Search Documents

By N M. Vegter, C B. Kohler, E H. O Meyer

Zincor operates four Lurgi fluidised-bed roasters at its roast-leach-electrowin refinery in Springs, South Africa. In 2006, Zincor?s four roasters had reached ages ranging between 26 and 38 years, while the expected life of this type of roaster is generally 20 to 25 years. Based on its condition, Roaster 3 was the first to be rebuilt in 2006. Roaster 4 is being rebuilt in 2007 and the last two roasters will be rebuilt over the next few years as necessary. The main damage to Roaster 3 was caused by buckling of the roaster steel shell. This caused the freeboard and dome areas to shift, resulting in cracks in the dome brick lining and crumbling of the bricks lining the freeboard. The steel shell buckled due to the combined effects of too-high operating temperatures and corrosion caused by the following two main factors: ? Thicker external insulation was installed during a previous maintenance shut which resulted in and increased steel shell temperature and exacerbated the normal metal fatigue; ? SO2/SO3 containing gas that had permeated through the brick lining, passed through its dew point during frequent planned and unplanned shuts over the life of the roaster. This caused acid formation between the refractory brick lining and steel shell, resulting in corrosion of the shell. The initial plan was to replace only the damaged areas of Roaster 3, but upon dismantling more damage was found and the roaster was rebuilt from the tuyeres upwards. During the rebuild, the opportunity was taken to modify the design of some of the brickwork to extend its life and make future repairs easier. This paper discusses the mode of failure of Roaster 3 and the lessons learnt during its dismantling and rebuilding.

Jan 1, 2007

Continued market pressure on the US coal industry was the overriding factor affecting developments in underground mining in 1986. An oversupply of coal in the spot market kept prices low throughout the year and caused a number of operations to close their doors. Operators stepped up their efforts to improve productivity at existing operations. They made technology advances and improved their relations with employees. A continuing market-related development during 1986 was the divesting of coal properties and operations by major oil companies, which were faced with economic pressures in both the oil and coal industries. Further increases in contract mining production resulted as some larger operators were unable to compete in a tough economic environment. Longwall mining is still seen by many as the technology that will provide the necessary productivity to remain cost-effective. But the number of active faces in the US declined in 1986, as reserves were depleted and economics forced some closures. At the first Longwall USA meeting in June, much attention was placed on improved technology, as electro-hydraulic controls for roof supports gained acceptance. Other recent developments include shearer initiation of roof supports, automatic horizon control for shearer drums, and collection and storage of machine data for predicting maintenance requirements. The government and academic communities continued their research on dust control at longwall faces. Jankowski, Kissel, and Daniel, (October 1986, Mining Engineering), gave an overview of progress in longwall dust control. And Mukherjee, Singh and Jayarman (November 1986, Mining Engineering), recommended design guidelines for improving water spray systems for dust control. Surface subsidence Increasing attention is being given to surface subsidence. This is primarily because of longwall mining and the Surface Mining Control and Reclamation Act. Improved methods of prediction of surface subsidence, especially computerized methods, are being continually developed. Mining engineering faculty at major universities such as Virginia are helping develop public policy and regulations concerning subsidence. As part of this effort, Unrug and Johnson identified major subsidence areas of Western Kentucky. Peng and Chen (February 1986, Mining Engineering), gave an overview of history and research of surface subsidence. And Elifrits and Aughenbaugh, (February 1986, Mining Engineering), discussed effects of moisture variations and overburden on subsidence. This research culminated in a Symposium on Surface Subsi¬dence at the SME 1986 Fall Meeting in St. Louis and the 2nd Workshop on Surface Subsidence at West Virginia University. Ground control in coal mining continued to be an item of major research interest. Some 30 papers were presented at the 5th International Conference on Ground Control in Mining at West Virginia University. And six sessions were related to coal mining at the 27th US Symposium on Rock Mechanics at the University of Alabama. At the 4th Annual Workshop, Generic Mineral Technology Center, Mine Systems Design and Ground Control emphasized efforts of the participating universities to improve ground control. Peng and Chiang summarized results of studying support capacity and roof behavior with longwall shield supports. And Unrug, Johnson, and Nandy analyzed the process of deterioration of shale roof in a case study of a room-and-pillar coal mine. The importance of geologic conditions in determining mining productivity is receiving increased attention in coal mine design in the US. Mullenex related, through case studies, the benefits to be derived through analyzing the depositional system of coalbeds as an integral part of mine design. Improved technology in this area was related by Lloyd, Semborski, and Stolarczyk. They discussed a case study of using radio imaging to indicate coal-seam discontinuities in advance of mining. Improved coal mining technology in general is being researched more heavily, to help improve US coal competitiveness. However, much of this research and development process has yet to be widely implemented. Equipment manufacturers are devoting more resources to development of continuous-haulage systems, mobile roof-supports, mine-monitoring systems, and predictive-maintenance systems using computers to extract machine data.

