comprehensive program of study. It is hoped that this program philosophy will be useful to other institutions which are contemplating new programs and courses in emerging technologies.

Jan 1, 1982

By Jeffery Leavy, Ken Davis, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) is a United States Department of Energy facility located in southeastern New Mexico. It is designed for the safe disposal of transuranic radioactive waste in deep geologic salt beds. Westinghouse TRU Solutions, LLC, the managing and operating contractor, undertook a project to simulate the processes at WIPP in order to identify bottlenecks and optimize available resources. The activities simulated in the model included the receipt, processing and disposal of radioactive waste underground, the mining of new areas for future waste disposal and the transportation of salt out of the mine. The complexity of the processes and the interactive requirements between processes required the use of advanced modeling techniques. The simulation model includes a huge number of locations and path network node points, with movement to and from the locations controlled using parameters rather than explicit routing. Information for the timing and sequence of the mining and nuclear waste emplacement operations is brought into the model via spreadsheets. Arrays in the simulation model keep track of past and future events that occur. Routing to the multiple possible positions in the underground mine is done using attributes, and system functions within ProModel in order to allow for a highly flexible sequence of planned events and to reduce the level of effort in creating the ProModel processing. Considerable use of subroutines in the simulation model is utilized for parametric decision-making that is repetitive. This presentation describes the modeling techniques used to accurately simulate the surface and underground operations. The surface and underground operations are considerably different, thus they will be treated in their own sections.

Jan 1, 2002

By J. A. Finch, J. Yiantatos, A. R. Laplante

This paper re-examines the mixing conditions in the collection zone of flotation columns. These have in the past been characterized with a single uniaxial dispersion coefficient, E. The relationship between E and column diameter, Dc, is examined based on residence time distributions (RTDs) in columns of Dc ranging from 5.lcm to 184cm. Results agree with published correlations in chemical engineering, i.e. E a Dc '" , Data explain why pilot columns display significant upgrading between the feed level and the interface, whereas plant columns do not. It also suggests that, for plant columns, the full collection zone (up to the interface) can be considered when calculating the residence time. A mathematical model considering two regions of different mixing was compared to the single E model. Both models adequately fitted measured age distributions inside the column and overall RTDs. Measured and simulated mixing characteristics are compared to those of flotation banks, using a tanks-in-series approach; banks of comparable mixing to columns are identified.

Jan 1, 1988

By M. K. Pathak, A. K. Mukhopadhyay, D. C. Panigrahi

Changes in machinery operating and design parameters often result in unexpected vibrations or changes in the vibration patterns. Vibration in a system is an undesirable element that can cause machinery distress. Potential damage can be prevented by identifying the vibration level that is due to the changed operational parameters. This is necessary for the safe and reliable operation of plant equipment. This paper presents a documented study on vibration events that resulted from alterations in operating and design parameters in a mine ventilation fan and analyzes the causes by defining the sequence of events that led to its performance deficiency. This paper is based on experimental effort to study the vibration behavior of a ventilation fan under varying operating conditions.

Jan 1, 1999

By Roshan B. Bhappu

In situ mining and extraction is one of the Frontier Technologies that is destined to play an increasingly important role in the recovery of metals and minerals in the future. This premise is based on increasing costs of labor and energy, increasing awareness of environmental considerations and decreasing ore grades in the United States. Up to now, in situ mining has been successfully applied to a few favorable situations for the extraction of some evaporites, copper and uranium. However, because of its unique technical, environmental and economic advantages, this versa tile technology will find broader applications for the recovery of above commodities as well as for others which are currently extracted by hydrometallurgical means. This paper traces the development of in situ mining and extraction; stresses its dependence on interdisciplinary science and engineering; discusses its theoretical, practical and economic aspects; and finally presents potential applications of this Frontier Technology.

Jan 1, 1985

By Stephen J. Navin, Francis P. D. Navin

Long-distance movement of various materials by conveyor is becoming common; therefore, it is no surprise that conveyors are frequently found in very long tunnels. In such long tunnels, there is a continual controversy between the tunnel operator's requirement for a maximum of clear space for the conveyor and vehicles and the investor's wish to make the minimum capital investment for excavation. This analysis shows that the question becomes more pressing as the tunnel becomes longer. The result given in this paper is a straightforward method by which an economic and operational optimal tunnel width may be selected for any specified tunnel length. Detailed computational formulas are developed relating costs of construction, vehicle operation, vehicle accidents, and conveyor downtime to both tunnel width and length.

Jan 1, 1985