Search Documents

By John Bley

White Pine Copper Company operates a mine in the Upper Peninsula of Michigan using a modified room-and-pillar system for extracting ore.1 Mine production averages 15, 500 tons per day. The terrain is predominantly level and the depth of cover varies from 500 to 800 feet over the present workings with depth increasing as mining progresses down the dip. The deposit is situated on a low angle plunging, anticlinal structure composed of sedimentary beds. Local terminology for the stratigraphic units which contain the ore horizons, named in ascending order, is as follows: lower sandstone, parting shale, upper sandstone and upper shale. The ore zones of copper enrichment are, contained in the parting and upper shales. The parting shale will vary; from 6. 5 to 9.0 feet thick; the upper sandstone from 2 to 10 feet; and the upper shale from 1. 5 to 6. 5 feet. Two variation of the room-and-pillar system are used to extract the ore depending on grade and local ground conditions. One system is called the parting shale method and recovers the parting shale only. This system requires a mining height of 8 1/2 feet to accommodate large-scale, high-capacity equipment and this working height is obtained by removing approximately 1 to 2 feet of the barren lower sandstone with the ore. Under the second system, locally termed full column, the mining height is about 14-1/2 feet and this system removes the parting shale, the upper sandstone and the lower mineralized zone, approximately 1-1/2 feet, of the upper shale at which point it is possible to maintain a competent back (Fig. 1).1

Jan 1, 1964

By D. R. Barker

The economic performance and competitiveness of a concentrator are dependent on the production of accurate real-time assay information and the manner in which it is utilized. Our paper describes the relative merits of on-and in-stream analysis techniques and the economic significance of Assay-Based control and Target Oriented Display Systems. At Outokumpu's pyhasalmi Concentrator, a Flotation Expert Display System aids the process operator to make better decisions and provides guidance on the most efficient method of achieving the desired control objectives.

Jan 1, 1989

By S. R. Wardwell, M. J. Robison

INTRODUCTION The first phase of the Los Angeles Metro Rail Project consists of 7.1 km of subway and stations running through downtown Los Angeles from Union Station to MacArthur Park. Contract A146, Tunnels from 5th/HILL Station to 7th/Flower Station, involves tunnel construction through the heart of downtown Los Angeles. The alignment of the tunnels passes beneath twelve buildings, ranging from a 3-story below grade parking structure to numerous 12 to 14 story buildings. The soil along the alignment is alluvium, consisting of silts and clays, clean sands and gravels located above the ground water table. Because of unstable ground conditions, which led to excessive ground losses in several instances, and because of the potential for excessive building settlements, it became necessary to design and perform a program of chemical grouting. The chemical grouting program was designed such that tunneling could proceed on a one shift per day basis, with chemical grounting being performed on the remaining two shifts. Each day 21,000 to 31,000 liters of sodium silicate grout were injected through sleeveport grout pipes installed 18 m deep through the tunnel face. Tunnel advance rates of 12 m per day, 60 m per week, under full chemical grout cover were achieved. The chemical grouting program virtually eliminated both ground loss and settlement and permitted successful excavation of the tunnels. The purpose of this paper is to describe the chemical grouting program used to control ground losses and settlement on Los Angeles Metro Rail Contract A146. The paper begins with a description of

Jan 1, 1991

Room-and-pillar mining at White Pine started in 1953 from a sub-outcropping orebody that gently dips to 1000 m depths in a distance of about 6 km. High horizontal stresses were recognized in the mid-1960s which had obvious stability impacts when viewed in combination with the increased overburden stresses. Modifications in conventional room-and-pillar design were introduced through the years on a trial-and-error basis to help overcome stability and resource recovery problems. These modifications were based on pressure arch concepts using pillar yielding and/or pillar recovery, and on mine layout orientation to minimize stress impacts. While some of these modifications were successfully applied in some areas, they failed in others. Through the years, visual observations played a major role in panel design with contributions from stress measurements and analyses. However, the down slide in the copper economy during the 1970s and early 1980s resulted in a loss of interest in the application of these concepts. This paper reviews ground control problems and presents the results of recent stress measurements and computer analyses. They shed light on the importance of using yield pillars and mine layout orientation to control stresses at depth.

