Search Documents

By Alvin W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall as mining showed oreshoots to be more continuous than drilling indicated. The Geophysics Department of Michigan Technological University developed a portable induced polarization drill hole probe with a 3 electrode configuration and a sampling radius of 5'± A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec. intervals and readings are taken every two feet. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the I.P. potential is sampled for 10 ms and recorded. Resistivity (ohm-feet) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous "S" values noted. The low resistivity amygdaloid contains sills of high resistivity basaltic trap. Verified by core logs, amygdaloid-trap contacts could be picked to ±.5' from resistivity alone. Lithologic logs of long steel holes, based' on resistivity, now replaced sludge logging. An "S" value of 30 mv/v was established as the lower limit of diagnostic I.P. effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found.

Jan 1, 1964

By E. R. Spencer, E. R. Bauer, G. P. Cole

Overexposure to hazardous noise has been found in most mining sectors, with up to 100% of the surveyed workforce experiencing a noise dose that exceeds the U.S. Mine Safety and Health Administration (MSHA) permissible exposure level (PEL). As a result, miners show elevated rates of hearing impairment of 70-90% by retirement age. To help manage noise exposures, the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software and implementation guide for use by mine management and safety personnel. This paper describes the development, functions and basic operation of the initial-release version of DOSES. A revised version is being developed to incorporate additional user-suggested functions, and its development and implementation to assess noise control solutions will be described in a future article. The software relies on a time-motion study that profiles the worker’s daily activities. Observations about the worker’s location and tasks or other activities are recorded along with the start and end time, to determine the duration of the tasks so they can later be matched up with the noise data. The software gives the user the option of assessing dose relative to the MSHA PEL, the action level or the NIOSH recommended exposure limit. The software generates a variety of interactive on-screen displays showing where, when and how the worker’s noise dose accumulated. It also can generate customizable printed reports. These outputs can be used to highlight the tasks, locations and times that are associated with the greatest amount of a worker’s noise exposure. DOSES simplifies and streamlines the record keeping and analysis associated with time-motion studies and worker noise exposures, so mine management can make engineering noise control or administrative control decisions to limit the noise overexposure of their workers.

Jan 1, 2011

By E. V. Kuzmin

The rock properties improvement means the exchange of natural properties: increase of stability, strain and compress tension, reduction of gas-liquid filtering property, increase Jung- module, other mechanical and physical parameters of rocks by injection the hardening materials, such as polymeric pitches, micro-or geocements by special technology under high pressure, to fill cracks. Flow of liquid materials between the rock units and hardening under high pressure create full redistribution of rock pressure in rock massif. There are many reasons to use this technology in underground mining, tunnelling, creation barrier technology in raioactive, chemical and other danger material site etc.

Jan 1, 1996

By Euclid P. Worden

In 1977, an article in World Mining (1) reported a total of 2726 rotary blast hole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher: Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item, to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to re¬ducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, five factors affect the rate of penetration. They are: 1. Bit selection 2. Weight on the bit 3. Rotary speed 4. Hole cleaning 5. Formation properties Of these factors, all but one may be control¬led by the operator. Looking at any one in detail may reveal possible improvements in the system. Cleaning the hole is a good place to start. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh, clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in re drilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole.

Jan 1, 1979

By J. R. Dillon

Today more than ever, there is an increased demand for higher plant production capacities and efficiencies to offset the increasing costs for labor and materials. Plants involved in processing large volumes of bulk materials are particularly interested in more efficient material handling systems to (1) reduce labor and maintenance costs, (2) improve blending of non-uniform raw material feed to processing facilities, (3) improve blending of finished bulk materials from storage. DragScraper systems are being used effectively for handling a variety of bulk materials in both indoor and outdoor storage. Materials being handled include ores, chemicals, coke, clay, and stone, to name a few. Handling capacities these machines can provide vary from a few tons to over 1500 tons per hour. The basic components of a DragScraper machine consist of a bottomless Crescent scraper, a two or three-drum DragScraper hoist assembly including gas, diesel, or electric power unit, operating cables, guide blocks, and either fixed or mobile head and tail structures. They are presently available in sizes through 15 cubic yards, for operating spans up to 1000 feet.

