Search Documents

By S. Slottee

The disposal of plant tailings in a safe and environmentally acceptable manner has taken on increased importance throughout the world, across all types of mineral beneficiation plants. In the U.S. plant life span, expansions and new plants in the current robust mineral markets are faced with environmental pressures to minimize the use of land for disposal by maximizing existing tailings pond capacity. The combination of many drivers from economic to environmental have brought paste thickeners into the coal industry (PasteThick 2007) Thickening tailings to a more concentrated slurry is a common step in the disposal flow sheet. Thickening to a non-settling ?paste?, also called ?thickened tails? or ?tailings stacking?, is a relatively recent development. This paper describes the paste thickener as an alternative for dewatering a fine coal refuse (tailings) stream for deposit as a paste. Initial operating results of the paste thickener are discussed.

Jan 1, 2008

By L. M. Chan, D. H. Carlson, J. H. Johnson

This paper discusses laboratory evaluation of a tailpipe emissions measurement apparatus (EMA) developed by Michigan Technological University (MTU) under contract to the Bureau of Mines. The apparatus dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, C02, NO and NO2 at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory grade instruments. During the preliminary laboratory evaluation concentrations of DPM, CO and CO2 were measured. The concentrations of CO and CO2 measured by the EMA were usually within ±14 pct of laboratory-measured values for CO and ±20 pct for CO2. EMA DPM concentrations correlated well (r = 0.96) with the laboratory values, but were 29 pct lower on average. The CO and C02 differences were observed to be related to the method of calculating the EMAs' dilution ratio and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminery analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 1991

By Stefan Medel

As a pioneer Herrenknecht started in 2018 to automate the production of tunnel lining segments. Since then, many automation processes became state of the art. Robots cleaning and oiling the moulds, hydraulic units opening and closing them fully independently. Artificial Intelligence (AI) controls the works and ensures the quality requirements. Data management has become a massive tool from a simple data collector towards a control and optimization tool. Sensors controlling concrete maturity and supporting the precast team to optimize the concrete mix. These state of the art and new innovations will be presented in this paper.

Jun 23, 2024

By S. K. Mishra, S. B. Kanungo

Because conventional (physical) methods of ore dressing are not suitable for reducing the phosphorus contents of high-phosphorous manganese ores from Andhra Pradesh (AP) and the adjoining area in southern Orissa, India, the adoption of chemical methods becomes imperative. An attempt was therefore made to reduce the phosphorus content of partially beneficiated manganese ores from AP by roasting with sodium carbonate and then leaching with hot water. However, due to the higher phosphorus contents of the manganese ores from Nishikhal mines in southern Orissa, and because of their apparent resistance to dephosphorization by roasting with Na2CO3 alone, a mixture of Na2CO3 and NaCl was found to be necessary to reduce the phosphorus content to below 0.15%. Free-energy calculations at 700°C and above indicated that Na2CO3 (or Na2O as the active component) is a more active reagent than NaCl. Various process parameters, such as the temperature and time of roasting, the amount of sodium carbonate and the temperature and time of leaching, were studied to arrive at the optimum conditions for dephosphorization.

Jan 1, 2000

By J. Hanna, H. R. Gonzalez

Discussion by N.L. Hargett Dear Dr. Hanna: As discussed in our phone conversation, we are enclosing a suggested revision to the paper, "Application of Bentonitic Clays in Suspension Fertilizer Formulations," published in MINERAL & METALLURGICAL PROCESSING, May 1990. The revision will replace the second paragraph in the article. The reason for the revision is that suspensions have decreased in market share since 1984 and at present comprise an estimated 25% to 30% of fluid mixtures. This represents 6% to 7% of all fluids and only 2% to 3% percent of all fertilizers. Based on national surveys conducted by the Association of American Plant Food Control Officials (AAPFCO), suspensions comprised an estimated 25% of all fluid mixtures in 1974, 33% in 1976, 35% in 1980, 40% in 1984, and 36% in 1988. Revision to "Application of Bentonitic Clays in Suspension Fertilizer Formulations." Suspension fertilizers are an important segment of the fertilizer industry in the United States. Suspensions allow higher concentrations of nutrients (N, P2O5, K2O) than clear liquid solution fertilizers. K20 content of solutions is limited to about 10%, while suspensions can contain more than 30% K2O. Suspensions can tolerate greater variations in temperature than solutions. In suspensions, if crystallization occurs, the crystals can remain suspended in a clay jell instead of settling as they would in solutions. Solubility is not a limiting factor in suspensions, since complete solubility of phosphate is not required. This allows a wider range of phosphate materials to be used. Also, materials commonly used in formulating suspensions are less expensive and more widely available than those for clear liquids (Getsiner et al., 1984).

