Search Documents

By Po-Wei Tun, Kuen-Yuh Wu, Tso-Min Shih, Hsi-Chiang Fang

The purpose of this study is to investgate the coal dust explosion characteristics and to search for the prevention methods of the coal dust explosion as well as the propagation of the explosion flame of the middle-bearing coal formation in Taiwan by an open type coal dust explosion apparatus in laboratory. The coal samples were taken from the typical middle-bearing formations of the Sam-Ming,Tai-Ho and Lee-Fong coal mines The rock dusts, the free water mixture with coal dust samples and the interval clean out the coal dust in the testing chambers were applied for preventing the coal dust explosion and the propagation of the explosion flame.

Jan 1, 1993

By J. Y. Kim, S. L. Chryssoulis

Lead ions that originate from galena during the processing of complex sulfide ores migrate onto the surfaces of sphalerite and iron sulfide minerals. This results in poor selectivity during differential flotation. Generally, in sulfide ore processing, the lead-activated minerals float in the Cu/Pb rougher circuit. The surface lead complicates the zinc flotation circuit by lowering the concentrate grade. The effect of lead in the differential flotation of sphalerite from Cu-Pb-Zu and Pb-Zu ores is discussed. Plant and laboratory-test data are interpreted by determining the surface compositions of individual grains of sphalerite and iron sulfide particles. For the first time, surface compositions were determined by using laser-ionization mass spectrometry (LIMS) and time-of-flight secondary ion mass spectrometry (TOF-SIMS). Cationic and cationic species on the surface were analyzed to elucidate the phenomena. It was proven that these new techniques are very useful in understanding the basic mechanisms of a sulfide mineral-flotation system.

Jan 1, 1997

By S. K. Kawatra, T. C. Eisele

In many mining operations, particularly northern open-pit mines, large seasonal variations in grinding slurry temperature can occur. It is shown in this paper that this temperature shift can cause a winter-time loss in autogenous grinding efficiency of as much as 20% if it is not controlled. Laboratory experimentation indicates that much of this effect is due to increases in slurry viscosity as the temperature is decreased. An additional effect may result from changes in rock strength upon freezing, for which possible mechanisms are discussed. However, no effect clearly resulting from rock strength changes has been definitely confirmed.

Jan 1, 1992

By J. Paraszczak

With regards to the cost and profitability of a mining operation, the performance of the equipment employed is one of the key issues. Cost and profitability depend on, among other factors, the reliability and availability of the equipment. In an attempt to reduce equipment downtime, it is indispensable to collect and analyze reliable data and information on failures and maintenance actions. This paper reviews common problems encountered in this respect, with particular emphasis on the lack of uniform terminology and methodology. Recommendations concerning the standardiztion of reliability and maintainability concepts and measures are given. Regarding the benefits that the latter may bring, the paper concludes with a proposal for an industry-wide initiative in this respect.

Jan 1, 2002

By R. E. Johnson, W. Kat, B. R. Palmer, van Sandwijk A., G. Van Weert, S. Honingh

In-plant recycling of dust from iron making BF's creates undesirable circulating loads of volatile trace elements such as zinc and lead. Disposal of such dusts creates environmental problems, hence a separate treatment is indicated. Since the bulk of the zinc and lead compounds occurs in the fine dust fraction; hydrocycloning the slurry from the BF gas cleaning operation results in upgrading the material for treatment. A process has been proposed, whereby the zinc and lead are solubilized from the fine fraction with spent hydrochloric acid from steel pickling. The stoichiometry of this autoclave oxidation process is adjusted to simultaneously precipitate, by oxyhydrolysis, most of the iron for recycling to the BF's. Lead and zinc are successively recovered from the filtrate as low chloride precipitates. This paper describes additional testwork, leading to the design of a pilot plant which was planned to begin operation in 1992.

Jan 1, 1993

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ?Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions became the post-event conditions. ?Search for evidence that either denies or supports the various hypotheses. ?Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

By Sharad Mathur

The purpose of this paper is to present the benefits of high reactivity meta kaolin (HRM) in high performance cement-based systems. HRM, unlike other pozzolans, is manufactured from selected naturally occurring kaolin ore and carefully processed under stringent conditions to result in a consistent product with highly pozzolanic properties. HRM is an ultrafine pozzolan that enhances the mechanical properties (workability and strength) and chemical stability (durability) of Portland cement concrete and cement-based products. HRM is unique with respect to its white color which makes it an ideal choice for architectural applications where visual and aesthetic concerns are critical.

Jan 1, 2003

By G. Johnston, P. K. Chatterjee, S. Holguin

Underground mine planning is largely manual and can demand considerable resources to generate a working plan and to perform limited tests of sensitivity to variations in geological and mining conditions. It is possible to use computer aided mine planning to automate many of the manual procedures to allow the planner to evaluate a number of layouts, extraction strategies, and schedules. his paper examines the simulation and scheduling of an under- ground coal mine operation through the-use of on- screen graphics. The simulation will provide a basis for predicting productivity and other relevant information over a specified number of shifts. The software developed is extremely user friendly and reduces the tedium of repetitive manual calculations inherent to mine planning and drafting to a minimum, thus offering considerable savings in an area that is widely recognized as extremely labor intensive.

