Search Documents

By W. P. Blacutt

A financial-economic model incorporating physical, market and policy variables has been developed for mining investment in Bolivia. Additional risk criteria emanating from political instability, new mining legislation, recent environmental regulations and a new minerals taxation system are accounted for and are integrated into the investment decision model. Results of the model indicate that geologic and market variables have the dominant effect on the investment-worth function. Among policy variables, exchange rate and taxation policies have the most significant influence. Depreciation allowance for infrastructure development has negligible weight in the investment-worth function. The business structure of the firm considering investing in the Bolivian Polymetallic Project, is found to be an instrumental factor in the investment-worth outcome.

Jan 1, 1995

By Frank J. Hirner

Economic open-pit and surface mining often call for ever increasing volumes of lower grade materials. So it is important, often critical, to develop precise expense and production estimates for the large electric mining shovels now in use. An electric shovel's basic application is to "shovel up" material, starting at ground level with the dipper moving up into a working face or bank. It's impractical to dig below ground level with a shovel, except briefly or in unusual circumstances. The shovel working face is "the bank," whether the material is dug from natural bed or blasted. The shovel's digging attachment, the boom and dipper handle, is built in standard and long range configurations. A standard digging attachment is normally used for loading into haulage equipment. The long range attachment is normally used for side or hack casting to a spoil pile. It is also used fir loading into haulage equipment placed above shovel ground level, as in some coal loading applications. Shovel clipper size and hauler capacity should he matched so that a hauler can he loaded in three to four shovel work cycles. Five cycles is usually the limit of good practice. If fewer than three cycles are required, the hauler is too small. More than five cycles indicates possible excess harder waiting time for loading, or shovel waiting time for too few haulers. Full dipper loads, including the last dipper or ''pass, " are essential for economical shovel and hauler match. Consistent need for a final partly full dipper to fill the hauler shows an improper match between the two.

Feb 1, 1981

By Ehsan Alavi Gharahbagh

Tool and cutterhead wear is a crucial issue in soft ground tunneling, especially because tool inspection, maintenance, and replacement are done under difficult conditions, and often under pressurized faces or under ?hyperbaric interventions?. Overall, tool inspection and changing is a time consuming and costly step, which needs to be quantified and the related costs accounted for in any construction contract for scheduling and costing of the tunnels at design stage or bid preparation. However, lack of a universally accepted index or measure for soil abrasivity in the geotechnical reports has made it difficult, if not impossible, to define cutter wear for this purpose. Soil abrasion and its impact on cutting tools for tunneling machines under dry or wet conditions have recently been under spot light due to construction claims in several of the recent tunneling projects. The objective of this paper is to examine soil?s physical, mechanical and tribological properties related to the interface of the soil and excavation tools and discuss ways to measure soil abrasivity in a quantitative and repeatable manner. The paper will discuss the efforts that are underway to develop a new soil abrasivity index and the fabrication of a new testing device for this purpose.

Jan 1, 2010

By Raj K. Rajamani, Ilesh M. Shah

Maintaining pH, a routine requirement in many industrial processes, is by no means trivial. The control is troublesome because of the inherent nonlinearity and frequently changing process dynamics. Many researchers in the past have investigated advanced on-line estimation and/or adaptive control techniques to overcome these difficulties. Most methods require the development of a complex mathematical model. The present work deals with the use of a simple and elegant method for pH control, based on the use of fuzzy logic. First, a standard fuzzy-logic controller is discussed, followed by a self-organizing controller. The latter algorithm generates a set of rules based on observation of the process. Thus it is a learning algorithm. The development and application of the algorithms to a laboratory acid-base neutralization experiment are presented. This elegant technique is powerful and deserves attention in mineral pro- cessing.

Jan 1, 1990

By Ron VanRiper, Ben W. Burdett, Randy A. Ynchausti, Jeff D. McKay, Dan Lampshire, Thomas W. Toronto

An adaptive process control system was installed in Cortez Gold Mines Mill #2 Grinding Plant in Nevada. The installation, commissioning, and testing of the system took approximately 80 manweeks, but final test results show that the system paid for itself through increased throughput within two weeks of commissioning. Both crisp and fuzzy rules are used in the expert rule base which is also integrated with continually adapting neural network models. The expert rules and models are used by predictors, and optimizers to allow the control system to provide optimum process performance under continually varying feed conditions. The selection, installation, rule and predictor configuration, and statistically verifiable testing of the control system in the Cortez Gold Mines Mill #2 Grinding Plant is described in the paper.

Jan 1, 1999

By N. P. Reddy, Y. J. Wang

This paper describes an experimental setup for multiple fan ventilation systems at the ventilation laboratory of the West Virginia University Department of Mining Engineering. Housed in a 30-ft x 70 -ft room, the experimental setup consists of three 18-in., variable-speed, axial flow fans; an 18-in. -diam, fiberglass tubing; associated fittings for arranging networks; and a picot-tube measuring and data-acquisition system. The fiberglass tubing and fans can be organized into non-planar networks of two or three fans. The setup is mainly designed for studying the characteristic curves, operating points and fan stall for multiple fan ventilation systems.