Jan 1, 1969

By H. Keith Henson

The purpose of this paper is to describe the possible application of two relatively new technologies: flat load cells, and improvement seeking computer programs (referred to in the literature as heuristic programs); to a very old problem, inventors control of ball mills. The combination of these two technologies seems most applicable to grate discharge mills operated closed circuit. It is possible that other applications such as controlling the inventory of autogeneous mills might also be found. Direct control of ball mill inventory has been the goal of a number of investigators over many years. Many patents and articles on the subject have claimed success, but operating installations are hard to locate. An excellent review of the advantages and problems of direct inventory control is contained in an article by Oswald and Ziegler (1). Figure 1 is a conventional representation of throughput vs. inventory with other factors such as slurry consistency and rock twee held constant. There are common sense, physical arguments? and experimental evidence supporting the existence of a unimodel curve of this twee? though direct measurement of the shape is difficult and how it moves as rock type changes is riot well known. Figure 2 represents the problem faced by all mass measurements of inventory, a tare weight of about 25 time the inventory mass. Worse yet, the tare is variable due to ball and liner wear and the Periodic addition of balls. The problem then breaks down into two parts: 1) obtaining enough mass

Jan 1, 1977

By Thomas Van Riper

Newmont Mining Corporation started as one man's investment vehicle. William Boyce Thompson, Newmont's founder, was already a millionaire many times when he incorporated his existing Newmont company in Delaware in 1921. The initial stake in the company was $8 million in capital contributed by Thompson and several close associates. In its infancy the company was truly a holding company. It did not operate or manage any properties. This situation changed drastically over time. By 1939 Newmont was actively mining 12 gold mines in North America. The following year, the first copper mine that Newmont ever managed directly, came into full production in South Africa. The period after World War I1 was a glorious one for Newmont. Plato Malozemoff took the helm of the company, and expanded its operations over the next 30 years into copper in Arizona, oil and gas in the U.S. and the North Sea, into domestic coal and thankfully, into significant gold operations.

Jan 1, 1989

By J. D. Forrester

In striving to develop this discussion about "Manpower for Industrial Mineral Industries" two fundamental classes of manpower are encountered. These are: 1) The Labor Force, comprised of unskilled and semi-skilled, nonprofessional personnel who participate in conducting economic, mineral deposit operations and; 2) The Professional People involved in the science, engineering, and management of such industrial enterprises. The commentary given here will be directed primarily to a review of the characteristics of the second or latter class. To pursue successfully a career as a scientist or engineer in today's industrial and social complex, it is necessary that technical knowledge must have been acquired by training and study in an institution of higher learning. Also, to act effectively, the individual must have achieved some degree of specialzation, although this element often is developed to most notable degree by post-graduate exposure and experience. In addition, and especially in the case of "management," it is desirable, indeed it is even necessary, that an individual recognize and appreciate the fundamental humanistic-sociological controls, and their nuances, as these elements exist to shape his total environment.

Jan 1, 1969

By John Mastoris, Kostis Dragasakis, Kostas Kouklidis, Shkurtë Gashi, Halil Berisha, Jenuz Bulica

