Search Documents

This paper pays tribute to the pioneers in geomechanics, and addresses some of the most pressing issues of our time related to deep mining, and how to mitigate these issues. Solutions developed by our predecessors seem to have reached their limits as mines continue to go deeper. The International Society for Rock Mechanics (ISRM) guidelines for rock mass characterization for excavation design also require re-thinking to reflect current knowledge and experience. Thus, a whole new approach is urgently required to increase mine safety and productivity. The paper will draw on the challenges and experiences in medicine and science that have been overcome through genuine collaboration, advances in technology, and impressive funding, which can be adopted to provide solutions to contemporary geomechanics challenges for increased safety and productivity as mines continue to go deeper.

Jan 1, 2014

By M. Zanotto

[ ] A period of heavy rains caused the river Adda to flood parts of the Valtellina, one of the Alpine valleys of Northern Italy. The exceptionally high waters put under considerable strain the whole system of embankments and levees controlling the river and protecting the adjacent towns and lands. In some places the water breached and washed away the embankments, submerging large tracts of cultivated land, buildings, roads and railway tracks. The town of Talamona, in the lower Valtellina, was hit particularly hard: in its proximity the river overrun and then washed away 300 m (1,000 ft) of embankment (see vicinity map, fig. 2), depositing large amounts of riverbed debris onto over 400 hectares (1,000 acres) of fertile land.

Jan 1, 1992

By Hermann Wotruba, Lars Weitkämper

"Dry coal dressing was popular during the 1950’s and 60’s in many parts of the world. The devices mainly used were air jigs and air tables.The increase in ash and moisture content of run-of-mine coals due to the wide advanced mechanisation of mining methods during and after this period led to that pneumatic devices being unable to treat run-of mine coals with the desired efficiency. Since the 1960’s almost all new coal preparation plants have been based on wet processes that are highly efficient in terms of coal recovery and their ability to handle damp and sticky run-of-mine coals. (Frankland, 1995)However, water is becoming increasingly costly and the disposal of fine products, containing most of the water, is an environmental concern. There would be significant cost savings and a lower total energy consumption if coal could be cleaned dry. Efficient dry coal treatment would be an interesting solution in desert, arid or cold areas.In Germany one dry coal dressing plant is in operation. This is the last operating dry coal dressing plant existing in Europe. The actual technical standard of dry coal dressing has been analysed during test-work and sampling in this plant (Saar Region in Germany). The process and the advantages and disadvantages are presented. The plants problems are low efficiency in the fine fraction –6 mm and the coarse fraction +30 mm and a low overall throughput as well as the lack of an automatic process control system. The separation results in the medium size fractions between +6 and -30 mm are excellent"

Jan 1, 2003

Some crystal chemical properties of several apatites from Brazilian deposits and occurrences were determined; the samples had different origins (igneous, metamorphic and sedimentary). The aim was to establish relationships to their froth flotabilities behaviour. Detailed X-ray diffraction studies were carried out, to determine precisely the unit cell parameters and the degrees of crystallinity of the apatite samples. A thorough chemical analysis of these minerals was also conducted. Microflotation studies were carried out, using sodium oleate and dodecylammonium chloride as collectors. The crystallinity levels were determined for all samples studied, with the establishment of a crystallinity index, which varied from 10.0 to 4.5, on a normalised scale. A marked dependence was observed between this crystallinity sequence and flotability; for both collectors, flotability dropped drastically for crystallinity indices lower than 8.0. Also, the low crystallinity apatites showed a decrease in floatability, for longer conditioning times.

Jan 1, 1993

By Gi-Chun Han, Ki-Suk Han, Korea Energy Management Corp., Jin-Sang Cho, Hyung-Seok Kim, Jae-Hyun Oh

This study has been carried out to use the waste sludges generated at Pohang Iron & Steel Co. Ltd. (POSCO) as the raw materials of Ordinary Portland Cement (OPC). The burnability index of the raw mixture and the hydration characteristics and compressive strength of clinker have been examined. The waste sludges were mainly composed of CaO, SiO2, Al2O3, and Fe2O3, the main component of OPC. The Burnability index of mixture was improved, according to the replacement content of POSCO sludge increase. POSCO sludge can be used as a raw material for cement because the state of mineral development and property of clinker produced from POSCO sludge are similar to the plain. Therefore, POSCO sludges can be used as the source materials of iron and calcium oxide.

