Search Documents

"Air Products approached LAC Minerals in 1987 to initiate trials with pure oxygen in the leach circuit at several LAC facilities in Canada. This paper gives an overview of oxygen use and covers specific operating data from the Doyon and Terrains Aurifères mills near Val D'Or in northwestern Quebec. LAC also uses oxygen at the Macassa mill in Kirkland Lake, Ontario.In addition to the LAC facilities, oxygen is currently in use for test purposes at the Holt McDermott mine in Kirkland Lake, Ontario and the Camflo mine near Val D'Or.There are two requirements for oxygen in the cyanide leach mill. Firstly, oxygen is required in the familiar gold dissolution reaction as follows:(1) 4 AU (s) + 8 NaCN (aq) + 02 (aq)+ 2H 20(aq) - 4NaAu(CN) 2(aq)+ 4Na OH(aq)Of the reagents on the left side of the equation, the availability of gold is fixed by the ore in question. Obviously, water is available in excess, 1eaving cyanide and oxygen as the limiting constituents in the process. Most mills operate with an excess of cyanide, which is fairly closely monitored. Dissolved oxygen levels, however, are not normally watched very closely and find their own level based on the temperature, the availability of compressed air and the ability of the ore to consume oxygen.Typical D.O. levels are in the 3-8 ppm range, however levels less than 1 ppm are not uncommon for refractory ores.With pure oxygen, dissolved oxygen levels as high as 30 ppm can be achieved. (Figure #1). This greatly accelerates the kinetics of the leach reaction and may also shift the reaction further towards completion thus increasing gold dissolution slightly."

Jan 1, 1990

By C. Arthur Lefler

The hydrometallurgical processes for recovery of gold and silver in use at Round Mountain, Nevada and the practical aspects of the operation are discussed. Included are heap leaching by cyanidation, upgrading of solutions by adsorption of values on activated carbon and desorption (stripping) for electrowinning and subsequent refining steps to produce dore metal.

Jan 1, 1981

By Y. G. Qin

In this article an experimental study of axial bearing capacity of half-closed steel pipe pile installed at BKSH dock is presented. In comparison with open and closed end piles, half-closed end pile is considered to have high bearing capacity and good penetration, that is, it not only has a capacity as twice as the same size open end steel pipe pile, but also has blow counts as half as the same size closed end steel pipe pile. It is economic to use half-closed end pile in soft ground without a deep deposit of thick stiff clay. This article also describes a large scale model pile test and preliminarily analyses mechanism of improvement of bearing capacity of half-closed end pile with emphasis on effect of squeezed soil on side friction; an empirical approach is presented in which side friction is related to density of squeezed soil and which is useful for reasonably chosing side friction of different types of piles in design of foundarion.

Jan 1, 2010

The richer, shallower sapphire deposits of the New England region of New South Wales which have been traditionally mined by the small miner are almost worked out. Larger mining and exploration companies are replacing the small miner and exploring for the primary source of sapphire or lower grade alluvial deposits.   Although in recent years considerable exploration effort has been directed at locating the primary source, commercial exploitation of sapphire is still restricted to the working of alluvial deposits.   If the Australian industry is to compete against Asian and African producers it must use cost effective exploration, mining) processing and marketing methods.

Jan 1, 1990

The coalmining industry in most countries has, at various times, suddenly been confronted with a decrease in demand for coal. Readjustments made to reduce productive capacity to match the reduced demand for coal have often resulted in hardship to mineworkers, loss of capital investment to mineowners and loss of coal reserves. The consequences of the methods of readjustment adopted in the past have contributed to the low esteem in which coalmining has come to be regarded by a large section of the gel).eral public in many countries.Four sections of the coalmining industry, representing different periods of time, different countries, and different methods of industrial organisation have been examined:Great Britain and the U.S.A. during the inter war years, the post war European Coal and Steel Community, and post war Great Britain under the National Coal Board. An assessment has been made of the methods adopted in each case to reduce productive capacity to match a reduced demand for coal. Finally the fundamentals of the problem-as it affects the coalmining industry of any country-are considered, and possible solutions put forward.During the 1950's, surplus productive capacity was a problem in many coalmining countries, including Australia and New Zealand. As a rule no techniques are developed beforehand to solve problems introduced by a sudden decrease in demand for coal. The situation is usually tackled by a series of short term decisions based on expediency, which often in the long run only aggravate the problem.

