Search Documents

By Joel K. Waterland

GENERAL DESCRIPTION Open cut-and-fill stoping for many years was prob¬ably the most widely used mining method in under¬ground metal mines. Then for a time this method was largely supplanted by the blasthole stope. It again be¬came popular as many mines reached depths or grades where methods requiring large open voids to remain open for extended periods of time became unsuccessful, often as a result of excessive dilution. The open cut-and-fill method is very flexible and is readily adaptable to almost any ore body. The standard application requires that a slice of ore usually 2.4 to 3 m (8 to 10 ft) thick be removed from the back of the stope, and as the ore is taken down, the back is dressed and rockbolted. After the back is secured, the broken rock is removed through rock passes to the level below. When the rock has been removed, the rock passes are extended upward the height of the ore removed, the stope is backfilled, and another cycle is mined. This method is best employed in plunging ore bod¬ies with considerable vertical extent, ore areas that re¬quire selective mining, ore areas where weak wall con¬ditions exist, and ore bodies that have an ore value that will carry this relatively expensive mining method. Blast¬hole stoping, shrinkage stoping, and other mining meth¬ods that do not employ rock passes in a stope are not efficient in plunging or flatly dipping ore bodies because the footwall makes ore removal quite difficult. Since mining is accomplished by taking down slices of the back, only small areas of the wall rock are exposed at any one time, and these only for short periods. Due to limited back height, areas of uneconomic rock may be left in place, or they may be mined and the material gobbed in the stope. Because the miners in the stope must work under freshly blasted areas, the amount of ground control is usually great. The volume of rock that is broken during one section of mining is relatively small and the amount of nonproductive work required is high. This results in limited productivity for the scope and, be¬cause of the nonproductive work that must be done on a regular basis, the production from the stope may be quite cyclical. SUITABLE ORE BODIES The open cut-and-fill method may be adapted to al¬most any type of ore body with a relatively high vertical extent. The ore body must be accessible at both top and bottom as well as at regular intervals throughout its vertical extent. Although adaptable to most ore bodies, the method is probably best employed where the ore has poor con¬tinuity and where most types of bulk mining would pro¬duce excessive dilution. In areas of poor ore continuity, the capability of continuous and extensive sampling dur¬ing the mining of each cycle makes this method very desirable. This capability also minimizes the amount of evaluation sampling that must be done before mining is started. Because of the extractive system used, the size and shape of the stope may be as readily changed as the sampling mandates. Probably the only ore characteristic demanded is that the ore has strength enough to be sup¬ported through the use of rockbolts or cable bolts dur¬ing the mining and backfilling cycles. Good planning, systematic sampling, and careful supervision will pro¬duce a product with less dilution than any other open stoping method. PLANNING Evaluation Planning Once it has been decided that the open cut-and-fill method would be the most efficient for mining a par¬ticular ore body, the next considerations would probably be the availability of an economical backfill material and the selection of an efficient transport system for this material. Although hydraulically transported mill tail¬ings are the most widely used product, this is not always practical due to mill location or the quality of the tailings. In such cases, backfilling may be used. The type of backfill and the type of equipment used will determine if a floor or capping on the backfill is required to minimize dilution during ore removal. The early selection of rock removal equipment is im¬portant since equipment usually determines the amount of development work required to bring a stope into pro¬duction and the size of the openings needed. The size and continuity of the ore body will usually determine the type of loading equipment. The use of slushers or load¬haul-dump (LHD) equipment captive in the stopes will minimize the amount of development. If the ore con¬tinuity is such that a ramp system for extraction can be used, the cost of development will be increased but the flexibility of continuous mining will minimize the cycli¬cal nature of the production. The height of the mining section usually is deter¬mined by the strength of the wall rock and the amount of back bolting required. Once this has been decided, the appropriate drilling equipment can be chosen. The number and sizes of the rock passes employed depends upon the type and size of the extractive equipment and the type of backfill that is to be used. Since the miners must enter and leave the stope each shift, the level inter¬val is usually maintained at approximately 45 m (150 ft). Access from the level above into the stope must be main¬tained at all times. The employees perform all the work in the stope and adequate ventilation must be provided. Stope Planning Due to the flexibility of the method and the vari¬ability of the ore zones, layout is usually done on a stope basis. In areas where continuity is a problem, the size of the stope is usually determined by the boundary of the ore (with all of the ore within that boundary being removed). In areas of good continuity where ramps are to be used, the length of the stope may be determined by the length of time each of the cycles (preparation, back¬fill, mining, and ore extraction) requires. The ramp work is then laid out so that access to the various parts

