Search Documents

By Wendy M. Brunner

A 70% excess of mesothelioma, an asbestos-related cancer, has been reported among men in northeastern Minnesota, where iron mining has been the major industry. The Minnesota Department of Health has studied iron miners who developed mesothelioma to identify possible sources of asbestos exposure. A database of all Minnesota residents diagnosed with mesothelioma between 1988 and 1996 was linked to a database of approximately 72,000 current and former Minnesota iron-mining employees to identify cases who had ever worked in the mining industry. The job histories of the cases were examined to determine if any of their jobs could have involved exposure to commercial asbestos. Seventeen individuals diagnosed with mesothelioma in Minnesota between 1988 and 1996 were found to have worked in the iron mining industry. Of the 15 for whom adequate work histories were available, 14 had identifiable sources of exposure to commercial asbestos in jobs held both inside and outside of the mining industry. The time between employment in these asbestosexposed occupations and the diagnosis of mesothelioma is consistent with the 20 or more year latency period that has been observed in other studies of this cancer. © 2007 Elsevier Inc. All rights reserved. Keywords: Mesothelioma; Asbestos; Iron miners; Taconite; Epidemiology; Case series

Jan 1, 2007

By D. Loring, J. Almgren

Climax Molybdenum Company’s Henderson Mine is a large panel caving molybdenum mine located about 43 miles west of Denver, Colorado. Three Joy M120-72-880 fans are installed in parallel on the No. 1 exhaust shaft. Throughout the mine’s history, ventilation changes such as the completion of the No. 5 exhaust shaft have decreased the utilization of these fans. To optimize fan performance they have been run with the full complement of 16 blades, down to as few as four blades. Since the completion of ventilation upgrades associated with the Henderson 2000 project, one surface fan has been operated under normal conditions with 10 or 12 blades. With the completion of a new network model of the Henderson ventilation system, a tool was built to develop fan curves for possible future fan configurations and predict future fan performance. This paper describes the tool and its use at Henderson.

Jan 1, 2007

By M. J. Farrell

Mining is a significant emitter of greenhouse gases and is the focus of increasing attention from green groups and regulators. Miners need to know their own carbon emissions and how they compare with the rest of the industry. Miners and mining companies need to know where they fit in the emissions curve. Who is in the bottom quartile? This article is based on research report data from minecost.com and Metalytics Pty Ltd which detail the specific carbon dioxide emissions for 208mines producing 90% or more of western world copper, zinc, lead and nickel in 2007. The copper and nickel mines also include Norilsk in Russia, KGHM in Poland and Kazakhmys in Kazakhstan. This is the first time that such information has become available.

Jan 1, 2009

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007

By S. J. Schatzel

Longwall coal mine operators in the US are required to ventilate multi-panel longwall districts but may have little or no knowledge about what happens to the ventilation air between the inlet evaluation points (IEPs), bleeder evaluation points (BEPs), and bleeder fans. The effectiveness of bleeder performance can directly influence the ability of a ventilation system to remove and dilute coal bed methane emissions. Consequently, the performance of coal mine bleeders is an important aspect of underground worker safety. U.S. coal mining stakeholders have acknowledged their belief that the T- junction split at the longwall face tailgate corner is very important in controlling the distribution of ventilation air. The percentage of air directed inby towards the bleeders and bleeder fan and outby to the submains is often not well-defined and can vary over the life of a longwall panel. To obtain direct measurements of bleeder performance, a tracer gas, sulfur hexafluoride (SF6), was released into the intake air stream along the panline of active longwall panels and in the bleeder/gob ventilation air inlets of an inactive panel. Tracer gas sampling was conducted underground using tube bundles attached to permissible vacuum pumps in the gateroads, former gateroads, and bleeders. Surface tracer gas monitoring was also conducted from operating gob boreholes and from bleeder fans. Testing was performed on multiple longwall panels which included various phases of longwall development and variable path lengths of ventilation air transport to bleeder fan installations. The applied methodology defines and describes coal bed gas pathways, rates, and volumes of movement at the bleeder/gob interfaces, and indicates flow rates for air/gas mixtures within these gobs. These findings are reported for three stages of longwall extraction using direct field-based measurements. Changes in the T-junction ventilation air distribution over the life of a longwall panel and its variable effect on panel ventilation airflow are discussed. These findings will assess the effectiveness of commonly applied ventilation strategies for improving air distribution and ventilation controls to meet statutory requirements and to achieve the desired ventilation patterns through multiple phases of longwall panel extraction.