Jan 1, 1961

By Andrew Trusiak

Brunswick Mining, employing approximately 1600 employees, is located 40 km south of the city of Bathurst in north eastern New Brunswick. The mine has operated as two lead-zinc operations - the underground mine(No.12) and the open pit mine (No.6). The open pit orebody is presently being' mined by underground methods. It is expected that the No.12 mine will furnish the entire ore supply by the end of 1981. The flotation practice prior to 1971 has been described by Neumann and Schnarr(1) and by Erskine (2). More recently, the current flotation practice has been described by McTavish(3) and deals with some major circuit modifications between 1972 and 1978. The period 1978 to 1980 has seen the completion of. a major flotation cell replacement and expansion program for the No.6 concentrator, and the implementation of computer control in the No. 12 CuPb and Zn flotation circuits.

Jan 1, 1981

Keywords: Pyrometallurgy, furnace, Lonmin, platinum, PGM, UG2 Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to its industry peers in the Platinum Group Metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that came with milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tap-block movement, the formation of three-phase ?mushy? zones, high refractory and tap-hole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to re-design Furnace No. 1, to invest in back-up furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line feed chemistry and mineralogy monitoring, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilising optical spectral analysis of the converter flame to characterise converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

By M. Arlandi, J. C. Monge

In this paper, the finite element method is used to obtain deformations of a rock tunnel. More than 3,000 numerical simulations and calculations were carried out. The analysis of this results has allowed to achieve mathematical formulations and graphs, to obtain in advance support monitored displacements in tunnelling construction, so they can be predicted before excavation and supporting woks. The application of the presented formulations and charts will aid engineers to control tunnel monitoring, reducing decision time when problems occur. The analysis is limited to cases involving elastic behaviour of the terrain for tunnels of average to good quality in rock, and to excavation sections of average or smaller dimensions for road tunnels. The results show that, in all cases, mathematical expressions to obtain induced displacements around tunnel excavations, have similar pattern than Kirsch (1898) expressions for circular excavations. As corollary of the achieved results, a method to estimate in situ natural geostress ratio K0=sh/sv , by means of convergence measurements, is presented. In diesem Beitrag wurden die Verschiebungen eines Tunnels durch die Methode de Finiten Elemente berechnet. Mehr als 3000 numerische Simulationen und Berechnungen wurden ausgeführt. Die Analyse dieser Resultate hat es ermöglicht, mathematische Formeln und Grafiken zu entwickeln, die zur Voraussage der Verschiebungen in Tunnel dienen, auch unter Betrachtung der verschiedenartigen Abstützungen. So können die Verschiebungen vor den Erdarbeiten und dem Bau der Abstützung abgeschätzt werden. Die abgeleiteten Formeln und Grafiken werden vor allem einen grossen Dienst für Ingenieure bei der Mithilfe zu zeitsparenden Entscheidungen im Tunnelbau und bei der Tunnelkontrolle leisten. Die analysierten Fälle sind auf eine elastische Modellierung des Baugrunds beschränkt, sowie auf eine mittlere bis gute Qualität des Felsens und auf die Aushebung von Abtragungsabschnitten mittlerer oder geringer Grösse für den Strassenverkehr. Die Resultate zeigen, dass in allen Fällen die hergeleiteten Formeln zur Berechnung der durch den Tunnelbau verursachten Verschiebungen um den Tunnel die gleiche mathematische Struktur haben wie diejenigen von Kirsch (1898) für kreisförmigen Bodenaushub. Als Korollarium der ausgeführten Berechnungen wird eine Methode zur Abschätzung der vorherrschenden in situ Geospannungs-Verhälniss K0=sh/sv angegeben, die von den Messungen der Verschiebungen im Tunnel ausgeht. Dans cet article, la méthode des éléments finis est utilisée pour obtenir les déformations d’un tunnel creusé dans la roche. Plus de 3000 simulations numériques et calculs ont été effectuées. L’analyse de ces résultats a permis de définir des modèles mathématiques et des abaques afin de prédire, avant l’excavation et les travaux de soutènement, les déplacements auscultés pendant la construction du tunnel. L’application de ces modèles et abaques permettra donc aux ingénieurs de contrôler les déplacements durant l’auscultation du tunnel et de réduire le temps de décision lorsque des problèmes surviennent. L’analyse est limitée au cas du comportement élastique du terrain pour des tunnels creusés dans de la roche de moyenne a bonne qualité, et à de sections d’excavation de petites à moyennes dimensions pour des tunnels routiers. Les résultats montrent que, dans tous les cas, les expressions mathématiques permettant d’obtenir les déplacements induits autour des excavations de tunnel, présentent des similitudes avec celles de Kirsch (1898) pour des excavations circulaires. Comme corollaire aux résultats obtenus, une méthode pour estimer le rapport des