Jan 1, 1982

By Tommy B. Thompson

The Cripple Creek diatreme-intrusive complex is known primarily for its vein telluride-gold ores. It is also known for the great vertical range of its major veins - >990 m (>3250 ft). Not as well-documented, however, are the ores dispersed into the wallrocks adjacent to veins, the ores associated with hydrothermal and tectonic breccias, or mineralized zones within fluvial, lacustrine and volcaniclastic rocks de- posited within the diatreme complex. The ore-gangue minerals were precipitated from oxidized, alkaline fluids that yielded an abundance of carbonate, sulfate and oxide minerals along with minor base metal sulfides and precious metal tellurides. Wallrock alteration is limited adjacent to veins and is more extensive within hydrothermal and tectonic breccias. Cripple Creek background The Cripple Creek district has a spectacular production history. More than 653 t (21 million oz) of gold were recovered between 1891 and 1959. Early published accounts documented the principal production from narrow- sheeted vein systems (Cross and Penrose, 1895; Lindgren and Ransome, 1906; Loughlin, 1927; Loughlin and Koschmann, 1935). Production also came from spectacular open-space fillings within the Cresson diatreme, also known as the Cresson “blow-out” (Patton, 1917; Patton and Wolf, 1915). Beginning in the mid- l96Os, more modern studies were initiated by the US Geological Survey (USGS) (Gott et al. , 1967, 1969; Kleinkopf et al., 1970) and by universities (Lane, 1976: Dwelley, 1984; Trippel, 1985; Thompson et al., 1985; Saunders, 1986; Birmingham, 1987; Eriksson, 1987; Nelson, 1989; Wood, 1990; Seibel, 1991).

Jan 1, 1992

By John Murray, Daniel Ebin, Robert Gould

The Atlanta Plane Train project at Hartsfield-Jackson Atlanta International Airport employed the progressive design-build approach. This provided opportunities for collaboration between the design-builder, design engineer, and owner and the implementation of innovative design and construction approaches. The innovations have reduced risks, allowed for adjustments during design to accommodate new challenges, and provided open-book cost and schedule evaluations. The progressive design-build approach has also allowed for pricing of work to occur in phases—capturing the design/construction challenges as the project evolves and when they are more clearly defined. While this has allowed for pricing to be performed with better project understanding and therefore less contingency, the associated time frame for approvals has required careful consideration to avoid impacts to the schedule. This paper discusses the benefits and challenges of the progressive design-build approach.

Dec 1, 2022

By Eugene L. Foster, Gilbert L. Butler

The successful demonstration of a precast segmented concrete liner in the Lexington Market Section of the Baltimore Regional Rapid Transit System (BRRTS) is an important step forward in our continuing efforts to control tunneling costs in the USA. In addition to its contribution to specific savings in future tunnels, this demonstration project has taught other lessons about the U.S. tunneling industry and about the process of "mainlining" new and improved technology into that industry. This paper will present an overview of the Lexington Market Demonstration Project from its beginnings to the present time. In addition, it will discuss other implications which have an important bearing on the extent to which tunnels will be used in future transportation systems in the USA. THE HISTORY Precast segmented concrete tunnel liners are not new. An unbolted version was reportedly used in New York City in the 1930's. The modern bolted configuration has been in use in foreign countries for more than 15 years. Indeed, consideration of the use of precast bolted segments below the water table in the USA dates back to the BART system in San Francisco in the 1960's. At that time, they were evaluated and it was concluded that the state of the art would not allow segments to be precast to the required tolerances. A secondary grinding operation would be required if water-tightness was to be assured, making them economically non-competitive with steel. Based