Jan 1, 1993

By Sean Warren, JOSEF BOURGEOIS

The potential of rockfall at open-pit mines presents a continuous hazard to mine workers and is typically mitigated by designing catch benches at empirically determined widths. The National Institute for Occupational Safety and Health (NIOSH) is working in conjunction with industry and academia to revisit and update current catch bench guidelines to better match acceptable risk tolerances for modern mining practices. To begin this process, a rockfall testing program was designed to gather empirical runout and bench catchment data at partnering mine sites in the Western United States. This paper presents a detailed description of each component of the rockfall testing program, including scouting and safety plan development, equipment requirements, synthetic rock development for uniform testing across varying bench configurations, local rock collection for testing of mine-specific geology, data acquisition during testing, and data processing. Additionally, this paper describes how the program has been updated over time according to lessons learned during initial rockfall testing.

Feb 1, 2024

By R. J. Pugh

The surface chemical sites on several fillers (quartz, feldspar, calcite and granite) were studied by the adsorption of well defined acid and basic probe molecules (benzoic acid, benzyl alcohol, ethyl benzoate, pyridine and benzyl amine) from cyclohexane. The results provided a wide variation of adsorption data, emphasizing the extensive range of site heterogeneity on the filler surfaces. In addition, it was shown that the acidic probes were strongly adsorbed on all of the minerals, thus indicating that the basic surface sites dominate the acidic ones. Also, through FTIR studies with vapor-phase probes adsorbed on orthoclase, it was possible to identify the nature of specific sites and the type of bonding occurring between the filler surface and the probe molecule. These types of surface analytical techniques could give useful information for predicting the adsorption functional groups on dispersants, dyes, thickeners, etc. and could lead to enhanced interfacial bonding between the filler and the matrix.

Jan 1, 1993

By R. R. Klimpel

During the period of 1973-79, an extensive period of research and development was undertaken by Klimpel and coworkers (1980, 1981, 1982a, 1982b, 1983. 1984, 1987) on the identification of a commercially viable chemically assisted approach to improving the efficiency of the wet grinding of coals and ores in tumbling media mills. The emphasis of the previous publications just listed was on the engineering use implications of controlling-slurry viscosity (rheology) in laboratory and plant scale grinding devices. In this paper, some discussion and results pertaining to the actual chemical screening phase will be presented.

Jan 1, 1988

By Karl O. Toppel, Jim Flaherty

The desire to minimize gaseous effluent in smelting and maximize gold yields from refractory ore are driving the nonferrous and gold refining industries to demand more and more oxygen. This, coupled with an increasingly competitive marketplace, forces the investigation of alternate methods of oxygen supply. Current progress in both the non-cryogenic and cryogenic fields is making the use of low-purity oxygen much more attractive. The benefits of on-site production are now available to most oxygen users. Historically, these on-site advantages could only be achieved by relatively large plants using high-purity cryogenic technology. The evolution of low-purity cryogenic and non­cryogenic oxygen production has added a new method of delivering on-site production. Specifically, the advent of oxygen Vacuum Swing Adsorption (VSA) technology has brought these benefits to smaller-volume customers by cost-effectively supplying oxygen requirements as low as 20 tons per day, (tpd). Low-purity cryogenic plants have also made an impact on the market, yielding cost reductions for larger-volume customers with oygen requirements greater than 70 tpd. This paper reviews the advantages and disadvantages of current supply methods for users having varying volume, purity and other requirements.

Jan 1, 1993

By J. Slivnik, A. Stergarsek

[The site] [Z]irovski vrh uranium ore deposit is located in the extreme north-western part of Yugoslavia, some fourthy kilometers from the capital of Socialist Republic of Slovenia, Ljubljana, not far from the Italian and Austrian border. The sandstone type deposit of uranium ore with medium grade is located in a foothill of Julian Alps. The site shows some typical conditions for this region, which demand special attention in respect to the incorporation of an uranium treatment facility into environment. Among these specific conditions the following site characteristics should be mentioned: - populated area of agricultural and recreational value, - unconvenient climatic conditions with excessive rainfall and long lasting temperature inversions in the winter time, - very pure surface and underground waters which supply the drinking water reservate for large area including the capital of Slovenia, - sharp relief, - unconvenient geological structure. The choise of technology The intention to produce uranium and at the same time respecting the natural characteristics and existing uses of the site made the design of the ore treatment facility relatively difficult one. In general, there were two basic alternatives available perform the task. First alternative was to adopt the usual technological flowsheet with wet tailings disposal and with discharge of used water i.e. liquid effluents into the river. In order to prevent the negative impact of such technology on the sourrounding area sophisticated water purification installation and costly measures in wet tailings disposal e.g. impermeabilisation of large areas by concrete injections, large dam constructions, uncertain capturing of the water sources should be employed. Second alternative was to modify the usual flowsheet by employing the maximal recycling of liquid effluents to the process and to dispose the solid

