Search Documents

By Brad Grothen

What is the most economical way of tunneling in mixed ground that may experience high pressures? Non-continuously pressurized, mixed ground Tunnel Boring Machines (TBMs) are being utilized to deal with a wide range of geology. Continuous improvements in these mixed ground machines allow for ever-increasing efficiency and reduction of project risk due to unexpected conditions. We will explore the performance of recent mixed ground machines throughout the world and then look at how new improvements to mixed ground machines will enable excavation of an expanded range of ground conditions. These conditions include mixed ground with low fines, mixed face rock, and fracture/fault zones with high pressures where in the past a Slurry TBM may have been utilized.

Dec 1, 2022

By Milton E. Wadsworth

The evolution of engineering education and research has been profoundly influenced by computer technology and has concomitantly followed changes in this technology. Today, virtually all faculty have access to at least two hierarchies of computers: desk personal computers and at least one echelon higher (workstations or a variety of mid-sized computers). Most faculty have access to three or even four hierarchies: the two listed, plus super-mini and super computers. The ready availability of computers at a low cost has increased dedicated and site-specific computer technology. This has permitted universities to move into the field of macro-engineering, to address increasingly complex problems in resource recovery, manufacturing and many other areas, including important societal problems, like the environment. The creation of university research centers indicates the growing importance of macro-engineering involving large systems of interactive components. Funding agencies have increasingly favored such centers since they cross disciplines, generate inter-university consortia and foster university-industry programs.

Jan 1, 1992

By C. J. Bise, D. A. Poukhovski

Hazard recognition and prevention of accidents are two components of the 30 CFR 48 training requirements, which are mandated for new miners and newly employed experienced miners. These components are also part of the annual refresher training course required of all miners. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine and shall include a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition presents a particular challenge to safety-training specialists, because they are often limited in their ability to adequately gauge the level of awareness of the individual prior to training. Further, they must also assure that the training is relevant and presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics, because it can be used in pretraining and posttraining modes for assessment of training effectiveness, in addition to its use as a presentation tool. This article presents a recent approach, developed at The Pennsylvania State University, that applies the technology for the assessment and instruction of accident prevention through hazard recognition. The application is prepared for surface coal mines.

Jan 1, 1999

By Gill G. Geesey, Michael R. Hankins, Paul L. Wichlacz, Anita Gianotto, John G. Jolley, Randy B. Wright

Thin films of copper [2.0 nm on germanium internal reflection elements (IREs) and 3.4 nm on germanium discs] were exposed to 10% gum arabic (aqueous solution) , 2% alginic acid (aqueous solution), 1% bacterial culture supernatant (BCS, simulated seawater solution) and 0.5% Pseudomonas atlantica exopolymer (simulated seawater solution). The IRES were monitored in situ, in real time using fourier transform infrared/cylindrical internal reflection/attenuated total reflection spectroscopy as a function of time at ambient conditions. The discs were characterized (pre- and post-exposure) by X-ray photoelectron and Auger electron spectroscopies. Ancillary graphite furnace atomic absorption spectroscopy was used to monitor the removal process of the copper thin film from the germanium substrates. Results indicate that Cu was oxidized by gum arabic, alginic acid and BCS. Furthermore, Cu was removed from the Cu/Ge interface by all four polymers. The Cu was found associated with the polymer solutions.

Jan 1, 1989

By Ron F. Schritt

Over the many years since the development of the steam powered shovel, various powering and control techniques have been employed for the various shovel functions. While volumes have been published on this subject, this paper will be limited to a very brief discus-sion of one of the latest of these and its application to a unique machine. The evaluation of the subject machine is far beyond the scope of this discussion, which will be limited to the techniques and equipment employed, and the considerations involved in their choice. The basic requirements for any power and associated control system for any power shovel function have remained relatively un-changed over the years. To the extent possible, such an equipment grouping must be: Easy to install during fabrication Easy to maintain and repair by available personnel Life cycle cost competitive Adequately reliable Adequately responsive And as may be expected these factors are arranged in various orders of priority by different manufacturers and users. All the various time honored approaches have to some extent fulfilled these require-ments but were discarded or fell into disuse when more effective approaches were developed. The latest in this long line of develop-ments and perhaps the most promising is that of electro-hydraulic controls and hydraulic drive.

