Search Documents

By D. P. Plute

The mechanization of the materials management function must contribute to the overall goal of optimization of profits. A computerized system contributes to the profitability of the company by saving more than it costs to operate. Design and implementation of the sys- tem must respond to the needs of users, the operating environment of the property, and must support the objectives of materials management. Three basic functions interact within the scope of materials management. They are inventory control, purchasing, and warehousing which have the following objectives: 1) Inventory control-to request materials in a timely manner and in quantities that provide the best level of support to users at the lowest cost. 2) Purchasing-to purchase requested materials and services at the required time and at the lowest cost. 3) Warehousing-to efficiently receive, store, and issue materials and to prepare accurate transaction documents for the activities. The development of the mechanized materials management system will require a plan and objective analysis by management and system users of system requirements. A typical plan would include: 1) System Design Objectives-the development of objectives that support mechanization of the materials management function. 2) System Characteristics and Concepts- the development of key system concepts and characteristics, which identify the needs of materials management. 3) System Inventory Item Classification- development and assignment of inventory category codes to inventory items. 4) System Order Decision Rules-the development of decision rules and forecasting techniques to minimize the inventory investment and to provide acceptable support levels. 5) System Report Structure-the development of a report structure to support the goals and objectives of materials management. 6) System Report Design-the development and design of reports for effective utilization of the mechanized system.

Jan 1, 1979

By R. J. Andreini

Solvent extraction is widely used in hydrometallurgical processing of uranium for purification and upgrading leach solutions prior to recovery of metal values. Conventional solvent extraction processing utilizes mixer-settler units to achieve mixing of the aqueous and organic phases. Use of mixer-settlers permits continuous treatment of feed, but the processing rate is restricted by the time required for phase separation after mixing. Because of the high-shear type mixing used in a mixer settler a portion of the organic phase becomes mechanically entrained in the aqueous resulting in loss of extractant. For this reason application of mixer-settler units is often limited by the settling area required for phase separation, especially for systems where high volume throughputs are desirable or necessary. Several alternatives to mixer-settler operations involving the use of column extractors have been proposed. Packed columns (1-2), in which organic and aqueous phases are fed countercurrently, utilize packing materials similar to those used in gas absorption or distillation columns. Extraction columns utilizing rotating(3-5) or reciprocating elements(6-7) to achieve mixing have also been developed. Van Dijek(8) originated pulsed columns, in which mechanical or air pulsing of the phases enhances the mixing in the vessel. Each of the above column processes involve varying degrees of mechanical complexity which may lead to operational difficulties.

Jan 1, 1975

By Mahmut Altiner

In the present study, the use of horse residue as an alternative reducing agent in the roasting of a low-grade goethite ore containing 17.60% Fe was investigated. Additional roasting experiments were carried out with corn starch and without reducing agent for comparison. Each roasted product was characterized using X-ray diffraction (XRD) and magnetic hysteresis (MH) loops analyses. The optimum roasting conditions (roasting temperature [400, 500, and 600 °C], reducing agent/ore ratio [0.04, 0.08, and 0.12], and roasting time [10, 20, and 30 min]) were investigated based on the Taguchi approach. The magnetic susceptibilities of the roasted sample with the addition of reducing agents were higher compared to that of the roasted sample in the absence of reducing agent. Experimental findings indicate that the horse residue can be used as the reducing agent. Finally, an iron ore concentrate assaying a Fe grade of 62.12% with a recovery of 56.93% was prepared using wet magnetic separation at a magnetic intensity of 0.5 T from the ore roasted under the following roasting conditions: roasting temperature of 500 °C, reducing agent/ sample ratio of 0.08, and roasting time of 30 min.

Jun 3, 2020

By Rodney R. Krause

In attempting to tell the general public about the coal industry's land reclamation efforts, we have often said, "We're not doing things by the book, because we're still writing it." Like any good catchphrase, the statement is not only striking but true. It is particularly true in the mountains of Appalachia, where the problems of mining; and of reclamation are made more intense by the nature of the terrain. Mining and reclaiming the land "by the book' --which is to say by the methods of contour mining traditionally used in hill country--hasn't worked too well. So a lot of conscientious coal operators and associations are trying new methods--new ways of mining, new machines for seeding and planting, and new species to seed. Not all their experience can be transplanted to other areas, and of course I don't believe that Appalachia is the only place where new methods are being developed. Nevertheless, there's enough action in Appalachia to make a detailed examination rewarding, so let's focus on the hills to see what's new.

