Search Documents

By Meng Li, Hao Nie, Weitian Ding, Mamdouh Omran, Ying Li, Yao Ge, Yaowei Yu, Abourehab Hammam, Lei Zan

This study examines the isothermal and non-isothermal reduction behaviors of iron ore compacts in a pure hydrogen atmosphere and compares the results obtained during the reduction process by CO. The different phases accompanying the reduction reactions were identified using X-ray diffraction (XRD) and its morphology was microscopically examined. In isothermal experiments, temperature plays a significant role in the reduction process. At any given temperature, the reduction rate during the initial stages is higher than that during the final stages. The reduction rate in H2 atmosphere was faster than in CO gas. The comparison of activation energy values suggested that reduction with H2 is more efficient thanwith CO. At the same temperature, the time required to achieve a certain degree of reduction was lower when using H2 gas than CO atmosphere. In non-isothermal tests, the heating rate has a significant effect on the reduction rate and reduction extent. At the same heating rate, the degree of reduction was higher in H2 atmosphere than in CO gas. Based on experimental data, the parameters of reaction kinetics were deduced by application of model-free and model-fitting methods. The reduction in H2 atmosphere was controlled by nucleation model (Avrami-Erofeev model), while the CO reduction reaction was controlled by gas diffusion.

Sep 29, 2020

By A. B. Cecala

Over the past decade, a substantial effort has been made to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment to reduce respirable dust exposures to the equipment operators. As part of this effort, the National Institute for Occupational Safety and Health, (NIOSH) completed a comprehensive laboratory study which determined the significant factors for cab filtration and pressurization systems. From this information, a major underground mining equipment manufacturer designed a filtration and pressurization system which was incorporated into the enclosed cabs of its equipment. A long-term evaluation was performed on the effectiveness of this filtration and pressurization system to improve the air quality in the enclosed cabs of two different pieces of equipment, being a face drill and a roof-bolter machine, at an underground limestone mine. This long-term evaluation demonstrated a significant reduction in dust levels comparing outside to inside cab respirable dust concentrations. During this evaluation, a modification to remove one of the filters on the roof-bolter machine simplified the design without sacrificing the system?s efficiency. Testing using particle count instruments performed during non-production time periods on both pieces of equipment indicated Protection Factors greater than 100 when comparing respirable-sized dust particles inside the enclosed cab relative to outside.

Jan 1, 2012

By R Kerrich

Early-Archaean (3.26 Ga) volcanogenic massive sulphide (VMS) deposits located within the low strain and sub-prehnite-pumpellyite metamorphic-grade Strelley greenstone belt, East Pilbara, Western Australia, contain exceptionally well preserved sulphide textures which are directly analogous to those of sulphide chimneys formed by black smokers at present day submarine hydrothermal vents. The VMS deposits are associated with seafloor alteration zones in and below silica-carbonate laminites, at the top of tholeiitic to calc-alkaline intermediate and felsic rocks. VMS mineralisation comprises stratabound Zn-rich sulphide lenses with significant Cu and barite, and variable Pb and Ag, above Cu-rich stringer zones, all of which are similar to Phanerozoic polymetallic or Kuroko VMS deposits. Sulphide-sulphate mineralisation implicates hydrothermal discharge into sulphate-bearing ocean waters, ruling out a globally anoxic Archaean hydrosphere. The volcanic rocks and co-magmatic sub-volcanic intrusion hosting the VMS deposits are characterised by the conjunction of LILE>LREE>HREE, and Phanerozoic La/Yb with negative normalised anomalies of Nb, P and Ti, consistent with derivation via subduction zone hydrous metasomatism fusing the mantle lithosphere.