Jan 1, 1977

By Fathi Habashi

SELENIUM AND tellurium are by-products of electrolytic copper refining. Copper anodes contain 0.01-0.2 % Se and up to 0.04 % Te; during electrolysis these deposit as a slime at the bottom of the cell. Such slimes contain 2-15% Se and 0.5-8 % Te, as selenides and tellurides of gold, silver, and copper. The following compounds have been identified in the slimes: (Ag, Au)Te2, Ag2Se, Ag2Te, CuAgSe, Cu2Se, Cu2Te. Anodic slimes from copper electro¬lytic refining are a grayish black powder, minus 200 mesh. When this complex mixture is decomposed in an acid medium, elemental selenium and tellurium can be obtained, while in an alkaline medium, both metals go into solution. Acid leaching The slime is charged in acid digesters of 800-900 lb capacity, heated to 260°C with 78 % H2SO4, for 8-12 hr. During digestion the following reactions take place:

Jan 1, 1970

By Jorge Rubio, Luis Valderrama, Carlos Pérez

This work describes the effect of the degree of energy transferred to the pulp, during the conditioning stage, on gold flotation fines recovery, grade and kinetics, with three types of frother (Dowfroth 250, pine oil and MIBC) and amyl xanthate as collector. Best results show an increase in 24% recovery and 50% in concentrate grade, depending on the intensity of conditioning and type of frother (better with Dowfroth 250). For low or intermediate energies (0.5-1.5 kWhlm3 pulp), the fine particles adhere to larger ones, increasing the recovery due to a mixture of carrier (pyrite, in this case) and autogeneous carrier flotation and at higher shear (2-3 kWhlm3 pulp), gold fine particles aggregate themselves. These phenomena are demonstrated by measurements of flotation rate, true flotation (flotation by actual particle-bubble adhesion), and by the amount of entrained particles. Alternatives for this type of pulp conditioning and mechanisms involved are discussed.

Jan 1, 1995

By Gerrit V. R. Goodman, Charles D. Taylor

A technique was developed to determine the fraction of air recirculated from the scrubber exhaust toward the face and the fraction of gas captured by the scrubber. To determine these two values, a series of tests was required. In the first test, gas was released at the face area and concentrations measured at the scrubber exhaust. In the second test, gas was released directly into the scrubber with concentrations again measured in the scrubber exhaust. The simultaneous solution of two independent flow expressions gave values of recirculation and scrubber capture. A series of tests was conducted with various combinations of scrubber flow, curtain flow, setback distance, and machine location. Statistical analyses then were conducted to determine those factors which influenced the levels of scrubber recirculation and scrubber capture in a deep cut. INTRODUCTION As cutting depths increase, the trend is toward the use of blowing face ventilation systems. With these ventilation systems, the potential exists for recirculation between the scrubber exhaust and the intake air stream. One concern is that methane gas, having been removed from the face area, is subsequently recirculated back into the intake airflow. Under these conditions, methane-laden air could be substituted for fresh intake air, leading to increased methane concentrations at the face. There is currently no standard for recirculation between the scrubber and intake airflows. The implied understanding of the Mine Safety and Health Administration (MSHA) is, and has always been, that any recirculation of ventilation air is unacceptable. To minimize recirculation potential, MSHA suggests that operators maintain scrubber and curtain flows within 0.47 m3/sec (1000 cfm) of each other. Given that recirculation may occur in some circumstances, the question arises as to how much recirculation constitutes a hazard for the face workers. Unfortunately, there is currently insufficient information to answer this. Emphasis must instead be placed on means to quantify the amount of recirculation between the scrubber and face area. Methods must also be examined to control this phenomenon. This paper presents a technique for quantifying recirculation and scrubber capture levels in a blowing face ventilation system. Several ventilation parameters are investigated to determine their effects on these levels. DEVELOPMENT OF RECIRCULATION EXPRESSIONS One way to measure airflow quantities at a point near the face would be to measure the gas flow rate Qgas, and gas concentration c at that location. The airflow Qair, would be simply the ratio of these two values, Qair, = Qgas/c. Although gas concentration values, c, can be obtained easily with existing gas monitoring equipment, it is more difficult to obtain gas flow readings, Qgas, at specific locations. To obtain these values of Qgas, another method was needed. Previous work in this area was conducted by Kissell and Bielicki (1975). However, the calculations in their model assumed a constant gas concentration in the region around the continuous miner. In a deep cut, it is questionable that gas concentrations would remain constant or uniform around the mining machine. The technique presented here does not rely on this assumption. It instead assumes that the gas concentration in the scrubber exhaust remains constant. A quantity of gas released at the cutting face either flows into the scrubber inlets or bypasses the inlets and flows around the off-curtain side (in this example, the right side) of the continuous miner (Figure 1). The fraction of the face gas that flows