Jan 1, 1980

By Otis M. Clarke

The Eufaula bauxite-kaolin district in southeastern Alabama is an important source of raw material for the refractory industries in the United States. At the present time, five companies are mining and processing bauxite and kaolin from this district and a sixth company is holding substantial reserves. Mining operations are expanding, but finding new ore reserves is a major problem. The Geological Survey of Alabama sponsored geologic research in the Eufaula district to: 1) investigate the utilization of sandy kaolinS and other clays associated with bauxite-kaolin deposits; 2) find limits of the bauxite district, looking for possible extensions; and 3) study the geology of the district, looking for patterns or trends that may aid in finding new ore reserves. This work was done with the full cooperation of mining companies operating in the district and property owners. Research was aided by the U.S. Bureau of Mines and the University of Alabama. The investigation included detailed geologic mapping of mines, drilling in selected areas, and making mineral analyses of bauxite and clays. The mapping was performed primarily by pace and compass because of the complexity of the deposits studied, but aerial photographs were used to a limited extent. Drilling included both auger and core drilling. The auger drilling was limited to 100 feet, but core holes were drilled as deep as 200 feet. The term 'bauxite,' as used here, indicates a mixture of minerals containing more than 50 percent gibbsite. Bauxitic clay is a mixture of gibbsite and kaolinite that contains more kaolinite than gibbsite. The term "kaolin" indicates a clay composed of predominantly kaolinite. Other clays in the Eufaula district are composed of kaolinite, illite, quartz, mica, and goethite or hematite.

Jan 1, 1971

By J. F. T. Agapito

Two flat-lying trona seams 3-to 3.5-m thick, approximately 10 m apart, and at depths of 250 m are mined by room-and-pillar at OCI's Big Island Mine in Wyoming. Continuous miners and a yielding pillar system have contributed to improvements in resource recovery and productivity. Long-term stability with minimal subsidence is needed for a large portion of the mine beneath the Green River channel. This was investigated by computer modeling in 1990. Although results of the study indicated good long-term stability, recommendations were made for stress determinations to verify the model. Stress determinations made in 1997 showed pillar stresses 10% to 20% higher than the model stresses, and barrier pillar stresses 10% to 15% lower. This implies that higher panel stresses will be transmitted from the upper to the lower seam. A stability evaluation of the lower seam is planned before two-seam mining to assess entry widths and support requirements.

Jan 1, 1999

By Douglas R. Cook

The Ertsberg East discovery was announced by Freeport in 1979 with proven geological reserves of 45 Mt (49.6 million tons) with a grade of 2.65% copper and recoverable gold values. This recently discovered deposit is one of a cluster of skarn-type copper occurrences found within the limits of Freeport Indonesia's mining con- cession at an elevation of about 3600 m (12,000 ft) in the extremely rugged Jaya Wijaya Mountains of Irian Jaya, the Indonesian half of the island of New Guinea. The Ertsberg East lies about 1.5 km (0.9 miles) east of the Ertsberg ore body, which is also known by the Indonesian name "Gunung Bijih" or "ore mountain." For general background, the original Ertsberg ore body was first discovered by the Dutch geologist Jacques Dozy in 1938 while on a mountain climbing expedition. It was mapped and sampled by Forbes Wilson and Del Flint after a two-week harrowing trek into the mountains from the coastal swamps. A drilling program in 1967- 1968 established that the Ertsberg was a viable mining venture, containing approximately 33 Mt (36.4 million tons) of skarn-type copper ore. The deposit averaged 2.5% copper, with significant values in gold and silver. The first shipment of copper concentrates was made in December 1972, following a capital investment of $200 million. Following the routine production of ore from this deposit, it became necessary to consider additional sources of ore to extend the life of the mining operation. An exploration program was thus started with the initial objective of finding shallow or surface ores which could be blended with the material being mined at Ertsberg. Project geologist Frank Nelson was transferred from Freeport Exploration Co. to the Freeport Indonesia organization at the Ertsberg mine. However, the exploration work was the functional responsibility of Freeport Exploration. Del Flint had overall responsibility for the program from the Reno headquarters office and provided liaison with management in the USA and Indonesia.

