Search Documents

By A. Gene Collins

Potassium, lithium, strontium, barium, and manganese are present in many oilfield brines, None of them except barium is determined routinely in brine analyses. Therefore, sensitive and accurate flame-spectrophotometric methods were developed. Potassium, lithium, and strontium were determined by a standard-addition technique in ethyl alcohol solutions. Barium and manganese were determined in ethyl alcohol and normal propyl solutions, respectively, after interfering substances were removed.

Jan 1, 1962

By Eric E. Unger

Results are presented of a census of the machines used in surface coal mines in the United States. The numbers of each machine type and model reported to be in use are tabulated for large and small mines in the Eastern, Central, and Western regions. Also tabulated are the average daily usage times of the major machine categories and the numbers of machines that have acoustical and other cabs. Projections of the total numbers of primary production machines are given. It is found that heavy tracked dozers and wheeled front end loaders constitute the most prevalent machine types, and that generally a very few models of machines made by one or two manufacturers constitute a major fraction of the population in each machine category. About 70 percent of all machines are reported to have some kind of cab, and about half of these are reported to be acoustical gabs; it is noted that acoustical cabs generally came into significant use since about the early 1970's. It is observed that the percentage-wise mixes of equipment types used in the various categories of mines differ significantly for only a few types of machines, notably for heavy dozers and loaders, and for haulers, highway trucks, and internal-combustion engine-powered shovels and draglines.

Jan 1, 1977

By S J. Neethling and, S J. R Simons

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, have been investigated. In this study two bubbles of equal size were formed and forced to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. Data of coalescence frequency and time is presented, as well as images of the coalescence events. The coalescence frequency was used to validate a parameter, Pf, known as the film failure frequency, used in a simulation model to predict foam height in a gas-sparged vessel. Predictions determined using Pf were then validated by experimentation.

Jan 1, 2005

By Gerald C. Dohm

INTRODUCTION After a mining company has discovered a mineral deposit, the problem is then how to mine and process that deposit the best way. The principal problem facing managers or engineers who must decide on mine plant size, equipment selection, and long-range scheduling is how one can optimize a property not only in terms of efficiency but also as to project duration. Mine opti¬mization is dependent upon the interaction of con¬tributing parameters which leads to maximizing the net present value (NPV) Realistic mine planning is the key, to the analysis. The process is to be used when evaluating undeveloped properties or when a complete revamping of existing facilities is scheduled The proc¬ess is not intended for detailed mine design but rather for property evaluation and feasibility studies. The derivation of the various input parameters will only be discussed to the point where a meaningful correlation can be made with the overall analysis. The interrelationship of the parameters will be the central point because most company guidelines and financial analysts have their own standards when deriving the various inputs. Assume that the data is totally acceptable and pro¬vides at least the following categories of information and guidelines- (1) mineral and waste inventory; (2) geologic, hydrologic, and geotechnical criteria; (3) topographic layout including property boundaries; (4) metallurgical flowsheet, recovery and design criteria; (5) access, water, power, and environmental base-line study; and (6) financial constraints (minimum rate of return, payback period, etc).

Jan 1, 1979

By Tatiana Salviano Gadelha

Rejeitos de mineração descartados na forma de polpa possuem, geralmente, grande quantidade de água e reutilizá-la no processo, por meio de operações de desaguamento mais eficientes é de grande importância para a implementação de projetos de menor impacto ambiental. O presente trabalho visa estudar as operações envolvidas no desaguamento de um rejeito de níquel, com o objetivo de principalmente a maximizar a recuperação de água de processo. Para tanto, foram avaliados: a influência da concentração de sólidos, uso e dosagem de floculante, pressão no filtro, o processo de filtração com e sem prensagem e a influência destas variáveis na umidade da torta e na recuperação de água. Os resultados mostraram que quanto maior a dosagem de floculante menor é a recuperação de água na filtragem; por outro lado, quanto maiores a concentração de sólidos e a pressão, maior a recuperação de água. Verificou-se a importância do uso da prensagem para maximizar a recuperação da água contida no sedimento, sendo possível comprovar que o rejeito de níquel floculado e filtrado com ?P de 6 bar com o uso de prensagem promoveu a recuperação de até 77% de água.