Jan 1, 1992

By R. Pandey, G. Elie, E. Sarver

Respirable crystalline silica (RCS) is generally considered the most hazardous constituent of coal mine dust, and a new federal rule is expected to further limit exposures in U.S. mines. For regulatory purposes, RCS is monitored by collecting filter samples, which are analyzed for quartz (the predominant form of RCS in coal mines). The analysis is done using Fourier transform infrared spectroscopy (FTIR) in a centralized laboratory. To enable more timely results, National Institute for Occupational Safety and Health (NIOSH) mining researchers developed a directon- filter (DOF) FTIR analysis method and free FAST software that can be used in the field. For samples collected under specific conditions, FAST processes the FTIR spectral data to determine quartz mass. While the DOF FTIR method is not approved for regulatory RCS monitoring, it could be useful for engineering purposes, such as to evaluate mining parameters or new dust controls. This field study demonstrates how the method, including FAST, can be applied using low-cost, widely available sampling components. It further demonstrates how quartz percentage can be estimated in the field, by pairing a continuous personal dust monitor with a filter sampler.

Jun 1, 2025

By Jeong-Heum Kim, Jan M. Mutmansky

The primary purpose of the research summarized in this paper was to experimentally investigate the performance of numerous mine ventilation network iterative solution procedures under controlled conditions to determine which procedures were most favorable in terms of number of iterations and total computational speed. The solution methods investigated included: (1) the Newton-Raphson method, (2) the Hardy Cross method, (3) the linear theory method, and (4) the second-order approximation method. The first three of these methods have been widely used while the fourth was formulated by the authors to investigate its potential for ventilation network computation. In addition to the four solution procedures, three methods for selecting the branches in the meshes and three methods for ordering the meshes for computational purposes were also studied during the investigation. As a result of these various options, a total of 36 combinations of solution methods, mesh selection procedures, and mesh ordering schemes were studied. To investigate the performance characteristics of these combinations, an identical set of 180 randomly chosen ventilation networks was used in sets of 30 networks at six different levels of complexity. Here, the level of complexity is defined as a function of the size (number of branches) and the density (number of nodes compared with the number of branches) of the network. To eliminate variations in the solution times due to differences arising from the fans, a single fan with a fixed characteristic was utilized in all the experiments. This paper will deal only with the results for the four iterative methods used to achieve solutions to the mine ventilation networks. The minimum-resistance spanning tree method for mesh selection and random mesh ordering was used throughout the analysis. The conclusions will be based upon a detailed accounting of the efficiency of each method using the total time to achieve a solution to each problem and averaged over the total problem set. However, the number of iterations and the time to complete each iteration will be studied in order to better understand the solution procedures.

Jan 1, 1991

By F. Allen Meek

The Upshur Complex of Island Creek Coal Corp. consists of approximatly 35.000 acres of both surface and deep mine researves located in Upshur County West Virginia. The principle seams on the researve are the Middle and Lower Kittanning. Other mining in the area during the late 1960's and early 1970's produced surface mines that exhibited severely acidic drainage characteristics both during the mining phase, and after reclamation was completed. The Buckhannon River, the principal drainage for the area, is a high quality, lightly buffered stream, that is periodically stocked with trout. Because past mining had caused post mining acidic discharges and the Buckhannon River was a valuable recreational resource, mining permits for the area were put on hold by regulatory authorities, until solutions to the acid mine drainage questions could be addressed. In 1978, the director of the West Virginia Department of Natural Resources appointed a Task Force consisting of Industry, Regulatory. and Academlc participants. This Task Force was charged with gathering information and evaluating field procedures used during mining to prevent acidic mine drainage. In 1979, the group published a document titled "Suggested Guidelines for Mining in Potentially Acid Producing Overburdens" which summarized material handling and mining procedures that could be employed to help prevent the occurrence of post mining acid mine drainage. In 1982, a Technical Advisory Committee was appointed consisting of well known researchers in the field of acid mine drainage prediction and prevention. The group was charged with the task of conducting research in the field of acid mine drainage prevention. Mining conducted at the Upshur Complex between 1979 and 1986 employed various acid mine drainage preventative techniques recommended in the suggested guidelines manual and techniques concurrently being researched by the Technical Advisory Committee. Costs for the various techniques were documented and the resulting post-mining water monitored. The results of these evaluations are used by Island Creek in the planning of future mining operations in potentially acid prodcuing environments

