Search Documents

By L. E. Sausa

Measuring the specific gravity of a pulp in concentrating plants is a relative, y simple procedure, but the desired accuracy is often difficult to attain. Many plants use the system of weighing a known volume of the pulp on a scale. In many cases, this method is quite accurate, but obtaining a true sample presents quite a problem. This is especially true when the pulp tends to froth, the solids settle rapidly, or the flow is fast at the point of sampling. There is also the problem of the operator neglecting to take the sample because of duties elsewhere, or, if everything Is apparently running smoothly, he assumes the pulp density is also all right. In 1952, the Pine Creek plant of Union Carbide Nuclear Company began working on a better method for measuring and controlling pulp density. After an extensive investigation of different methods for measuring the specific gravity of moving pulps, the Research Department decided that the bubble tube method appeared to be the simplest and most promising for our applications. It consists of two bubble tubes, of different lengths, submersed in a pulp. Low pressure air is supplied to, the two tubes through sight bubblers to maintain approximately equal volume of air to each bubble tube. The bubble tubes are also connected to a differential manometer, one to each side. Therefore, knowing the vertical distance between the outlets of the bubble tubes, the manometere can be calibrated to measure directly the specific gravity of the pulp. (Figure No. 1 illustrates this model.)

Jan 1, 1960

By Otto Schumacher

Shortcut methods are commonly employed for estimating mining costs for prefeasibility studies. Most of these methods, however, are suitable for earliest stage studies or for internal discussion purposes only. The experts at InfoMine?s CostMine division recommend that any cost estimate completed for purposes of significant decisionmaking or for compliance with Canada?s NI 43-101 requirements be completed using a determinative itemized method. The same basic principles apply for an early stage, intermediate stage, or advanced stage estimate. The only difference is in the level of detail and effort employed. ? Based on the results of a completed resource estimate, an itemized cost estimate begins with development of a conceptual mine plan. Using a surface mine as an example, four elements are crucial no matter what level of study is initiated. Basic geometry of the ore deposit and waste material, with a determination of the expected ratio of waste to ore, a reasonable pit slope angle, possibly requiring the completion of geotechnical studies to predict the waste-to-ore ratio with certainty. ? Determination of the assumed ore and waste production rates. ? Locations of all ore stockpiles and waste dumps. ? Segmental haulage distances and gradients for ore and waste.

Oct 1, 2013

By Julian Glasser

Starting with rutile, containing more than 55% TiO2 and of the proper particle size, the commercial production of titanium tetrachloride via fluidized bed chlorination is relatively very simple and economical. As compared to shaft chlorination, it operates at a much higher capacity for given sizing of equipment, and appears more foolproof, requiring less attention. Operating data were obtained on a 53" diameter fluidized bed chlorinator using Australian rutile and petroleum coke of controlled particle size. Production rates varied from 20 to 50 tons of crude TIC14 per day for a campaign extending over one month. Close to theoretical yields and efficiencies were obtained from the viewpoint of chlorine and/or rutile consumption. Details of important equipment design, critical operating conditions and pertinent results are described.

Jan 1, 1962

By Ronald E. Heuer

It is not possible to accurately predict water flow into rock tunnels during construction, because all of the relevant factors cannot be accurately determined ahead of time. But an estimate is needed, because water inflow can be a major problem during construction, hence also a major concern for project design. There currently is no simple, generally accepted method of estimating inflow. This paper describes a semi-empirical method for estimating possible water inflow based on borehole water pressure test results, using correlations from previous tunnel experience. The method provides an estimate of percentages of tunnel length which will experience different intensities of long term steady state inflow, and provides an estimate of possible initial heading inflow. The method is applicable for distributed sources of water inflow due to rock mass features such as systems of joints and bedding planes, and accounts for different boundary conditions of water head and recharge. The metric system flow units used in this paper are liters per minute (L/min) and liters/minute/meter of tunnel (L/min/m), to be compatible with rock mass classification systems commonly used today.