Jan 5, 1987

By J. W. Thompson

OIL AND GAS AS MINERALS. Oil and gas within the ground are minerals and the fact that they have attributes not common to other minerals because of their fugitive nature or vagrant habit, and the disposition to percolate, and the possibility of their escape from beneath one part of the surface to another, does not remove them from the class of minerals. Texas Co. v. Daugherty (Texas), 176 Southwestern, 717, p. 719, May, 1915. OWNERSHIP OF TAILINGS-ABANDONMENT. A corporation engaged in milling- and the reduction of ores deposited the tailings therefrom upon a portion of its own land lying in a gulch through which water flows at times in great volumes and with great force' and notwithstanding all reasonable efforts by dams and otherwise to retain its tailings, the tailings eventually were forced upon the lands of an adjoining owner; these tailings were valuable and their retreatment, intended by the mill owner, profitable; and the fact that the tailings were so washed down upon the lands of the adjoining owner and permitted to accumulate and remain for some considerable time is not sufficient to show an abandonment on the part of the owner of the tailings, where it is clear that the owner had no intention of so doing, but on the contrary, always intended to conserve and retreat the tailings.

Jan 1, 1916

By Yasushi Sawada

An experimental investigation was carried out to study the rates of reduction of iron oxides dissolved in liquid Ca0-SO2-A203 slags by Fe-C droplets at temperatures ranging from 1325 OC to 1550 OC. The %FeO in the slag was varied from 5.5 to 18. Flash X-ray images were employed to observe the behavior of Fe-C droplets in the slags during the reactions and for determining the slag-gas-metal interfacial area. Effect of P205 in the slag and sulfur in the droplet was also investigated. The reduction rates were determined by measuring the volume of CO evolved as a function of time and the estimated slag-gas- metal interfacial area. The reduction rates have increased with increasing %FeO in the slag and the slag temperature. The experimentally established relationship between the reduction rates and FeO (wt%) in slag is given by

Jan 1, 1992

By C. Mosoane

ERPM was formed in 1893 and as a result of its age, a large volume of data exists in a paper-based format and it was decided to electronically capture data in one of two critical mining areas?namely at Far East Vertical (FEV) Shaft Area (Lower Areas) and Hercules Shaft Area (Upper Areas). The life of mine is dependent on tonnage and grade from these areas. Geostatistical evaluation of the gold reserves has been applied on an ad hoc basis in the Hercules Shaft Area and on a continuous basis in the FEV area. This is the first evaluation using geostatistics that was performed on the Upper Areas. This paper is based on the premise that regardless of cut-off grades, geostatistical estimation (kriging) estimates and locates reserves better than ?traditional? methods e.g. polygonal method, inverse squared distance method and it endeavours to estimate and locate the high grade reserves in the Main Reef Leader of Upper Areas.

Jan 1, 2003

By V P. Elpatyevskaya, V S. Arzhanova

Main geochemical problems concerning the environment and mining industry interrelation are connected with the transformation of natural water chemistry by mining wastes. The investigation of many mines in Primorye, the southern part of the Russian Far East, showed that their mining waters have high concentrations of heavy metals and aluminium. Water acidity is primarily connected with the amount of acid-forming sulphide minerals in ores and also depends on the neutralising capacity of rocks. Considerable quantity of metals occur in the waters in dissolved form. Metal concentrations in mining waters exceeds the natural levels by two to five orders of magnitude and can't be reduced to the background levels even after multiple dilution. It is necessary to develop and put into practice new technologies so that to reduce the geochemical impact upon the environment.

Jan 1, 1995

By D. D. Runnells

This study focused on the chemical reactions between uranium tailings fluids and cores of subjacent bedrock from the site of the Cotter Corporation uranium mill at Canon City, Colorado. Actual and synthetic tailings fluids were forced through cores of bedrock. The pH of the effluent solutions was the dominant control on the behavior of dissolved species in solution. The pH depended on the presence or absence of calcite cement in the rocks. Calcite neutralized acidic raffinates and caused the precipitation of iron, manganese, aluminum, and possibly uranium. Chloride, sulfate, and sodium were not retarded upon passage through the cores, and sulfate and chloride should be useful as tracers of escaping tailings fluids. Zinc, copper, cobalt, nickel, uranium, and vanadium exhibited high mobility under acidic conditions and were strongly retarded at elevated pH. Calcium was released due to dissolution of calcite and ion-exchange. Magnesium was not retarded in concentrated solutions, but showed moderate retardation in dilute fluids. Potassium and ammonium both showed early retardation followed by breakthrough and mobility. The behavior of molybdenum was strongly dependent on pH, with retardation at low pH and mobility at elevated pH. Selenium was highly mobile under all conditions. Selenium should be a better tracer than molybdenum for many situations. Precipitation of carnotite appears to control the solubility of uranium and, possibly, vanadium. With the exception of the precipitation of aluminum and silica, all reactions were rapid.