Jan 1, 1991

By Paul M. Keyser, Donald G. Foot, Jeffrey D. Mckay

In the past 30 years, there have been tremendous advancements in the uses and applications of column flotation. From their first use as final cleaners that could produce excellent grades at the cost of recoveries, columns are now being used in every stage of the flotation circuit as well as is SX-EW. Columns as roughers, final scavengers and even at the end of CIL circuits, are finding their way into the marketplace. Operational results of these new uses are presented. INTRODUCTION Flotation columns have been in use since the early 1950's in the U.S. (Hollingsworth, 1952) and the early 1960's in Canada (Trembley, Boutin, Wheeler, 1963). Application of column flotation has been somewhat diverse. In the early years, columns were used predominately for molybdenum cleaning in Canada and for phosphate flotation in the United States. Unfortunately, results met with skepticism and disdain as the columns were hard to operate, temperamental and although producing high grades, could not achieve acceptable recoveries. Since the inception of column flotation technology, the degree of knowledge for design and operation of columns has vastly improved. Despite improvements in the technology, there is still some reluctance by mineral producers to investigate the use of column flotation cells for processing stages other than cleaner flotation. This characterization is in part due to the proven advantage of flotation columns in reducing gangue entrainment in the froth product which results in higher grade products and/or fewer processing stages. Also, during the development of column technology, different types of spargers have been used with varying degrees of success. Furthermore, the general knowledge base of parameters affecting column flotation design and operation have advanced tremendously. Inefficient, or primitive, sparger design, coupled with the lack of column design and operating knowledge and experience, resulted in poor metallurgical and mechanical performance in many cases. Unfortunately, this lack of knowledge caused many column installations to be characterized as failures. The industry felt that columns could not achieve high recoveries, especially when dealing with coarse particles. Therefore, columns were characterized as cleaners, where low recoveries could be tolerated as recirculating loads rather than direct losses and froth cleaning advantages of the quiescent column flotation regime could be realized. Fortunately for the minerals industry, some producers have stood at the forefront of technology and allowed the column to be utilized for new applications. In the last decade, column flotation applications have expanded to virtually every mineral system and plant location throughout the world. The expanded application of columns has generated a new wave of interest for processing various streams. One of the most notable is in the use of columns as rougher cells. This is of particular interest to "green-field" plants and plants where expansions are taking place. Here, metallurgical superiority can be combined with maximum capital and operating cost advantages for a rapid return on investment. The superior results experienced to date, have generated a cohesive vision of the future in mineral processing where flotation columns function as single stage primary separation devices (roughers) with a single stage cleaner, if necessary. The advantages of column flotation go far beyond their original uses. We now have seen columns used as final tail scavengers, in SX-EW plants and even at the end of CIL circuits. Some of these cases will be reviewed. CASE STUDIES In an attempt to show the diversification of column flotation to many facets of the mineral processing plant, a variety of case studies will be discussed. Some of these were designed by the authors while others have been provided by plant sources. It is important to note that in each successful case, the columns were designed using the author's design and scale-up approach. This method assures that the columns are designed correctly for their particular application. For successful