Jan 1, 2003

By Ben Hayes, Michael Ryjevski

The Palm Jumeirah is the smallest of the three Palm Islands (Palm Jumeirah, Palm Jebel Ali and Palm Deira). It is located on the Jumeirah coastal area of the emirate of Dubai, in the United Arab Emirates (UAE). The unique man made island is built in the shape of a date palm tree and consists of a trunk, a crown, 17 fronds and a surrounding crescent island that will form a breakwater. The Jumeirah Palm Island is primarily are treat and residential area for living, relaxation, and leisure. It will contain themed boutique hotels, three types of villas, shoreline apartment buildings, beaches, marinas, restaurants, cafes and a variety of retail outlets.

Jan 1, 2007

By J. de Villiers

Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine analysis. The method, however, requires a good initial calibration and periodic checks on its precision and accuracy. Several examples from minerals processing, pyrometallurgy, and materials science show the strengths and applicability of the method. The limitations and sources of error are also discussed.

Jan 1, 2007

The need for the hydraulic transportation of coal in the New South Wales coal industry, both from the coal face to the surface and from the coal mine to the consumer or the port for export, is explained. Details of research projects currently in'progress and involving the hydraulic transportation of New South Wales coals are given together with information on the hydraulic transportation of coal in the United States of America.The potential of hydraulic transportation as a viable alternative to the proposed expansion and upgrading of the New South Wales railway system to meet the projected New South Wales coal production to the year 2000 is described.

Jan 1, 1980

By S. Rivard

"This paper demonstrates the selection of grinding circuit technology for a number of recent projects including discussion of the key drivers and the role of energy efficiency. Decreasing head grades combined with a strong and sustained increase in operating costs has forced miners to examine increased project size, increased equipment capacity and efficiency improvements in order to reduce their unit operating costs and improve overall project economics. Comminution energy consumption, safety and capital cost considerations play a critical role in the success of projects. This paper presents some key guidelines for a successful and cost effective comminution circuit design and includes a case study on three projects, outlining the issues and the drivers which led to the ultimate circuit selection and the critical role that energy efficiency played.IntroductionComminution circuits for minerals processing are selected based on their suitability and efficiency in reducing run-of-mine ore to the desired feed size for the downstream process. The input material (ore) properties and downstream process requirements are the key determinants and there are standard approaches for each circumstance.The minerals processing industry has been a fast adaptor of efficiency improvements based on increasing capacity of equipment (e.g. trucks, crushers, mills, pumps) but less successful in adapting radically new technologies that disrupt incumbent flowsheets or processes.The installed power of grinding mills has increased linearly over the past 25 years (Meka & Lane, 2010) and pumps and classification equipment have kept pace. The autogenous grinding (AG) and semi- autogenous grinding (SAG) mills displaced stage crushing as a dominant method of coarse rock breakage in many applications causing crusher manufactures to increase the capacity of cone crushers to meet the competitive demand.Examples of new comminution technology in the 20th and 21st centuries are the development and adoption of cyclone classification in the 1940s (Newtech, 2016), AG milling in the late 1950s, vertical grinding mills in the 1980s, high pressure grinding rolls (HPGRs) also in the 1980s and ultrafine milling technology in the 1990s (Meka & Lane, 2010)."

Jan 1, 2017

By Madgwick J. C

The monosaccharides glucose, galactose and arabinose, and the polyols glycerol and mannitol (0.1 Ufo WIV) supported pure and mixed culture heterotrophic bacterial manganese leaching of solid pyrolusite (MnO2, 2% W/V) to yield 14-38 mg/litre manganous ion in 3 days from a simple mineral salts media at 30°C. Supplementation of pure bacterial isolates growing on glucose with soluble intracellular photosynthate from freshwater algae (0.07 g/l carbohydrate) and marine algae (0.11 g/l) led to an improvement in Mn++ yields of 24 and 100 per cent respectively. Extracellular products of the freshwater algae (0.3 g/l carbohydrate) boosted recoveries by 57 per cent.