Jan 1, 1983

By Y. Nien Wang, Moe Amini, Heiner Sander, Max John

INTRODUCTION As the population increased along the coast route (California Route 1), and the people’s need to have guaranteed access increased, the landslides and related road closures began to have serious adverse economic impacts. Landslides were causing major long-term road closures about every 10 years on average. In 1983, ground movement at Devil’s Slide caused Highway 1 to be closed for an extended period of time which caused significant economic loss to the surrounding coastal communities. A number of options for bypassing the slide area were considered, and the Martini Creek inland bypass was selected for design. Subsequent litigation led to the creation of the Devil’s Slide Tunnel Study in 1996. The results of this study indicated that a tunnel alternative would be competitive with the inland bypass. The final decision was left to the citizens of San Mateo County, who approved the tunnel alternative in the November, 1996 election After completion of environmental studies and the processing of legal challenges, the final environmental document was finished in 2001. The preferred tunnel alternative was designated to proceed for final design and construction. PROJECT DESCRIPTION The Devil’s Slide Tunnels consists of a separated two-lane road, one lane in each direction, which passes through twin tunnels and over twin bridges and then connects with the existing non-separated, two-lane road at each end. The total length of the project is approximately 1900 meters consisting of four main project divisions, which are described below, going from south to north. 1.Operations and Maintenance Center (OMC) area, 2.Southern approach roadways to the South Portals (250 meters), including the South Rock Cut,

Jan 1, 2005

By P. Fawell, C. Castillo, C. Ihle

"The need to reduce fresh water consumption has pushed many Chilean mining companies to utilize seawater obtained from distant locations. At the same time, increasing amounts of fine particles in copper tailings raise new operational challenges, in particular, the thickening and transport of tailings featuring significant fine fractions, which are predominantly clays. In the present paper, we study the role of salinity – using seawater and NaCl – on the flocculation efficiency of copper sulphide tailings to which kaolinite was added. To mimic the water recovery stage in thickeners, flocculation has been induced in jar tests and the corresponding aggregate size distribution has been estimated from chord length distribution data obtained using a focused beam reflectance measurement (FBRM) probe, at various mean turbulence intensities. Results show that for constant flocculant dosing, a measurable influence of the salt on the resulting aggregation exists. For each case, resulting optimal turbulence levels are also reported, a particularly interesting feature when comparing flocculation efficiency of the coarse and fine fraction. INTRODUCTION The concentration of copper minerals through comminution and flotation is intensive in the use of fresh water. The need to reduce the consumption of fresh water and the environmental standards associated with increasingly demanding mining operations have driven improvements in the techniques of recovering water from tailings. The challenges are even greater when required to treat minerals with high clay contents. In Chile, kaolinite is one of the most important clays to consider due to its abundance in the tailings from many operations. The most common and highest throughput unit operation in the mining industry for the recovery of water from tailings is gravity thickening, with sedimentation of fine particles assisted by flocculation. Flocculation is the process of forming aggregates by contacting the suspended particles with a flocculant. The flocculant is typically a water-soluble synthetic long-chain polymer, where copolymers of acrylamide and sodium acrylate are the most common types used in the Chilean mining industry. The aggregation mechanism includes the following key steps: (1) flocculant distribution through the suspended particles, (2) flocculant adsorption onto particle surfaces, and (3) collisions between particles leading to polymer bridging to form aggregates, but concurrently (4) breakage of aggregates becomes a factor under prolonged shear (Gregory, 1988)."

Jan 1, 2018

By David L. Bickel

The following instructions and descriptions are presented in two parts to assist an individual to make the borehole deformation gage transducer, and to assemble and test the three-component borehole deformation gage. This Bureau 8 of Mines three-component borehole deformation gage (4, 8, 11)2 fits in a 1-1/2-in-diameter borehole that is drilled in rock and then overcored to determine rock stress.