Jan 1, 1993

By William G. Pariseau

The purpose of this paper is to present a design procedure for the quantitative estimation of support load requirements in underground mines. Emphasis is upon the basic features of support behavior common to a large variety of support systems-bolts, timber sets, stope fill, steel arches, concrete liners and so forth. A strong reliance is placed upon fundamental principles and modern computing techniques for their quantitative implementation. Example problems illustrate the approach. Where artificial support is required, the ground in the vicinity of the face usually stands unsupported long enough for the support to be installed. At the time of installation, the load transferred to the support from the adjacent rock is essentially zero, although in some cases there may be an initial set load, for example, from timber blocking. With the passage of time and advance of the face, ground motion loads the supports. If the support system is properly designed, then the additional loading poses no threat to the safety and productivity of operations. If not, then difficulties may arise including high maintenance costs, hazardous work conditions and reduced productivity. Of course, over-design can be equally wasteful. Quantitative estimation of support loads is therefore essential to overall efficiency in mining.

Jan 1, 1975

By Jaime Lomelin

[First of all I want to thank the Society of Mining Engineers of AIME for the opportunity to present what Industrias Penoles, S.A. is doing in Mexico to reach the basic objetive of the enterprise without compromising, in short or long term, the living conditions of the community or attempting in an irreversible form against Nature. Industrias Penoles, S.A. is one of the largest mining and metallurgical companies in Mexico. It was founded in 1887 and at the turn of the century installed a lead smelting operation close to the village of Torreon, which became city five years after the start up of the Penoles smelter. Now Torreon has a population close to 300,000 inhabitants. In 1974 Penoles is still the largest industry in Torreon and the dynamic growth of the city is close related to this factor. Today Penoles in Torreon has a lead smelter with a capacity of 130,000 metric tons/year of bullion, an electrolitic zinc plant of 105,000 metric ton/year, and it is modernizing its lead smelter to control pollution and expand it to 190,000 metric ton/year of bullion including all the services and refinery. The Penoles complex in Torreon is the biggest in the non-ferrous metals field in Latinoamérica.]

Jan 1, 1974

By Leo Wagner

In relation with the construction of the Sölk power station in Steiermark, Austria, tenders were called in October, 1976, for the construction of the 12-km "Donnersbach collector tunnel" by "Steirische Wasserkraftund Elektrizitäts AG". The specified showed both conventional blast tunneling as well as mechanical excavation with a tunneling machine, diameter 3.55 m. Total construction time from the date of the invitation to tender was given as 4 years. Part of the project was the construction of a concrete circular tunnel lining 20 cm thick. In 1977 the contract was awarded to "Arbeitsgemeinschaft Donnersbach", a joint venture formed by two companies, G. Hinteregger & Söhne, Salzburg, and G. Hinteregger, Bregenz. It provided for the project to be carried out with a tunnel boring machine. GEOLOGICAL DATA The entire tunnel was to be bored through a complex of the garnet mica schist group of the Wölz schists formations. These range from highly quartz-bearing to quartzitic mica schists, with thick, discordantly interstratified beds of marble and dolomite. In the western sector the axis of the collector tunnel intersects the bedding at an angle of 30° to 40°, in the eastern sector the bedding is about

Jan 1, 1979

By Michael J. Taylor

Introduction A prime goal in the design and operation of uranium milling waste or tailing disposal systems is to mitigate adverse effects of tailing liquid on the adjacent groundwater. Adverse effects are often defined as modifying the groundwater quality in such a manner as to have detrimental health effects on downstream users. To accomplish this goal, the following three types of systems are employed with regard to the seepage and groundwater aspects of waste disposal: Type I Systems Seepage is allowed to occur unabated from the tailing disposal facility. Detrimental radionuclides and chemical elements are prevented from causing adverse downstream effects by natural purification actions in the subgrade geologic materials and the near zone groundwater. Monitoring is required to assure the predicted natural purification is occurring. The consequences of seepage loss is minimal since the m be predicted with current investigation and analytical techniques and can be evaluated as to effectiveness during operations. Type II Systems Seepage is partially retained in a waste impoundment or leakage from a designed retention system is anticipated. Natural purification is relied on for controlling migration of detrimental radionuclides or chemical elements, or contingency planning is employed to collect and return the tailing liquid to the impoundment. Installation efforts and concern for escape of tailing liquid are greater than for Type I systems, but extra precautions to preclude all seepage are not implemented. Monitoring is required to detect leakage and/or assure the natural purification of escaping tailing fluid. The consequence for accidential excusions are moderate, and will be excessive only if massive system failure occurs. Type III Systems Seepage is totally restricted by a costly system constructed and operated with extra care. Natural