Jan 1, 2011

By B. C. Vargas

The Toulon tunnel project is a key component of the Highway corridor on the French Riviera between Marseille and Nice and is a fundamental transportation infrastructure for the region. The first design studies started in the 1960?s. The tunnel project is made of 2 separate tunnels: South and North tunnel. The North tunnel was built between 1992 and 2002 after 10 years of difficult construction (for example, on March 15th, 1996, a collapse of the tunnel in the ?Marchand Area? generated a sink hole in the city Center, causing 20 months delay). The South tunnel alignment runs parallel to the North tunnel at the same depth below Toulon historical downtown (20 to 40m depth with some areas with less than 10m of cover). The Risk management program was studied to be a State of the Art program in urban tunneling construction. The Hydro Geological Context The whole project area is covered with backfills and colluviums of 1 to 4m thick. The Schist, marls and sandstones, randomly distributed along the alignment below the first layer have different characteristics. While the Schist are pretty compact, the marls are fractured. The other layers have very different characteristics, and many faults are located along the alignment, especially in the limestones. The Breccia are heavily decompressed and deformable, as well as the other soils located in the Marchand Area. This 80m long area is where the settlements need to be controlled with an extensive monitoring program. The complete Geological profile is presented in Figure 1. [ ]

Jan 1, 2012

M.S. Azun I have many objections to the content of the author's paper. Before discussing it, however, I would like to repeat the property of semivariogram function. Second order stationary properties of regionalized variables (ReV's) such as semivariogram function y(h) are perfectly known in geostatistics. Also, the kriging equations in the language of mathematical statistics using second order stationary properties are well understood. However, the way to use the sample (estimated) semivariogram function in any one of the kriging procedures is vague. The sample semivariogram function is given as follows: [ ] where N is the total number of samples, Xi is the sample value at the i - th location, Xi+h is the sample value at the i + h - th location, and h is the distance among the samples. An estimation variance of sample semivariogram function of first lag is smaller than that of higher order lag. The theoretical semivariogram function reaches the variance of samples asymptotically. But this is not easily observable because of the larger variation involved in the estimate of semivariogram function. In general, an estimation procedure is done for h = 0, 1, 2, up to the greatest integer less than N/2, even though sample semivariogram function can be computable through N-1. After estimating semivariogram function, the critical question of how to model sample semivariogram function arises. As seen in the above equation, sample semivariogram function is discrete and can be smoothed by the model being selected. Therefore, modeling of sample semivariogram function is the most important step in geostatistics. It not only smoothes a discrete function but also affects the results of the kriging procedure. When the only aim is to model the semivariogram function, which is the basic point of the author's paper, one can employ any fitting techniques, such as curve fitting, or any arbitrary functions, which are called submodels in the paper. The term "arbitrary function" is used rather than "submodel" because there is no basic understanding of developing them. The author suggests that the sum of those submodels can also be used for the modeling of sample semivariogram function. The combination of any arbitrary functions brings many problems instead of giving an insight of the domain structure considered. The author used two arbitrary functions and the nugget effect in response to sample semivariogram function (Fig. 10). For the same example, he stated that the parameters involved in the mixed arbitrary function model can be accepted when the discrepancy between sample semivariogram function and the model is small visually. For verifying the fitting behavior of any selected model, one should not be contented with the visual satisfactory. Some statistical measure such as goodness of fit has to be used. The author's practice is no more than an exercise in curve fitting without any fundamental understanding or conceptualization of the underlying physical mechanism. Furthermore, the selection of any model is not an easy task if the purpose is the search for the "best" response to the observed second order properties of ReV's. I suggest that the Markovian model (Azun, 1983), on the basis of a theoretical understanding of underlying mechanism, which gives more information about the occurrence of regionalized variables, is used to respond all properties of ReV's. There are a lot of problems for modeling of one-dimensional sample semivariogram function. Thus, it is not appropriate to go to higher order dimensional sample semivariogram function modeling. In the meantime, I would recommend that one can connect the values of standardized sample semivariogram function rather than simple values of semivariogram function in the two-dimensional estimation. The standardized values can be computed in dividing the semivariogram function value by the number of sample pairs involved in each lag regardless of the directions. In conclusion, geostatistics is an interdisciplinary area in mining that uses the principles of mathematical statistics. Thus, it should not violate any probabilistic and statistical rules. When Matheron was developing the theory of geostatistical study in the early years of geostatistics, many mining people had a reservation accepting the geostatistical tools. However, this does not mean that we, the geostatisticians, might try to convince those people using some "strange" tools or rules as some authors implied (Baafi and Kim, 1984). Instead, we have to develop and explain the geostatistical tools staying only in the framework of statistical concepts and properties. References Azun, M.S., 1983, "Stochastic Process Modeling of Spatially Distributed Geostatistical Data," Columbia University, Ph.D. Thesis. Baafi, E.Y., and Kim, Y.C., 1984, "Discussion - Comparison of Different Ore Reserve Estimation Methods Using Conditional Simulation," Mining Engineering, Vol. 36, No. 3, p. 280. Reply by J.M. Rendu The interactive method proposed by Rendu allows practitioners to develop semivariogram models that take into account not only the numerical information obtained by sampling, but also highly significant additional information that often cannot be quantified. The geology of the deposit - including hypotheses concerning its genesis, sampling methods, assaying methods, and mathematical methods used to calculate the semivariograms - all have an influence on the numerical results obtained and on how these results should be interpreted. If all the information concerning the spatial distribution of values in a mineral deposit was contained in the sample values, it could be argued that statistical techniques alone would produce optimum models. However, this is rarely, if ever, the case. Methods that allow the user to take into account his experience and his geologic understanding of the deposit should not be rejected for the sake of theoretical statistical purity.

