Search Documents

By R. Newman

An inexpensive slow-speed data acquisition system has been adapted to digitally record multiple parameters simultaneously at intervals of 15 seconds. The system was built for use with standard soils testing equipment to automatically record load and displacement parameters at predetermined instants in time. Simultaneous readout is achieved by the use of special signal conditioner and sample-and-hold circuits which read the multiple signals simultaneously and hold them until the slow acting system can print out. Three channels of a 10-channel system have been converted and found to operate successfully during a series of direct shear tests. A unique feature of the system, which significantly reduced its cost, is the power supply units. Dummy circuits are used to maintain a constant power demand during sampling) thus eliminating the need for a costly power supply with rapid response characteristics. The entire system, having an overall accuracy of 0.25 percent, was put in operation for a cost under $2,500.

Jan 1, 1970

By Cristiano Devitte

O presente trabalho busca verificar a viabilidade técnica de utilização de aços com diferentes percentuais de elementos de liga em sua composição química para a fabricação de brocas DIN 338, com e sem revestimento PVD de TiN comparando com aço AISI M2. A caracterização do material foi realizada em conformidade com a norma SEP 1615 e a identificação do tamanho de grão foi realizada pelo método Snyder-Graff. No teste de furação foi utilizada um centro de usinagem vertical 3 eixos. A aderência do filme PVD foi verificada pelo teste de indentação VDI 3198. As variáveis significativas foram o material do substrato, o revestimento da ferramenta, a velocidade de corte e o avanço de corte. As variáveis de resposta analisadas foram o desgaste da ferramenta, o número de furos produzidos, a rugosidade superficial e o diâmetro dos furos. Ao final do trabalho foi possível constatar que o material Z2 ainda não pode ser utilizado como alternativa ao AISI M2 para a fabricação de brocas helicoidais de aço rápido.

Aug 7, 2018

By C. Rutledge

The new mining method of multiple strata blasting, called StratablastTM, is described in a separate paper presented at this conference. The current paper presents three case studies where the technique was implemented in three different configurations in large-scale blasts in Australia. The first two blasts were in the Hunter Valley of NSW while the third was at Ensham Mine in Central Queensland. All blasts comprised multiple layers that were blasted in a single drill and blast cycle, with unique designs applied to each layer to achieve different blast outcomes from the various layers.

Jan 1, 2006

By B. A. Wilcox, A. H. Clauer

DURING the course of an investigation on the high-temperature creep behavior of TD Nickel* (Ni + 2) vol pct ThO2), it was observed that the creep fractures were similar in appearance to low-temperature ductile fibrous fractures and creep ruptures by cavitation. Microfractographs of fibrous ruptures are typically characterized by a dimpled appearance, with second-phase particles frequently found near the bottom of the dimples.'-4 These somewhat resemble creep ruptures by cavitation, in that fracture occurs by void formation, with the subsequent growth and final merging of the voids to form a complete fracture.' It is the purpose of this communication to describe the creep fracture of TD nickel and suggest a mechanism for the rupturing process. The discussion is relevant to material crept to fracture in vacuo at a constant stress of 18,000 psi, over the temperature range 900" to ll00°C. The material used in this investigation was 1/2-in.-diam bar stock supplied by Du Pont, contain- ing 2.3 vol pct Tho2. The final fabrication treatment consisted of -95 pct reduction by swaging followed by a 1-hr anneal at 1000°C. Transmission and replica electron microscopy revealed that the material had a fibered structure with a transverse grain size of -1 µ and a longitudinal grain size of 10 to 15 µ. Selected-area diffraction indicated that the fiber axis was parallel to (00l), in agreement with the results of Inman et a1.6 The thoria particle size varied from 80 to 1000Å, with an average size of 400Å, and the mean particle spacing was about 1200Å. The remarkable structural stability7 was confirmed by annealing for 6 hr at 1300°C (about ' 0.9 the absolute melting point). Transmission electron microscopy revealed that the only structural change was a slight decrease in dislocation density. Furthermore, recrystallization or grain growth during creep has not been observed. All specimens were annealed in vacuo at 1300°C for 3 hr prior to creep testing. The following times to rupture were obtained for vacuum creep tests at a constant stress of 18,000 psi: 900°C, 854 hr; 930°C,