Aug 17, 2017

By Kevin Hennings

Screening efficiency models developed to date rely almost exclusively on empirical formulas based upon large amounts of acquired operating data. A screening model was developed using a combination of empirical coefficients and explicit mathematical expressions which quantify screening phenomena. A series of screening tests was run to supply data for purposes of correlation and empirical coefficient evaluation. The model has been implemented as a digital computer program. The validity of the modeling procedure has been established by laboratory testing. Results generated by the model have been used to compile an applications handbook, which can be used to predict screening performance in lieu of using the computer program.

Jan 1, 1982

By Masami Hayashi

The Bureau of Mines conducted laboratory studies to investigate methods for desilicating sodium aluminate solution derived from leaching a limestone-anorthosite sinter with 10-pct Na2C03 solution. Desilication tests were made at atmospheric pressure to determine the effects of time and additions of lime and desilication residues. A two-stage, countercurrent desilication procedure was developed to reduce the Si02 content sufficiently to meet specifications for cell-grade A1203. Both stages were conducted at boiling temperatures at atmospheric pressure. Reagent lime was charged as desilication seed to the partially desilicated solution in the second stage, and a product (desilication residue) precipitated by the lime addition was charged to the freshly leached solution in the first stage. Average A1203 loss in the desilication circuit was 5.8 pct, and the product solution contained less than 0.04 g/l Si02. Complete precipitation of A1203 by carbonation resulted in a hydrate containing less than 0.01 pct Si02. Calcination of this hydrate would produce A1203 meeting the 0.015 pct Si02 specification for cell-grade material.

Jan 1, 1982

According to the Darcy?s law, filtration rate should increase with increasing pressure drop (?P) across a filter cake. In centrifugal filtration, ?P is created by the free water present on the surface of a filter cake. Thus, ?P can become negative when the free water disappears from the cake surface, which makes it difficult to achieve low cake moistures. In the present work, we have developed methods of overcoming this problem by either increasing the air pressure inside or applying vacuum outside a centrifuge. Laboratory dewatering tests conducted using these provisions showed that the moistures of various minerals and coal fines can be reduced to the level that can obviate the need for thermal drying. The new concept has been successfully tested both at pilot- and full-scale, which lead to commercial deployment through Decanter Machine, Inc., under the trade name Centribaric® centrifuge. Keywords: dewatering, hyperbaric centrifuge, pressure drop, Darcy?s law, Centribaric® centrifuge

Sep 1, 2012

By Edward Judd

CANADA'S mining industry is rapidly recovering from the depression through which it passed in 1921. Its total output of $183,029,600 in 1922 was 6.4 per cent. greater than that of 1921, and was exceeded by only three previous years, 1917, 1918, and 1920. Table 1 compares the output of a few of 'the more important items selected from preliminary data published' by the Dominion Bureau of Statistics. TABLE 1.-OUTPUT OF CERTAIN MINERAL PRODUCTS IN CANADA PER CENT. 1921 1922 CHANGE Cobalt, metal and in compounds, lb 252,000 443,800 +76.1; Copper contents of blister, matte, and exported ores, lb 47,620,820 43,321,400 - 9.0 Refined copper, lb 4,286,000 730,000 -83.0 Gold, fine oz 926,329 1,230,985 +32.8 Pig iron, sh. tons 665,676 429,024 -35.5 Lead, sh. tons 33,340 47,085 +41.2 Nickel contents of matte, etc., lb. 19,293,060 17,496,490 - 9.3 Silver, including that in base bullion, gold bullion, etc., fine, oz. 13,543,198 17,611,646 +30.0 Zinc (nearly all refined), sh. tons. 26,545 28,199 + 6.2 Asbestos shipments, sh. tons 92,761 136,657 +47.3 Coal, all grades, sh. tons 15,057,500 15,045,300 Gypsum shipments, sh. tons 386,550 441,160 +14.1 Natural gas, M. cu. ft 14,077,600 14,954,100 + 6.2 Petroleum, bbl : 187,540 178,570 - 4.8 Cement, bbl 5,752,885 6,943,968 +21.0 Brick, structural, all kinds, M. , , 109,009 127,137 +17.0 On the basis of estimated market values, the whole output of 1922 was contributed as follows: Metals, 33.4 per cent.; non-metallic minerals, 45.1 per cent.; structural materials and clay products, 21.5 percent.; this distribution indicates a return of the metal mining. industry nearly to the position of relative importance that it occupied. before 1921, in which year metals contributed only 28.7 per cent. to the total value. of output while non-metallics gave 51.1 per cent. Canadian cobalt originates entirely in the ores of the Cobalt district, which are mainly treated at smelters in southern Ontario, although some quantities of residues have been exported to England and Europe. Exports during 1922 increased even more than production, consisting of about four-fifths . cobalt oxides and salts, and one-fifth of cobalt alloys and other metal combinations.