Jan 1, 1993

By David J. Brown, Richard C. Fountain, Marc V. Hurst

The Central Florida Phosphate District, one of the most productive phosphate districts in the world, has been mined principally within Polk and Hillsborough Counties, Florida. Recent development is extending the district southward into Hardee, Manatee, and DeSoto Counties. This area is known as the Southern Extension. The combined area of these two phosphate-bearing areas encompasses about 2,000 square miles. Structurally, the district and its Southern Extension lie at the southern end of the Ocala Arch and are flanked by the Hillsborough High to the northwest. South of this area is the South Florida Embayment. The Osceola Low lies to the east. The phosphorite within the Central Florida Phosphate District generally dips very gently (<0.1°) to the south. The boundaries of the central Florida Phosphate District are generally defined by thinning of the phosphorite due the adjacent structurally high areas to the north, west, and east, and by increased clay, CaO, and MgO content reflecting lithologic differences to the east and south. The Bone Valley Member of the Peace River Formation and reworked sediments of more recent age were the primary ore-bearing horizon in the Polk-Hillsborough County area. As those reserves are depleted, the less desirable phosphorites of the Peace River Formation are being exploited in the Southern Extension.

Jan 1, 1993

By R. R. Unterberger

This paper addresses the problem of seeing into rock. We will consider two methods, first to use radar, or electromagnetic wave pulses, to probe into rock ahead of mining and second to use sonar, or sound wave pulses, to probe into rock. Both are non destructive and capable of giving information on hazards ahead of mining. Such hazards might be a borehole full of water possibly leading to a high pressure aquifer somewhere above the mine level, changes in rock type, or the edge or top of a salt dome. Most of the work described in this paper deals with probing through rock salt which we have done successfully to over 2000 meters maximum range. We discuss first the radar probing and then the sonar probing. RADAR PROBING OF ROCK SALT Theory All electrodynamics are based on Maxwell&apos;s equations, which are in vector form [D = P (1) •B = 0 (2) aB V x E _ -(3) at aD •x H = J + - (4) at] where D and E are the electric displacement and electric field intensity vectors respectively, B is the magnetic induction or flux density

Jan 1, 1979

By R. Gilliam

The Jewett Mine is located in two East Central Texas Counties, Leon County and Freestone County. The area is primarily suited for agriculture with approximately 90% of its agricultural income coming from beef cattle and hogs. In addition to livestock both of these counties produce hay, oats for grazing, pecans and corn. There are 1,101 farms and/or ranches in Freestone County consisting of 381,248 acres. Less than 15% of this acreage is harvested croplands. Leon County has 1,227 farms and/or ranches for a total of 442,387 acres, of which less than 13% is harvested cropland. Total annual agricultural sales for Leon County are approximately $36 million and Freestone County has approximately $21 million. Ninety percent of the annual agricultural sales derive from livestock.

Jan 1, 1992

By A. K. Bakshi, K. J. Shoop, Komar S. Kawatra, T. C. Eisele

Slurry rheology can have significant impact on the performance of autogenous grinding circuits. A viscous slurry can act as a cushion and retard impact forces between the media and the ore, which reduces grinding efficiency. On the other hand, a dilute slurry will not be viscous enough to hold slurry in the impact zone of the media, which will lead to inefficient use of impact energy. An unfavorable rheology can also lead to overgrinding or centrifuging of the slurry inside the mill. Slurry rheology also affect classification, with higher viscosity increasing the cut size. In this article, the causes of the rheological effects on autogenous grinding and hydrocyclone classification have been discussed. Both plant and pilot scale data from autogenous grinding have been provided to show the effects of viscosity on specific energy con- sumption and other breakage characteristics of the ore. It is shown that: (1) high viscosity, produced by low temperature and high fines content, significantly increases the specific energy consumption and the production of critical size material in an autogenous mill; (2) In hydrocyclone operation, increasing the viscosity causes the d50(c) size to become coarser.