Jan 1, 2003

The effect of composition on electrical conductivity (resistivity), viscosity and liquidus temperature of the slags encountered in electric smelting of PGM containing suphide concentrates is reviewed, along with the relationsip between slag composition, slag-matte separation and metal losses to slag. Optimization of slag composition at furnace temperature is attempted on the basis of opposite and parabolic trends of the viscosity-conductivity relationships of the slags. The importance of surface tension of slags is emphasized using available and estimated information which are grouped into a useful correlation. These values are coupled with or incorporated into slag viscosity plots to illustrate the correlation between the two factors, which influence slag-matte separation as well as refractory attack. The electrode in the slag-resistance furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power. The obvious parameters are the size and positioning in the slag bath, which are defined by slag resistively, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles, which in turn affect flow conditions. Thus the flow of slag and matte are discussed in conjunction with the furnace geometry, stirring action of the electrodes, buoyancy and electromagnetic effects. The action of the electric furnace as a settler is discussed. The rectangular furnace is considered as a channel reactor in this analysis, and the action of the electrodes is described to indicate a balanced settling rate in the area of electrode action. Discussion of the design and production capacity of the electric furnace, with reference too perating current, power input, furnace dimensions and electrode size, are based on considerations derived mainly from slag properties such as its resistively, viscosity and liquidus temperature.

Jan 1, 2004

By Frank D. McGuirk

Underground coal mining is traditionally hazardous. Although many danger-prone human activities are now performed by mechanized equipment, this mechanization has itself brought new dangers to the underground mining industry, and the loss of life and limb has caused increased concern for mine safety. The 1969 Federal Coal Mine Health and Safety Act has precipitated a great deal of safety-related research on the part of the Government, industry, and private agencies. Much of this safety research has been focused on the new and varied man-machine interfaces caused by increased mechanization. Recent projects in this area have dealt with standardized controls, emergency shutdown capabilities (panic bars, strike plates, self-centering controls, "dead man" controls), and machine operator protective devices (fully enclosed cabs, canopies, side rails). There was a need for integration of the findings of current and past projects to move rapidly toward the smooth, orderly implementation of standardized operator work station designs for underground mining equipment.

Jan 1, 1975

By Mostafa Benzaazoua, Bruno Bussière, Philippe Poirier, Denis Bois

"Environmental desulphurisation is an attractive alternative for the management of acid generating tailings. Non selective froth flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works (McLaughlin and Stuparyk, 1994; Bussière et al., 1995; 1998; Benzaazoua et al., 2000a,b; 2002). This process can reduce the volume of problematic tailings to manage, by making a sulphide fraction concentrate. The desulphurized tailings can then be used as a moisture retention layer in a cover with capillary barrier effects to prevent acid mine drainage.In this paper, the authors present the results from different laboratory and pilot scale flotation tests which confirm that low sulphide, non-acid generating tailings can be produced by froth flotation. It is also demonstrated that the sulphide concentrates obtained from desulphurisation, when mixed with binders gave good long term results in terms of mechanical behaviour, thus demonstrating that the sulphide fraction can be used for paste backfill material. From previous work (Bussière et al. 1998, 1999) on the evaluation of the operating and capital costs of the desulphurisation process for different ore types, the use of desulphurized tailings to create a dry cover was then studied for several scenarios. The desulphurisation process was compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation and the advantages and disadvantages of desulphurisation are presented as well as the costs of this method of AD prevention.INTRODUCTIONThe principal environmental problem of the mining industry today is the generation of acidic drainage (AD) resulting from the natural oxidation of the sulphides in mine tailings. This phenomenon involves the generation of acidity which increase the amounts of toxic metals in the waste water released into the environment by a mine. The environmental impact of the AD has been described in detail in previous work (e.g. Down et Stocks, 1977; Ritcey, 1989; Gray, 1997; Ripley et al., 1996; Aubertin et al., 2002)."