Jan 1, 1993

By Randal J. Barnes

In, any open pit mine the ability to make accurate production estimations for the shovel-truck system is an important asset. This is true in an operating mine wishing to estimate production under a set of system modifications (i.e. more trucks, fewer loaders, change in roads, etc.), as well as in the pre- mining planning stages of a property. Many different methods have been proposed for solving this problem; some of the methods rely heavily on "rules of thumb" while others are highly mathematical and require access to a high speed digital computer. Analysis of shovel-truck systems with the use of simulation models is a widely accepted technique within the industry. Through the use of such models it is possible to account for much of the inherent variability of the system and thus produce meaningful results. However, simulation studies are expensive. Formulation and setup of the actual simulation model requires a significant commitment of time and energy. In addition, the cost of the necessary computer runs is often of considerable magnitude.

Jan 1, 1979

By W. J. Pennstrom, J. R. Arnold

This paper focuses on solution-balance management around heap-leach operations. Experience has shown that increased leach recoveries can be achieved by utilizing various leach-solution recirculation techniques. The most prominent solution-recirculation technique is intermediate leaching. The net effect of intermediate leaching is to increase recovery plant performance by increasing solution concentration tenors, to increase metal recovery by increasing the total leach time and to decrease the overall capital expenditures required for metal-recovery facilities. The adverse effect on the flow of cash from increased metal inventories in the recirculating solutions is offset by increased metal recovery and lower operating costs per unit produced.

Jan 1, 2000

By M. L. Nave, R. E. Melley

DC motor drives are available technology for belt conveyors. The success of the application in mining depends on adequate and timely consideration of DC drive features. The purpose of this paper is to familiarize and inform possible mining users of DC drive attributes.

Jan 1, 1996

By Kevin L. Purdy

Chemical dewatering aids for mineral slurries generally fall into two classes: surfactants and flocculants, which can be used separately or together. Current industrial use of both types of reagents is summarized for sulfide and non-metallic minerals, as well as uranium and gold leach residues and coal refuse. Laboratory testing for reagent selection is briefly discussed along with reagent preparation. Chemical properties of the reagents which affect the suitability for particular applications are analyzed. [BLANK PAGES - Are in the original]

Jan 1, 1986

By William Mayrsohn

IMTRODUCTION The marketing aspects of a new precious metals property is often not considered until the mine actually begins production. At this point in time it is often too late or too expensive to change the mine's final product and not enough time to do an effective marketing program. MINE PRODUCT The rule for determining the mine's final product: The higher the gold and silver content, the greater return of metal at the lowest post-mining cost. . Dore Bullion: Most advantageous Advantages: - Highest return of metal. - Lowest refining cost per ounce of gold and silver. - Very compact and easy to ship in small quantities. - Easy to assay. - Assays between mine and refiner are comparable. - Melt losses are very small at the refiner. - Outturn of gold and silver 20-30 days for quick cash flow. - Gold/silver refiners can return or purchase metal soon after arrival at a nominal financing cost.

Jan 1, 1987

By N. D. Cristescu

An analysis of the interaction between a creeping rock and a yieldable lining is presented. The following cases are considered: an elastic lining, a lining made of circular shaft rings that may slide at their joints, a lining made of circular reinforced concrete panels with wooden compressible strips inserted between the longitudinal joints and a yieldable support that has a compressible broken-rock stratum between the support and plane rock. By formulating a mathematical model for the rock-lining interaction, one can optimize the sequence of excavation-lining application. To keep costs to a minimum, one can also choose the most appropriate lining for the corresponding rheological properties of the rock.

Jan 1, 1997

By J. C. Stankus, S. S. Peng

Many coal seams are associated with soft floor strata. During mine development, if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One method for controlling floor heave is floor bolting. This paper describes the demonstration of flour bolting methods in a West Virginia, info coal mine. Three methods were used: vertical full resin bolting, floor truss bolting and floor truss bolting pins a floor slot at the center of the entry. The design of each method and the experimental results are discussed.

Jan 1, 1995

By A. I. A. Salama

A computationally efficient technique for generating a balanced set of density or size separation data is developed. The technique proposed utilized minimization of a modified form of error squares to generate the optimum estimates of outputs mass yields (splits) and balanced direct mass distributions of feed and outputs. The estimated separation data set satisfies mass balance conditions of the streams mass distributions around the separator. The technique proposed avoids the generation of small negative values for the estimated feed and outputs direct mass distributions. Actual data are used to demonstrate the technique proposed.

Jan 1, 1996

By Kousik Sinha

The advantage of using a clean coal as a feedstock in a direct liquefaction plant is improved performance of the plant by several factors e.g., increased throughput of coal; reduced wear and tear of valves, pipes, and pumps; increased liquid yields, etc. This paper examines the technical feasibility for cleaning Illinois #6 coal as a feedstock to a direct coal liquefaction plant via selective agglomeration using a coal-derived heavy distillate, Wilsonville V-1074 as agglomerant. Effects of addition of Kerosene or coal-derived Naphtha as conditioner, coal particle size, slurry pH, oil to coal ratio, and operating temperature on ash reduction and clean coal weight recovery have been studied. Results show that about 70% of the ash can be removed from this coal and the clean coal weight recovery over 85% can be achieved by using this technique with suitable selection of coal particle size, slurry pH, mixing intensity and oil to coal ratio.