Jan 1, 1965

By Steven W. Schmauch

The Sugarloaf RARE II area (No. 5296) covers 11,100 acres in the northern part of the White Mountain Range, in the Inyo fictional Forrest. It is in Nevada, about 45 mi north of Bishop, California. A mineral survey was conducted by On U.S. burro of Mines in 1982 and by the U.S. Geological Survey in 1980-1982. The Bureau reviewed pertinent literature, searched Esmeralda and Mineral County mining records, obtained current claim information from the administrative agencies, and contacted claim owners. Thirty-six properties were examined, and 674 samples were taken from them to help assess win oral resources and potential. The Geological Survey evaluated the regional mineral potential by geologic, geochemical, and Geophysical surveys.

Jan 1, 1983

By J. B. Keast

Introduction The last two or three decades have been marked by striking developments in methods of mining and tunnelling. In view .of increased competition and various economic factors, intensive ' mining has been largely practised, and no effort seems to have been spared to increase outputs and lower the cost of production. In metalliferous mining, the compressed-air rock-drill has effected marked savings in this direction, while in coal mining, the coal-cutting machine has revolutionized mining methods and materially contributed to economical working. Yet, for many years, little or no advance was made in methods of handling the rock, or coal, once it had been successfully broken. Loading by hand is, undoubtedly, the most laborious occupation in the whole of mining operations, and it is also the greatest single item that enters into the cost of production. In view of this, the lag of improved handling methods behind the process of winning the rock or coal is rather surprising. The point, however, was appreciated by mining men, and the introduction of various forms of conveyors and loaders is the result. The belt conveyor, the chain conveyor, the shaker conveyor, and the mechanical shovel entered various parts of the field, but it was left to scraping to provide a method of both conveying and loading. From the pure loading point of view, the choice lies between mechanical shovels and scraper loaders. While it is realised that each of these machines has applications peculiar to itself, yet it should be realised that much work which has hitherto been done by mechanical shovels can be done equally effectively with scraper loaders and at a considerable saving both from the point of view of initial outlay and upkeep.

Jan 1, 1933

By Susumu Uchiyama

This machine was manufactured for excavation of the Roppongi station of the Tokyo Metro Line 12. This machine can excavate both the platform and the rail track at the same time in locations where the traffic is congested and has following features: A multi-centered TBM of the size of 7.06(H) x 13.18(W) m The world first H&V TBM, with right and left machine parts articulated vertically and separately for position control A large erector for simultaneous erection of column and central segments of special shape to construct a highly reliable tunnel This paper reports the design concept, construction, and work record.

Jan 1, 1999

By Thomas A. Giordano

Portable communications equipment is becoming increasingly important in underground mining. Proper selection of microphones and hearing devices to be part of these communication systems is essential if the messages are to be transmitted intelligibly. In this program a thorough study of the requirements for these transducers was made with respect to intelligibility, mechanical configuration, human factors and safety. A computer analysis was made to predict how several combinations of transducers would perform at typical mining noise levels. A survey has been made of those microphones and hearing devices on the market today that might be applicable to the miner communication system. Several systems are proposed and evaluated.

