Search Documents

By D. X. Tang, G. Wilson, S. S. Peng

Design and implementation of a roof bolting plan requires reliable geotechnical information of strata, such as rock strength, and locations of interfaces and voids/fractures. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way to gather information on the geological structure within the bolted horizon. The purpose of this research project is to develop a method for identifying the geological features in the mine roof strata based on drilling parameters of roof bolter. The criterion for void/fracture prediction has been developed and proven valid. This paper focuses on the estimation of the strength of roof strata by using drilling parameters. Based on the results of a series of underground and laboratory tests, feed pressure is found to be the most sensitive parameter when the strength of roof strata changes. Moreover, it was also found that both penetration rate and rotation rate have obvious impact on the magnitude of feed pressure. Based on these findings, the criterion for the estimation of roof strata strength has been developed using the relationship among feed pressure, penetration rate and rotation rate and implemented in MRGIS.

Jan 1, 2006

By Forrest C. Neil, Clint J. Keifer

The pollution of our water supply, Lake Michigan, is a continuing threat so long as our overflows from combined sewers exist. The problems have become even more acute during recent years, due to the increase of paved area- which accelerates and enlarges the flows of storm water. After each storm, mixtures of raw sewage and storm water spill into our waterways. If the storm is too large for the drainage systems, the mixture backs up into our streets and basements. Under severe conditions, it may even become necessary to open the locks, and discharge the polluted water into Lake Michigan. Consider the scope of the problem, as shown in Figure 1. The area in which combined sewers exist is 375 square miles, located in the central parts of Chicago and 49 suburbs. There are an estimated 640 overflow outlets to the waterways, each requiring attention. The capacity of outlets tributary to the waterways has increased dramatically over the years. Each time a pocket of upstream flooding is drained into the channels, the problem of its rapid disposition increases. Another difficulty is that the bottom of our waterways is covered with a blanket of accumulated sludge, ranging in depth up to 3-feet. This material harms the water quality by depleting the supply of oxygen dissolved in the water ... a final

Jan 1, 1997

By Haydn H. Murray

Kaolin is defined and described as an industrial mineral. In addition the types of deposits -primary and secondary are defined and the genesis of kaolin from feldspars and other minerals discussed. The major deposits of the world found in the United States, Great Britain, Brazil, and Czechoslovakia are described along with many of the minor kaolin deposits. Four areas which have very large deposits of kaolin could, with technological breakthroughs to reduce viscosity significantly, become important factors in supplying the world markets which are increasing year by year.

Jan 1, 1977

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

By Steve Kral

President Bush’s National Energy Program and his Clear Skies Initiative both emphasize the use of coal to help meet the nation’s growing energy needs. And why not? Coal is currently responsible for more than 50 percent of the nation’s electricity generation. That fact, though, seems to be lost on policy makers, the environmental community and the public. Critics of coal advocate the increased use of renewable energy sources and the increased use of natural gas. Renewables, though, are only capable of generating a tiny fraction of the power required. Natural gas is expensive. And natural gas production cannot keep up with demand, especially given the nation’s increasing energy needs.

Jan 1, 2003

By Robert Harris, David Duncan

The Samira Hill gold mine represents the first commercial gold project for the landlocked country of Niger in West Africa. It began production in October 2004 as the result of over 10 years of exploration and development work. There were several administrative, social and technical challenges that had to be overcome to realize the successful development of the project. The Samira mine is located on the geological structure known as the ‘Samira Horizon’ which is developing as a promising district for additional discoveries and other mine developments.