Jan 8, 1923

By A. E. Ketler

A second generation lighting system was installed in the Greenwich Collieries longwall. This report describes the hardware, installation, maintenance, and final results of the program.

Jan 1, 1978

By A. G. Starliper, H. Kenworthy

A procedure was developed for the separation of lead and sulfur in industrial concentrates of galena by a combination of chlorination and fused - salt electrolysis . Galena could not be satisfactorily electrolyzed in the various media tried ; however , when it was treated with chlorine the resulting lead chloride could be effectively separated electrically into lead and chlorine . An apparatus was designed and constructed to chlorinate galena and to volatilize simultaneously most of the chloridized impurities . By electrolyzing the chlorinated concentrate , a high percentage of lead was recovered . Anodic chlorine was drawn from the cell and was used to chlorinate new feed . In many runs , the recovered metal analyzed from 99.8 to 99.9 percent lead . Lead was also distributed as a chloride in the bath , and a small portion was in the volatile fraction produced during the chlorination step . During a tinuous operation , only 0.1 percent of the total lead was discarded ; 99.9 percent was accounted for in the metal , electrolytic bath , and washed or leached chlorination condensate which was essentially lead chloride . About 95 percent of the sulfur from the galena was recovered as a byproduct of over 90 - percent grade .

Jan 1, 1964

By Peter H. Toepfer

Hydraulically emplaced, classified mill sands long have been used for stope fill. Entrained water drains rapidly from this type of fill through openings between the sand grains. Slimes are removed to facilitate drainage of the water, thereby lowering dangerous hydrostatic pressures in the fill. Use of unclassified mill tailing as practiced at the Dayrock mine is a recent development and represents a fundamentally different approach to the problems of inhibiting the development of hydrostatic pressures within the stope fill. At the. Dayrock mine, mill tailing is used to form a densely packed fill of sand and slime particles relatively impervious to additional water.

Jan 1, 1952

By S. K. Mathur

This report identifies all the possible activities, variables and factors that contribute to the surface subsidence process over room and pillar workings. These factors are responsible for mine instability and collapse that ultimately transforms into surface subsidence. Such a failure mechanism is initiated by the failure of the mine floor bed and or the failure of the pillars or the failure of the roof after second mining, which eventually brings down the roof. The individual responses of the pillar, floor and roof rocks to the mining induced stresses and the complex interaction between these components can't be attributable to any single factor. Also, no attempt has been made to quantify the significance of each of these factors and relate to the ground subsidence due to the lack of field data. The discussion here is centered primarily on the first mining though second mining is mentioned very briefly,

Jan 1, 1982

By Harry E. Holzschuh

The two Agrico Chemical Company self unloading Phosphate Rock barges put into service in 1976 operate at over their design carrying capacity. Each barge now carries 26,000 short ton instead of the planned 25,000 short ton at 32 foot of draft. They are in service between Agrico's Tampa, Florida Terminal and the Donaldsonville, Louisiana Fertilizer Complex, moving a total of 2,500,000 short tons each year. This was the first use of the Parascrew design for a marine application. The barges, with their 3,000 STPH unloading and matching loading rate is the vital link in this total transportation and handling system. Rock is moved from the Pierce, Florida Mines through the Tampa Big Bend Terminal, across the Gulf of Mexico, and up the Mississippi to the Agrico Faustina Phosphoric Acid Plant 30 miles below Bacon Rouge, Louisiana. The trip from the terminal to the plant is 600 miles and the turnaround time is just about six days. Seven years operating experience has proved that the system works. Fittingly, the two barges are named the "Faustina" and the "Pierce". They have a beam of 85-feet and are 495 feet long. folded depth is 43 feet, with a ballasted light draft of 19 feet and a typical loaded draft of 32 feet. There are four separated holds with the machinery room located forward of 101 hold. Each hold is 51 feet wide at the coamings with an 18 foot straight section on the side, and a 24 foot long, 600 slope sheet for a 23 foot clear reclaim width at the bottom. The Parascrew in each of the holds is 37 feet long between the bearings and is supported on a 14 inch diameter hollow shaft. The screw pitch varies and the diameter of the flights step up from l'-9" diameter to 2'-6" diameter on the discharge end. By sloping the centerline, a minimum four inch bottom clearance is maintained across the hold. Some bending of the tube does take place.