Jan 1, 1995

By John G. Kelly

"In 1982 an extensive study was carried out to determine the best means of size reduction for the ore to be hoisted through the borehole hoisting system at Sherritt Gordon's Fox Mine.The study examined three alternatives:1. a jaw crusher,2. pneumatic rockbreaker(s) at a grizzly, and3. hydraulic rockbreaker(s) at a grizzly.The final decision was a compromise between alternatives 2 and 3. Two rockbreakers, one pneumatic and one hydraulic, were installed over a single grizzly. Some modifications have been made to the system, but over-all it has operated at acceptable levels since its installation in July 1983.As all the ore passes through a jaw crusher before being hoisted to surface, an evaluation of the relative performance and cost-effectiveness of the jaw crusher and the two types of rockbreakers is possible. This paper outlines the initial study, and compares the three breaking systems in operation at Fox Mine.IntroductionThe Fox Mine of Sherritt Gordon Mines Ltd. is located 800 kilometres north of Winnipeg near Lynn Lake in Northern Manitoba. Production at the copper-zinc orebody began in 1970 at a rate of 3,000 tons per day. Over 12.5 million tons will have been hoisted from the underground mine when the ore reserves are depleted in October 1985.The mining method at Fox Mine is sub-level open stoping with delayed backfilling are from the upper level stopes, above the 2000 level, is mucked on the main levels established at 400-ft elevation intervals, and is fed through a central orepass to the crusher located on 2100 level. Production in the lower levels commenced in 1975, and ore from the 2200 and 2400 level stopes was hauled up a 15010 ramp by 26-ton trucks to the 2000 level orepass dump. Projected production rates from the 2600 and 2800 levels using the trucking system were too low, and therefore, in 1983 a borehole hoisting system was commissioned to hoist that ore'!'. One thousand tons per day of ore are skipped through an 8-ft diameter borehole from the 2650 level loading pocket and dumped on the 2000 level. The ore is transferred by LHD to the main orepass for crushing before being conveyed to the main shaft for hoisting to surface (Fig. 1)."

Jan 1, 1986

By A. M. Gaudin

THE purpose of ore dressing is to separate the rough ore into one or several valuable concentrates and a discarded tailing. The first step is to crush the ore so that the resulting particles may be individually valuable or worthless. The next step generally has to be a sizing operation, because the property by which concentration is effected depends on the size of the in-dividual mineral particles as well as on their physical properties. These two effects may cancel each other if a preliminary sizing is not resorted to. Sizing is accomplished by screening or classifying. Screening depends almost solely on the dimensions of the particles; classifying depends also on the specific gravity of the particles and the viscosity of the settling medium in which the classifying operation is conducted. Classification, therefore, is to a certain extent a con-centrating operation as well as a sizing operation. Before the days of concentration by flotation, the available screens were mechanically poor. As a result classification was employed for sizing in the range. of comparatively coarse sands (table feeds). In recent years, the advent of stage-grinding to flotation size has brought about the development of good screens, which are more economical than classifiers down to about 20, -mesh. With decreasing size at which separation is to be made, screens become increasingly uneconomical, while classifiers become increasingly economical. The line of demarcation between the respective fields of screening .and classification is, therefore, fairly sharp. With the development of processes of concentrating finely comminuted ore, the need for classifiers or other sizing devices operating so as to make efficiently a split at a very fine size has become increasingly apparent. Such classifiers might be termed de-slimers, from the fact that they separate a material having a slimy ap-pearance from one having the characteristics of a sand. Sizing-tests are carried on by means of testing sieves, the finest of which have apertures of about 1/500 of an inch. The 200-mesh sieve, which has an average open-ing of 0.0029 linear inches is generally considered the limit of practical test-sizing. As a result, little is known of minus 200-mesh material and the advantages of classifying concentrator feeds within the minus 200-mesh range has been overlooked. An extension of the -present sieve scale beyond the 200-mesh screen is given in Table 1.