Jan 1, 1981

By David A. Rice, Scott A. Shuey, William K. Tolley

The U.S. Bureau of Mines (USBM) is developing new dewatering technology to permit the recycling of iron values contained in wet steel plant sludges. In laboratory tests, Q-BOP fume sludge was dewatered to 12% moisture by displacing water with acetone in a plate-and-frame pressure filter. Acetone is reclaimed through distillation at lower cost than conventional thermal drying of the sludge. The projected additional energy requirement for acetone treatment of the sludge, including acetone recovery, is $5 to $7 per dry ton.

Jan 1, 1995

By Haia Roffman, Amiram Roffman

A gas company operated more than 100 distribution stations. Mercury filled manometers were used for years in these stations to measure the flow of natural gas through the system. Use and handling of these manometers resulted in mercury spills and ground contamination. To assess the human health and environmental effects of these spills and the need of remediation, it was important to determine mercury specific species present and their concentrations. Soil samples were analyzed for total mercury, methyl mercury, inorganic mercury and elemental mercury. These analyses served as important input in the risk assessment performed for these stations.

Jan 1, 1998

By Nigel Fung, J. D. Humphrey, R. H. Oats, J. H. Ingle

Production dozing of cast material is a cost effective method of improving dragline or mobile equipment overburden removal. Yet dozer productivity is reduced during the part of the process that requires the dozers to cut material away from the highwall. One solution is to use a hydraulic excavator to remove this material and throw it into a windrow for the dozers. By freeing up the dozers for more productive work the overall system productivity increases 25% and cost per yard is reduced by up to 10%. Dozer fleet sizing can be determined to match a specific production schedule or can be sized to balance with an excavator’s production.

Jan 1, 2004

By Fred H. Lightner

The feasibility evaluation of the Borealis project of Houston International Minerals Corporation (HIMCO) was initiated in October of 1980. The operation of the Borealis Mine and heap leaching plant began in late 1981. In order to achieve the rapid development schedule several items were necessary: 1) Pre-planning of environmental requirements and early study of key issues. 2) Adoption of conservative design criteria. 3) Coordination and cooperation between HIMCO and regulatory agencies. 4) Adoption of specialized engineering and construction procedures. 5) Careful evaluation of owner project management philosophy.

Jan 1, 1982

By William E. Foreman

The results of the electrokinetic study of the activation of quartz by divalent cations showed that the charge reversal was related to the point at which the cation hydrolyzed. The reversal was not due to the presence of solid hydroxide at the surface of the quartz but due to the charged ions in the solutions. The charge reversal for beryllium at a log molar concentration of 1x10-4 was observed at pH 5 and 9. The quartz was positively charged between a pH reading of 5 to 10. Magnesium at the same log molar concentration did not show a charge reversal from pH 2 to 12. The probable cause of the charge reversal was due to the ionized Be3 (OH)3+3 or Mg (OH)+ . Variations in the electrokinetics of quartz were minimized by heating the sample to 300° C.

Jan 1, 1968

By A. Kaczmarek

As the mining industry is enjoying a much needed and long awaited increase in demand for natural resources, consolidations in both the mining and mining service industries and a generational departure of experienced industry professionals is challenging today’s mining companies, not only in maintaining their existing operations, but also in securing qualified resources for developing new projects. These challenges are compounded for junior mining companies, oftentimes lacking in operating properties to draw from for experienced professionals and having to compete with the majors’ “mega-projects” for experienced project personnel from the reduced ranks of engineering companies. This paper discusses some strategies developed by Anatolia Minerals Development Limited in developing its Çöpler Gold Project in central Turkey.