Jan 1, 1970

By A. Hekmatnejad

"The objective of this work is to validate a methodology for spatially predicting the fracture intensity, defined as the average fracture area per unit volume. First, using the observations from drill holes, the fracture intensity is directly inferred at the support of drill-hole composites based on a Terzaghi correction. Subsequently, the composite values are interpolated to larger blocks. The methodology is tested on sets of simulated fracture networks, in which each fracture consists of a disc with a random diameter, random position and random orientation. For each of these simulated networks, one can calculate the actual fracture intensity within any region of space, based on geometric considerations. A regular sampling mesh is then defined to emulate a set of vertical drill holes and the proposed methodology is applied to predict the fracture intensity, both globally and locally. The actual and predicted fracture intensities are finally compared, showing that predictions are unbiased, insofar as, on average, the prediction error is always close to zero. Also, the error dispersion increases when the support of the prediction decreases, which is consistent with the well-known support effect. In practice, the proposed methodology allows predicting fracture intensity based exclusively on drill-hole information, without the need for simulating fracture networks in space, hence its interest. INTRODUCTION The characterization of fractures in rock masses is an important part in the evaluation of mechanical and hydraulic properties of rocks. Fractures have a large impact in disciplines such as reservoir engineering, safety of underground storage of CO2 or of nuclear waste, assessment of high-enthalpy geothermal installations, safety of mining exploitations, efficiency of in-situ leaching operations or of extraction by block-caving. As a rock mass property, fractures must be characterized in the three-dimensional space, whereas observations are limited to 1D (drill holes) and 2D (outcrops, drift walls), moreover very often to rather short stations, so that the available data are subject to geometric bias, truncation and censoring. Fracture characteristics includes the number of fracture sets and, for each set, the number, orientation, spacing, location, shape and size of the fractures must be inferred from data sampling. Some important parameters that are considered nearly in all models are fracture intensity and fracture size."

Jan 1, 2016

By J. C. Gathje

The Robinson copper ores were mined for many years from pits containing varying ore grades, sulfide and oxide ore types, and differing mineralogy. The ores also contain gold and molybdenum values, and their recoveries are an integral part of the flowsheet development. Metallurgical responses were characterized using a standard flotation procedure. Further studies investigated primary and regrind particle sizes, reagents, and other variables. The metallurgical testing was supported by mineralogical studies. Results demonstrated a high degree of metallurgical success for flotation. Final copper concentrates ranged in grade from approximately 28 to 30% copper and copper recoveries were 89 to 95% based on laboratory and pilot plant data.

Jan 1, 1992

By M. J. Laurila

Simulation of coal preparation circuits is becoming a widely practiced technique used for the design of coal preparation plants. On a much more limited basis, simulators are finding application in off-line process control. A typical application in the latter category involves inputting projected coal washability data for a shift into the simulator and using the software to optimize product quality and recovery within a range of predefined specifications. The plant is then operated at SG?s of separation determined from the simulation exercise for the one shift time period. This procedure is useful in that it incorporates some form of advanced planning into preparation plant operations. There is an attempt made to reflect changes in feed coal quality on a shift by shift basis rather than continually running the plant near design specifications with changes in SG?s of separation being made in response to an inadequate sampling program which only provides a spot measurement of material that has already passed through the plant. Instead of instituting changes on a shift by shift basis, NHI has proposed a method whereby monitoring three major operating parameters, * Feedrate to jig * Flowrate from hydrocyclone overflow * Density from cyclone overflow the ongoing plant operating performance can be accurately predicted on a continual basis, i.e., updated hourly. Using a distribution curve to predict the split between the clean coal and refuse from a given separator does not account for variations in efficiency that occur as a result of variations in operating parameters. NHI and Arch have studied the effect of both jig loading and solids content in the recirculating load to the jig on product quality. As a result, relatively simple measurements can be made on-line in a preparation plant which will provide input data to the simulation program that enables the prediction of jig/hydrocyclone circuit performance on a real time basis.