Jan 1, 1995

By Zachary E. Wedding, Zach Agioutantis

Excavation of underground openings results in the redistribution of the in situ stress into the rock adjacent to the opening. Stress redistribution depends on opening geometry, pillar geometry, material properties, possible confinement, and constitutive models describing the behavior of adjacent rock. This paper presents typical pillar stress distributions for elastic and yielding pillars as a function of opening geometry, material properties, and material constitutive models and highlights the differences between them. Stress distributions are compared with empirical strength profiles that have been developed for coal pillars as well as actual pillar geometries documented for stone pillars.

Jul 1, 2023

By J. R. Weber, R. D. Haddenham, J. H. Bailey

Introduction The Vernal Phosphate Operation is located in northeastern Utah, about 18 km (11 miles) north of Vernal, about 280 km (175 miles) east of Salt Lake City, UT. The plant began initial operations in 1961 under the name of the San Francisco Chemical Co. In 1981, Chevron purchased the operation from Stauffer Chemical Co. In 1982, plant capacity was doubled to about 72.6 kt/a (800,000 stpy) of phosphate concentrate. From 1984 to May 1986, another expansion increased the capacity to 1.2 Mt/a (1.3 million stpy) of concentrate. It also incorporated a number of equipment and process changes designed to increase the overall plant phosphate recovery. A 150-km (94-mile) slurry pipeline, the world's longest phosphate pipeline, was also constructed from the Vernal plant to a new Chevron Chemical and Fertilizer plant near Rock Springs, WY. Over the past five years, plant expansions and the pipeline construction have been accomplished without missing a single concentrate shipment.

Jan 1, 1987

By S. C. Nordeng

The program described in this paper is primarily a test of the possible utility of multiple regression in ore search, It was carried out as a cooperative project between White Pine Copper Company, the Institute of Mineral Research and the Department of Geological Engineering of the Michigan College of Mining and Technology. The authors wish to thank Dr. Cleaves Byers, Associate Professor of Mathematics, MCM&T, and Mr. Robert DeBaubien, Graduate Student in Mathematics, MCM&T, for their work in programming the project for the computer,

Jan 1, 1964

By E. L. Schrader

Statistical Process Control (SPC) is a cooperative arrangement between a component or raw materials supplier and a manufacturing customer. The supplier must analyze his own manufacturing process and determine, predict, and control those variable elements in the circuit which affect finished product characteristics according to the customer's specifications. The results include: control of fluctuations in product characteristics to a narrow range, close communication between supplier and customer, and an increased responsibility for quality control placed on the supplier. In the mining and. processing of airfloated kaolin some unique problems arise with the SPC concept: 1) The SPC system was designed for manufacturing facilities that did not have to deal with natural variations in their raw material; 2) The airfloat process is relatively simple and offers limited opportunity to change processing steps or "fine tune" a circuit for special product needs; 3) Determining adequate sampling frequency for a plant which processes hundreds to thousands of tons per day is statistically difficult; and, 4) Due to the variety of customer industries served, different SPC programs must be set up to deal with widely varying specifications. For airfloated kaolin, SPC is "in line" process control, not after the fact "quality" control. The emphasis must be on statistically valid sampling of the kaolin ore and complete monitoring of its path through the beneficiation circuit.

Jan 1, 1987

By Carlos Fonseca, Gustavo Usero, Roberto Mentzingen Rolo, Gabriel Moreira, Octavio Rosa de Almeida Guimarães

Geological domain modeling is an important step in mineral resources evaluation. The procedure can be laborious and time-consuming, especially in multivariate settings. However, estimates are significantly improved when carefully limited by geological variables. This paper proposes a workflow for geological domain modeling suited for stratigraphic deposits. The workflow consists in automatically defining the domains by using clustering algorithms, generating the surfaces that represent the contacts by interpolation and subsequent triangulation, and simulating the surfaces. The proposed workflow produces consistent and realistic results and allows the user to test different domain configurations and assess volumetric uncertainty automatically and quickly.