Jan 1, 1988

By M. G. Ayat

Engineers in the field of coal preparation are continually striving to increase the efficiency of various circuits used in preparation plants. Undoubtedly, one of the important factors concerning the processing efficiency of a coal preparation plant is improved analyses and control of the processing equipment. The necessary link between the performance criteria of a circuit may be provided through on-line determination of various parameters. Currently, there are a certain number of on-line instruments developed for measurement of ash content of coal (Watt and Sowerby, 1983; Kawatra, 1976; Fauth et al., 1984; Lyman and Chester, 1980), moisture content (Hall et al., 1969), and sulfur content (Stewart et al., 1974). In the case of coal separatory units, these parameters are often directly related to the quality of the product. In other words, the extent of misplacement of refuse in the product, or vice versa, would indicate the performance characteristics of any particular coal washing equipment. Partition curves are therefore established to predict the performance of coal cleaning operations. Conventional sampling and testing is currently the major tool with which partition curves are produced and the performance efficiency of the operation is assessed. While conventional analysis techniques are accurate, they are slow and time-consuming.

Jan 1, 1987

By M. J. Virnig, C. P. J. Van Vuuren, A. J. Botha

The Zadra, AARL and organic elution processes and variations of them are presently widely used to recover gold from activated carbon. Despite this the study of the kinetics of elution have received relatively little attention. It is the aim of this study to investigate the rate processes taking place during elution in both inorganic and organic solutions. Batch adsorption and elution rate and equilibrium experiments were performed. The spatial concentration of gold inside carbon particles at various stages of the adsorption and elution processes were measured with a scanning electron microscope using an image analyzer to control and manage the micro-analysis data. The activated carbon particles exhibited film and intra-particle mass transfer rate- controlled behaviour during adsorption in a caustic aqueous solution at 95°C. Elutions in the aqueous caustic acetone solution at 30°C and the caustic aqueous solution at 95°C were unaffected by change in stirring rate. Elution was modelled by desorption reaction rate-control at the outer surface of the carbon particle. Adsorption and elution isotherms under duplicated solution conditions showed reasonable agreement for the inorganic solution and a large disparity for the organic solution.

Jan 1, 1993

By Jack G. Pippenger

This report focuses on the procedures required to review, prepare specifications, bid, and purchase a fully integrated computer system for utilization by engineering personnel in all phases of mine engineering. The presentation is based on the experiences encountered in 1984 in procuring an engineering computer system at The North American Coal Corporation's Western Divi- sion. A two-phase report detailing the purchasing process and subsequent utilization of the engineering computer system will be given. Special detail is also provided on the final system hardware and software setup.

Jan 1, 1989

By J. J. Davis, D. G. Osborne

The Australian coal industry is characterised by efficient fines recovery, and the climate does not dictate the use of thermal drying. With the increasing trend to underground mining and hence finer ROM coal, and market pressures for reduced product moistures, dewatering issues are assuming increasing importance in the Australian coal industry. The greatest potential gains in dewatering performance undoubtedly lie in the treatment of finely sized material. This paper examines the dewatering issues which have been recognised by the Australian coal industry, and describes current Australian research in this field.

Jan 1, 1995

By M. R. Bowie, J. M. Barker, J. S. Hingtgen

Techniques of testing perlite require a combination of art and science. The modifications made to the perlite Corp. vertical laboratory furnace include addition of instrumentation, flowmeters, vibrators, automatic feeders, and regulators. The basic testing sequence consists of expanded density, furnace yield, compacted density, percent sinkers, and compaction resistance. These tests are modified versions of those specified by the Perlite Institute. This sequence is designed as a preliminary evaluation of a material's suitability for horticultural-aggregate end uses rather than a detailed measure of filtration capability.