Jan 1, 2006

By Peter P. Harvey

The Nonel Primadet is a non-electric blasting initiation device. The system incorporates the safety advantages of a cap and fuse system with the precision blasting afforded by electrical blasting caps. Each unit is made up of a delay blasting cap factory-crimped to a Nonel® shock tube lead line. The delay elements in the blasting caps are manufactured in both millisecond and long period series. There are 16 periods available in both series - period 0 through period 15. The units are manufactured in 12', 16', and 20' lead lengths. The hollow shock tube is made of surlyn plastic and it is coated on the inside with a reactive material. The powder train has a density of only 1/10 grain per linear foot of tube. A typical blast round is timed precisely the same way it would be with electrical caps. After the round has been timed and loaded, the tube leads are gathered in convenient bunches and tied into a detonating cord trunkline. The Nonel® tube bunches are initiated by the output of an 18 grain per foot detonating cord trunkline. Once initiated, the Nonel® shock tube will reliably propagate at 1800 meters per second. The energy from this shock front initiates the delay elements in each delay cap. The shock tube is inert to electrical energies, including; stray current from AC/DC power sources, as well as, electrostatic discharges. The tube is also inert to initiation by impact. The system has proven to be particularly advantageous in both tunnel and shaft blasting applications. The major advantages in using the Nonel® system in this type of work are: 1) faster and easier tie-in techniques through the use of bunch-blasting. 2) electrical power can be left on during loading and tying-in. a. electrical lights can be turned on at the working face - better lighting facilitates loading and tying-in. b. electrical pumps can continue to function throughout loading and priming procedures (this is particularly advantageous in shaft work with water problems). 3) down-time due to approaching electrical storms is minimized. 4) increased overall efficiency in the blasting cycle: a. it is easier to train a man in the proper use of the system. b. fewer missed holes per round. c. less time required for tie-in. 5) safety-advantage--The system is not susceptible to involuntary initiation from extraneous electrical energies.

Jan 1, 1979

By I. Tsolas

Sustainable development is becoming increasingly more important for the mining industry and therefore mining companies should be able to measure their progress towards sustainability. Greek Public Power Corporation (PPC) S.A. is a company which produces lignite in open cast mines in Western Macedonia and in Peloponnesos. The present paper uses operational data kindly offered by PPC S.A. to derive sustainability indicators by means of Data Envelopment Analysis for three large scale lignite open cast mines of PPC (i.e. Main Field, Kardia Field and South Field mines). It also examines three environmental parameters related to the contribution of these mines to sustainable development; namely, the annually produced volume of waste masses, the annually produced quantity of ash from the lignite combustion and the annual volume of pumped water. The calculated sustainability indicators were keeping constantly better during the last years of the different periods for each one of mines studied here, showing that the mines met their goals from both economic and environmental aspects during the last years of their operational periods studied. The contribution of open cast lignite mines studied here to sustainable development can be monitored by the derived indicators analyzing annual mine operational data. The derived indicators can serve as tools to detect where improvements can be made, though another potential use of these indicators can also be during the preparation of feasibility studies or environmental impact studies using necessary benchmarking data.