Jan 11, 1985

By V. T. McLemore

Petrographic analysis of rocks is traditionally performed with optical microscopy using thin sections and point counting. However, this does not provide accurate mineral proportions for sedimentary, volcanic, and soil-like material, because rock fragments, groundmass, and matrix are not identified as specific minerals. In addition, groundmass phases in volcanic rocks can be too fine to identify individually, and making thin sections of intact soil-like material is difficult because much of the material is not well cemented. ModAn is a normative calculation that estimates modes ??by applying Gaussian elimination and multiple linear regression techniques to simultaneous mass balance equations? (Paktunc, 2001) and allows location-specific mineral compositions to be used. One of the features of ModAn that makes it appropriate for this study is that it can model one of several sulfide minerals. Mineral compositions for Questa minerals were determined from electron microprobe analysis and entered into ModAn. Then by combining and normalizing results, bulk quantitative mineralogy can be determined using ModAn, petrographic observations, electron microprobe analysis, clay mineral analysis, and the whole-rock chemistry of the sample.

Jan 1, 2009

By Yousef Ghorbani, Abolfazl Danesh, Fatemeh Kazemi, Ataallah Bahrami, Morteza Abdollahi, Mohammad Raouf Hosseini

This study aims to investigate the effects of operational variables on concentrate grade, recovery, separation efficiency, and kinetic parameters of the copper flotation process. For this purpose, the effects of the pulp solids content, collector and frother dosage, and preparation and concentrate collection time were studied using a Taguchi experimental design. The results of statistical analyses indicated that the concentrate collection time and pulp density were the most influential parameters on concentrate grade. Considering copper recovery, concentrate collection time, collector dosage, and pulp density were the most significant variables, in decreasing order of importance. Also, the separation efficiency was mostly influenced by the concentrate collection time. Furthermore, kinetic studies showed that the second-order rectangular distribution model perfectly matched the experimental flotation data. The highest kinetic constant of 0.0756 s−1 was obtained from the test, which was performed with 35% solids content and 40 and 20 g/t collector and frother, respectively. The highest predicted copper recovery of 99.57% was obtained from the test at 30% solids content, and the collector and frother dosages of 40 and 15 g/t, respectively

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

By M. Mankosa, G. Taylor, G. Luttrell, J. Yasalonis

Several industrial-scale HydroFloat separators have recently been installed at Mosaic’s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale, and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The apparent benefits, theory of operation, and commissioning of the equipment are also discussed.

