Search Documents

By José Díaz Barrios

El proceso de la explotación minera de la veta Oroya Techo, perteneciente a la mina Casapalca, ha generado un desequilibrio del macizo rocoso, donde la energía que la roca de la caja, piso y techo (volcánicos de la formación Carlos Francisco) no pueden soportar mas allá del límite de su resistencia y deformabilidad natural, es liberada o “compensada” con el estrujamiento plástico de la veta Oroya Techo (estructura carbonatada). En ese sentido, el presente texto describe una manera de cuantificar dicha deformación a través del monitoreo de convergencias, donde se emplea un simple extensómetro de cinta manual y asímediante una análisis estadístico, seleccionar estaciones de convergencia por rangos de mediciones.

Sep 12, 2005

By T. W. Beck

Overexposure to respirable dust remains a widespread health hazard to roof bolter occupations in underground coal mines. Recently implemented mist drilling technology was evaluated for its effectiveness in controlling respirable dust exposures for roof bolting personnel. This work presents the findings from NIOSH field and laboratory studies comparing respirable dust levels on mist drilling roof bolter machines to dust levels measured on machines using a conventional vacuum drilling system. Gravimetric and instantaneous respirable dust samples were collected for multiple drilling cycles. These dust measurements were used to assess the potential dust control capabilities relative to conventional drilling. Controlled laboratory tests found 0.3 mg/m3 more respirable dust with mist drilling than with the conventional vacuum method. A separate field investigation of the two techniques observed higher dust levels around the mist bolting machine.

Jan 1, 2008

By A. Jennings

[ ] In November 2005, Essroc Cement, part of the Italcementi Group, commissioned a long overland conveyor at their Nazareth plant in Pennsylvania. This conveyor, tagged CV-105, was designed to transport 1000 tph of limestone from the quarry to the kiln, and 400 tph of hot clinker (at 300°F) at back from the kiln to a handling facility about halfway back. Conveyor CV-105 is 8969 ft (2733 m) long. It gains 152 ft (46 m) of elevation in the first 1570 ft (480 m), then is mostly flat for the remaining 7400 ft (2250 m) (Figure 1). After the limestone is discharged at the head pulley, hot clinker is loaded onto the return side of the belt. This clinker can be discharged at one of two locations.

Jan 1, 2012

By D Vickers, N C. Fowke

The reduction of geological risk for planning of high production longwall faces is essential. Geological and geophysical techniques applied at Huntly West Mine before 1989 were unable to reduce the geological risk to an acceptable level. The success of a trial long-hole directional drilling programme at Huntly West Mine (Fowke et al, 1989) has encouraged the Coal Corporation of New Zealand to use the technology long-term, for seam definition. Initial drilling in 1989 completed a total of 3543 metres, with the longest borehole length being 369 metres (limited by number of rods available). A major re-interpretation of seam structure resulted from the drilling, which was able to fill in seam details between surface exploration boreholes. The undulating thick seam conditions at the mine require a refinement of drilling strategies used overseas. Long-hole directional drilling also displays potential for inseam gas drainage. Gas flows of the order of 1000 L/min were initially indicated in individual boreholes. Other gas parameters of the seam have been studied by Beamish et al (1991), and highlight the significance of the natural gas resource in the Huntly Coalfield.   The continued development of drilling technology will be of major benefit sustainable development, particularly in policy.

Jan 1, 1991

By David B. George

Kennecott Utah Copper adopted Outokumpu Flash Smelting and Kennecott-Outokumpu Flash Converting in 1995, a process based on granulating high grade copper matte. While nickel mattes and very small quantities of copper matte had been commercially granulated for years, no large scale copper matte granulation system had been built. This paper summarizes the history and benefits of copper matte granulation, the Kennecott design basis, the successful operation for over 10 years and potential problems inherent in some matte granulation approaches.