Jan 1, 1991

By E. J. Sullivan

This study seeks to define the mechanism of oxyanion sorption onto surfactant-modified zeolites. Zeolites which have been treated with hexadecyltrimethylammonium bromide (HDTMA) surfactant to produce a hydrophobic surface are capable of sorbing both organic compounds as well as oxyanions such as chromate, selenate, and sulfate. Simple ion exchange and charge-balancing mechanisms do not fully explain this unusual phenomenon. The sorption of HDTMA surfactant appears to be partly ion exchange and partly sorption to non-ion-exchangeable sites. Sorption of chromate is a simple exchange mechanism with bromide, which co-adsorbs with HDTMA to form a surface precipitate. Information from this study will be used to design on-site and in situ treatment systems for contaminated water, such as filter beds and permeable barriers.

Jan 1, 1995

By Chee Theng

"So many talks, so little time.One of the toughest challenges associated with attending the SME Annual Conference and Expo is deciding how to allocate one’s resources. After accounting for keynote and plenary sessions, committee meetings, networking events, luncheons and exhibits, attending even one of the 109 technical sessions and more than 600 technical paper presentations can be a labor of love. Many, however, managed to make it to many of the sessions, including the mineral and metallurgical processing technical session on solvent extraction, ion exchange and electrowinning.At one point, that room was seated to near capacity, with a considerable number of the audience members standing by the walls at the back. Brittany Valera of Freeport-McMoRan Inc. was one who came early and enjoyed the session in its entirety. "Everything was pretty exciting," she said. "I really liked the modular plants. I think the future of mining, just like what we talked about in there, lies in thinking about things like remote locations, lifetimes of plants, anything that would be reusable and sustainable; and lower-cost and user-friendly would be really beneficial."Michael Moats, associate professor of metallurgical engineering at Missouri University of Science and Technology, started off the session by presenting on behalf of post-doctoral student Alex Luyima, who, like many before him, had been snapped up by industry and is now working for a secondary-metals refining company in Texas. Their team studied the nucleation and growth mechanism of copper on stainless steel from synthetic acidified copper sulfate in the absence and presence of chloride ions and three commercial organic additives: Hydrostar 4208, DXG-F7 and Cyquest N-900. Currenttime data were analyzed using known models, with reference to scanning electron microscope images. Good agreement was achieved between the models and SEM micrographs of deposits at a commercially relevant current density of 30 mA/ cm2. The addition of 20 mg/L chloride was found to increase the size and reduce the number of nuclei. The addition of 2.5 mg/L of each additive did not change the mechanism, but all three reduced the size and increased the number of nuclei, leading to more uniform coverage of the substrate with smoother deposits produced in twohour electrowinning experiments. N-900 had the best deposition coverage while DXG-7 was the easiest to dissolve."

Jan 1, 2014

By V. G. Lofftus

Since plant start-up in January 1983, Golden Sunlight Mines, Inc. has implemented several process changes and improvements. Among these are a pulp preaeration circuit and a sand tailings retreatment circuit. The purpose of the preaeration circuit is to reduce reagent consumption during gold dissolution. The sand tailings retreatment circuit was added to recover and process separately pyrite concentrate to maintain acceptable overall gold recoveries with the more refractory sulfide ores. Research and plant operating data along with process and improvement descriptions are presented.

Jan 1, 1987

By Harry M. Castrantas

Caro's acid (peroxymonosulfuric acid-H2SO5) is used to destroy cyanides in tailings slurries due to its rapid reaction and low capital and operating costs. Due to its instability, Caro's acid is generated at the mine site using a hot or cold process. The majority of gold mines that use Caro's acid use the FMC hot process. In the FMC hot process, it is not necessary to cool the Caro's acid to minimize decomposition since it is used immediately upon generation. In contrast, the cold process uses a chiller to cool the raw materials and product. This paper will show, using laboratory and field data, that there is virtually no difference in Caro's acid yield between the cold and the FMC hot processes. Caro's acid yield depends on the mole ratio and concentration of sulfuric acid and hydrogen peroxide and is independent of operating temperature.