Jan 1, 1980

By J. R. Allen

Environmental laws and regulations have proliferated over the last two decades. 1/ Within the last year, Congress has dramatically expanded the scope of the Superfund program 2/ and has enacted significant new amendments to the Clean Water Act.3/ In addition, EPA has shown no signs of slackening the pace at which it promulgates new regulations to implement statutory programs. The agency projects that over the next few years it will issue approximately 275 new regulations under the statutes it implements. 4/

Jan 1, 1988

By E. L. Bohnet

The purpose of this paper is to translate a mining company's "Corporate Objectives" into usable and practical guidelines for long term mine design and production scheduling. These guidelines are required to ensure that both operating and development properties are designed and economically ranked on the same basis, and with the "current" Corporate Objectives in mind. Secondly, if both management and mining engineers have a better understanding of the cause and effect of corporate policies, then penalties and risks associated with various Corporate Objectives can be put into better perspective for management. Corporate Objectives, relative to usable guidelines for either short and/or long term mine planning, could be defined as one or more of the following four objectives: 1) Maximize the recovery of the economic portion of the defined geologic resources, and hence, maximize total non-discounted project cash flows and profits (most common approach in mine design), 2) Maximize the Net Present Value (NPV) of the after-tax cash flows from each existing or proposed project, either on an individual basis or in concert with other projects, including downstream processing facilities (primary method used to judge relative investment merit of a proposed development or operating concept), 3) Limit short and long term capital expenditures to a defined ceiling, 4) Maximize product output for the existing facilities in the short term, or conversely, keep commodity production at a constant level for a series of years.

Jan 1, 1994

By Katherine Hynard, Colin Eustace

Suboptimal decisions introduced during the mine planning process are generally a consequence of both a myopic view of planning objectives as well as time and resources available to convert longer-term plans into execution plans. Erosion of strategic mine plan value in conversion to execution plans is likely to amount to billions of dollars each year. When integrated with operations data feeds, simulation and optimization tools can be used to preserve the value in the strategic mine plan. Optimization models are capable of both automating production of execution plans and improving performance. This reduces the manual burden of revising plans while improving alignment with long-term production objectives. Simulation models can also support the process of developing effective execution plans by providing forward visibility of mine operations performance. They can also be used to test the robustness of optimized execution plans and response to operational variability and disturbances.

May 1, 2025

By H. C. Verakis

Permanent ventilation controls such as stoppings, overcasts, and undercasts for use in coal mines are required to meet MSHA’s safety standards for fire endurance and flexural strength. Due to technological advances in materials and their design for use as ventilation controls, an engineering program was established to evaluate newer or “nontraditional” ventilation controls. The program is intended to assist manufacturers, enforcement personnel and mine operators in determining if “nontraditional” ventilation controls, for example plastic membrane construction and lightweight block, meet the prescribed safety standards. The program is presented with a description of required tests and examples of products evaluated.

Jan 1, 2003

By James N. Grassby

Metal production has traditionally been a cyclical industry. 1977 in the base metals industry has highlighted that fact with a steady decline in the market place for base metals. Corporate aggregate planning is based on good forecasting and when changing conditions make that forecasting inaccurate, alternate analysis of schedules must be accomplished quickly. The computer is the only medium powerful enough to answer management's questions within an acceptable time frame. Worldwide communications networks now make it possible for the many multinational mining companies to arrive at coordinated corporate production plans based on similar basic data from several producing divisions. The Ontario Div. of Inco Metals Co., a unit of Inco Ltd., encompassed during 1977 14 producing mines, 2 nonproducing mines, 1 nonproducing open pit, 5 flotation mills, I smelter, 2 nickel refineries, 1 copper refinery, and an iron ore recovery plant. Several new mines are under development. Mine production approximates 63 500 tpd (70,000 stpd) from some 1000 workplaces. The need for longrange mine planning and scheduling is obvious and until recently has been satisfied by manual methods. However, while manual methods are often quite practical for a small number of mines, or for mines with relatively short lives, or for mines with only one mining method, the situation in the Ontario Div. is too complex and long-term to allow effective, timely planning by such methods. In 1967, a year after the first computer was installed in the division, work was begun on the computerization of the more than 30,000 borehole logs kept in the mines exploration files with a view to speeding up the assessment of mineral resources. Also in 1967 one of the first substantial systems developed on the main business systems computer was the monthly scheduling of development and production for all mines. This system encompassed tons productions per workplace, feet development per workplace, auxiliary and service activities and the requisite labor for each of these. These two dates are mentioned to show that concurrently with the acquisition of computers in the division there was an early understanding of the importance of automating mine scheduling and planning and of the potential for effective and useful computerization of such activities. In 1970, a pilot program was developed in one of the mines containing a large number of workplaces (350) to schedule the production on a network basis. Varying degrees of interest were shown by the individual mine engineers based on the complexity of the production planning problem at each mine. In an evolutionary process, mines were added to the system as its value became obvious in terms of time saving, flexibility, and accuracy. In 1975, the central mine engineering department decided that the system should be extended to all mines so that a complete division-wide long-range scheduling system would be available upon which to base development and production planning. This system would use basic ore data, allow the addition of scheduling commands, and calculate a schedule for the life of the mine. Many reports could be produced for each mine and all-mine summaries would also be available. The significance of the system can be stated in one phrase-speed, accuracy, and flexibility. Whereas in the past a long-range all mines schedule might have been done once a year, taking from two to three months, now it can be done in a day. The chief mines engineer can incorporate changes in input data and external constraints and call for a "new look" at the long-range schedule to assist him and mines production management in their decision-making processes. Using previous manual methods this could not be done quickly enough to be useful.