Jan 1, 2004

By Takashi Furuyama, Sukeyuki Mori, Abel Bissombolo

"In flotation practice, a good recovery of minerals largely depends on the degree to which the valuable minerals have been liberated from the associated gangue during the grinding process. Therefore, a regular measurement of the degree of liberation can provide data for the assessment of the quality of separation and predicts the effect of changes in the grinding-classifying circuit on flotation process. Generally, the standard procedure for measuring the degree of liberation requires the preparation of polished sections - a time consuming operation that also has the disadvantage of providing an overestimated number of free particles because of the stereological nature of produced samples.The present work is an alternative approach to avoid these miscalculations and establish a system of control for fluorite flotation plants. The system deals no only with the state of liberation but also the dynamic behavior of individuals particles and mineral components within the grinding-classifying and flotation circuits. It involves methods such as sieving, x-ray diffraction analysis, study of polished sections and microscopic counting of preliminarily sieved minerals particles from a fluorite processing plant, randomly dispersed on a glass slide, but not embedded in a resin mounting medium. If a complete information on the textural properties of minerals in the ore (including its mineral components distribution) can be obtained through x-ray diffraction analysis and study of polished sections, the microscopic counting is used to determinate with enough accuracy the mineral liberation, estimate the grade of fluorite ore and products, determinate the deportment and approximate recovery of individuals particles and mineral components within the investigated circuit. For a count of 100-1000 particles in each n-size range, the counting method was found to be a particularly reliable and less time consuming operation that could substitute the chemical analysis of fluorite ore for an estimate of the grade:"

Jan 1, 2003

By P. S. Jacobsen

In 1960 over 93 percent of the coal cleaned mechanically in the United States was cleaned in processes that utilized water or dense-medium suspensions of fine solids in water. Thus, in the process of removing deleterious ash-forming and sulfur-bearing minerals, another deleterious substance--water-- is added to the coal. The subsequent removal of the water from the coal, and the concomitant recovery of the coal from the water, is not troublesome in the sizes coarser than 1/4-inch. In the finer sizes, however, it is a difficult procedure that often costs more than the original washing operation. Because of the importance of liquid-solids separation in coal preparation, the Bureau of Mines has a continuing program of research in this field. The objective is to make available information on the performance characteristics of various types of equipment available for liquid-solids separations, thus promoting the wise selection of equipment for specific applications, and, thereby, more effective processing of coal. Results of work on flocculation as an aid to filtration5 and the sieve bend screen6 have been published. The present investigation of the screw-type classifier operating in combination with the cyclone was undertaken primarily because such classifiers are comparatively new to coal preparation and information on their performance is not available. The cyclone has become well-known since its introduction in this country by the Bureau of Mines in 1948.7 Use of the cyclone in conjunction with the screw-type classifier represents an attempt to provide the maximum recovery of solids at minimum moisture content.

Jan 1, 1962

By R. H. Grau, S. B. Robertson, F. Garcia, A. C. Smith, T. P. Mucho

Researchers working for the National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory are developing ways to protect the health of miners. Part of that effort is devoted to improving the air quality in underground stone mines by developing ventilation techniques that can be used in these types of operations. The air quality in these large opening nonmetal mines can be significantly improved by using diesel particulate matter (DPM) controls along with sufficient ventilation quantities to remove contaminants. Practical methods of ventilating these underground stone mines can be accomplished by using mine layouts that course and separate ventilation air through the use of stoppings. The design, construction, and maintenance of effective stoppings in large openings have been a real challenge to mine operators. Several different types of stoppings have and can be used for this application. The choice of stopping design, material used, and construction techniques should be dependent upon a number of factors such as the intended life and effectiveness desired.

By James A. Finch

"I offer a personal view of what the next 30 years holds for mineral processing. Re-stating that mineral processing will remain a vibrant industry in raw material production, growth opportunities in waste management are identified. The processing sequence familiar now (mining -mineral processing -extraction) will become more interwoven. In situ processing (i.e., milling underground) will evolve from concept to demonstration. Opportunities to exploit physical properties altered in chemical (pyro-and hydro-) processing will present themselves. In primary grinding, the path to AG/SAG milling will progress with little deviation but opportunities in regrinding are wide open. Flotation will see the trend to designing bubble/particle reactors accelerate simultaneously with a vigorous response from mechanical cell suppliers. Gravity separation remains a bastion of the lone inventor but I anticipate that the new lines will come from the waste management business. I finish by examining the ""research cycle"", identifying growth in small ""high tech"" companies and university research centres.IntroductionI have been asked to offer a personal view of""where we are going in mineral processing?"". Gazing into crystal balls is quite a cottage industry as we approach the end of the millennium. Academics are often asked to assume the role of visionary, I presume because it is considered in their mandate, to reflect and philosophize (or, less charitably, because they are considered to have the time). Since this is the 30th Annual Canadian Mineral Processors Operators Conference, I am tempted to suggest the next 30 years as my frame of reference. This is about equivalent to one engineer's career or, given it takes typically 15 years to go from concept to realization in mineral process engineering (Napier-Munn, l 997a), about 2 ""invention cycles"". With this length of cycle, much that is familiar now will remain so over the 30 years.Research and development (R&D) is in response to need. The overarching need in mining is to find new ore bodies. Process developments cannot compensate for a depleting deposit or a declining commodity price. Mineral processing R&D is characterized by incremental gains, aimed at pushing the mine down the cost per tonne league table. Breakthroughs are the exception (flotation at the turn of the century was one). This must be kept in mind when trying to predict the future in our business."