Titan Group’s environmental policy and Sharrcem’s Corporate Social Responsibility (CSR) are the driving forces behind the development and implementation of a comprehensive Rehabilitation Plan at Dimce Quarry, which is the main raw material source for Sharrcem Cement Plant since the 1970’s, located in the municipality of Hani i Elezit in Kosovo. Based on an Environmental Impact Assessment Study and the approved Mining Plan and also on the principles prescribed in the Guidelines on Quarry Rehabilitation, released by the Cement Sustainability Initiative of the World Business Council for Sustainable Development (WBCSD-CSI), Sharrcem has adopted a quarry operation and rehabilitation process in line with the best practices in the mining and cement sector. This paper discusses the background for the development of the rehabilitation plan and the results of rehabilitation activities, as have been implemented over the last few years. The main objective of the progressive rehabilitation plan at Dimce Quarry is to restore the depleted pit and return it back to the original land owners for resettlement. To date approx. 3,4Ha of former mining area has been restored by backfilling and levelling of the depleted closed pit and returned back to owners, who have built their houses and turned it into a living area again. This Quarry has turned out to be a real composition and practical example of preserving and returning back the natural resources in a state compatible with the surrounding environment and with respect to the needs of the local stakeholders. The motivation for business to engage in rehabilitation activities in the first place lies in the belief that the development and implementation of a progressive and practical Quarry rehabilitation plan and restitution of the land will deliver significant environmental and social benefits that outweigh the long-term rehabilitation costs, while maintaining the company’s reputation.

Jan 1, 2017

By CADEN VITTI, Barbara J. Arnold

Mine tailings, the byproduct of mining and mineral processing, are increasingly mass-produced as a result of increased demand for metals and minerals as well as the advancement in technology that allows for the exploitation of lower-grade ores. Lower grades can increase the volume of tailings that may contain new gangue minerals that should be evaluated for the presence of critical minerals and other valuable metals. The practice of reprocessing, while relatively new, is crucial to reducing environmental damages, obtaining valuable critical minerals from waste, and contributing to more sustainable repurposing and disposal methods. With the increase in tailings dam failures in recent years, there is a large motivating factor in remining and removing the potential hazard to benefit the safety of potentially impacted communities. In analyzing the perspectives of various domestic and international studies, this literature review will determine the feasibility of reprocessing and reutilizing mine tailings waste for a more sustainable future while exploring current practices that have benefitted ecosystems and communities.

By Charles C. Mosher

An in-mine seismic technique for detecting faults has been tested in a Western U.S. coal mine. This technique has been used extensively in the U. K. to help guide longwall mining operations. Explosives detonated on the face of a seam generate sound waves which propagate into the seam. Reflections from faults are picked up by sensors on the same face. Computer processing is then used to determine the fault locations. A known fault was successfully located in this test. Modifications to the U. K. procedures were required for the relatively thicker roan and pillar mines common in the Western U. S.

Jan 1, 1983

By Mirza Muhammad Zaid, Nana A. Amoah, Ping Chang, Guang Xu, Ashish R. Kumar

The key takeaway of this study is the significant improvement in dust protection for roof bolter operators in underground coal mines. The optimized canopy air curtain (CAC), with a redesigned two-level manifold system, provides uniform airflow distribution that effectively reduces dust exposure. By enhancing the protection of operators from harmful respirable coal and silica dust, this technology can reduce the risk of diseases such as coal workers’ pneumoconiosis (CWP) and silicosis. The application of this optimized CAC design in real-life coal mining operations can dramatically improve worker health and safety by minimizing dust-related exposure, ensuring compliance with industry regulations and prolonging the lifespan of mining equipment by reducing dust accumulation.

Dec 1, 2024

By Thomas Pollard

It is truly remarkable how the image of longwall as a method of mining has changed. Between 1920 and 19609 viewed on a world wide basis, longwall was regarded as a' system for difficult and deep conditions and associated with intensive labour extraction. Today the world looks on longwall in the hope that it can produce the next really big break through in productivity, Three correlated machinery developments have made this possible, but it is not only the machinery developments, interesting though these be in themselves, but together with developments in control systems of these machines that longwall now looks so much more attractive, The machinery concerned is, of courses:- 1. The Anderton Shearer Loader - A miner that takes a narrow strip off the, face at rates acceptable to modern mining engineers. 2. An Armoured Flexible, Conveyor which can be kept in close contact with the face and still convey coal as it is snaked over to the faces 3. Powered support systems which can be mechanised and controlled with reliability at any distance from the individual support itself.