Jan 1, 1976

By A. S. Odeh

During the last few years, several authors1-6 have advanced mathematical solutions, both exact and approximate, to the pressure behavior of a well producing from a region bounded by a circular discontinuity. The most recent solutions were reported by Carter, and by Bixel and van Poollen. Varter solved the appropriate equations analytically. Bixel and van Poollen reported a numerical solution and provided correlation charts for the interpretation of flow tests; their method uses an overlay technique and is valid for wide ranges of mobility and storage capacity ratios. The mobility ratio is defined as the ratio between k/p of the two zones, and the capacity ratio is defined as the ratio between $c of the two zones. We have developed independently an analytic solution, programmed for the CDC 1604, that agreed with Carter's.'1 The same differential equation, assumptions, boundary, and initial conditions were used. We ran 30 drawdowns and 30 buildups of a unit capacity ratio and of varied mobility ratios. We also varied the radial distances to the discontinuity, and the radii of drainage. We examined the results and obtained correlations that were simple to apply and useful in flow test interpretation. The results and the correlations reported here in graphical form allow the determination of the mobility of the two zones and the radial distance to the discontinuity. They eliminate the need to fit field data to a curve as is required in the overlay technique.6 Thus, the advantages of the present correlations are that they require less effort and they provide a unique answer. They also provide guidelines for selecting the parts of the flow test plot to be used in the interpretations. Moreover, the results obtained from the programmed analytic solution define the time intervals where the approximate solution reported by Hurstl and discussed by Larkin2 are applicable. Normal buildup and drawdown plots resulted in an early straight line, a long transition zone and a late (second) straight line. However, the second straight line will not occur if the drainage radius is not at least 10 times the radial distance to the discontinuity. The mobility of the imer and outer zones can be calculated from the slopes of the first and second straight lines, respectively, by the normal methods of the flow test analysis. We found that the radial distance to the discontinuity may be determined from the abscissa value for the point of intersection of the extensions of the two straight lines. Results similar to some of these were reported by Adams et aL7 The approximate solution compared favorably with the exact one during the first and second straight-line periods. However, during the transition zone, deviation occurred between the two solutions. Discussion of Figures Figs. 1 through 7 summarize the results of this investigation. On Figs. 3 through 7 there appears the equation of each respective plot. In this paper the mobility ratio M is defined as klp2/kzpl, where subscripts 1 and 2 refer respectively to the inner and outer zones, and dimensionless time = t, = 6.32 X In the investigation, M ranged from 0.25 to 50;

Jan 1, 1970

Goldfields (Tasmania) Limited operates a small, high-grade underground gold mine on the West Coast of Tasmania, 30 kilometres north of Queenstown. The main orebody, Zone 96, was discovered in 1989, with major development work commencing in 1993. The mine was officially opened in July, 1996. Initial production came from a shallow orebody known as the Sill Zone, some 50 - 150 m below surface, which was accessed by a 1 in 8 decline. Zone 96 lies between 350 m and 550 m below the surface and is accessed by a 402 m deep, 3.2 m diameter internal shaft from the collar level located 100 m below surface. The main ore extraction system in Zone 96 is mechanised cut and fill, using high density paste fill. Run of mine ore and waste are hoisted in a single 5.5 tonne overturning skip, then trucked from the underground collar to the gold plant ROM pad or waste dump, respectively. Ground conditions in the mine vary with orientation and proximity to major faults. The gold is contained in a sequence of strongly altered volcanic rocks adjacent to the Henty Fault. Most of the gold is contained in massive quartz, ranging in width from 0.5 m to 7 m, which has been subjected to substantial faulting. Average mineable grade is about 27 grams gold per tonne. Ore reserves in 1996 proved an initial mine life of approximately 4.5 years at 90 000 ounces gold per annum, with significant potential for additional resources from extensions to Zone 96 and adjacent zones. The lease is located in an environmentally sensitive area and a very high standard of environmental management is an essential part of the operation. This paper describes the relevant aspects of mining at Henty including grade control, ground support, backfill placement and environmental management.

Jan 1, 1998

By S. A. Hovanessian

The method of characteristics which reduces the Buckley-Leverett mnlineur, partial differential equation to two first-order, linear differential equations is applied to the solution of a waterffood recovery problem for multiple lines of producing wells and one line of injection wells. The application of the method is described by a numerical example, and a brief theoretical background is given. From the results of this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple sets of producing wells. INTRODUCTION In this paper, the method of characteristics is applied to the solution of a waterflood recovery problem with multiple lines of producing wells and one line of injection wells. The application of the method to this type of recovery problem considerably simplifies the procedure of obtaining a numerical solution. It differs from the method described by Kern1 because it eliminates the need for integration in obtaining saturation fronts. In addition, the saturation history at any location within the field is obtained from a single diagram (time vs distance with saturation as a parameter)'. The paper includes a brief theory of the method of characteristics and its application to the solution of oil recovery problems. A numerical example is worked out, and the cumulative oil recovery-vs-time curve for a system with multiple sets of producing wells is obtained. This curve is then compared with the recovery curve of a system with only one set of producing wells. From this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple lines of producing wells. However, the recovery time is considerably longer for multiple sets of producing wells.