Jan 1, 2007

By D. L. Moellenberg

Under various state laws enacted mostly within the last 20 years, reclamation requirements and standards for hard-rock mining operations have been established virtually everywhere in the western United States. Unlike the uniform and detailed coal mine reclamation requirements under the federal Surface Mining Control and Reclamation Act ( "SMCRA" ) and state programs mode led after SMCRA, the various state law hard-rock mine reclamation requirements are based upon a variety of objectives, and therefore are subject to varying standards from state to state. While the diversity of reclamation requirements complicates the determination of what reclamation measures will be required at any particular mine, there are valid reasons for this diversity. There are dozens of different commodities mined in the United States, and mining methods are different for each commodity. Local natural conditions such as climate, precipitation, geology, hydrology, and biology vary widely across the county. Site-specific conditions also affect mining and reclamation methods. Also, factors such as economics, land use, and environmental protection issues receive different priorities in different states and communities within those states. State reclamation requirements in general provide the flexibility to consider site-specific circumstances, allowing operators to design and engineer the best reclamation measures for each mining site. To the mine developer or manager, reclamation requirements must be translated into design, operational, and closure measures for mine planning. Each of these measures must then be assigned additional costs to be factored into the economic decisions for a particular mining operation. On a broader level, reclamation costs must be factored into decisions such as where to invest in exploration and mine development. The purpose of this paper is to provide a summary of the state non-coal mine reclamation requirements in twelve western states. This summary comparison may be useful as a starting point in considering how local reclamation requirements will impact potential mining costs.

Jan 1, 1994

By Greg Wieland

Deep sewer tunnels are required to meet future growth demands of the City of Austin?s down-town redevelopment. The tunnel is 18,000 ft long and varies in finished diameter from 54 inches to 96 inches. The tunnel crosses under Austin?s Town Lake three times and there are four main work shaft sites. Geology, groundwater, foundations, downtown redevelopment, and an active, healthy community put significant constraints on the design. This paper discusses a major underground project for downtown Austin and discusses the risk considerations and the opportunities the design team took toward optimizing the project design for the construction phase.

Jan 1, 2008

By Donald Hulse

"Mining has been a source of controversy for at least 500 years. “Since there has always been the greatest disagreement amongst men concerning metals and mining, some praising, others utterly condemning them…” (Agricola, 1556). In 2016, it is widely recognized that mineral resources and reserves must give due regard to the social license in order to operate.“Most commonly, the social license to operate (SLO) is understood to refer to ‘the ongoing acceptance and approval of a [project] by local community members and other stakeholders that can affect its profitability’ (Moffat, 2014).” “Social License to Operate has gained traction, in part, because it is also a concept which – while remaining poorly, technically defined – is generally easily and widely understood by community stakeholders (Bice, 2014).”A generation ago we learned that mining is based on a stable platform supported by three pillars, geology, mining and metallurgy. The three-legged stool is a very stable structure (Fig. 1).In 2016, it seems that we have added some other legs to the stool (Fig 2). The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC Code) addresses “social, and governmental factors…” (JORC 2012), and refers specifically to social license in Section 4 of the Report Template “Estimation and Reporting of Ore Reserves.”The Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Guidelines refer to “environmental, legal and social data…(CIM 2003).”Compared to these, the 2014 SME Guide is positively verbose stating “a discussion of any potential social or community related requirements and plans for the project and the status of any negotiations or agreements with local communities,” (SME 2014) although in all cases the scope of this disclosure is left at the discretion of the competent person.When there are more than three legs on the stool, it is imperative that all legs be constructed exactly to the design. Any one or more legs that are out of alignment will cause the stool to wobble.Engineers are trained to create designs to meet specifications. Loads can be estimated, forces calculated and cost studies completed that will lead to, not only a stable design, but the most efficient design that meets the specifications."