Jan 1, 1998

By A. V. Pavlov, V. A. Grygorian, Kossyrev, A. E. Semin, A. Korostylev

A new way of producing low-silicon ferrosilicon from iron-ore materials in a new type of aggregate-oxygen reactor is presented. The oxygen reactor process is based on using the calorific combustibility and reducibility of carbon materials inside the aggregate. The key to the process is successful post-combustion of carbon monoxide above a layer of a solid coke bed. Initially the possibility of production of grades of ferrosilicon containing 20 to 25% Si (FeSi20-FeSi25) was studied on a laboratory model of the oxygen reactor. Quartz sand and iron ore concentrates (from Russia and India) were used in the laboratory tests. This test work demonstrated that a ferrosilicon grade FeSi15 could be obtained directly from raw iron ore (containing 75.9 % Fe2O3 and a maximum of 23.8 % SiO2) without using rich iron-ore concentrates. The process was successfully tested on a pilot furnace at Serovsky metallurgical plant. Very promising results and efficiency parameters were achieved. The consumption of materials for 1t of ferrosilicon (15 % Si) production was as follows: 1567 kg raw iron ore, 591 kg of coal (in a composition of ore-coal briquettes), 299 kg of coke (for coke bed formation), and 815 m3 of oxygen.

Jan 1, 2004

By D. Mohapatra

Extraction of Al(III) from aqueous sulfuric acid solutions into organic Cyanex 272®-carbon tetrachloride systems was investigated from a multi-component mixture containing aluminum, cobalt and nickel. Al(III) extraction efficiency was quantitative with 1.0 M Cyanex 272® in two stages at an aqueous: organic (A:O) phase ratio of 1:1 and an equilibrium pH of 3.2. The stripping of Al(III) from the loaded organic (LO) with different acids indicated sulfuric acid to be the best stripping agent. More than 99% stripping of Al(III) from the LO was achieved using 2 M H2SO4 at an A:O phase ratio of 1:1 in a single stage. The stoichiometry of the extracted species of Al(III) was determined by the slope analysis method. The extraction reaction proceeded via the cation exchange mechanism and the extracted species was assumed to be AlA3?3HA, where HA refers to the dimeric and A the anionic form of the extractant, Cyanex 272®. The extraction of Al(III) was studied in the presence of various ions to ascertain the tolerance limit of individual ions.

Jan 1, 2008

By K. C. Tran

This paper reviews the advancement of measurement technologies for the control of raw materials processes in the basic industries. The combination of digital technology and on line spectroscopy enables the development of intelligent instruments for composition and particle size analyses in real- time high- frequency control conditions. In many industries, the applications result in productivity improvement and energy savings. Plant specific examples include operating experience and benefits realized in sorting, blending and beneficiation processes. Instruments of the future not only measure specific parameters of the process and monitor its own health combined with self-corrective mechanics but also acts with intelligence to effect the quality of the process or regulate the primary apparatus.

Jan 1, 2001

By S. McAlister

"Falcon Concentrators Inc. has developed a high capacity centrifuge for the recovery of fine, free gold as well as other metals and minerals which were previously thought to be unrecoverable by gravity means. Development started in the early 1980's and the first commercial operation was commissioned in 1986. Gold applications include scavenging conventional gravity and cyanidation circuit tailings, cleaning gravity concentrates, cleaning flotation concentrates to melting grade, scavenging flotation tailings, and placer mining. Recent development work by Falcon has expanded the applications scope of the centrifugal concentrator to include many minerals amenable to gravity concentration including iron, tin, industrial minerals, and hazardous wastes. This paper discusses this technology including its history, present applications, and future potential. OVERVIEW OF CENTRIFIJGAL CONCENTRATIONUsing centrifugal force to enhance the separation of materials by differential specific gravity has been researched for over a century. Many attempts have been made to concentrate minerals in high gravity fields. Patents were granted on this subject as early as 1891 (see Figure 1). Patenting activity continued into the 1920's and has been relatively quiet since. It is significant that no centrifugal system of gravity concentration has been broadly accepted by the mineral processing community until recently. Much of the world's reserve of mineral deposits which are amenable to conventional gravity concentration technology (coarse-grained) have been mined and therefore there is an increasing demand for technology which can economically recover the fine-grained gravity recoverable minerals in the remaining deposits. In addition, centrifugal concentration can play an increasing role in solving environmental problems by offering an inexpensive method of concentrating hazardous materials such as uranium, plutonium, mercury, lead, and other heavy metals. The overall cost of disposing of these substances safely can be drastically reduced if they are recovered into a concentrated form prior to disposal."