Jan 1, 1998

By Charles L. Kimbell

In 1989, worldwide total mineral industry activity registered advances from 1988. The advances may not have been as noteworthy as in 1988, but they can be regarded as a worthy theme for this article. The momentous political events throughout the centrally planned economy world had only a modest impact on actual 1989 industry performance. But these events have such potential for worldwide changes in economic activity in future years that they dwarf the actual happenings of 1989 in the minerals industry. Perhaps most significant factor here is the rapidity with which these changes have occurred. The end of World War II saw the almost immediate division of the world into major economic blocs. Since then, mineral industry activities and other industrial operations have been governed, to a considerable extent, by this partitioning. The developed market economy nations have operated as a group, the centrally planned economy states as another group. And these two groups essentially have vied for recognition in mineral industry operations in the developing economy states of Asia, Africa, and Latin America. The boundaries of these country blocs were fixed in the late 1940s and early 1950s. They were not markedly altered in the ensuing 40 years. We have seen the establishment of the Organization of Petroleum Exporting Countries, the continued Arab-Israeli confrontations in the Near East, the upheavals surrounding the rise of Moslem Fundamentalism in Iran, and the establishment of Soviet-oriented governments in Cuba and Nicaragua. These events have had notable effects on the world economy. But they have done little to change the pattern of market economy states functioning as a competitive bloc with the centrally-planned economy countries.

Jan 1, 1990

By Peter V. Avotins

During last year&apos;s AIME meeting in New Orleans, Deepak Malhotra and I were discussing some of the topics that would be presented in this Symposium. It seemed appropriate that along with papers on specific reagent and flocculant types, we should address research management aspects of new product development. This development is a long, arduous task that requires a significant technical and fiscal commitment by the chemical company and potential users. A flow chart depicting the research process is shown in Figure 1. The sequence of events are plotted on an undefined time line. Our experience has shown that it takes 3-5 years to complete a typical reagent development project. A new project starts with an idea of how to do something better. The ideas range from relatively simple product modifications to opportunities created by technological change. An example of this is the use of flocculants in tailings operations to close the water recycle loop. The change was brought about by the need to conserve water and comply with environmental statutes. The result was the development and wide-spread use of synthetic polymers to help in solid-liquid separation. More recently the ups and downs of oil prices have led to development of coal water slurries as an alternative to fuel oil. The slurries contain high levels of chemicals (up to 3%) to insure proper stability and burn characteristics. There are technical changes under way right now that may lead to ideas for other new products. One exciting source of new technology is the ability to manipulate genetic material of microbes to select for specific capabilities. This has evolved by leaps and bounds over the past 5 years. Biologically assisted leaching and removal of wastewater impurities are two possible end uses. I&apos;m sure that there are many others. The ideas can originate anywhere and are often half-baked at first, but to lead to new products they must be refined to provide project definition and eventually a research plan. A chemical ,development project cannot be started without approval to commit the company&apos;s resources. The internal selling job is often very difficult. The company must see clear financial benefits in order to launch efforts that may not pay off for many years. It is critical to project the total market, profitability, eventual market share, and timing of introduction of the new product. There is much uncertainty in this and the research manager is often skating on thin ice to retain his credibility. Once we obtain support from upper management, the research team is assembled to start the project. The teams generally consist of organic chemists, research metallurgists, and technicians. They have access to analytical scientists and technicians for surface and analytical chemistry. The projects are often augmented by help from university staff and consultants. This is particularly true where there is a need to develop fundamental understanding of the technology in addition to synthesis of chemicals. The project now proceeds along two lines. First, there is an emphasis on understanding the prior art. Extensive literature and patent searches are undertaken to provide research leads and to keep from "reinventing the wheel" and infringing on someone else&apos;s patent. The scientists and technologists are qualified to conduct computer-assisted library searches. This process usually uncovers 80-90% of the relevant information. The remainder is very much harder to get and requires the help of professional library search staff with scientific backgrounds. Along with literature searching, the team begins synthesis of new compounds. These are screened by use of techniques such as microflotation or filtration in a Buchner funnel. The scientists are looking for the direction of response as they modify structural features . Inevitably, a large number of candidates reach the next stage, a laboratory bench test. At this point it is possible to set up a research plan and use project management techniques to monitor progress. The bench tests are conducted in larger equipment, usually requiring 100-1000 grams of test substrate. Typical laboratory flotation tests are run in Denver or Wemco cells.