Jan 1, 1982

By A. C. Smith

Although only used in a few U.S. longwall mines, bleeder-less ventilation systems can be an effective spontaneous combustion control method in mines having a demonstrated history of spontaneous combustion. To provide insights for the optimization of bleederless ventilation systems for U.S. underground coal mines, a computational fluid dynamics (CFD) study was conducted to model the spontaneous heating in longwall gob areas using a bleederless ventilation system. A single longwall panel with a bleederless ventilation system was simulated, and typical longwall mine ventilation data were used in the simulations. The permeability and porosity profiles for the longwall gob were estimated using a geotechnical model and were used as inputs for the CFD modeling. The effects of gob permeability and resistance of the collapsed entries on the spontaneous heating were studied. The effectiveness of using nitrogen injection to prevent spontaneous heating in the gob was also examined.1

Jan 1, 2008

By Nathaniel Arbiter

Flotation’s earliest patent was issued in 1860. However, the process was first applied commercially in Australia until 1904, and in Montana in 1911. Major advances followed both in reagent treatment and in cell design, with resulting process improvements. Mechanical cells have seen the widest use and with the major increases in plant capacities (Fig. 1) their volumes have also increased (Fig. 2). In 1991, the principal use for the process was to produce copper concentrates for smelting. It was applied to 243 Mt (268 million st) of copper ore. The total of all ores floated that year was 426 Mt (470million st). In 1997, US mines produced 257 Mt (284 million st) of copper ores for flotation, yielding1.75 Mt (1.94 million st) of copper.

Jan 1, 2000

By S. L. George

The semi-solid metal casting process results in a unique solidification path. The microstructural features that were identified during the characterization of the as-cast microstructure, were used as evidence of the process history in order to determine the solidification path followed during the evolution of the microstructure. The morphology of the grains was characterized using SEM and the extent and distribution of the elemental segregation within the grain structure was analysed using EDS. Keywords Semi-solid casting, solidification path, segregation.

Jan 1, 2011

By Paul Gauthier

Aujourd?hui, avec un faible prix de l?or sur le marché, les opérateurs miniers doivent revoir leur façon de faire. La méthode de minage «Eureka» permet de réduire les coûts de production et d?accélérer la mise en production des chantiers. Les principales étapes du cycle de minage et les problématiques associées à l?utilisation de cette méthode à la Mine Bousquet y sont décrites.

Oct 1, 2001

By Rodney Ishak, Merete Tangstad

In the HC FeMn production, better utilisation of coke and electric power is vital for reducing the production costs. The higher manganese oxides in the charge are reduced to MnO in the prereduction zone, where also the Boudouard reaction is active. These gas-solid reactions are to a large extent decisive for the total consumption of both coke and electrical power in ferromanganese production. In the present work formulas for calculating the Degree of prereduction have been developed for industrial practice. It shows that the typical Degree of prereduction is between 10-40%, but it may in good periods be as high as 60%. Statistical analysis has been done in order to find how various operational parameters influence the Degree of prereduction. A few parameters were observed to have an effect on the prereduction. Comilog ore definitely had a positiveinfluence on the prereduction, Comilog sinter and Mamatwan ore probably had a positive influence on the prereduction, all in relation to the average prereduction in the selected periods. Meanwhile, As man ore definitely, % H2O in raw materials and increasing Hd probably, had a negative influence on the prereduction. The findings for these raw materials were very much in coherence with the results of laboratory scale experiments performed, where the CO-reactivity of different ore materials was studied.

Jan 1, 2007

By J. E. Conley

[Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly in the form of byproduct salt cake from the acid manufacturers, has been tending to decease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft-paper industry, especially in Lie South, has brought about greater demand for sodium sulphate in that section. This demand is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorably situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far re¬moved from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4?10H20), which must be dried or dehydrated in order to most consumer requirements. The waters of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting even the dehydrated product to market is the deciding economic factor. Therefore, the recovery or production of anhydrous sodium sulphate from plant-waste liquors or from natural brines of suitable composition might be economically feasible.]

Jan 1, 1936

By Hani Mitri

Understanding the interaction between rock bolts and underground rock movement is critical for safe and cost effective underground excavation design. Although early research on this subject involved a balance of theoretical analysis and field measurement, recent work has been heavily focused on analytical and numerical studies. This paper describes technologies that have the potential to redress the balance through instrumentation of rock bolts deployed under routine operating conditions in underground mines. Two new products are presented in this paper. Firstly the U-cell coupler is a load cell device that can be routinely coupled to the threaded end of a bolt prior to installation. It measures the ?series? load at the head of the bolt. Secondly, the d-REBAR involves an array of small-diameter, long-base length displacement sensors recessed into grooves along the entire length of the bolt. Both new instruments are interfaced with on-board digital signal conditioning and telemetry. Methodologies for the deployment of the new instrumentation and guidelines are presented for the interpretation of results based on data obtained from field trials. Successful field installations demonstrate the viability and practicality of these new technologies and, moreover, provide important insight in to rock bolt/rock mass interaction.

Jan 1, 2012