Jun 25, 2023

By R. E. J. Putman

The, principle purpose of applying control to any process is to improve -its profitability. Even when considering the impact of a plant on its surrounding ecology this is still, true, since the sanctions felt most immediately from violations of the regulations are the economic penalties or fines which result. 'Economic performance can be improved within a plant in several ways. Steps can be taken to cut the cost or quantity of resources (power, water, steam, reagents) consumed per ton of throughput. Alternatively the operation of the plant can be changed so as to increase product yield per ton of throughput. Or the cost of labor and plant overhead per ton of product can be reduced by raising the total 'throughput, assuming-that the increased amount of product can be sold for the same unit price. In designing a program to improve plant performance, all three routes should be borne in mind. To maximize the return on investment over a longer period, it is also desirable to set up a comprehensive plan of improvement, equipment being specified at each step in the implementation so as to ensure that it fits in with later requirements later implementation being either by means of modular additions or by having the necessary interfaces built into the original equipment. It is much cheaper in the long run to buy features which have been factory-installed, than to have to make provision for their later addition in the field. This paper examines some ways of improving plant performance by the application of various process control techniques using both analog and digital con¬trol equipment. A general philosophy of application is suggested and specific examples described.

Jan 1, 1972

By Harry Asche

Tunnels are frequently specified by owners to be designed to a structural code, often a bridge code. In the USA, AASHTO have created a tunnel code, based on structural principles, the AASHTO LRFD Tunnel Design Specification. The Load Resistance Factor Design method (LRFD) described in the AASHTO title is an approximation to the probabilistic design of structures, based on the independence of load and resistance. This methodology is well known to be problematic in geotechnical design, but it is widely used. The paper considers the difficulties of this approach and describes alternative approaches that would result in more appropriate designs for tunnels.

Jun 13, 2021

By John M. Heckard

It all started with the National Environmental Policy Act of 1969, which establishes that Congress is committed to restore and maintain environ- mental quality. It directs all federal agencies to identify and develop methods and procedures so that environmental parameters and values will be given equal consideration in the decision-making process, along with economic and technical parameters. Section 102 of the Act directs, among other things, that all agencies will submit a detailed statement on: (1) the environmental impact of the proposed action, (2) any adverse environmental effects which cannot be avoided should the proposal be implemented, (3) alternatives to the proposed action, (4) the relationship between local short term uses of man's environment and the maintenance and enhancement of long term productivity, (5) any irreversible and irretrievable committments of resources which would be involved in the proposed action should it be implemented. Passage of this act has been followed by other legislation, both federal and state. The Water Quality Act of 1970 puts teeth into the previously existing Federal Water Pollution Control Act by requiring a "certificate of reasonable assurance that the activity licensed will not violate the applicable water quality standards." The Clean Air Act of 1970 requires that the Environ- mental Protection Agency establish national air quality standards, as well as standards for significant new pollution sources.

Jan 1, 1973

By J. T. Crawford

The purpose of this paper is two fold. It will: (1) examine leasing analysis as a project evaluation criterion, and (2) compare the cost of leasing with other methods of financing. The use of leasing has grown extensively in recent years as a method of obtaining equipment. The computer industry has been highly dependent upon leasing from its earliest days to dispurse its equipment to the customer, while airlines and railroads acquire large segments of their aircraft and rolling stock by leasing. Over the last few years the mining industry has leased haulage trucks, bulldozers and other equipment of similar nature.

Jan 1, 1974

By Martino Scialpi, Miriam Piemontese, Claudio Cimiotti, Matt Kendall, Nicholas Karlin, Roberto Schuerch

The Los Angeles, California JWPCP effluent outfall tunnel will transport secondary-treated effluent from the Joint Water Pollution Control Plant in Carson to the White Point Manifold. Upon completion, through ground conditions ranging from soils to hard rock, the tunnel will be approx. 7 miles (11 km) long with a finished internal diameter of 18-ft (5.5 m). This paper will present the Tunneling Condition Assessment Report (TCAR) and Tunnel Operation Plan (TOP) developed prior to construction, as well as the actual TBM performances achieved along the northern portion of the alignment in soft ground, shallow cover, and beneath a densely urbanized area.