Jan 1, 2005

By Arthur Darby

The city of Kuala Lumpur was founded in 1857 by miners seeking tin near the confluence of the Klang and Gombak rivers. The rapid development of the city and surrounding area since independence has led to more rapid runoff during rainstorms and to gradual canalisation of the rivers with some restricted sections. The outcome has been more frequent and more severe floods (Abdullah 2006). At the same time the centre of Kuala Lumpur has become a modern inter-national city with tall office buildings, hotels, and shopping centres connected by a network of wide roads and commuter rail systems. With these the cost of dislocation during floods has risen as has the cost of making good damage afterwards. The Government of Malaysia considered these consequences unacceptable and sought ideas from the private sector for a solution. Potential solutions consisted of variations on the themes of bypassing the city centre with a flood relief tunnel or of providing off channel storage or a combination of both. Since under Malaysian law a tunnel cannot be constructed under private property unless this is first purchased or agreement reached with the owner, it was necessary for most of the tunnel alignment to run below existing heavily congested roads. After considering these facts Gamuda Berhad and MMC Berhad, two leading Malaysian development and construction companies, decided to propose to Government an innovative solution in which the tunnel would be used to carry road traffic except during floods.

Jan 1, 2008

Ceremonies for the induction of five mining industry pioneers into the National Mining Hall of Fame will be on Sept. 12, 2009 at the Charles F. Barber Pavilion of the Museum Convention Center in Leadville, CO. The five inductees are: Paul A. Bailey, 82, Richard T. Moolick, 89, William Braden and Alonzo Pawling and Henry Harnischfeger. Paul A. Bailly was president of Bear Creek Mining Co., the U.S. exploration subsidiary of Kennecott Copper, from 1961 to 1967. In 1968, he joined Occidental Petroleum Corp. and was tasked with creating the company?s international mining division, Oxymin, which he led as president through 1983. During his distinguished career, Bailly participated in numerous significant mineral discoveries, developed a new exploration philosophy and made important additions to the mineral exploration literature. William Braden was the first to recognize the immense potential of the El Teniente orebody in Chile. He founded Braden Copper Co. and developed the El Teniente Mine which now, 100 years later, remains the world?s largest underground copper mine. Braden?s endeavor survives to-day as the El Teniente division of the Chilean state copper company, CODELCO. T. (Dick) Moolick established a lasting legacy in the mining industry, first during a 35 year career with Phelps Dodge Corp. and then as the driving force in establishing the National Mining Hall of Fame and Museum in Leadville. The Hall of Fame and Museum ? a monument to the memory of the men and women who pioneered the discovery and development of the United States? natural resources ? has become one of the fi nest museums in the western United States.

Jan 1, 2009

By William R. Yernberg

A conference on coalbed and coal mine methane was held March 27 and 28, 2000, in Denver, CO. The conference, organized by the Strategic Resource Institute, was attended by leaders in the coal mining and gas energy industry. The conference focused on the recovery of methane from coal beds as an energy resource and the removal and utilization of coal-mine methane (CMM) related to underground coal mining. The two-day conference discussed methane resources around the world, methods of recovery, methane markets, underground coal mining, health and safety issues and environmental issues related to methane. The consensus among the presenters is that the future looks promising for coal bed methane (CBM) and CMM.

Jan 1, 2000

Bortech’s BoreClad corrosion protection system will be displayed at MINExpo. BoreClad is an innovative system for inside diameter cladding of nozzles, tubes and other circumferential devices. Pressure vessels, mud pumps and other mining equipment must be protected from corrosive caustic chemicals. Usually manufactured from mild steel, they can be clad with a protective material, such as stainless steel, to provide corrosion resistance. However, most welding processes leave voids where corrosion can damage the base metal. BoreClad provides void-free welds by combining gas metal arc welding with automated feed and rotation of chuckable parts. Workpieces of up to 915-mm- (36-in.-) long with a 460-mm- (18-in.-)swing can be clad with stainless steel, Iconel or other exotic metals. In addition to eliminating the voids associated with hand welds, BoreCladcan lay more than 2.2 kg/h (5 lbs/hour) of metal. That is a significant reduction in weld time. Web sitewww.bortech.com.