Jan 1, 2007

By K. Häge

"Die Nachhaltigkeit der Braunkohlengewinnung in der öffentlichen Wahrnehmung wird nur weiter erfolgreich kommuniziert werden können, wenn durch konkretes Handeln glaubhaft gezeigt wird, dass die offenen Fragen fair und solide beantwortet werden. Dazu gehören insbesondere die neue innovative technische Lösung sowie das sensible Interessenmanagement. Die Braunkohlenindustrie hat gelernt, dass Offenheit und nicht zuletzt das beständige Bemühen um den Meinungsaustausch mit ihrem Umfeld wichtige Elemente sind. Der in Jahrzehnten erworbene Schatz an Glaubwürdig-keit ist eine Basis, auf der die Braunkohlenindustrie ihre Zukunft gestalten kann. Darüber hinaus sind politische Rahmenvorgaben erforderlich. Das öffentliche Interesse an einer sicheren und preiswerten Energieversorgung unter Einschluss der Braunkohle ist unverzichtbar. In diesem Kon-text kann dann die Braunkohle die an sie gerichteten Fragen der Ökonomie, der Ökologie und der Sozialverträglichkeit auch mit Hilfe von Indikatoren beantworten.ABSTRACTThe discussion of the sustainability of lignite mining can only be continued successfully if the indus-try acts in a practical manner and demonstrates trustworthiness by responding fairly and reliably to open questions. This includes new and innovative technical solutions as well as the sensitive management of interests. The lignite industry has learned that openness and the constant effort to exchange viewpoints within their environment are all essential elements. The credibility that has been gained over the decades is the foundation on which the lignite industry can build its future. Beyond that a framework of political guidelines is necessary. Public interest in a secure and inex-pensive energy supply that also includes lignite is indispensable. In this context, the lignite industry will then be able to answer the questions which are directed at them and concern the economy, ecology, and social tolerability also by indicators."

Jan 1, 2005

By Roy Norcross

For the past few years Caro's acid has been used for the treatment of cyanide containing slurry effluents, providing a feasible alter­ naive to other slurry treatment processes including !NCO SO2 / Arr and ferrous sulfate. Presently, mines using Caro's acid gen­erate their own Caro's acid onsite making a relatively low quali­ty product. It was at this point where we, at Degussa Corporation, decided to focus our efforts on engineering a Caro's acid genera­tor capable of cost effectively producing a high quality Caro's acid solution, thus reducing operating costs significantly. Caro's acid or peroxymonosulfuric acid is not a new chem­ical nor is it new to Degussa. The product was named after Heinrich Caro (1834-1910), a German chemist who first described its synthesis and its oxidizing properties in 1898. Degussa has been producing the potassium salt of Caro's acid as the triple salt, 2KHSO5 - 2KHSO4 - K2SO4, called Caroat®, for over 30 years. Caroat® is used for household and denture cleansers, as a bleaching agent in dish washing detergents, in printed circuit board etching and for cyanide destruction in the plating industry. From our experience in producing Caroat® Degussa developed its new Caro's acid based DegOX™ technology for the treat­ment of cyanide containing effluents from gold and silver mines.

Jan 1, 1996

One of the most challenging and ambitious dump rehabilitation projects in South Africa’s mining industry is being carried out at Greenside Colliery’s smoldering coal dump, which lies adjacent to the N 12 Johannesburg-Witbank highway. Greenside Colliery is the largest coal mine in the Gold Fields Group. It began operation in 1946, the year in which the burning dump had its origins. Today, Gold Fields plans to spend R16 million (about $USS8 million) to encapsulate the dump, bringing it into compliance with South Africa’s Mining Environmental Management Programme, according to Martin Hamer, engineering manager of the Greenside Colliery. The improved environmental management approach will result in reduced sulfur dioxide gas, smoke and dust emisson into the air and an enhanced aesthetic appearance of the dump from the N 12 highway. The objectives of the project are to place and compact coal discard to within the National Institute of Coal Research specifications in order to prevent spontaneous combustion, and to preserve as an asset the coal portion of the discard.

Jan 1, 1994

By T. Deschaines

Raman Spectroscopy has become increasingly popular as a method to rapidly identify and characterize minerals, gem stones and other inorganic materials. Raman spectroscopy provides valuable information about the chemical bonds and structure of materials. In fact, the peak locations and intensities observed in a Raman spectrum can often be used to confirm the presence or absence of particular species in a sample. Some modern Raman spectrometers have been designed to analyze samples less than a micron in size while others are designed to rapidly screen bulk material with no sample preparation. Recent advances in software and automated instrument control have greatly reduced the complexity of Raman spectral analysis and provide an easy-to-use tool for analyzing minerals. We will describe the application of several multivariate statistical analysis techniques that have been developed to make use of the spectral libraries. In these techniques the spectrum is treated as a vector and sophisticated mathematical techniques are used to determine which spectral representations in the reference library best match the spectrum from the sample. The DXR Raman microscope was used to 1) Identify minerals by spectral searching, 2) Identifying several species in a sample using multi-component analysis 3) Mapping different species in an aggregate sample and 4) identifying inclusions in a sample.