Jan 1, 1985

By P. Soros

To accommodate the immediate and long term growth of the Hunter Valley, one of Australia's major coal producing regions, a third coal terminal was required in the Port of Newcastle, N.S.W. The initial capacity required was 15 million tons per annum, made up of 40 different blends, to be expanded to 50 million tons of 100 different blends, made up from 70 grades. Coal arrives in 3,200 ton unit trains, a total of 16,000 trains in a year.

Jan 1, 1986

By J. G. Asbury

Broadly conceived, the demand for electricity depends upon three sets of variables: (i) the growths of the many individual demands for energy services; (ii) the competitiveness of electrically driven technologies in meeting these demands; and (iii) the energy-conversion efficiencies of installed electrical technologies. The first set of variables establishes the size of the potential market; the second, the market penetration of electrical equipment; and the third, the quantity of electricity required to operate the equipment. All forecasts of electricity consumption ultimately depend upon inferred or assumed relationships to describe the future behavior of these variables. This partitioning of the demand-forecasting problem is conceptually useful and will guide the discussion presented in this paper. However, it is also something of an oversimplification. Examined in more detail, the electricity fore-casting problem is exceedingly complex. The variables mentioned above are, in turn, found to depend upon more fundamental sets of demographic technological, resource, and policy variables. The demand projections developed by the major forecasting services are usually developed in terms of these underlying variables, which themselves must be independently forecast.

Jan 1, 1985

By Dennis S. Kostick

Soda ash is produced in over 39 countries by the Solvay ammonia-soda process or by mining natural sodium carbonate deposits. The total production of soda ash in 1980 is estimated at slightly over 29 million metric tons. Synthetic production accounted for over 75% of this amount with the balance of production originating from natural sources (either trona or sodium carbonate-rich brines) found primarily in the United States, Mexico, Kenya, and Chad.

Jan 1, 1981

By Jiang Su, Alan Bloodworth

"Composite sprayed concrete lining (SCL), consisting of two layers of permanent sprayed concrete separated by a layer of spray-applied waterproofing membrane, represents the latest development in SCL tunneling, but presents several challenges to designers. This paper aims to address the following issues: (1) how to simulate composite action, (2) behavior of a composite SCL tunnel, and (3) how to utilize composite action to achieve lining thickness efficiency. It firstly sets out the background to the composite SCL concept, and then presents a strategy for numerical investigation. The main part of the paper is the presentation and discussion of the simulation results, focusing on the lining deformation, load sharing and the safety margin of both linings. Interface stresses are also examined. It is found that significant secondary lining thickness reduction may be achieved by utilizing composite action. Challenges for the design of composite SCL tunnels are briefly discussed at the end. INTRODUCTION Sprayed concrete lined (SCL) tunnelling has seen rapid development over the last twenty years in the UK (Su 2013). One of these developments has been the replacement of traditional sheet membrane and cast in situ secondary lining with innovative spray applied waterproofing membrane and sprayed secondary lining system, which has been adopted in recent major projects, such as Crossrail (Pickett 2013), and brings many benefits to the construction (Dimmock et al. 2013). The combination of sprayed primary lining, spray applied waterproofing membrane and sprayed secondary lining is perceived to provide a structurally efficient lining system that outperforms the traditional lining system, which consists of sacrificial primary lining, sheet waterproofing membrane and cast in situ secondary lining. The claimed benefits in structural performance arises from the composite action between the sprayed primary and secondary linings via the spray applied waterproofing membrane, which produces a much stiffer cross-section and therefore a more efficient use of materials. Early investigations on the design of composite SCL tunnels were carried out without (1) definite and reliable long-term interface parameters, (2) a verified numerical modelling technique, or (3) consideration of different stress histories between primary and secondary linings (Thomas and Pickett 2011, Marcher et al. 2011). This paper reports the findings from a numerical parametric study on a typical composite SCL tunnel with varied secondary lining thickness. The results show that the true benefit of composite lining arises from the optimisation of the lining thickness (stiffness) ratio between the primary and secondary linings to achieve secondary lining safety and thickness efficiency at the same time."

