Search Documents

By B. L. Bobo

To ensure the continued growth and economic viability of the Western coal industry, both in the domestic and inter- national markets, it is essential for the industry to become more creative and active in confronting the most serious obstacle in this objective; and that is, the inherently long distances which Western coal must be transported inland to reach its major markets. Figure 1 shows the 1982 coal consumption by state for those states where Western coal was consumed. (Except as noted in this paper, Western coal producing states are defined as Colorado, New Mexico, Arizona, Utah, Wyoming, Montana and North Dakota. Any exceptions used will have only an insignificant effect on the content of the paper). This figure illustrates the long distances that are required for Western coal to reach its markets. The total production for 1982 from the Western coal producing states was approximately 220 million tons, of which only 85 million tons was consumed within the boundaries of these states. The remainder was transported to markets outside the area. This map also shows, based strictly on the consumption of the states to which Western coal was shipped during 1982 and not considering other factors which are involved in the marketing of coal, the total market potential of Western coal would amount to a total of 445 million tons. This does not include export coal from the West Coast, which is now estimated to be less than 2 million tons for 1983. In 1980, it had been estimated that by 1985 the West Coast exports would have been at least 10 million tons per year, which will not be attained.

Jan 1, 1983

By Thomas Fiest, Helmut Wannenmacher, Wulf Schubert, Manuel Entfellner

Mining and tunneling in so-called “squeezing ground conditions” at high in-situ stress can result in substantial and enduring ground deformations. The magnitude of deformations is closely tied to the applied excavation- and support concept, though typically, they can reach tens of centimeters. The yielding principle is based on the idea, that the need for support capacity decreases as deformation increases. To enable controlled ground deformation and safe working conditions, yielding elements as a part of the shotcrete lining are implemented. These types of elements avoid an overstressing of the shotcrete lining. During the deformation process, the support pressure of the yielding elements and lining increases, thus stabilizing the ground. Furthermore, long-term creep deformations of the rock mass can be absorbed with such a system. This economic support technique represents the state-of-the-art infrastructure tunneling practice in squeezing ground condition. A novel yielding element of High-Strength Expanded Polystyrene (HS-EPS) was invented, which overcomes existing systems’ drawbacks. This innovative system is lightweight and allows for safe and rapid installation. Furthermore, the modular setup of the element enables an easy on-site adaption to react to in-situ deformation patterns and changing ground conditions. Recent experiences from applications in Alpine base tunnels in squeezing ground are presented.

Jun 25, 2024

By M. P. Neira

In-situ leaching of copper from chalcocite relies on ferric iron concentration in the lixiviant being reduced to ferrous. To re-establish the ferric concentration in solution, ferrous must be re-oxidized. This reaction is slow under normal chemical conditions but it is catalyzed by Thiobacillus ferrooxidans bacteria. BHP Copper's Miami In-situ unit developed a bio-reactor as a method of oxidizing ferrous to ferric. The effects on oxidation of temperature, CO2? oxygen, and air injection flowrate were defined. This paper summarizes the results of ferrous bio-oxidation using plastic column packing and oxide ores as bio-reactors and the leaching results of the bio-reacted lixiviant on chalcocite ores.

Jan 1, 1997

By R. K. Agarwal

In this paper a simple three-layered medium is considered. A circular hole is centrally located in the intermediate layer. The layered sheet is loaded uniaxially perpendicular to the stratification. The Young's modulus of the intermediate layer is lower than that of the outer layers. The stress distribution around the circular hole in a stratified medium is significantly different when compared to the case of a continuous homogeneous medium. The distribution depends upon the ratio of the height of [the] intermediate layer and [the] hole diameter. A comparison of stress the distribution and procedures for preparation and testing of [the] model are given. The potential of the technique is outlined.

Jan 1, 1968

By A. K. Bakshi

Mineral suspensions show Newtonian flow properties at lower solid concentration, but change into non-Newtonian regime as the solids content is increased. For Newtonian fluids viscosity is independent of shear rate, but for non-Newtonian fluids it varies with rate of shear. Therefore, measurement of viscosity at a shear rate, different from the process will be futile unless the slurry is Newtonian. This is especially true for hydrocyclone operation, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between viscosity and process efficiency. A new technique to distinguish such changes in flow type has been developed. This involved a co-axial cylinder type viscometer which measured apparent viscosity at a low shear rate, and a vibrating sphere type viscometer which measured the apparent viscosity at a high shear rate. Special precautions were taken to allow measurements of viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica of 80% passing 65~m size in water was used to prepare slurries at concentrations ranging from 1O-70wt% solids. Viscosity of each slurry sample was measured simultaneously by both the viscometers and the results were compared with each other. With this technique, it was found that all the silica slurry samples were in the Newtonian flow regime.