Jan 1, 1997

By A. Bruynesteyn

The results of leaching experiments in columns simulating 80 and 200 ft deep cores through a leach dump are discussed, By equipping the columns with can precipitation plants, actual plant conditions could be duplicated. The results produced a better understanding of the physical and chemical limitations of the leaching process.

Jan 1, 1975

By W. S. Fyfe, R. J. Puddephatt, S. Zhou

Gold is easily mobilized at temperatures within range 600-11OO°C by gases such as Cl2, CO, H2S, in gas mixtures, at low pressures. Such gases are relevant to conditions of granulite facies metaomorphism in environments of magma underplating. These observations suggest an efficient mechanism for moving gold to the upper crust during major thermal events. The efficiency of precipitation of gold at lower temperatures is related to available mineral surfaces and pyrite appears to be an excellent substrate for gold precipitation.

Jan 1, 1989

By Edmund W. Murphy

At the first workshop on Surface Subsidence Due to Underground Mining (1 981 ) , Yarbrough delivered a paper (1 ) describing the mine subsidence insurance program in Illinois operated as the Illinois Mine Subsidence Insurance Fund (IMSIF) . In this paper we will present claims data and describe changes that have occurred in the Illinois Insurance Code during the first six years the IMSIF has been in existence. The change in the original Illinois Public Act 80-1 41 3 that most affected the public was an amendment increasing the maximum amount of mine subsidence insurance avail- able on a structure from $50,000 to $100,000. Seventy-two counties in Illinois have been undermined for minerals, primarily bituminous coal. In Franklin County (.in the southern part of the state) 36 percent of the land area has been undermined for coal extraction. In St. Clair and Madison Counties , two counties that include the St. Louis Metropolitan area along the western border of the state, 10 percent and 7 percent of the land surface have been undermined. Most of the undermined area in the two counties is beneath urbanized land. In 34 counties, approximately 1 percent or more of the land surface has been undermined (2). The first shaft mine in Illinois was sunk in the city of Belleville (east of St. Louis) in 1842, and the mines of early vintage have initiated the majority of the mine subsidence claims. Data compiled from the first six years reveals that most Illinois mine subsidence events that affect structures occur over abandoned mines where early methods of high- extraction mining practices were used. Maps of these mines operated in the 1800s reveal irregular development of room and pillar areas and poorly defined production areas (panels). Rooms in the mines varied from 15 to 40 feet in width and the pillars varied in width from 5 to 40 feet. The pillars were often long and narrow. Recovery rates in mines that operated prior to 1900 generally averaged 50 per- cent, and extraction rates as high as 80 percent have been documented (2). Some pillar robbing occurred.

Jan 1, 1986

By Dennis C. Drehmel

Because of their relatively low cost, carbonate rocks are desirable in abatement of air pollution by acid gases. Although many processes and types of equipment have been proposed to control or prevent the emission of acid gases, this paper considers only three: dry-limestone injection, wet-limestone scrubbing, and chemically active fluid beds. For the dry-limestone-injection process, surface area-especially from pores in the 0. 2- to 0.3-micron range-is one of the important parameters which will discriminate between less and more reactive carbonate rocks. Marls, chalks, oolitic calcites, and other fine- grained limestones show larger-than-average surface areas and better- than-average removal efficiencies. Inert chemical impurities such as silica detract from reactivity. A dolomite is not necessarily less re- active than a calcite. For the wet-limestone-scrubbing process, dissolution rate of the carbonate rock controls the differences in stone reactivity. In this process the dolomites are less reactive than the calcites. In addition, more than 90 percent of the dolomitic impurity in Fredonia white lime- stone is inert during limestone scrubbing. Dissolution rate is also a function of particle size for large-grained carbonate rocks. Fine grinding of such rocks will increase the dissolution rate to that of a fine-grained rock. Hence the requirement of high dissolution rates may be met by some grinding of fine-grained material (e. g., marl, chalk, or other limestone) or by fine grinding of coarser grained material. For chemically active fluid beds, chalks have the best capacity to absorb both SO2 and H2S. However, most chalks are probably unsuitable for fluid beds because of high attrition rates. Because dolomites are generally more reactive than calcites with both SO2 and H2S, a dolomite would be the feed material of choice for a chemically active fluid bed.

Jan 1, 1974