Jun 23, 2024

By Yi Zheng

Under normal circumstances, methane released along a longwall face represents only 10%-20% of the total me- thane emitted from the entire longwall panel. However, there might be a sudden surge of methane at the face which may cause a potential problem because the friction from shearer cutting, support movement, and scraper conveyor dragging can be ready ignition sources. Therefore, to predict the distribution of methane will be critical to prevent possible explosions. In this paper, methane dispersion patterns along a lognwall face are simulated under normal and abnormal conditions. With the simulation of methane released from the face, around shearer drum, and from the broken coal on the conveyor, places with possible high methane content can be identified by different phases of working process and shearer positions. Local ventilation measures are evaluated so precautionary measures can be planned ahead.

Jan 1, 2012

By Duncan M. Lamb

Commercial computer "time-sharing" is a new and powerful tool for the engineer. It is a system of virtually simultaneous use of a digital computer by several individuals. Access to the computer is by means of a conventional teletypewriter which transmits over the regular telephone lines to the computer which may be located any distance from the user. Complex or repetitive computations can be programmed and the speed of computation is many times that which one can do with slide rule and desk calculator. The availability of such a commercial computer "time-sharing" system offered an opportunity to transform a tedious and time-consuming task into one that requires only a few minutes. Until the work of F. C. Bond produced widely accepted mathematical statements concerning the performance of grinding mills, the selection of the proper size equipment was done by comparison with similar operating equipment. Allis-Chalmers systematized Bond's work in a bulletin published in 1963 but the calculations are laborious and the final mill selection still required comparison of the calculated power draw with the power requirements listed in equipment catalogs. This was, however, a step forward from previous procedures. This paper discusses a rapid and simple method of determining the size and power requirement of overflow ball mills. A shared-time computer program has been developed which rapidly calculates and displays the physical dimensions, power requirements, grinding media size and quantity, as well as the important correction factors used. All of these data are calculated from input information which is usually available.

Jan 1, 1969

By J. R. Patts, L. D. Patts, S. J. Janisko, T. Barone

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more efficient and effective use of rock dust. A prototype, flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed in line between the ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over a period of three days at set distances from the fan exhaust to assess the changes in float coal dust levels in the return due to the operation of the scrubber. Mass-based measurements were collected on a per-cut basis and were normalized per foot of advance by the continuous miner. Results show that average float coal dust levels measured under baseline conditions were reduced by over 91% when operating the scrubber. INTRODUCTION In 2012, underground mining in the United States produced over 342 million tons of coal [EIA 2013]. During the cutting, crushing, and transport of this coal, dust is generated and can be entrained in the air ventilating the mine. Title 30 Code of Federal Regulations Part 75.400-1 (30 CFR§ 75.400-1) defines float coal dust as particles of coal that can pass a No. 200 sieve. These coal particles can be carried by the ventilating air into return entries before settling onto mine surfaces [NIOSH 2006]. If this float coal dust becomes re-entrained into the airstream, it can propagate an explosion throughout mine workings [Harris et al. 2010]. Application of rock dust in underground coal mines is required by Federal regulation as a means of preventing the propagation of explosions by float coal dust. In order to meet Title 30 Code of Federal Regulations Part 75.403 (30 CFR § 75.403), 80% incombustible content must be maintained in the composition of dust deposited in mine entries [76 Fed. Reg. 35968 (2011)]. This fraction of incombustible content is increased if elevated levels of methane are present. In order to maintain the required incombustible content, frequent or constant application of rock dust is undertaken by mine operators. Title 30 Code of Federal Regulations Part 75.2 (30 CFR § 75.2) defines the properties of the rock dust that must be used by mine operators."

Jan 1, 2015

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008, “I guess that without the occasional complaint, your mine is probably over-ventilated” (Marks, 2008). Miners are seldom in this situation and spend much of the time trying to find enough air to keep an operation running. With examination, there are usually changes that can be made to increase the efficiency of ventilation systems. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Modifications that result in surplus mine ventilation air could bring financial and environmental benefits. Some issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and nonmetal mines, to ventilate reserves that are deeper, hotter, and further away from fans and shafts, and to meet demands from increased production. This paper discusses successful methods to find additional usable air when there is no extra ventilation capacity. Most of the options presented in this paper are useful for metal/ nonmetal operations but some may be applicable to coal as well.