Jan 1, 1978

By Thomas M. Barczak

This U.S. Bureau of Mines report chronicles the historical development of longwall mining in the United States and speculates on future developments to the turn of the century. The involvement and contributions made by the Bureau during these developments are also discussed. Two major periods of history are analyzed: (1) from 1875 to 1950 when small advancing faces were operated manually, and (2) from 1950 to 1990 when mechanized extraction and powered roof supports provided a system to efficiently extract large coal panels. Five eras of technological development during the modern period are described and analyzed. These eras discuss the development of (1) mechanized extraction, (2) powered roof supports, (3) high-capacity roof supports, (4) shield supports, and (5) system automation. Current trends are analyzed in terms of longwall utilization, face production, support capacity, face widths, and new technological developments. From these analyses, the future of longwall mining to the year 2000 is speculated. It is concluded that longwall mining will continue to grow in importance during the next decade and that the next major technological milestone will be the realization of a fully automated longwall mining system.

Jan 1, 1992

The relative abundance of coal in India compared to other fossil fuels makes it a natural choice as the primary source of fuel, be it for steel making, power generation or for other uses. The wide variations in nature and type of Indian coals formed during lower Gondawana period and categorized as difficult-to-wash due to its typical mineral matter association with the organic matrix call for suitable beneficiation techniques as the preferred option for quality upgradation. The good quality coking coals of the upper seams are fast depleting leaving behind the inferior quality lower seam coal. The lower seam coals presently being mined are mostly low volatile coking coal (LVC). They constitute about 50% of the total coking coal reserves in India. The beneficiation of Low Volatile Coking coals pose a major challenge and detailed R & D studies was taken up to study the beneficiation characteristics of these coals. The studies revealed that the liberation characteristics at coarser sizes are very poor and the coal is to be ground to finer sizes for liberation. The most important factor that determines coal cleaning efficiency is liberation of organic matter from mineral matter. To achieve liberation grinding is necessary as a result range amount of ultra fines (-0.063 mm) coal is generated. Presence of these large amount of ultrafine in the coal fines, often impose severe technical constraints affecting not only its floatability but also in the downstream treatment of the products like dewatering and cake formation particularly when it is beneficiating through froth flotation. In the present paper optimization of ultra fines (-0.063 mm) has been tried for a LVC coal of Jharia coal field for the better liberation and beneficiation of the above coal fines. It is observed that by optimized, combination of size and number of balls generation of fines can be controlled with liberation. Keywords: coking coal, liberation, floatability, dewatering

Sep 1, 2012

Bateman Engineering managed the establishment of a second diamond treatment plant at the Letseng Mine in the Mokhotlong District of northern Lesotho, about 100 km from the town of Buthe Buthe. Letseng Diamonds Proprietary Limited, is owned 70 % by Gem Diamonds and 30 % by the Government of the Kingdom of Lesotho. The second plant, which commenced construction in late 2006, doubled Letseng Mines' hard rock processing capacity from 2.6 million t/yr to 5.2 million t/yr, making it the worlds' seventh largest diamond mine by throughput. Bateman Engineering provided the engineering design, procurement and construction management of the new plant.

Jan 1, 2010

By S. Kelebek, J. A. Finch, Zhenghe Xu, S. R. (Ram) Rao

To improve SO2 emission compliance, pyrrhotite from Sudbury copper-nickel ores is being depressed with DETA. To understand the mechanism of depression, the role of complexing in controlling metal-ion activation of pyrrhotite was investigated. DETA was found to remove Cu and Ni ions but leave hydrophilic ferric species on the pyrrhotite surface. The metal:DETA ratio appeared to be 1:2. Cu was more readily removed than Ni, but the combination of DETA with sulphur dioxide was equally effective for both metal ions. Certain combinations of DETA, Ni ions, xanthate and dithionite (S2O4) or dithionate (S2O6), as representative derivatives of SO2 in water, produced hydrophilic precipitates. These may enhance pyrrhotite depression

Jun 19, 1905

By John K. Alley

Despite the extensive use of fluorphlogopite, investigators do not agree as to its exact melting temperature. Data on other fluormicas and on related fluorsilicate systems are largely nonexistent. A knowledge of the melting temperature is necessary for the effective synthesis and use of fluorphlogo¬pite or other fluormicas. The increasing use of two- and three-mica systems to yield polycrystalline ceramics has made more urgent the need for melting temperature information concerning these other fluormicas. This report is part of a program by the Bureau of Mines to synthesize large-size or large-crystal fluorphlogopite and develop a usable reconstituted fluormica sheet. The melting temperature of fluorphlogopite, K2Mg6A12Si6020F4, was found to be 1,383° ±2° C. This temperature was found by studying single crystals of fluorphlogopite, heating behavior of glass of fluorphlogopite composition, and the actual crystallization of fluorphlogopite from a melt that had been heated above 1,430° C. The formation of forsterite or norbergite was directly proportional to the loss of volatiles during the experimentation. Many trials revealed that the only reliable seal was a thick platinum sheet with welded seams. If no volatiles were lost, neither norbergite nor forsterite were formed; fluormica was then the only product. Excellently formed crystals of forsterite with an optical sign different from ordinary forsterite were obtained during the single crystal melting experiments. These crystals resulted from a slow loss of volatiles. A congruent melting of fluorphlogopite is indicated by the data of this report; however, incongruency within a small temperature range is not precluded. A more refined method using phase equilibria-quench methods would be necessary to settle the question absolutely.