Jan 1, 2004

By Clayton V. Deutsch

Indicator Kriging (IK) is being commonly applied to mineral resource assessment problems. More recently, indicator simulation has also been used for sensitivity analysis and difficult change of support problems. The essential theory underlying indicator geostatistics has not changed since its introduction 10 years ago; however, the last decade has produced many important developments in its implementation. The objective of this paper is to consider some of the more important implementation details. Examples from the Porgera gold deposit in Papua New Guinea are used to illustrate the steps in an indicator geostatistical study and the importance of various implementation decisions. Specifically, in many precious metals deposits the continuity of the grades is typically quite anisotropic. This anisotropy varies in both magnitude and direction throughout the deposit. Building a model of this anisotropy can considerably improve the local kriged or simulated points. One approach to build this model is presented. In addition, there is typically more than one mineralization style and geological rock type; the spatial character of the mineralization can be quite different within each geological rock type. The rational treatment of anisotropy and geological subdivisions is common to all mineral resource assessment procedures; the importance of this qualitative geological information is not diminished with more sophisticated techniques such as indicator kriging. This paper presents an overdue comprehensive look at the practical aspects of indicator methodology. Many of the techniques and procedures documented in this paper have been developed during the course of detailed mine feasibility studies.

Jan 1, 1992

By M. W. Smith

Pennsylvania has 2500 miles of streams that do not meet water quality standards due to acid mine discharge (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. Pennsylvania is using a watershed-based approach to abating AMD which includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Watershed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves which could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 1999

By Stephen M. Smading

The Jinping-II hydroelectric project in China features four parallel headrace tunnels approximately 18-km- (11-mile-) long. Two will be excavated by tunnel boring machines (TBM) and two by drill-and-blast. A nearby fifth tunnel is being excavated by a 7.2-m (23.6-ft) TBM to draw down ground water in advance of excavating the headrace tunnels. Unique onsite assembly of a 12.43-m (40.7-ft) main beam TBM and backup system was completed on Sept. 18, 2008 in the remote mountains of the Sichuan province. The equipment was assembled onsite, without previously having been assembled and tested in a factory, using a method called onsite first time assembly (OFTA). This paper addresses the following topics: ? Project description including geology and terrain. ? The decision process leading to onsite, first time assembly, the assembly process and logistics, and lessons learned. ? Design features of the TBM and backup system. ? Operational history from startup to the writing of this article.

Jan 1, 2009

By Kadri Dagdelen

Design of the ultimate pit limit to direct long range mine planning has been a celebrated problem in the mining industry, and in mining academia, since 1965. Although many papers have been presented on this topic, even today, there is not a single solution technique which is widely accepted and considered universally best. Many philosophical differences exist among the pit planners concerning the use of different methods and it appears that resistance is very strong towards accepting other techniques if you are a believer in one. Whatever the case might be, the pit parameterization technique for the ultimate pit limit design is the latest and takes a different approach than its predecessors. There are already a number of papers which discuss the concepts involved (Francois-Bongarcon, 1976; 1978; 1980; 1981); however, the aim of this paper is to fill in some of the gaps which are thought to be missing in the previous discussions and, in addition, to present the recent research done on the subject at the Centre de Geostatistique de l?Ecole de Mines de Paris in Fontainbleau, France. This paper is divided into two parts. The first part will discuss practical aspects and interpretations of pit parameterization concepts with- out using mathematical or theoretical arguments; the reader who is interested in the theory should refer to Francois-Bongarcon (1978). The second part will present an approach to obtain a complete double parameterization of reserves using an inexpensive (computer costs) single parameterization algorithm. A case study of this approach is also included.