Jan 2, 1927

By H. Sevim, M. K. Mohanty, Y. P. Chugh

The economics of “Conventional” and “Advanced Fine Coal Cleaning” (AFCC) circuits for refuse pond reclamation as well as active mine/preparation plant applications have been evaluated. The benefits of innovative tailings management schemes on the profitability of mining enterprises have also been evaluated as a part of this study. Analyses have been conducted for scenarios involving generation of two different product qualities of 5.81%, a quality that was obtained during AFCC circuit operation at SIU, and a more typical 8% product ash. The inability of the conventional circuits to achieve profitability while producing the lower ash content product is revealed from this approach. The spiral-only circuit is unable to produce a 5.81% ash product. A different version of the same circuit involving spirals and column flotation produced the desired product quality but could not maintain profitability. The AFCC circuits on the other hand, achieve net present values greater than $6 million, with return on investment in excess of 50%, in the water-only as well as dense medium mode, with and without tailings management. Addition of tailings management system to any of the circuits is found to enhance the project economics. The comparison of water-only and dense-medium applications of the AFCC circuits indicate a better suitability of the dense-medium circuit for producing premium quality products. Application of AFCC circuits in active mines offer better economics compared to applications in refuse pond recovery operations. The superior project economics are a result of reduced overhead cost and use of existing material handling facilities. Sensitivity analysis reveals the significance of capacity utilization on project economics.

Jan 1, 2002

By Timothy C. Siegel

A piled raft refers to a shallow foundation that is structurally connected to the piles, while composite ground refers to a soil-pile matrix where the piles are not structurally connected. The design objectives for both a piled raft and composite ground are (excluding special considerations such as expansive soil): (1) to provide a sufficient ultimate resistance and (2) to distribute the load into the soil-pile matrix so that the settlement experienced by the shallow foundation is within tolerable limits. A simplified model is proposed for a shallow foundation on composite ground where the foundation settlement is estimated as the sum of the downward movement of the piles plus the downward movement of the shallow foundation relative to the pile head. The proposed simplified model is applied using conventional geotechnical analyses for two hypothetical examples of shallow foundations undergoing compression settlement.

Jan 1, 2011

By William E. Ford, Edward Salisbury Dana

Secondary Twinning. - When there is reason to believe that the twinning has been produced subsequently to the original formation of the crystal, or crystalline mass, as, for example, by pressure, it is said to be secondary. Thus the calcite grains of a crystalline limestone often show such secondary twinning lamella?. The same are occasionally observed (Ilc, 001) in pyroxene crystals. Further, the polysynthetic twinning of the triclinic feldspars is often secondary in origin. This subject is further discussed on a later page, where it is also explained that in certain cases twinning may be produced artificially in a crystal individual - e.g., in calcite (see Art. 282).

Jan 1, 1922

By John Vynne

Too often, a mine’s operations, including drilling, blasting, loading, hauling, crushing, processing, etc., are considered independent steps, rather then a continuous process. In fact, these are interdependent operations with each step in the process having an impact on subsequent operations. If the effectiveness of the drilling and blasting operations can be improved, they will impact the entire mining process. Some of the resulting improvements include: level benches on grade; fragmentation and diggability with the result being reduced loading times; haul cycles improvements; and the crushing and milling operations will be more efficient and less energy consumed. Thunderbird refers to this as “Drill to Mill” information cycle or process. This paper focuses on two of the technological enhancements Thunderbird has added to its drill monitors that allow the mines to impact the “Drill to Mill” concept. These enhancements are: incorporating global positioning satellites into drill monitors; and radio off-loading of data.

Jan 1, 2001

The results of precious metal exploration carried out by Amoco Minerals New Zealand Limited over EL 33-137 in the Longwood Range, Southland, are described. Widespread gold and platinum in alluvial deposits on the perimeter of the range and anomalous gold in stream sediments on its southern and south western flanks indicates that the precious metals were probably derived from erosion of the mafic rocks of the Longwood Complex.