Jan 1, 1983

By Harry Perry

One of the most notable achievements of the iron and steel industry in the United States in this century has been the general increase in productivity of individual blast furnaces and the reduction in coke rate. Most of the improvement in furnace operations has occurred within the past decade. During this time the output of the average furnace increased about one-third, while fuel rates decreased from 15 to 20 percent. For example, in 1949, the iron and steel industry produced 811.2 short tons of pig iron per blast-furnace day with a coke rate of 1,870.4 pounds per ton of pig iron, By 1960, the average production of pig iron per blast-furnace day had risen to 1,182.4 tons, while the coke rate had decreased to 1,497 pounds per ton of pig iron. These figures are averages for the entire industry; many furnaces produced over 2,000 tons per day and one furnace, operating on pellets, reached 2,700 tons of pig iron per day, Coke rates of individual furnaces varied, but some furnaces operated on less than 1,200 pounds per ton of pig iron. The significance of this decrease in coke rate is shown clearly when data on pig-iron production and coke consumption in 1959 are compared with 1948. In 1948, 57.3 million short tons of coke was charged into blast furnaces to produce 60.1 million tons of pig iron; in 1959 only 47.6 million tons of coke was needed to produce 60.2 million tons of pig iron. Thus, in 1959, nearly 10 million tons less coke was required to produce about the same amount of pig iron as was produced in 1948.

Jan 1, 1962

By M. P. Sinha, Rashmi, Tata Steel Ltd., S. Jaiswal, A. Bhatnagar, P. Garg

Reagents form a crucial part of flotation process as they have the power to control the surface properties of minerals. In case of coal flotation, collectors and frothers are two the important and commonly used reagents. But other types of reagents such as promoters, modifiers and depressants are also finding wide applications because of their availability to improve selectivity and increase recovery. Because of these chemicals the scenario has changed from flotation being used mostly for high rank hydrophobic coals to low rank, oxidised or inferior coals. In the present work a case is presented in which two non-ionic surfactants (abbreviated as A & B) known to act as emulsifier have been studied to get a better flotation performance for a preparation plant with varying feed characteristics. Laboratory flotation tests were conducted with both the surfactants using three feed samples of the plant by varying the dosage at three different levels. The highest combustible matter recovery (more than 80%) was obtained for surfactant B at a dosage of 75 ppm (parts per million) for feed 1. But at the same dosage the recovery decreased by 21% and 10.2 % respectively for feed 2 and 3. On the other hand surfactant A showed a consistent result for all the three feed samples giving the highest value at a dosage of 50 ppm followed by a decrease beyond this point. The tests were complemented by contact angle measurements that demonstrated the same trend. In addition to this the reproducibility of data for Surfactant A was checked and found that the standard deviations for both separation efficiency and combustible matter recovery were within the permissible range (less than 5%). Finally an in-plant process optimization study to evaluate the performance and applicability of surfactant A at industrial level was done and has been discussed.