Jan 1, 1982

By Tony S. Calayag

Throughout the mining industry today, new bearing materials - ZA* high-performance zinc-aluminum alloys - are reducing costs of maintaining and rebuilding a wide range of equipment. As replacements for bronze bearings, installed in original equipment at the plant or during maintenance and repair operations in the field, the zinc alloys frequently provide better or equal performance at lower cost. The ZA Alloys The ZA alloys are a family of three high-performance zinc-aluminum alloys that compete in cost and performance with cast iron aluminum and bronze. The growing number and uses testifies to the versatility of these alloys and is encouraging their consideration in a wider range of applications. The ZA alloys are referred to as ZA-8, ZA-12, and ZA-27, the numbers corresponding approximately to the percentage of aluminum each alloy contains. ZA-8 is a permanent-mold casting alloy and is usually selected for decorative purposes; ZA-12 provides both performance and cosmetic benefits; ZA-27 offers the greatest functional strength. The term high performance ZA alloys distinguishes them and their improved engineering properties from traditional zinc die casting alloys. Maintenance Savings At its mine in Timmins, Ontario, Kidd Creek Mines Ltd. operates over 40 Joy VCR- 150 crawler-mounted air-powered rock drills. Most of the drill components undergo severe stress as the drill batters through the under-ground rock. As the components wear, the drill bits wobble; when the wobble becomes excessive, the drills are rebuilt. In the gear train, which rotates the drill steel, there are three planetary gears with - historically - bronze bushings. Since the planetary gear bushings are wear items, they are routinely replaced during overhaul. The bronze planetary gear bushings (three bushings per assembly) were replaced up to five times annually. With 43 drills in use, bushing consumption approached 600 per year. At the manufacturer's replacement part cost, the 600 bushings and gears would cost more than $20,000 a year. Even though a major saving was achieved by having the bronze bushings manufactured locally, the 600-unit annual usage provided ample incentive to investigate other ways of lengthening drill life and reducing the part costs. One approach was to consider using a bushing material that offered good bearing properties, but was lower in cost. About three years ago, ZA-12 zinc-aluminum casting alloy, costing less than half as much as bronze, was evaluated and selected for testing. One hundred ZA bushings were manufactured and placed in service as the drills came in for rebuilding. At the next rebuild the "drill doctor" (drill maintenance mechanic) noticed that, although the bronze bushings were completely destroyed, on occasion the zinc alloy bushings were not. In addition, he noted that some of the ZA bushings showed less wear than the bronze bushings. Because the bushings were changed routinely during each overhaul, the actual operating life of each bushing was not determinable. Therefore, it was not possible to statistically compare the life of the ZA bushing against the bronze. However, the desired life of the part was from overhaul to overhaul. So the ZA alloy obviously met the objective, giving equal or better life than bronze at a significantly lower price. Based on the favorable results of the testing under actual operating conditions, Kidd Creek maintenance personnel decided to switch permanently to the ZA bushings for rebuilding the VCR-150 rock drills. Original Equipment Application As one of the leading companies marketing the ZA alloys, as well as a zinc -copper-silver mining company, Kidd Creek is interested in developing applications for the alloys by original equipment manufacturers such as joy Manufacturing. Kidd Creek marketing representatives provided joy with information on the Timmins mine tests, along with ZA-12 bushings for evaluation and testing. Based on this information, joy installed ZA bushings in 12 new VCR-150 units and delivered them to customers for use in such areas as granite quarries and copper, lead, zinc, and limestone mines. During the following year, joy engineers closely monitored repair reports to verify the performance of the ZA part. The engineers' findings convinced them of the advantages of ZA-12. As a result, joy now uses ZA-12 bushings in the manufacture of its VCR-150 air tools. Advantages for Casters and Users In the foundry, the new alloys have proved their castability and profit potential in sand and metal permanent-mold processes, as well as the new graphite permanent-mold gravity casting process. The energysaving, pollution-free and ease-of-machining benefits they offer are important to all of these processes. Most recently, the high-performance alloys entered the arena of cold-chamber die casting, where they provide properties beyond those of

Jan 7, 1983

By M. Dobbins

The advent of the more efficient and effective rare-earth roll (RER) separator in the early 1980s began a new era of dry magnetic separation. The RER units quickly became the separator of choice within the materials processing industry. Though RER separators are now commonplace throughout the world, only modest advancements have been made to the original design. This paper details recent, more significant, rare-earth magnetic separation developments. These developments maintain the best features of existing technology while minimizing shortcomings. The discussion includes discerning features that aid in better metallurgical performance. Also discussed are improved mechanical aspects that allow for both easier operation and maintenance. Performance details from various test programs are included.