Jan 1, 2010

By James Y. Oldshue, Paul M. Kubera

Most coillillercial processing applications employing mixers in various types of slurry systems are continuous flow. These applications may also be multiple stage, with the stage number varying anywhere from two or three to ten or more. Two questions that usually come up at the beginning of any proposed pilot plant study are (1) can the pilot plant unit be operated batch-wise, and the results extrapolated both on the basis of scale and fluid motion to the full-scale tank which will be continuous-flow (and probably multi-stage), or (2) does the pilot plant need to be operated in a continuous-flow fashion, and if so, does the exact number of tanks/stages that are proposed for the plant need to be used in the pilot plant? We will consider these possibilities in sequence and present the principles involved in running some of the various pilot-plant arrangements.

Jan 1, 1992

By S. C. Gambrell

The practice of roof bolting in world-wide mining activities is very well known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Discussions of the mechanics involved usually originate with actual experience gained in the use of roof bolts. The use of roof bolting in mines has grown dramatically during the period after World War II. Other scientific techniques have emerged in mining research in the same period. Included in these techniques is the study of rock mechanics, which has now developed into an impressive research effort. Various means of analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that could be easily analyzed. Because of the inherent nature of rock, direct research methods frequently are not certain to provide satisfactory results, whereas indirect methods must idealize a given set of conditions in order to be useful. One of the indirect research methods is the photoelastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various configurations (1,2,3,4,5). Much of the theory used now in the design of underground openings is based on photoelastic evaluation. Unless rigorously applied, how- ever, the photoelastic technique is at best a qualitative means of evaluation. It is useful, however, for unusual examples which can be more or less easily analyzed to obtain the overall state of stress which could not be determined by other means. Little work has been done in the photoelastic analysis of rock bolting, mainly because direct research techniques have proven useful.

Jan 1, 1970

By D. L. Stevens

Following an in-depth scenario and strategic-planning exercise in 1997, Noranda's mine production goal was set at 500 kt/a (550,000 stpy) of both copper and zinc metal in five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in Noranda's program. The following steps were taken: the exploration and business development groups were combined, teams were formed to search for and respond to opportunity; geologists were coached to become more business minded and engineers were coached to become more optimistic; the company went global; clear thresholds were set, marginal properties were farmed out and other properties were fast tracked; reconnaissance exploration was focussed where there was a clear competitive advantage; and Noranda became a "flexible" partner to juniors and seniors. Is it working? A number of successes, near successes and outright failures are discussed. The main result is a much higher rate of opportunity flux, which is essential for success in the mining industry.

Jan 1, 2000

By J. Mersch Ward

Homestake Mining Company has identified a significant native sulfur resource at its Cinnabar Canyon prospect in Mono County, California. Elemental sulfur occurs as replacements, fracture coatings and breccia fillings in a thick sequence of Miocene-Pliocene intermediate volcanic rocks. The deposit extends along a northwest trending regional fault and measures approximately 900' in width, at least 1800' in length, and has a thickness in excess of 200'. The deposit lies approximately 150' below the surface and is covered by a silicified cap of volcaniclastic strata. The deposit has been delineated by rotary and core drilling. Utilizing a grade cutoff of 5% elemental sulfur, the delineated deposit has a probablelpossible resource of 16.1 million tons of ore averaging 17.9% elemental sulfur containing 2.57 million long tons sulfur. Assay grades within the resource area range up to 40% sulfur over a 40-foot intercept.

Jan 1, 1992