Jan 1, 2016

By James R. Aggson, Verne E. Hooker

GENERAL CONSIDERATIONS The design of a mine or any underground opening in rock is similar to the design of any other structure, such as a building or a bridge, in one important way. This similarity lies in the fact that the stability of the structure is a function of the loads that will be applied during the structure's expected lifetime. In the case of an underground opening, the applied load is the product of the existing in situ stress field and the concentration of this field that is produced by the extraction of a load¬bearing material. Thus, a knowledge of the in situ stress field is considered a basic requirement in the design process and essential to the eventual stability of the underground structure (Duvall, 1976; Obert, 1972; Merrill and Peterson, 1961; Dahl and von Schonfeldt, 1976; Hedley and Wilson, 1975). The in situ stress field can be used along with the physical properties of the rock masses involved, the ge¬ometry of the various rock types, the geometry of the openings involved, and a failure criterion to evaluate structural stability of a planned mine by theoretical or numerical techniques. This same information can be used to investigate ground control problems in existing mines. In situ rock stress determinations can be separated into three categories: the determination of applied stress, also called the absolute or field stress; the deter¬mination of concentrations of the field stress near open¬ ings; and the determination of changes in rock stress as load-bearing material is removed. The applied stress field is more difficult to determine than are stress changes. Various instruments and techniques have been developed to determine applied rock stress and stress changes in rock. ABSOLUTE OR FIELD STRESSES Theoretical Considerations In the absence of actual measurements, it is often assumed that at any point, the vertical stress is equal to the weight of the overlying material. [ ] where S„ is vertical stress, S is average weight density of overburden rock, and h is depth from the surface. This is normally consistent with actual experience. The horizontal stresses are assumed to be equal and related to the vertical stress through the Poisson effect. [] where Sh is horizontal stress, S„ is vertical stress, and v is Poisson's ratio. The derivation of Eq. 2 is dependent on lateral con¬finement of the rock mass. An increasing amount of information is rapidly becoming available which indi¬cates that the in situ stress field at a particular location cannot simply be assumed to be a gravity-induced stress distribution in which the secondary principal stresses in the horizontal plane are due to confinement and Pois¬son's effect. Rather they can be a complex function of gravity loading, regional stresses, structural features, ex¬cavation geometries, and variations in surface and/or possibly basement rock topography. Furthermore, the underground principal stress dis¬tribution is not necessarily vertical and horizontal as is often assumed. The deviation of the three-dimensional stress distribution from vertical and horizontal can be due to a combination of both topographic (Hooker, Bickel, and Aggson, 1972) and structural features.

Jan 1, 1982

By E. Bonates

Dispatching systems have attracted considerable attention in the last years due to substantial gains in productivity achieved through their implementation. These systems will be extensively used in the future by mine operators as a means of optimizing productivity. This paper describes a computer simulation model designed to study the feasibility of continuously dispatching trucks in open-pit mines based on different operating procedures. The system developed is semi-automated and performs an active role by suggesting to the dispatcher the best assignment according to each specific circumstance. It is modeled based on an advance-clock increment to reduce computing time and allows the insertion of heuristic dispatching policies and equipment real-locations when breakdowns occur. Dispatching procedures taking into account long-term production objectives are considered in system development.

Jan 1, 1988

By R. L. Grayson, J. R. Warneke

Environmental conflict between the public and private sectors, including mining, is highly visible and often based on deeply divergent environmental, social, and economic values. In order to achieve sound public policies by government, scientifically rigorous and objective analyses of mining’s impacts are demanded. Material flows accounting and analysis, linked with other data to generate indicators of environmental, social, and economic impacts of mining activity are means toward providing cogent input into public policy-making on key issues. This paper will present a material flows analysis scheme for the coal industry and recommend derived, objective indicators of coal mining’s impact on society.

Jan 1, 2004

By K. O. Groves

Although chlorine oxidation has been found to be effective in destroying the CN ion, an excess of chlorine is needed to drive the reaction to completion. This often results in the formation of residual chloramines, which are toxic to aquatic life and often regulated by various states. The interhalogen, bromine chloride (BrCl), has been found to be just as effective but without the formation of persistent, residual chloramines. The hydrolysis and subsequent disproportionation of the highly-polar BrCl molecule essentially yields a solution of hypobromous acid (HOBr) and nonoxidizing hydrochloric acid (HC1). Studies have been carried out to directly compare the mechanism of CN destruction with chlorine and bromine chloride.