Jan 1, 2015

By Shaoxian Song, Ling Xia, Hongqiang Li, Yubiao Li, Yunliang Zhao, Shaobing Xie

Since human daily demands for fresh water have been increased significantly, the supply of fresh water for the mining industry, especially froth flotation, should be considerably reduced. In addition, stricter environmental standards have been implemented in many countries to reduce the risks due to the disposal of wastewater, many flotation operators have to seek more efficient ways to utilize the limited fresh water sources. Recycling water with high concentrations of impurities is a normal strategy for most of the mineral processing plants; however, water quality should be carefully considered to guarantee a smooth flotation process. Recently, the application of seawater in flotation has attracted much attention due to its availability and abundance rather than fresh water. However, the influencing mechanisms due to the application of seawater in flotation have not been fully understood especially the reactions between mineral particles and bubbles in the presence of high concentrations of cations and anions. This would impede the application of alternatives to fresh water in the flotation. Therefore, this paper reviews the current water sources and the technologies for water recycling in the flotation process. Specifically, the life cycle of water in flotation was proposed. In addition, the strategies including high pulp density flotation as well as the most promising alternatives to fresh water have been discussed in details, with the related mechanisms being demonstrated.

By M. Dobbins

The advent of the more efficient and effective rare-earth roll (RER) separator in the early 1980?s began a new era of dry magnetic separation. The RER units quickly became the separator of choice within the materials processing industry. Though RER separators are now commonplace throughout the world, only modest advancements have been made to the original design. This paper details recent, more significant, rare-earth magnetic separation developments. These developments maintain the best features of existing technology while minimizing shortcomings. The discussion includes discerning features that aid in better metallurgical performance. Also discussed are improved mechanical aspects that allow for both easier operation and maintenance. Performance details from various test programs are included.

Jan 1, 2009

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a roomand-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90%. But, the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing oversprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99% and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber.

Oil sands processing generates huge volumes of slurry, known as tailings, that is being stored in tailings ponds. The volume of produced tailings is a very important factor in oil sands surface mine planning, because the available area for dam construction is limited to the lease areas. On the other hand, oil sands operators cannot leave mine sites without reclaiming the tailings ponds. Since most of the reclamation material is generated in either oil sands mining or processing, it is reasonable to include reclamation material requirement as part of long-term mine planning. In this paper, an integrated optimization framework is proposed to maximize the net present value (NPV) of the produced oil sands, with respect to tailings capacity constraints and reclamation material requirements. A mixed integer linear programming (MILP) model is developed to find the optimal solution for long-term mine planning problem. A sample bitumen processing flow sheet is used to formulate the volume of produced tailings, based on Clark hot water extraction method. To verify the proposed model, it is coded in Matlab and run using CPLEX. Run results for real-case oil sands dataset show that the optimal production schedule meets material requirements for reclamation, tailings volume is within tailings capacity range in all periods and the production schedule follows the predetermined horizontal direction.

Feb 27, 2013

By Wayne E. Kilker, Michael J. McBride, William P. Levy, Thomas J. Lamb

Between 1989 and 2004 the Massachusetts Water Resources Authority (MWRA)constructed several major wastewater and water tunnels associated with three major projects in the Boston area of eastern Massachusetts. There were many similarities and differences in the bedrock conditions encountered and among the contractual approaches for these independent projects. Through a clarification of the approach similarities and analysis of the contract differences, this paper addresses and presents what are considered to be valuable lessons learned. In doing so, the paper follows the evolution of such disparate issues as contract conditions, baseline reports and dispute review boards. The authors believe that the lessons learned even represent what, in certain cases, could be referred to as “universal truths” that are intended to have application to the next generation of tunneling contracts.

Jan 1, 2005