Jan 1, 1995

By David S. Bolin, Gary R. Peterson

INTRODUCTION In both the United States and Canada, a company making a public offering of securities must comply with regulations which have been promulgated by Federal and/or Provincial Legislatures. This paper focuses on the regulations pertaining to reserve reports required by the United States Securities and Exchange Commission (SEC). SEC RESERVE FILINGS Reserve reports made to the United States Securities and Exchange Commission are the only reserve reports which are directly regulated by the United States government. The requirements for SEC reserve reports are set forth in the filing forms as shown in Appendix A, from Item 17A of SEC Form S-18. These reporting requirements, which are intended to protect the investing public from inaccurate or misleading claims, are primarily oriented to S-1 or other filings for new stock issues but must also be followed for annual 10K reports which must be filed annually by U.S. public corporations as part of the Corporate Annual Report. These undertakings require independent audits of reserves, mine designs, plant facilities and a general economic evaluation of the planned or existing operation as part of the backup documents for filing. An ore reserve is defined by the SEC as "That part of a mineral deposit which could be economically and legally extracted or produced at the time of the reserve determination". This definition is unchanged since it was last

Jan 1, 1988

By I. Chatterjee

The application of microwaves has a demonstrated potential for the ultimate removal of water from fine coal. The principle of microwave drying of fine coal is based on the selective absorption of microwaves by water. Coal is a poor absorber of microwaves. As a result, water can be removed from fine coal by selectively heating water molecules. One of the difficult problems drilling microwave heating is the exact determination of temperature in the core of the materials. The electromagnetic energy absorption in coal/water mixtures during microwave drying is controlled by several factors including the dielectric properties of the constituents. In this paper the dielectric properties of various ranks of coal are presented as a function of frequency and moisture content. The measured dielectric data are incorporated into electromagnetic and thermal models of coal which predict the energy absorption and temperature distribution during microwave heating.

Jan 1, 1990

Strainburst phenomena, generally characterized by a sudden release of energy in a volume of highly stressed rock, are often encountered in such situations like crown pillar bursts in cut-and-fill mining, face bursts at development headings and floor bursts in deep shaft sinking. This paper describes a simple FE modeling approach which leads to the calculation of the energy release rate (ERR) and the total energy storage rate (TESR) in the rock mass around the openings. The merits of using such energy parameters in the analysis of strainburst problems to identify areas of high energy release/storage are discussed. However, much site-specific back analyses are needed to better understand how strainbursts and energy parameters are inter-related.

Jan 1, 1998

By J. A. Cole

Santa Fe Pacific Gold's Lone Tree mine is located in Humboldt County, NV, 45 km (28 miles) east of Winnemucca. The mine currently operates a 1.74-Mt/a (1.92-million stpy) run-of-mine heap-leach operation and a 2.27-kt/d (2500 stpd) refractory gold¬ore-processing plant. Most of the mill-grade ore reserves are refractory, mainly due to pyrite and arsenopyrite encapsulation of the gold. The autoclave pressure-oxidation circuit was commissioned in February 1994 to process the refractory ore. Mineralogy unique to the Lone Tree deposit allowed for the design of a partial-oxidation process. It takes advantage of the heterogeneous nature of the pyrite morphology. Partial oxidation has resulted in an autoclave plant that is able to achieve low operating-unit costs (Figs. 1 and 2).

Jan 1, 1995

By Adrian C. Dorenfeld

The lesser developed countries (LDC's) may be classified into two categories: 1) oil producers, and 2) non-oil producers. The non-oil producing LDC's, as a class, are at present in very difficult financial straits. (1) Since the quadrupling of world market crude oil prices in 1972, an ever greater share of the LDC's export earnings have gone to pay for oil imports, in-stead of national reinvestment. The LDC's inter-national debts--much of it to pay for oil--have soared to record levels, with consequent limits for future credits. (1) Again, this inhibits future national investments, and there does not seem to be an end to the future increase of Organization of Petroleum Exporting Countries (OPEC) prices. Indeed, some of the economic difficulties in some metal markets--particularly the imbalance of production vs. markets for copper, can be traced indirectly to the OPEC cartels' heavy-handed impact on copper producing LDC's which must produce copper at any price to meet their oil bills. (2) Among the major oil importing LDC's are the Philippines and South Korea. 50th nations have substantial cement industries. The South Korean industry is geared for major export markets in the Far East. Both nations have ambitious plans for economic growth in order to accommodate burgeoning populations with ever increasing expectations for high standards of living. These plans had some success, more or less, until the high OPEC oil cartel charges had to be borne. Now, in common with all oil-deficit areas, the Philippines and South Korea are seeking lower cost sources of energy. Both countries have coal deposits. In the case of the Philippines, the reserves are in scattered, relatively small deposits. Most of the coal deposits are faulted, folded and, in general present formidable production problems for limited reserves. Nonetheless production has been on the order of about 70,000 to 150,000 tons per year in the last 30 years. Prior productions (1920-1941) varied between 9,000 Co 150,000 tons per year. (13)

Jan 1, 1978

By Paul H. Muller

The configuration of remote seal DP cells for specific gravity measurement is described and the calculations for calibration are presented. The error induced by ambient temperature change is investigated as it relates to capillary dynamics and electronic considerations. Instrument specifications are discussed in the light of accuracy requirements and the calculation of error vs. ambient temperature is described.