Jan 1, 1982

By Richard F. Hewlett

The purpose of this paper is to provide a framework within which problems in the evaluation, development, and operations of a mineral property can be solved, Solution of these problems must be made with a computer because of their complex nature, Individual problems will be collectively discussed in terms of an overall objective - computation of the optimum mine limits. The concept of quantifying geologic and mine sampling data has been advanced and demonstrated in the United States by two pioneers in the application of statistics. These men are, respectively, Dr. W. C. Krumbein Northwestern University, and S. W. Hazen, Jr., U. S. Bureau of Mines, Dr. H. S. Sichel and D. G. Krige of South Africa have pioneered specific applications of statistics, particularly to gold deposits. Implementation of statistical and mathematical methods to the solving of problems in the mineral industry creates the need for a computer. The steps required to solve evaluation, development, and operational problems with a medium sized computer are discussed in this paper.

Jan 1, 1963

By Tatiana Kotrikova, Steven Kolarz, Alan Kolodne, James Parkes, Matthew Goff

The WMATA Yellow Line is the section of steel segmentally lined tunnels that have experienced leakage and significant corrosion in isolated areas. A three part rehabilitation design has been developed for curtain grouting, structural repairs, and corrosion protection to provide continued performance. As WMATA’s first Construction-Manager-at-Risk (CMAR) project, the design development benefitted from collaboration with the Contractor through the final design development process. Rehabilitation work started in Fall 2022 and will be completed by late Spring 2023. Details of the project, the remediation design, and the process and benefits of the CMAR approach in the design development are presented.

Jun 13, 2023

By P. J. G. du Toi

Anaconda's experience with percussion longhole drilling in Butte, Montana, has consisted of six phases: 1. Drilling horizontal blast holes in stopes with push feeds. 2. Ring and parallel blast hole drilling in longhole stopes with bar mounted as well as skid jumbo mounted longhole drifters. 3. Ring and parallel drilling in raise climber shrinkage stoping using special raise climber drilling decks designed and built in Butte, Montana. 4. Parallel longhole drilling in horizontal cut and fill stopes with monorail jumbo. 5. Drilling water drain holes between mine levels. 6. Drilling leach holes through caved zones into old stope workings for leaching purposes. 7. Sample hole drilling.

Jan 1, 1970

By Eric Forssberg, Mats Hallin

INTRODUCTION Evaluation and optimization of mineral processes has been going on since the the first plant started hundreds of years ago. A huge mass of knowledge has been collected since then. The main problem with this type of empirical knowledge of complex processes is that it is very difficult to formulate and document. The methods used for collecting the knowledge is not consistent but-varies with "he person" that does it. In the late 60's and early 70's efforts were made to use computer based techniques to evaluate process performance and to formulate process models for mineral processes. Models were developed, such as the flotation model by R. P. King (1973) which is still used to simulate flotation circuit behaviour. During the 70's. a number of mass balancing packages were developed together with process simulation packages. The industrial sector also made great efforts to develop and utilize computer based systems for process control and evaluation. The expert system that BOLIDEN created in 1974 at the Kristineberg plant was a remarkable achievement considering the hardware (CDC 3600) and the software tools (FORTRAN) available at that time. The main obstacle to successfully implement optimizing computer control of mineral processes was and still is the limited knowledge about the dynamics of complex processes. There are, however. many activities going on in this area today and it seems that the technology is very near a break through. Process evaluation is the most important tool to improve and maintain the optimal performance of a process. Today dedicated computer based techniques are used for fast and reliable screening of the processes. The stages in process evaluation consist of three basic steps: - Data acquisition, manually or by data logging. - Data refining, mass balancing and parameter calculation. - Data evaluation. The refined data can then be used for model construction/calibration and subsequently for process simulation. This paper describes two studies where the techniques mentioned above are used to evaluate and simulate

Jan 1, 1991

By W. G. Cornwall

The mining field, inclusive of the treatment plant is located in the foothills, five miles inland from the northern coast of Viti Levu, the largest and most important island of the Fiji Group. Gold and silver occur as tellurides, associated with the sulphides, and as minor occurrences of electrum.

Jan 1, 1975