Jan 1, 1964

By Lloyd H. Yeager

Good morning gentlemen. I'm very pleased to be a part of this fine program for the Society of Mining Engineers. Gypsum, as many of you know, is one of the most unique minerals on earth. The very excellent presentations which you have just witnessed, revealed the geological aspects of gypsum operations. It is not our purpose this morning to pursue this subject further. Instead, we felt you would be interested in some of the uses of gypsum . . . and what the future holds for gypsum products. To help accomplish this, we're going to first show the Gypsum Association's new film, "Shape Of The Future. ' This short movie traces gypsum f ram mines and quarries to its ultimate destination in homes, schools, offices -- in virtually every type of construction. We think you'll be particularly interested in the description of gypsum's fire resistive nature.

Jan 1, 1965

By JIACHENG XIE, Juanli Li, Wenyong Du, Tao Cui, Mengyao Dong, Pengfei Huo

The study proposes a dynamic path planning method for mining equipment based on spatial kinematics and real-time correction of coal-rock state identification. The method integrates real geological data and equipment operation information to improve the autonomous cutting of fully mechanized mining equipment.

May 1, 2023

By R. J. Sweigard, T. Beckman, C. T. Justice, E. D. Thompson, T. C. Hopkins

As a means of permanent disposal, fine coal refuse is often pumped as a slurry into surface impoundments. As the available volume is filled, the embankment heights are frequently increased. The additional embankment material is often placed upon consolidated fine coal refuse. There has been concern about the long-term effect of consolidation of this material at or above the liquid limit on its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from central Appalachian coal-preparation plants. The refuse was consolidated in 3-m (10 ft) Plexiglas columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart, and triaxial tests were performed on both the consolidated and unconsolidated material for comparison of their shear-strength parameters.

Jan 1, 1998

By Thomas B. Borak, Keith J. Schiager, Janet A. Johnson

INTRODUCTION Several major factors introduce uncertainties into the assessment of radon progeny exposure to miners using time-weighted average radon progeny concentrations: uncertainty in the measurement of radon progeny concentrations in specific areas, assignment of an individual miner's time to those areas, variation in radon progeny concentration between measurements and potential human errors involved in calculating concentrations and handling data. The currently available grab-sampling methods for determining working level were analyzed to determine the magnitude of the uncertainty due to each of these factors. For all measurement methods studied, the variation in the airborne concentration with time in operational areas of a mine is the dominant factor in the uncertainty in determining annual radon progeny exposures for individual miners. Uncertainties relating to accuracy of the method and precision of measurement were found to contribute a significantly greater portion of the total uncertainty than human errors. Under normal conditions, if the technicians performing the measurements are conscientious and well trained, human error contributes little to the total uncertainty of the radon progeny exposure determination. The primary goal of radiation monitoring is the reduction of radiation exposure to the lowest reasonably achievable level below regulatory limits. Monitoring personnel in mines should be trained not only to obtain accurate estimates of miner radiation exposures but also to recognize and, when possible, to implement correction of situations which result in unnecessarily high radon progeny exposures. ESTIMATION OF UNCERTAINTY DUE TO HUMAN ERRORS Human errors affecting the assignment of annual radon progeny exposure to individual miners can be placed in two categories: those related to the measurement of radon progeny concentration in specific mine areas and those related to estimation of occupancy time for individual miners and transcribing data to permanent records. The former are specific for the measurement method used; the latter are common to all methods. Errors in Determination of Working Level All systems for determining radon progeny concentration require measurement of several parameters, which include volume of air sampled, count rate and decay time. These quantities and appropriate constants are used in a basic equation, specific to the system, which estimates working level. An unintentional random mistake in measurement of any one of these parameters or in the selection of proper constants will contribute to the uncertainty in the determination of working level. In our analysis of human error we separated each measurement method into a sequence of independent operations, with each step subject to operator error. For each operation we estimated the probability of occurrence and the consequence of errors to obtain a resulting uncertainty. Certain types of errors result in specific consequences. For example, we assumed that an error of 5 seconds in timing of a 5-minute sample results in a fractional error of 1/60 (1.7%). Other types of errors can result in a range of uncertainty. Transposing digits read from a scaler can produce errors ranging from near zero to approximately 60%. In these cases we calculated the statistical variance for the distribution of errors. We assigned the square root of the variance divided by the mean as the consequence factor for that type of error. This is essentially the same as a coefficient of variation. The product of the probability of occurrence and the consequence factor is the fractional uncertainty in the measurement due to that particular error. The total uncertainty due to human errors is calculated by taking the square root of the sum of the squares of the uncertainties generated by all manual operations. Uncertainties Due to Human Error for the Kusnetz Method One of the techniques most commonly used to estimate working level in U.S. uranium mines is the Kusnetz method. A generalized way to express the equation used to compute WL by this method is: WL = (Net Alpha Counts)/(V)(ST)(CT)(E)(K) where: V = sample flow rate in liters/min ST = sampling time in min CT = counting time in minutes E = absolute counting efficiency K = Kusnetz conversion factor (dis/min-L per WL), as a function of decay time in minutes. The example of human error analysis presented here is based on the Kusnetz procedure having a timing sequence of 5 minutes sampling time, 40 minute decay time, 2 minute counting time. During the sampling procedure a stop watch is used to determine the timing interval. We assume that it is common to make small timing errors of a few seconds, but larger timing errors occur infrequently. Errors greater than 30 seconds are considered to be essentially non-existent since we assume that the