By Clayton M. Rumsey

No producing or developing mines nor known mineral resources are in the Lower Saline Valley Wilderness Study Area. The inactive Bonanza Prospect has low potential for copper-gold-silver resources. Stone and sand and gravel deposits in the WSA do not constitute mineral resources because transportation costs to major markets are prohibitive. INTRODUCTION The Lower Saline Valley Wilderness Study Area (WSA) covers 2,241 acres in southeast California adjacent to and west of Death Valley National Monument (fig. 1). Access to the WSA is by the Saline Valley gravel road 28 mi northerly from its junction with State Highway 190. The junction is about 35 mi southeast of Lone Pine, CA. The WSA is characterized by moderate to steep, sparsely-vegetated slopes; elevation ranges from about 1,800 ft to 3,560 ft.

Jan 1, 1984

By Han Yi

The coarse indium ingots produced by Shaoguan smelter contained a lot of impurities. In order to produce the high pure indium with the purity more than 99.99%, the appropriate refining processes were designed and the practice of combined application of Glycerin-KI process and electrolysis in Shaoguan smelter was introduced.

Jan 1, 2005

By Othon do Rêgo Monteiro Neto

[The present study has investigated the extraction of copper from a chalcopyrite flotation concentrate using an adapted strain of Thiobacillus ferrooxidans and shake flasks, tank leaching and Warburg respirometer techniques. From the shake flask experiments, the activation energy and the frequency factor have been determined to be ?ka = 59.4 kJ and A = 3.3 x 105 S-1, respectively. The temperature coefficient was found to be Q10 = 2.2 in the range of 20 to 35°C. It was suggested that the reaction mechanism of chalcopyrite leaching by T. ferrooxidans involves the formation of an activated complex. whose thermodynamic values have been calculated to be ?G? = 92.1 kJ, ?S? -148.8 J K-1 and ?H$ = 47.8 kJ. The maximum volumetric oxygen mass transfer coefficient for the reactor leaching was found to be achieved by using an optimum air flow rate of 1970 cm min l at a rotational frequency of 1000 min-1. The highest copper extraction in tank (reactor) leaching experiment was 86.8% after 17 days of leaching, while in the sterile runs the corresponding copper extraction was only 40.1%. The copper extraction was suggested to be diffusion controlled. The power requirement of the aerated reactor was calculated to be Pg = 2.02 watts. During leaching, the oxygen saturation concentration was found to be C* = 6.70 mg dm-3. Using the gassing out method the critical oxygen concentration was assessed to be CCrit 0.05 mg dm 3. From the Warburg experiments, the kinetic parameters of the Monad equation were derived with a new evaluation technique to be Vmsp = 9.0 µm3 02 min-1 mg protein-1 and K = 7.4% pulp density for the effect of substrate concentration. The order of reaction and the overall reaction rate constant were determined from the modified van't Hoff plot to be n = 0.0 and k = 1.49 p dm3 02 min-1 mg Protein -1 for the chalcopyrite concentrate oxidation by T. ferrooxidans. On the basis of this experimental work, a preliminary flow sheet has been proposed for the bioextraction of copper from flotation concentrates.]