Jan 1, 1979

By L. G. Wilson

In order to comply with time limitations imposed by this symposium, a very narrow but nonetheless interesting segment of the market has been chosen for discussion of the preparation of a tailor-made product to meet a specific need, and in view of the fact that the barite market is one of the oldest and one of the broadest non-metallic mineral markets in the world, it is necessary that we place this in perspective. Of a recent world annual production; (i.e., 1966 figures released last year in MINERALS YEARBOOK), of some four million tons, the United States consumed over 1/2 million tons, of which approximately 950,000 tons were produced domestically and approximately 700,000 tons were imported. Of this total, something approaching 90% was used for drilling-mud weighting, and of the balance, all but about 60,000 tone is consumed in the production of glass, barium chemicals, aggregates, and other minor uses; thus we are really taking a look at a very minute, however important, and very selective, portion of the total barite-market. The real meat of this paper, after eliminating all irrelevant uses of barite, and delineating the area of discussion, resolves itself into the approach to a favorable marketing area and a specific attack on that area. Cost, to the user, has been, patently, a function of distance, as the basic price of barite has varied very little over the years until recently, and freight rates have been the governing factor. Conversely, the seller of barytes must make concession in the plant price to compensate for distance, if he is to successfully compete.

Jan 1, 1969

By Richard B. Berg

Until its closure in 1999, the Antler was North America's only active chlorite mine. The mine is located 25 miles (40 km) southeast of Butte in the Silver Star district - an old Montana gold mining district. In 1975, two prospectors searching for talc re-examined a prospect showing a green, fine-grained mineral resembling talc. Following identification and testing of this magnesian chlorite (variety clinochlore), Cyprus Industrial Minerals began processing ore from this deposit in 1976. Chlorite veins ranging up to 30 feet (9 m) in thickness were formed by essentially complete replacement of Precambrian (Archean?) quartzofeldspathic gneiss. Chlorite replacement was controlled by near- vertical faults. These chlorite veins, typically surrounded by envelopes of sericitic alteration, were formed by the introduction of magnesium-rich hydrothermal fluids, probably related to the Proterozoic talc-forming event in southwestern Montana. Luzenac America, Inc. acquired Cyprus' talc operations in 1992, and continued to mine this deposit until the ore body was mined out in March 1999, and the mine was reclaimed. Total sorted ore production from this deposit is about 250,000 short tons (st) (227,000 metric tons [mt]). Chlorite from this deposit was primarily used in ceramic and paint applications.

Jan 1, 2001

By G. Van Weert

Oxygen transfer from dispersed air in agitated slurries represents an important unit operation in the minerals processing industry. Gold leaching, iron precipitation and especially bio-oxidation come readily to mind. However, little engineering information is available on the variations between impeller types on such O2 transfer. Engineering literature on the subject, i.e. information which relates slurry density and energy input to O2 transfer, is reviewed and compared to current experimental work. The latter was carried out with minus 50 micron sand/water slurries in a 64 I laboratory tank of standard proportions, equipped with a variable speed drive with torque meter. A standard Rushton turbine and a specifically sized A315 were compared. Results confirm an increasing impairment of O2 transfer with increasing slurry density for both impellers. The volumetric mass transfer coefficient, k,a, in a 10 vol. % slurry shows a decrease of 30% compared to the k,a in water. At 20 vol. % sand this decrease is near 50 %, depending somewhat on superficial gas velocities. Power efficiency, i.e. the kg O2/kWh, decreases about 25 % more rapidly for the Rushton turbine than for the A315 with the addition of sand. However, for equivalent O2 transfer the Rushton turbine was more efficient in this work. Experimental results are presented and their significance for slurry bio-oxidation discussed.

Jan 1, 1996