Jan 1, 1986

By S. Yap, F. J. Sotillo, L. P. Irwin, F. M. Utsey

Slimes, especially clays, are detrimental to several processes in the Mining Industry. The efficiency of classification, clarification, gravity separation, and flotation decreases significantly in the presence of slimes and clays. This problem is particularly critical in the Phosphate and Sulfide Industries. To reduce the effect of slimes in mineral processing, several desliming techniques and chemical additives are used, such as sodium silicate, sodium carbonate, sulfuric acid, tripolyphosphate, hexameta phosphate, etc. Lately, the Mining Chemical industry has shift to more “Specifically Developed” reagents that offer the most efficient and cost effective performance, mainly using organic polymers. For this purpose, the Mining Chemical Industry needs to understand the crystal chemistry of minerals, the chemistry of the aqueous media, the interactions in solids-aqueous-gas interfaces, the rheology of the system, and the plant operation conditions and parameters. This paper describes the use of surface chemistry fundamentals on the design of an organic polymer capable of modifying the rheology of clayish slurries of a phosphate ore. The change in the rheological characteristics of the clayish phosphate slurries allow fine ore particles to settle faster by reducing the slurry viscosity. Thus, abetter separation of the ore from the slimes is possible using gravitational or centrifugal forces. As examples of the application of this reagent, industrial and pilot plant tests on desliming using tanks and hydrocyclones are presented. These tests showed the reduction of 32%-36% in ore losses for different phosphate ores during desliming operations, and the increase of cyclones desliming efficiency to 80%. Tests were also carried out to improve the rejection of unwanted iron bearing slimes in phosphate feed. These tests demonstrated that it is possible to reduce by 0.25%-1.23% Fe2O3content in the flotation feed product. As a result, significant economical benefits are observed with the use of this new technology without any adverse effect on down stream operations, such as clay settling or phosphate flotation.

Jan 1, 2003

By J. Litsenberger, T. E. Marshall, P. R. Coyle, L. J. Prosser, A. T. Iannacchione

For the first time in an underground stone mine, the relationship between roof movement and microseismic emissions was examined in conjunction with two distinct roof fall areas. As roof monitoring increases in acceptance and monitoring technology advances, the goal of providing reliable roof fall detection systems to enhance the safety of underground mine workers moves closer to reality. Instrumental to reaching that goal is the ability to interpret accurately and completely roof movement and microseismic emissions, which can serve as precursors to roof falls. This paper examines the capabilities of convergence and microseismic monitoring systems to better understand roof rock failure mechanics and to anticipate roof falls. An understanding of how these techniques are used and how they interact with each other is critical in developing the most effective ground control strategy for our nation’s mines.

Jan 1, 2004

By G. Balletto

Increasing environmental awareness leads to a reflection on the consequences of a non-appropriate use of mining resources. In this sense the determination of the mining requirements for the building industry is the necessary prerequisite to activate planning in mining according to the principles of environmental sustainability. Experience shows that there is a relationship between the production of buildings in relation to the shape of the city and the resulting demand for minerals. The increasingly urgent demand for maintenance and restructuring by existing buildings will stretch further the demand for minerals with an excessive, no longer sustainable withdrawal, which will lead to focussing greater attention on environmental policies oriented to the use of alternative materials including materials from recycling. It is pointed out moreover that the joint action of land use planning and mining planning leads to interesting applications that have significant repercussions on the environment.

Jan 1, 2005

By T. E. Wilson

The length of Alaska’s coastline, combined with the presence of a significant number of fjords, encourages consideration of marine disposal of mine tailings. However, since various factors govern the viability of the submarine tailings disposal (STD) option, the decision making process is complex. An expert system, called Submarine Tailings Disposal Expert System (STADES) that will help mining project planners explore the feasibility of STD, was developed. Existing literature, supplemented by engineering recommendations, on the various aspects of marine disposal of tailings was reviewed and formed the knowledge base for the expert system. The shell used to develop the expert system was LEVEL5®.

Jan 1, 2001

By J. J. Zimmerman

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industries. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. Mine Safety and Health Administration (MSHA) coal noise data from 2000-2004 show that the continuous mining machine is first among all equipment with 35% of the noise overexposures. Joy Mining Machinery, in collaboration with the National Institute for Occupational Safety and Health (NIOSH), is conducting research to reduce noise generated by continuous mining machines. This paper describes a ?JOY Designed for Noise Reduction? (JOY-DNR; Patent Pending) tail section as a noise control for reducing the noise overexposures of continuous mining machine operators. Underground results show a 45% and 65% noise exposure reduction for the operator when compared to a standard machine. Utilizing this newly developed noise control, along with previously proven controls, will provide continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2010