Jan 1, 1983

Platinum-group minerals (PGM) are recorded from a number of localities along theWaiau River, western Southland, and the south coast of the South Island, New Zealand. At each locality, small amounts of PGMs were recovered as by-products of historical gold mining operations. During the period 1890-1950 an estimated 1000-2000 oz. of æplatinumÆ were recovered from the region, the only area within New Zealand where PGM have been commercially exploited. The PGM suite of southern New Zealand consists of Pt-Fe alloys, IPGE (iridium subgroup, platinum-group elements) alloys, sperrylite (PtAs2), cooperite (PtS) and braggite ((Pt,Pd)S). The composition of Pt-Fe alloy exhibits considerable variation and two compositional populations are recognised. Some Pt-Fe alloy grains are chemically zoned. Iridium is the most abundant IPGE alloy phase and often contains considerable Pt, in contrast to osmium and ruthenium alloys. Cooperite and braggite grains are characterised by extremely low concentrations of Ni.   Exsolution of osmium and iridium from Pt-Fe alloy and Pt-Fe alloy from iridium is observed Several PGM host mineral inclusions which vary from single to poly-phase, display rounded to equant outlines and range in diameter from greater than 100 ¦m to less than 5 ¦m. Olivine and Ni-sulphide inclusions are only present within IPGE alloys. Pt-Fe alloy, cooperite, braggite and sperrylite host Cu-Fe sulphides, a wide variety of PGM, clinopyroxene, amphibole, magnetite and plagioclase within inclusions. Sperrylite also hosts Pd bismuthiotellurides, gold and several potassium-rich silicate phases. Similarities in inclusion phases and mineral chemistry from several localities suggest that the PGM are derived from a single (as yet unidentified), probably calc-alkaline magmatic source. This source is situated somewhere along the margins of the western Southland sedimentary basin where PGM liberated by erosion are transported down the Waiau River and dispersed eastwards along the coast by strong longshore currents.

Jan 1, 1995

By Danny A. Riley, James R. Sanger, Hani S. Matloub, Lin-Ling Zhang, Ji-Geng Yan

This experimental study was done to determine pathological feature of vibration injury to the peripheral nerves in the hind limbs of rats exposed to 7 days of vibration. Materials and Methods Animals: Twenty four male Sprague-Dawley rats weighing 350-400 grams were randomly divided into two groups: sham control group and vibrated group. To document vibration-induced changes in the experimental model, the sciatic nerve was used because it contains both motor and sensory fibers and is relatively superficial in the posterior thigh. Customized Vibrating Platform: The hind limbs of the rats in the vibrated group were exposed to vibration in a custom-built vibrating apparatus consisting of two platforms: a smaller vibrating platform on which the hind limbs of the rat are secured, and a larger platform on which the remainder of the body rests. The vibration parameters (frequency 43.5 Hz, amplitude 1.5mm, acceleration 4.75G, velocity 6cm/sec., and displacement of 3.0mm) of this model were measured. Methods: Rats were anesthetized with 35mg/kg of intraperitoneal Nembutal (phenobarbital) and their hind limbs fixed to the vibrating platform by Velcro loops. Both hind limbs rest on the vibrating platform while the remainder of the body rests on the larger platform. The rats were vibrated 4 hours a day, for 7 days, with close monitoring of the vibration parameters. The 4-hour duration of hazardous vibration was based on recommendations from the British Standards Institution. The sciatic nerve of rats not exposed to vibration, but similarly anesthetized and secured to the vibrating platform, acted as controls. At the end of seven days of exposure to vibration, nerves from both the vibrated rats and the control rats were harvested after perfusion of the lower half of the body using glutaraldehyde as described below. Neural Fixation: The aorta was cannulated, and the inferior vena cava was nicked and the animal was initially perfused with 0.9% buffered sodium chloride. This was followed by perfusion of a filtered mixture of 3% glutaraldehyde and 3% paraformaldehyde fixation solution, The tissue was subjected to post fixation by routine. The neural tissue was then submitted for light and electron microscopy. Results While light microscopy showed minimal histological differences between vibrated (n=12) and control nerves (n=12), the changes revealed by electron microscopy were dramatic. These included thickening of the epineurium, as well as thickening of the myelin sheath as compared with normal nerve. Also, the axon plasma was detached from the myelin sheaths, and many vacuoles were seen between the myelin laminae(Fig.1); These changes were found in all vibrated animals, and in the whole segment of each vibrated nerve. Myelin balls, consisting of