Jan 1, 2010

By F. Grajales Muñoz

The Ciénega project, now under construction by Peñoles group, is located in the mountains of northwest Durango, Mexico. The gold and silver deposits are found in a 4-km (2.5mile) long system of veins. An underground operation will be built. The planned 1 kt/ d (1100 stpd) process plant will contain a countercurrent cyanide circuit for oxide ore and a flotation circuit for sulfide ore. Considerable resources have been devoted to the development of infrastructure in the isolated location, as well as for the mitigation of environmental impacts. Startup is scheduled for the third quarter of 1994. Ciénega’s ore bodies consist of quartz veins containing gold, silver, lead and zinc values. The vein thicknesses vary from 2 to 10 m (6.5 to 33 ft) with a northwest trend and nearby vertical dip. Veins are hosted in Tertiary volcanic rocks. The district has intermittently been explored since 1971 by Penoles. After the third series of diamond drilling and direct development work on vein, Peñoles decided to begin project construction.

Jan 1, 1994

This paper describes major technical developments in rod mill design and operating practice since its introduction into the North American minerals industry over fifty years ago. The basic operating characteristics of the wet, overflow rod mill are described, and significant operating variables are reviewed in terms of their effects on mill power draw, power efficiency, and practical aspects of circuit operation. Key factors for improving the economic performance of rod milling circuits are identified.

Jan 1, 1986

In this study, the flotation performances of ethoxycarbonyl thionocarbamate (ECTC), dialkyl thionocarbamate (DATC) and xanthate copper sulfide collectors are compared by the structure-reactivity relationship using generalized perturbation theory and density functional calculation at the B3PW91/6-31G(D) level. The electron-donating power of xanthates is strong and, therefore, xanthates can strongly react with metal cation on the surfaces of copper and iron sulfide minerals through the formation of normal covalent bonds. This explains the poor selectivity of xanthates and also the high pH levels (above 13) required for the flotation separation of copper/iron sulfide minerals. DATCs are more selective for copper sulfide flotation, particularly against gangue iron sulfides. Although less powerful than xanthates, DATCs can perform copper/iron flotation separation at lower operating pH (commonly at pH levels below 11.5). ECTCs use an ethoxycarbonyl replacing an alkyl N-substituent in DATCs. The presence of the ethoxycarbonyl group effectively changes the functional group of collector from -C(=S)NH- to -C(=S)NHC(=O)-. The strong electron-withdrawing ethoxycarbonyl group adjacent to the C=S group decreases the electron density of the sulfur atom, which improves ECTC?s selectivity against iron sulfide minerals at slightly alkaline conditions. The lowest unoccupied molecular orbit (LUMO) of ECTC, which is constituted by the pz-orbit of every atoms in the conjugate -O-C(=O)-N-C(=S)-O- group and which is pleased with accepting richly d-orbital electrons (feedback electrons) from the (t2g)6(eg)3Cu(II) or t6e4Cu(I) configuration of copper cation on the surfaces of copper sulfide minerals, resulted in the formation of dative p-bond. The iron atom, which has a (t2g)6Fe(II) or (t2ga)3(ega)2 Fe(III) configuration on the surfaces of iron sulfide minerals (Fe(III) is the predominant composition at alkaline conditions), has difficulty in offering its d-orbital electrons (feedback electrons) to ECTC?s LUMO. ECTC collectors are powerful for copper sulfide minerals and very selective against iron sulfides, which has been further confirmed by UV spectra and bench-scale and industrial-scale flotation tests.

Jan 1, 2008

By K. Donahue

Clay minerals play an important role in the gravitational stability of man-made rock piles by affecting geotechnical and hydrological characteristics of the material. The Goathill North rock pile at the Questa Mine in northern New Mexico has been the focus of a multi-disciplinary study to determine the effect of weathering on rock pile stability and in particular to determine if clay minerals are forming in the rock pile due to surface weathering. The results of x-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses indicate the clay minerals found within the fine-grained soil matrix of the rock pile are of hydrothermal origins and did not detect any neoformation of clay minerals. The foremost mechanism for an increase in clay minerals within the rock pile is the physical break down of hydrothermally altered rock fragments to release hydrothermal clay minerals. The hydrothermal clay minerals within the rock pile show evidence of weathering by the dehydration of smectite from 2-water to 1-water interlayers within the clay mineral structure. This dehydration is most likely due to higher temperatures and low relative humidities in the Goathill north rock pile during surface exposure.

Jan 1, 2009