Jan 1, 1962

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By W. James Marold

The New Croton Aqueduct (NCA) was the first major water supply tunnel for New York City. The 50-km (31-mi) long tunnel has 33 open shafts 6 m (20 ft) to 121 m (397 ft) deep. The tunnel and shafts are lined with brick and mortar, with cast iron lining and pressure covers in six pressurized shafts. Details of the 1895 construction are provided and compared to modern construction techniques. The paper provides rehabilitation techniques for the shafts and pressure covers, including grouting, epoxy lining, temporary bulkhead design and installation and placement of tremie concrete 98 m (320ft) below the water level in a 122 m (400ft)deep shaft using a Remote Operated Vehicle (ROV) to monitor the placement.

Jan 1, 2008

By J. W. Thompson

A contract stipUlating for the delivery of quantities of phosphate rock" f. o. b. mines," and stipUlating that" while this contract is in form an absolute sale for a fixed quantity in each year, it is mutually understood and agreed that the purchase is for the buyer's consumption and not for a sale; the buyer agreeing to give to seller the refusal of any surplus over and above the actual consumption. Buyer is at liberty to increase or diminish the quantity called for in any year, to the extent of not exceeding 10 per cent; provided that the quantity to be taken shall not be less than buyer's consumption; provided further that notice of such increased or diminished demand be given seller 12 months in advance of such change," is to be construed as a contract for the sale of stated quantities of rock, deliverable in approximately equal quantities during each year for the specified series of years, subject only to be increased or diminished after specified notice in any year, where the amount taken would not be les<; than the buyer's consumption, not exceeding 10 per cent, and the contract indicating that the rock was intended by both parties for consumption in the fertilizer plant of the buyer. but the quantity to be taken was not limited by the necessities of' the plant.

Jan 1, 1916

By R. W. Smith

Many industries such as the cement industry handle large quantities of limestone and clay slurries. However, at present very little is known about the flow properties, such as friction loss due to flow of slurries in pipelines. This lack of knowledge has made it often very difficult to calculate the total dynamic head of a proposed slurry handling system, and therefore has often made the selection of correct size slurry handling equipment difficult. Because of lack of knowledge about slurry flow a study of slurry flow theory has been made at the Portland Cement Association&apos;s Research and Development Laboratory with the idea of developing a method whereby friction losses due to slurry flow may be predicted for any size pipeline. The flow equations developed have been checked by pilot plant size equipment. DERIVATION OF FLOW EQUATIONS It has been known for some time that limestone and clay slurries handled in cement plants do not flow in the same manner as a Newtonian fluid such as water. When a Newtonian fluid flows the shear stress at any flow velocity is proportional to the rate of shear. This phenomenon can be illustrated by a line (Figure 1). The viscosity of the fluid is the slope of the curve. Thus, the flow properties of the material may be characterized by a single materials constant: viscosity. When a non-Newtonian fluid with the type of characteristics exhibited by limestone and clay slurr-ries flow, a similar curve can be constructed (Figure 2). This graph is a shear diagram of a Bingham plastic non-Newtonian fluid. It should be noted that with the Bingham(1) plastic type of flow viscosity, the slope of the curve, is still an important materials constant. In addition, however, there is another materials constant, namely the yield stress of the material. One way to visualize this constant is to consider it as the amount of energy that must be put into a Bingham plastic material to start it flowing.

Jan 1, 1961

By John Trefny

Although mining is currently one of the smallest academic units on the Colorado School of Mines(CSM) campus, it is alive and well, with nearly 100 undergraduate and graduate students. For many years, Mines has had undergraduate and graduate programs in hard-rock mining. The school has recently transferred its physical mineral processing activities to the Mining Department. The program has also expanded to include tunneling, underground construction and industrial minerals. There are current discussions about increased research activities on cement and other construction materials. The Mining Department also teaches its share of what is called the “distributed core” courses with curricular requirements common to related programs, as well as mining safety and health, in conjunction with our continuing education department.

Jan 1, 2002