Jan 1, 1981

By Scott G. Britton

Many times during the construction of a project, whether large or small, the engineer will become involved with management of the work and workforce. In some cases, mine management will turn over the direction and responsibility of doing the work to the engineer. Because of this, it is important to know some of the basic principles of human resource applications- among other management concerns. This chapter, therefore, looks at the fundamental principles of human resource management. Three broad discussions are presented to the reader. These are: (1) organization, communications, and responsibilities of management; (2) analysis of worker motivation; and (3) supervisory leadership. Each topic encompasses the current thinking for coal mining and mining management. Much of the information in this chapter comes from Practical Coal Mine Management, by this author and published by John Wiley & Sons, Inc., which discusses in depth many of the ideas presented here. Interested persons are directed to this text for more information on management skills.

Jan 1, 1983

By Charles S. Phillips

Kaiser Aluminum and Chemical Corp. (KACC) had been discharging spent bauxite-generally referred to as red mud-into the Mississippi River for almost 20 years when, in 1972, it agreed to store the waste solids on land. KACC decided to utilize a DREW system (decantation, drainage, and evaporation of water) where the spent bauxite is deposited in a large drying bed, surrounded by a 9-m-high levee. At the bottom of the bed, corrugated, perforated plastic pipe is encased in filter sand. The company built one DREW bed at Gramercy, LA, in 1973 and a second at Baton Rouge in 1974 using draglines, tractors, and rubber-tired scrapers. When a third bed was needed in 1977, the estimated construction cost using draglines was judged too high and KACC personnel began searching for a better, less expensive method for constructing the levee. A bucket-wheel excavator and conveyor system was selected and has proved to be less costly than more traditional earth-moving systems.

Jan 7, 1980

By Klaus Beckmann

Gentlemen : My object reads "Longwall Rapid Advance of Coal Mining in the Federal Republic of Germany". It is true that the percentage of coal obtained in your country from longwall faces, with at present 1.2, is still rather low, but it increased considerably since 1966 with 0.4 %. The coal mines of the Federal Republic of Germany ever used longwall as the classical method of coal getting. All attempts to introduce bord and pillar mining did not lead to any wider application of this method. The principal reasons, for this appear to have been: - the deeper depth of our workings, - the wish to keep working losses as low as possible and to utilize the deposits opened up by deep and therefore expensive shafts to the furthest possible degree, - the dense sequence of seams and the mutual influencing of the working points, - the high number of disturbances in the geologically much stressed deposits, - and the necessary considerations to the protection of the densely built-upon surface.

Jan 1, 1970