Jan 6, 2006

By M. H. Farjadi, J. Azari

Cost analysis of chrome ore reduction is one of the important issues facing ferrochrome producers in today?s competitive environment. Much of this depends on quality and various ratios in the actual ore. The latter can have a direct bearing on electricity consumption and optimum efficiency of the furnaces. While the industry has been successful in reducing costs by designing larger and more efficient furnaces, the role of the optimum blend of ore has perhaps been given less emphasis. This paper will discuss the general specification and metallurgical characteristics of various chrome ores for producing high carbon ferrochromium on industrial scale. By analysing the results obtained from smelting, including chromium recovery and energy consumption, the determining parameters in total cost of ferrochromium i.e. chrome ore; reductant and energy consumption can be optimized. Our study is based on actual experiences obtained from Faryab Ferroalloy Plant over a period of approximately three years.

Jan 1, 2004

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

By F. W. Tregarthen

"This paper gives a brief description of the methods used to form and implement the present planned maintenance program. The system is designed to assist plant personnel in their task of controlling a large work-force and maintaining the many and varied types of equipment used in a mining and concentrator operation. The types of reports and methods used in scheduling and work-loading are described. General built-in flexibility is derived from computer assistance to the Central Planning Group."

Jan 1, 1971

By Kai Nielsen

The paper presents the results of several industrial and laboratory blasting, crushing and grinding tests and experiments investigating how blasting can influence the subsequent crushing and grinding operations. The paper also describes how these results can be used in order to optimize the entire comminution process from solid ore to a semifinished or marketable product. Two cases are presented, one looking at the processing of fine grained taconite ore, and the other discussing the processing of raw milling product for cement burning.

Jan 1, 1998

By Fang Wu

The paper designs an extraction flow for the total recovery of nickel and cobalt and removing magnesium simultaneously from the cadthodic materials of the spent hydrogen-nickel and cadmium-nickel batteries. The separation of Co, Ni and Mg though P507 extraction .The extraction equilibrium pH is 4.5~5.0, ßNi/Co is 140~180, and ß Ni/Mg is 20~25; nickel and magnesium are scrubbed in two steps, in which the equilibrium pH of nickel and magnesium scrubbing is controlled at 5.0±0.1 and 4.4±0.1 respectively. The stepwise scrubbing technique is adopted to remove 94.5% of magnesium and to recover 99.45% of nickel and 95.35% of cobalt. During the integrated extraction and precipitation process the total recovery fraction of nickel and cobalt are 99.99% and 99.95%, and the recovery fraction of magnesium is 94.02%.The recovered NiSO4 and CoSO4 solution are enriched and crystallized.

Jan 1, 2009

Bubble Load Measurements in Flotation - A Critical Review of Current Practice

Sep 13, 2010

By R. N. Murarka

"Hydrocyclone modelling and selection procedure is illustrated. Computerized procedure for hydrocyclone cut size determination for grinding and non-grinding applications is described.A standard procedure for evaluating operating hydrocyclones is described in detail. Many case studies are illustrated comparing actual plant performance with the computer simulation output in terms of overflow product size distributions.INTRODUCTION Cyclones are widely used for applications such as: close circuit grinding, backfill, tailings and dewatering. Normally, cyclones are used for very fine separations where screens are not suitable or too expensive. Figure 1 shows the separation size range of various classifying devices. Cyclones are popular because of their low capital and operating cost. Cyclone selection procedure for different applications depends on the amount of information available on the cyclone feed slurry characteristics. Closed circuit grinding applications will be discussed in detail in this paper. The Cut Size:The size of the material in the feed which reports 50% to each product stream (i.e. underflow and overflow), after correcting for the feed solids by-passing with the underflow liquid, is termed the cut size or ""d50c"". This is often used as the criterion and the basis for cyclone design.When the corrected recovery to underflow of each mesh size in the feed is plotted against the geometric mean size in microns on a log scale, the micron size corresponding to 50% recovery is the d50c size."

Jan 1, 1992