Jan 1, 1985

By Olman Hee

This study investigates the identity and relative importance of factors affecting the future demand for phosphate rock, potash, and nitrogen. The main objective is to analyze demand relationships for these chemical raw materials for some specified past period, and to utilize this information to make projections of consumption into some designated future period. The end-use approach is used, which divides total consumption of each chemical raw material into agricultural, industrial, and export use. Multiple regression analysis is employed to statistically measure the relative effects of the different factors on consumption in each end use. The general method centers on the construction of a consumer demand model, the fitting of the respective equations in the model, and the interpretation of the statistical results. Direct and cross price elasticities of demand are computed for each end use of the chemical raw materials. These give an insight into expected changes in consumption with respect to given changes in price. The results of this study indicate that price, consumer income, and level of technology are factors which measurably affect consumption of chemical raw materials. For phosphate rock and potash, the agricultural and industrial end uses showed an inelastic demand, whereas for nitrogen, all end uses (including export use) exhibited an elastic demand. Among the chemical raw materials, average annual growth of consumption of nitrogen for agricultural and export uses to 1980 is expected to be notably higher than that for phosphate rock and potash.

Jan 1, 1969

By E. H. Izen

A thermal imaging borehole probe was designed and fabricated for the purpose of obtaining thermal images, through smoke, of objects and people in underground mines. The effort was basically unsuccessful; electrical noise, and possibly thermal noise, interferred with the desired signals to the extent that spatial resolution in the images was unacceptable.

Jan 1, 1980

By Robert E. Hershey

1. Estimates of reserves were made for three coal beds in Hamilton County the - Lantana, Sewanee, and Richland. Nine coal beds have been mined at one time or another in the county, but not enough information was available to estimate reserves in any beds other than the three given. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 53 million tons as of January 1, 1954. Of this total 35 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were insufficient for making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove re-serves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By S. Caron

From the early 70?s, ?Centre de Recherche Minérale? (CRM) has conducted and co-ordinated Research and Development activities for the mineralurgical and metallurgical industries. Since 1999, CRM has continued its mandate through COREM which is a consortium of 13 members that uses the benefits and advantages of collaborative pre-competitive industry / university research. In particular, COREM?s ?In-Situ Optimization Group? is involved in the implementation of modern optimization and control tools. The POP Project was launched in order to increase and consolidate the use of modern optimization and control tools and methods for mineralurgical and metallurgical processes. To ensure a successful transfer in the industry, there are a number of essential activities that have to be undertaken. These activities have been identified by COREM?s members and are grouped into three main modules: - R&D Module: Research and Development in universities, research centres and other partners; - Technology Transfer Module: integration of new tools and methods into the POP Software, industrial applications and technical support; - Training Module: education of new engineers in universities, continuing education of plant personnel through on-site workshops and resource networking by specific information exchange tools. This paper outlines the opportunities that led to the definition of the POP Project and describes its main modules. The main features of the POP Software are presented, the first application is described and finally, future developments are discussed.

May 1, 2001

By Jules Gordon

Presents the results of mining tests conducted on a forward rotating bucket wheel excavator designed to continuously mine coal at 1080 tons/hour, Goals of the program are to determine the feasibility of the forward rotating bucket wheel principle as an effective means of reducing fragmentation and loading costs associated with surface mining, with additional benefit in reducing, coal preparation costs and stripping overburden. Tests took place at the Navajo Mine in Fruitland, New Mexico, Results show that the excavator performed as expected and can reduce fragmenting and loading costs up to 80°. Presented are: 1) production machine design specifications and projected economies extrapolated from the test data, and 2) recommendations for further work in dust control.

Jan 1, 1977

By V I. McCallum

In 1954, Falconbridge Nickel Mines Limited began the program of deepening the Falconbridge mine workings for 2,000 feet below the bottom, or 4025, level in order to provide twelve new levels for production. Involved in this program were a production-sized internal shaft, .crushing, pumping and hoisting installations, the integration of the new shaft operations with those of existing shafts, and considerations of ventilation requirements and ground support at depth. This paper describes the major items of equipment, and the depth development of No. 9 shaft as a whole, and also emphasize the planning phases of the program. The factors involved and reasons for the equipment and layouts chosen are given. Introduction and History THIS paper describes the planning and development of that portion of the Falconbridge mine between the 4025 and 6050 mining levels. This mine, the oldest of several being operated by Falcon-bridge Nickel Mines Limited in the Sudbury district, has been a continuous producer for over thirty years.

Jan 1, 1964