Jan 1, 1984

By E. R. Bauer

The ground control aspects and occupational safety concerns of extended depth-of-cut mining are presented in this U.S. Bureau of Mines (USBM) report. The scope of extended cut use and typical face operations while extracting extended cuts is reported. A comparative review of roof fall fatalities and a statistical analysis of accidents and injuries for both extended and nonextended cut mining is included. The views and opinions on extended cutting from a series of interviews with mine workers in five states are summarized. In addition, some of the problems and safety concerns of this extraction system are mentioned.

Jan 1, 1995

By V. L. Jr. Davis, F. L. Stanley, P. J. Bethell

Fwe 3 m (10 ft) diameter Microcel™ flotation columns were installed at Clinchfield Coal Company's Middle Fork preparation facility in order to reduce product ash and increase recovery and plant capacity. The Middle Fork facility is utilized for the recovery of fine coal from a feed stream that consists primarily of 1 .5 mm x 0 material. The columns replaced conventional flotation cells for the treatment of the minus 150 pm fraction while spirals are used to upgrade the plus 150 pm material in the plant feed. The addition of the column flotation circuit resulted in an increase in plant capacity in excess of 20 percent while reducing the flotation product ash content by approximately 7 percentage points. Flotation circuit combustible recovery was increased by 17 percentage points. This paper discusses circuit design, commissioning, and sparging system design. Circuit instrumentation, level control, reagent system control, performance comparisons with conventional flotation, and general operating procedures are also discussed.

Jan 1, 1995

By M. L. Young

Hindered settling columns are used throughout the minerals industry for both size and density separations. In this study, the performance of a continuous, laboratory-scale hindered-settling column was evaluated for various particle systems. The test variables included solids composition, water rate, and column height column performance was evaluated using partition curves and corresponding performance parameters.

Jan 1, 1999

By O&apos

Southern Ohio Coal Company (SOCCO) and the U.S. Bureau of Mines have identified techniques to optimize the use of scrubbers on continuous miners. The techniques provide maximum respirable dust control while maintaining a high output. The use of radio remote control and scrubber help to achieve greater advance between lifts by locating the operator in fresh air during the mining cycle. He is also kept away from newly exposed roof, which is not supported. An alternative to fan-powered scrubber was also evaluated at SOCCO. A high-pressure water-powered scrubber system eliminated the noise associated with fans, and achieved an intrinsically safe system. Experience in the use of these scrubber systems and remote control at SOCCO are discussed.

Jan 1, 1990

By Claude M. Moreland

It is common practice when thermally drying coal from wet coal preparation facilities that the coarse +0.5mm fractions and fine fractions (-0.5mm) are combined and fed to a thermal dryer. There are very good reasons for this concept. The coal feed is much easier to handle in this condition for it is not as likely to stick inside the dryer or hang up in the material handling equipment, and is easier to feed and discharge. However, it is generally only the -0.5mm fines that really need to be dried. The +9.5m fraction of the cleaned coal will leave the dewatering screens, or drain and rinse screens, at an acceptable surface moisture, probably 5 or 5 ½ percent. The 9.5m x 0.5mm mesh fraction can be centrifuged to about 8 percent. The -0.5m fines can range from 18 to 22 percent or more, depending upon the type of equipment employed to dewater, and upon the size distribution within this size range.

Jan 1, 1982

By C. J. Kirkland

The paper describes the arrangements for the casting, curing and handling at the casting yard, of the concrete segments for the lining of the UK half of the tunnel, and the plant used for the handling of these linings at the construction site. An outline of the tunnel boring machines being used is given, with particular reference to lining handling and erection, and the extensive muck disposal systems installed. A general progress update will be given to the conference.

Jan 1, 1989

By Gerry Norton

The purpose of this paper is to make the most complete assessment of coal cleaning methods, both process and equipment related to modern-day production and environmental requirements. In order to achieve this primary objective, a number of interdependent aspects of coal cleaning technology require evaluation and analysis. 1.0 CLASSIFICATION OF SEPARATION PROCESSES Processes and cleaning equipment can be categorized according to the important parameters of 1) mechanics of separation, 2) size range application, 3) range or variance in accuracy of separation related to 2) above, and 4) feed-size ratio affecting 3) above.

Jan 1, 1977

By K Louie

When BHP Copper's Lower Kalamazoo Project commenced production in January 1997, two of the four original hoists had been converted to hoist ore from the Lower K level. Conversions on these hoists not only allowed hoisting from a much deeper level, but also created a higher hoisting efficiency and higher capacity as well. Conversions included new drums, new cables, SCR drives and other solid state control technologies not available when the original hoists were installed. Two of the original hoists were installed in the 1950's and the other two were installed in the 1970's.

Jan 1, 1998

By Roberto Pimentel de Souza

CURD started producing pellets in 1969, with one two-million ton straight grate plant. In the beginning of April '73, the second unit came on stream with an additional capacity of 3 million TPY of pellets. In January '77, the third unit started, bringing the annual capacity to 8 million TPY. For the present year 3 more units, 3 million each, are expected to begin production. CVRD's experience is given about the use of different binders and additives. Over the years several kinds of pellets have been produced to satisfy the market requirements. General quality information is given regarding each.

Jan 1, 1978