Jan 1, 1992

By L. L. Lacerda, A. J. Blair

The Wolf Creek Upper Narrows Tunnel (Upper Narrows Tunnel) is one of the first major highway tunnel in the United States implementing the use of spray-on membrane for purposes of constructing a double-shell drainage solution between an initial shotcrete lining and a final cast-in-place concrete lining (Figure 1). In the case of the Upper Narrows Tunnel the primary membrane is constructed with a spray-on product manufactured by Degussa, namely Masterseal® 340 FA (MS 340) that has been utilized previously in other tunnel projects. Shotcrete-like in application, but differing in physical properties, MS 340 is now outdated, and is succeeded by Masterseal® 345 (MS 345), a nearly identical product, with improvements in material properties. Tunnel project histories utilizing either MS 340 or MS 345 are discussed and summarized with regard to the respective motives for prompting spray-on membrane selection and the realized benefits resulting from spray-on membrane construction. With an emphasis on the Upper Narrows Tunnel, project summaries discuss details of the aspects of design for spray-on membrane construction methodology as opposed to conventional sheet membrane construction methodologies. It is anticipated that experience gained during the construction of the Upper Narrows Tunnel with respect to other tunnel projects that have utilized spray-on membrane will be of use for future tunnels employing spray-on membrane in drainage solutions.

Jan 1, 2005

By Wilfrid Comeau

This paper deals with the concept of a Quality-Assurance Manual, to the ISO-9001 Level, for quarry blasting in the urban environment. A case history of the incident, which led to its development, is presented in addition to three other case histories. These case histories are related to the potential effectiveness of a well thought-out and applied Quality-Assurance Manual in the conclusions. The basic principle, behind the development of a Q-A manual, is to supply a maximum of quality assurance with a minimum of disturbance to the operation of the quarry. This requires that every intervener in the quarry blasting operations, from management to labourer, be made responsible for the quality of their work. This basic goal can be achieved with a minimum of paper work and added bureaucracy. The manual respects the ISO principle that: Q-A Manuals are not recipe books and should allow for continuing technological developments.

Jan 1, 2003

By H. M. Yang

Structural alteration of pyrophyllite during mechanical activation in a planetary mill was investigated by X-ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR) techniques. Mechanochemical effect markedly promotes the decrease in reflection intensities with increasing the grinding time. Prolonged grinding causes the pyrophyllite to become the amorphous structure. It can be indicated that pyrophyllite is very susceptible to alteration by grinding. Crystal size (d006) of pyrophyllite appears to be a limit after 2h grinding. IR spectroscopy analysis shows a little alteration in the bands of pyrophyllite after mechanical activation. The results indicate that the ordered structure of pyrophyllite is destroyed and lattice deformation occurs. Porous silica was then successfully prepared via leaching the mechanically activated pyrophyllite. Pyrophyllite was first ground for 6 h. Ground samples were subsequently leached with 4 M hy-drochloric acid at 80 °C for 2 h to produce porous silica with specific surface area of 188.1 m2/g, total pore volume of 0.18 mL/g and average pore size of 3.9 nm from N2 adsorption analysis. Otherwise, the porous silica obtained from direct leaching of the original pyrophyllite only has a specific surface area of 4.3 m adsorption analysis. 2/g and total pore volume of 0.03 mL/g. It is inferred that grinding is favorable for the formation of microstructure pores. It offers a simple and convenient route for the preparation of porous materials from natural minerals.

Jan 1, 2014

By V A. Tsukerman

Prospects a new energy saving method for an efficient destruction of the sturdy and hard materials (rocks, ores, frozen soils, concrete blocks, etc) û the Electric Pulse Discharge (EPD) method of materials destruction for green processing in mining and processing of mineral raw materials are considered.The EPD-technologies give additional possibilities for solving ecological problems at the expense of increase of integrated approach of utilisation of minerals and industrial wastes. The scientific and technical level of executed development of EPD method is sufficient for organisation of design work to develop substantially new equipment. A number of plants have been developed and tested, including plants for processing raw material with minerals of jewels, plants for selection of mica from rocks, and plants for processing the merging of artificial mica.

Jan 1, 2002