Jan 1, 1988

INTRODUCTION The role of comminution and related unit operations in mineral processing applications is of major importance. This is especially true in terms of operating costs, since these unit operations represent the major fraction of the overall processing costs. Due to the broad scope and the large number of unit processes and machines involved, Section 3 is divided into five subsections. In Section 3A, General Aspects of Comminution, topics covered include history, terminology, particle¬size distributions, classes of comminution machines, testing and calcu¬lation procedures, and simulation and modeling. In Section 3B, Crush¬ing. the subjects include jaw crushers, gyratory crushers, cone crushers, hammermills, and impactors. The chapters of Section 3C, Grinding, cover aspects common to tumbling mills, ball mills, rod mills, autogenous mills, pebble mills, roller mills, fluid energy mills, other types of grinding machines, and grinding costs. Section 3D, Classification, coverage includes classification theory, hydrocyclones, and mechanical classifiers, and in Section 3E, Screening, the topics presented are classes of screens, selection of vibrating screens, sieve bend screens, and screening media. About five years after the Handbook was begun, Section 3 was unfortunately without an editor or contributors for over half of the chapters. A committee was then organized to expedite completion of the section. When this committee contacted the persons who had agreed to contribute to the section, it was found that many of them wished to resign from their earlier voluntary obligation to AIME. Therefore the committee had to find new contributors for these chap¬ters in addition to other chapters in Section 3. Since there had been no previous effort to locate contributors for Air Classification, Dust Collection, and Washing and Scrubbing, it was agreed to delete these subsections. In Section 3, equipment availability, capacity, and performance data from various manufacturers and users are provided for engineer¬ing use. Selected data from existing installations are also included. The machines that are being used in comminution, classification, and screening are described in detail, and drawings, photographs, and diagrams are presented to supplement the descriptive material. The editors thank and acknowledge the generous effort of the many contributors, some of whom were called upon five or more years after the Handbook was started. It is regretted that Fred C. Bond, who was a member of the committee formed to complete this section, was deceased before the section was finished. During the time that he worked with the committee, he contributed a great deal as an author and councilor.

Jan 1, 1985

By A. G. Journel

The regionalization of tungsten grades at the deposit represents an ideal case for anisotropic hole-effect variogram modelling. The modelling technique is presented step-by-step and the consequences of the model on block kriging are indicated.

Jan 1, 1982

By G. G. O. O. Uwadiale

A number of Nigerian iron ore deposits have been upgraded to the specifications of concentrates for the blast furnace and the direct reduction iron- and steel-making plants. Depending on the mineralogy of the ore deposits, the techniques of oil agglomeration, magnetizing reduction, washing and scrubbing, gravity concentration, and reverse froth flotation have been utilized. A mode of distributive management of the deposits, in the direction of their technoeconomic utilization in the country's developing iron and steel plants, is presented.

Jan 1, 1990

By Allen V. Reicks

This paper reviews the impact of the idler set on the performance of belt conveyors. Idler rolls as part of the load support system and their interaction with the conveyor system will be discussed. in particular, the rotating performance of the individual idler roll concentrating on the rotating resistance and life of the bearing and seal design are addressed in detail. A basis for the development of performance specifications for use in conveyor design that takes advantage of the idler manufacturers design and manufacturing expertise is discussed.

Jan 1, 2008

By G. F. Revey

Most commercial explosives contain from 70% to 94% (by weight) ammonium nitrate. When some of the explosives end up in shot rock and ore, through either spillage or incomplete detonation, ammonia and nitrates can leach into the ground water. In recent years, state and federal regulators have applied more stringent water-quality standards, particularly at new mines and development projects. When mining conditions permit, bulk ANFO, a mixture of ammonium nitrate and fuel oil, is the explosive of choice. ANFO is less costly than other explosives but it dissolves readily in water. Several case histories in the United States and Canada show a clear connection between uncontrolled losses of bulk explosives and high nitrate levels in mine effluents. Mining companies have tried several approaches to reduce ammonia and nitrate levels in groundwater. These approaches range from controlling explosive losses to treating the mine effluents. In this paper, controlling explosive losses is addressed For both packaged and bulk explosives, guidelines to limit losses during storage, handling and use are described in detail.

Jan 1, 1997

By M. R. Stokes

Over the recent years there has been an increase in the application of retreat mining on longwall faces as mine operators strive for ever greater productivity. The purpose of this paper in then to review current practice as a starting point and then move forward to discuss the future geometry's that a longwall face may take. Single and double production zone three roadway faces are assessed. All possible configurations of three roadway faces are defined. Unsuitable configurations are rejected after analysis of broad ventilation issues. The remaining configurations are then assessed on an operational basis, this includes: limits on retreat synchronisation, structure of centre gate, floor bulging and equipment installation. The remaining viable configurations are then further assessed on ventilation issues, this includes: provision for gas control/gas fringe, face climate and balancing of face flows. Possible face climate is assessed using numerical simulation of the various configurations, the predicted dry/wet bulb temperature and predicted levels of heat stress indices are given and discussed in detail, along with face flow balancing. The necessary conditions required for the successful operation of a double production zone three roadway face system are formulated, together with conclusions as to the possible level of application.

Jan 1, 1997

By Jan K. Wolski

This paper presents a simple method for determining air temperature gradients along a tunnel with time-dependent intake air properties. The variable intake air properties may be the flow direction and rate, air temperature and humidity, and the carbon dioxide content. The transient intake air properties are simulated by a series of steady intake air conditions, using a superposition method. The mathematical model was verified by reduced-scale experiments in the Waldo mine. The method may be usefull in conditions where the computation speed is more important than the precision of the results.

Jan 1, 1995