Jan 1, 2009

By Courtney Chamberlain

The Telfer Project, Australia's newest, largest and most remote gold mine, treats 480,000 metric tonnes of ore grading 9.33 grams per tonne derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded using a continuous strake, table and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, CCD and stellar filters for clarification and precipitate removal. Overall recovery into bullion averages 98 percent. The mill incorporates a number of design features which allow for maximum efficiency and security using a minimum number of operating personnel.

Jan 1, 1980

By Robert W. Miller, Rhoda S. Kriesel

INTRODUCTION With each passing year, the general public becomes increasingly aware of the potential hazards associated with many products and services previously considered unharmful. This new consciousness is especially evident in the workplace, both as the result of advances in scientific understanding and the influx of concerned, responsible professionals into the labor movement. For example, data produced by epidemiologists doing retrospective mortality studies which related mortality to toxic substance exposures has often been the prime motivating factor behind reductions in exposure standards. This certainly has been the historical case with many radiation exposure standards, including the limitations set for "Working Level" exposure. The concept of "Working Level" was introduced in PHS Publication No. 494 as a result of both the difficulty in relating radiation units to biological effects and the complexity of interaction of radon daughters with the physical environment. WORKING LEVEL One working level is defined as any combination of radon daughters in one liter of air that will alternately release 1.7 x 105 MEV of alpha energy during decay of 210pb (RaD). Its usefulness is that working level can be readily measured in both the field and the laboratory. Because of this, existing occupational exposure standards for radon daughters in both the U. S. and other countries use working level as their basis. In the U. S., the last twenty years has witnessed a significant reduction in radiation exposure standards from 120 working level months to 4 working level months per year. New international standards are being proposed that would be only slightly higher than these current U. S. standards. POTENTIAL EXPOSURES TO RADON DAUGHTERS The universal use of nuclear power, along with the transfer of nuclear technology to developing nations, has significantly increased the demand for fuels. As a result, uranium mining operations have expanded and increased numbers of miners are regularly exposed to radon daughters. In addition to potential exposures in uranium mines, other deep mines such as tin, gold, platinum and tungsten, also have potential exposures due to the distribution of uranium and its accompanying radium throughout much of the earth's crust. The energy crisis has also prompted interest in general population exposure to radon daughters in buildings. Many homeowners, using additional insulation and caulking to seal cracks and conserve energy, have reduced indoor ventilation to the point where working level exposure could become significant, especially in homes with unventilated crawl spaces. In fact, several serious exposure situations have occurred where mine tailings were used for building materials. MEASUREMENT TECHNIQUES Historically, rapid and convenient measurement techniques have been actively sought to improve the ability of ventilation engineers to limit mining exposures through ventilation control. A number of measurement techniques have been developed, including the Kusnetz method (further elaborated by Shalaynev) and techniques developed by Rolle and Tsivoglou. All, however, suffer from similar handicaps that prevent their usefulness in the mining environment. Their main limitation, in terms of minimizing employee exposure, is the elapsed time from the start of sampling until the results can be calculated. It is usually 40 to 90 minutes. This time delay presents both serious economic limitations as well as the potential for exposing workers to high radon daughter concentrations until calculations are completed and corrections made. Further reducing the utility of the Kusnetz and Tsivoglou techniques is the need for tedious calculations that increase the possibility of human error along with the need for cumbersome sampling equipment that is not ideally suited to the mining environment. INSTANT WORKING LEVEL METER To alleviate these problems, the idea of an Instant Working Level Meter was conceived by several groups. Several such instruments were proposed, built, and tested with disappointing results. Although the concepts behind them were sound, the instruments simply failed to measure working level without excessive distortion. In addition, their cost was relatively high, gamma background presented a problem, and sophisticated computations were necessary to determine working level. In short, these systems lacked the design engineering that would make them suitable for the demands of a mining environment.

Jan 1, 1981