Jan 1, 1991

By J. Cheung, H. Rabia

The traditional methods for predicting mine air temperatures are based on steady state heat transfer models as developed by Voss (1969) and Starfield (1983). These models are useful in providing approximate predictions of air temperatures in trunk and gate roadways. More complex models are required to provide predictions along faces. In practice, the heat flow in underground mines is of transient nature and recent observations in some British Coal mines show temperature variations of up to 5°C during a working week at any one point. In addition, the recent introduction of district recirculation of mine air in British mines requires a more precise prediction of air temperatures during start up of the system or during breakdown. A transient heat transfer theory based on the work of Jordon is presented. The method lends itself easily to computers due to the large number of calculations involved. The proposed transient model is validated using actual temperature data collected in roadways in Wearmouth Colliery in the North East of England. The transient results are compared with the steady state predictions of Voss (1969). Finally, predictions of air temperature in roadways for a recirculation system will be made using both the transient and steady state models. Temperature predictions along faces will be made using a separate model.

Jan 1, 1989

By L. Stas

The authors have been interested in stress measurements in the rock mass for a long time. This paper describes the development of new apparatus for stress measurements in a rock mass. The principle of stress measurement by this device is based on the relief method as applied on the conical shaped surface of the bottom of a borehole. The design started based on the experience of K. Sugawara and Y. Obara who have been using the compact conical borehole over-coring system (CCBO). The conical shape of the strain gauge probe CCBO makes the fixation of the probe in borehole easy and, also, makes the measurement of stress in independent directions possible. The principle of the measuring method, the preparation of the borehole, the design of the probe for continuous measurement of stress during the course of overcoring are described. Also, a simplified version of the probe for long term monitoring of stress variations in the rock mass by means of the inserted body method and the initial laboratory results and in-situ testing of the development sample are described. Additionally, testing was done regarding the possible glues in relationship to the creep effect for this case.

Jan 1, 2006

By O. Akinkugbe

The safe, productive exploitation of coal in multiple-seam situations requires specific design technology. At present, there are two general design approaches that the mining engineer can use to analyze the multiple-seam problem in question, either simple empirical relationships or complex numerical models. Often, the empirical approaches are too general for the specific problem and the numerical models require too much time and expertise for the practicing engineer. In this paper, a new program designed for quickly and easily calculating the stresses, strains, and safety factors associated with basic multiple-seam mining situations is presented. The program implements a simplified, two-dimensional boundary-element method in order to model the complex multiple-seam stress and displacement interactions. The program incorporates automatic coal and gob property generation to simplify the input, and inherently calculates pillar safety factors to enhance the output.

Jan 1, 2004

By M. Takayasu, J. Y. Hwang, F. J. Friedlaender, G. Kullerud

Al unite has been used as raw material for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores are quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 µm. Adequate separation techniques for such ultrafine particles have not been developed. A new method for the beneficiation of al unite ore is proposed in this study. This method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g., an al unite concentrate of 90% grade with 80% recovery, has been obtained from Utah ore. Techniques for selective co-flocculation of magnetite and quartz, separation of the carried quartz, and recovery of magnetite after separation are discussed.

Jan 1, 1987

By Jon “Ike” Isaacson, Frank Perrone, Eric Prantil

"Tunneling through an urban environment carries many inherent risks to the immediate local infrastructure and subsequently to the project stakeholders. On the CQ031 Contract of the East Side Access Project in Queens, New York, twin 22.5’ diameter Herrenknecht Slurry TBMs were mined within close proximity to many infrastructure assets, with cover of less than half a shield diameter at times. Multiple public bridges and critical railroad infrastructure including catenary poles and signal towers supporting the busiest rail interlocking in the United States required underpinning systems. The support program for these structures was refined over the course of the four tunnel drives. It is the intent of this paper to show how the interaction between the temporary structures, instrumentation monitoring plan, and risk assessment program melded to provide a system which the owner, contractor, and designer relied on as a tool to ensure the project success without impacting the public surroundings. PROJECT BACKGROUND The East Side Access (ESA) megaproject located in New York City, N.Y is a multi billion dollar program for the Metropolitan Transit Authority Capital Construction (MTACC) with the main goal of bringing the Long Island Railroad (LIRR) commuter rail to Grand Central Station located in the heart of Midtown Manhattan. When completed, the project will significantly reduce congestion both into and out of Penn Station, the current terminus of the LIRR. In order to accomplish this, multiple contracts of varying scope are required to operate simultaneously in both Queens, N.Y and Manhattan. In 2009, the CQ031 Queens Bored Tunnels Contract was awarded to the joint venture of Granite Construction Northeast, Traylor Bros. Inc., and Frontier Kemper (G.T.F). The main scope of this contract was to excavate four segmentally lined soft ground tunnels underneath the Sunnyside Rail Yard in Queens, New York. Additional scope of work included the construction of a tunnel approach structure, electrical substation, and multipurpose ventilation and egress facility."

Jan 1, 2016