Jan 1, 2016

By L. J. Vincze

The program of study of pellet binder materials was begun by the ORF in 1963 to examine various Canadian materials as substitutes for bentonite which is imported in large tonnages (199,270 tons in 1969) from the U.S.A. for Canadian pellet plant operations. Most of the raw bentonite used in Canada originates in Wyoming, North Dakota and more recently Greece, resulting in relatively high transportation costs to pellet producers. Some Canadian bentonites available in Western Canada (Alberta) can be beneficiated for uses as pellet binders but could not compete in cost with U.S. sources due to the cost of beneficiation and the higher rail transport charges to Eastern Canada. It is difficult to find a substitute for bentonite, and many materials have been investigated by research groups but, so far, no economic substitute is in use. However, some success is apparent in studies of low cost materials such as clays, sea weed, peat moss and low grade coal, The work done by the ORF over several years has covered systematic test¬ing of Ontario clays, lignite, some types of tree bark, waste sulphite liquors of various kinds, and peat moss as binders for iron ore pellets. The major effort has been concentrated on peat moss and has included a study of the influence of different additives. Since analysis of peat moss for humic acid is difficult and time consuming, a certain amount of time was devoted to development of improved methods, the most useful of which was a spectrophotometric method based on extraction of peat by sodium pyrophosphate for determination of humic substances. In the present paper, only the most recent work concerning the use of peat moss with suitable additives is discussed in detail, since it is the most conclusive and best documented portion of the program.

Jan 1, 1971

By H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Mesozoic iron oxide-copper-gold (IOCG) mineralisation in southern Perú and the northern Chile coastal IOCG belt have emerged as two of the major exploration targets in the Central Andes in the last two decades. These Mesozoic Andean IOCG deposits formed in two mineralisation epochs, the Middle-Late Jurassic (170–150 Ma) and Early Cretaceous (130–110 Ma), with the major Cu-rich IOCG deposits located in the Early Cretaceous mineralisation belt. The early studies in some IOCG centres support a magmtic-hydrothermal model for both Cu-rich IOCG deposits and broadly contemporaneous Cu-poor ‘Kiruna-type’ magnetite deposits. However, recent evidence from field, geochronology, fluid inclusions and stable isotopes show that in the major Central Andean deposits (eg Raúl-Condestable, Mina Justa in southern Perú, La Candelaria-Punta del Cobre and Mantoverde in northern Chile), the incursion of evaporite-sourced basinal brines or sea water may be a prerequisite for economic Cu mineralisation. Moreover, the Cu-poor massive magnetite deposits could be interpreted as a product from iron oxide melt, with minimal intervention by non-magmatic fluids. Therefore, they could represent two contrasted deposit types and contain little genetic relationships. The different roles of magmatism during the Mesozoic are responsible for the variable mineralisation in the Central Andes, including IOCG, magnetite and ‘manto-type’ deposits. The ore modelling for both the Middle-Late Jurassic and Early Cretaceous metallogenic epochs in the Central Andes are reconstructed.CITATION:Chen, H, 2015. The Mesozoic iron oxide-copper-gold (IOCG) mineralisation in the Central Andes – a refined IOCG ore-forming model in the Palaeozoic Continental Margin, in Proceedings PACRIM 2015 Congress, pp 251–254 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By John L. Schaller

The Bureau of Mines, U.S. Department of the Interior, has investigated the extraction of alumina from domestic kaolin clay by leaching with boiling 26 wt-pct hydrochloric acid. Acid leaching of crushed calcined kaolin feed yields slurries that are slow settling and difficult to filter because of the presence of fine particles generated in crushing, calcining, and leaching. Laboratory research showed that tumbling and moistening crushed raw kaolin on a pelletizing disk caused the fines to agglomerate on the surfaces of the larger particles, while the sharp edges and corners of the larger particles were rounded off. Minus 16-mesh crushed raw kaolin was misted on a 36-in-diam, 8-in-deep pelletizing disk at rates of 175 to 250 lb/hr, and was calcined in either a rotary or a fluidized-bed calciner; negligible degradation occurred. The physical properties of the misted calcined kaolin were evaluated in the leaching system of the clay-hydrochloric acid miniplant. Only minor attrition occurred during leaching, and the slurry was readily filtered on a continuous belt filter.

Jan 1, 1982

By William A. Hustrulid

An overall summary and the individual reports of eight workshops to determine research and development needs in western mining ore presented. Problem areas are identified, and recommendations regarding priorities, funding sources, and prime movers are made. The objective of this contract was to identify research and development needs for advancing mining technology as well as health and safety measures for western U.S. Surface and underground mining. This was accomplished by convening a series of workshops where problems could be thrashed out by producers of trona, uranium, open pit copper, underground salt (from the Midwest and New York), underground metal and nonmetal, etc. In addition to problems, future priorities, funding, and the desicion as to who should be the prime mover on R & D were discussed.

Jan 1, 1976