Jan 1, 2006

By Walker G. S

A study of the crystalline materials on or near the surface of freshly made or "green" superphosphate granules and mature, "set" superphosphate granules was undertaken using X-ray diffraction, X-ray mapping, scanning electron microscopy and electron probe micro analysis techniques. Calcium sulphate (CaSO4), calcium sulphate hemihydrate (CaSO4 1/2H20), and mono calcium phosphate monohydrate (Ca(H2PO4)2H2O), were the only crystalline species present in the "green" superphosphate.In the set superphosphate however, additional compounds were present, namely complex iron and aluminium phosphates Ca(Fe,AI) H(HPO4hF2)2H2O, (Fe)3(H3O)H8 (PO4)6H2O and calcium sulphate dihydrate (CaSO4.2H2O).The complex phosphates tied up the major part of the Fe and Al in the system and were concentrated on or near the surface of the granule. An intimate mixture of CaSO4.2H2O, and CaSO4, along with the above mentioned complex Fe-AI compounds, crystallize close to the surface of the granule and cause the setting of superphosphate that takes place during storage.

Jan 1, 1980

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

Calculations of the temperatures of metal, coke, and gas at any level in the cupola furn~ce can be carried out by means of heat balances, using data obtained from experiments with an 18 in. experimental cupola. The results can, to a certain extent, be verified by means of heat transfer calculations.The curves thus obtained, showing the variation of temperature with height in the cupola, provide a valuable picture of the heat transfer processes in a shaft 'furnace.INTRODUCTIONThe Brown Coal Research Laboratory, of the University of Melbourne, has been engaged in recent years on a programme of iron-melting tests in an experimental cupola furnace.Although the ultimate aim of this work is to develop brown coal char as a cupola fuel, most of the experimental work so far has been with conventional coke. The testing programme was designed to provide information on the effect of variables such as blast rate, metal-coke ratio, and coke size on the overall melting process, e.g. melting rate, temperature of metal tapped, and stack gas composition.However, in many cases data were obtained on conditions inside the furnace by measuring temperatures and gas compositions. The aim of the work described in this paper was to qevelop a method for using this data to obtain information on the processes taking place in the cupola.Very little research has been done on the combustion of fuels in shaft furnaces. Early work on this subject, as well as the initial stages of the Brown Coal Research Laboratory's programme, has been discussed by Evans (1959). The use of probes for obtaining information on conditions in the interior of a shaft furnace was pioneered by Belden (1913)...

Jan 1, 1963

By M Cooper

Since its enactment in 1991, the Resource Management Act (RMA) has generated both praise and criticism. The major criticism is in relation to the costs the Act poses to industry and the time it takes to work through the process. In response to such criticisms the Minister for the Environment has initiated a review of the implementation of the RMA. The Minister's proposals for reform have not yet been released and the discussion that follows is based upon the report by the Minister's Review Group which was released in September.

Jan 1, 1998

By C Moorhead

The classification of Mineral Resource estimates for reporting in accordance with the JORC Code is a statement of the Competent PersonÆs confidence in the estimate and an attempt to convey that confidence to the various users of the resource estimate. In general the classification process is either largely subjective, relying on the Competent PersonÆs experience, or relies on statistical measures derived from the estimation process. These statistical measures may not necessarily relate to the overall confidence in the resource which must also take account of the confidence in the geological inputs to the estimation. Several authors, including Jackson et al (2003) and Dominy, Noppe and Annels (2004), have addressed methods of including consideration of geological data and its reliability into the classification process. Henry and Parker (2005) have discussed a quantitative measure for classification of Measured and Indicated Resources related to mine production parcels. These methods rely on the availability of sufficient information for the application of geostatistics, data evaluation techniques or repeated interpretation of data to provide an indication of confidence. They are suitable for very advanced projects. In 2005, using a modification of the financial audit æcontrol and quality criteriaÆ principles, then widely accepted within Newcrest Mining Limited (Newcrest), the principal author developed a scheme which categorised the classified resources into æcontrolÆ and æqualityÆ (or risk) categories. Control covers all aspects of the data collection, the geological interpretation, the data analysis and the modelling of tonnage and grade; it is also influenced by the documentation of the estimate. The quality criteria are a subjective measure of risk associated with the estimation of the resource and refer to the risk that the tonnage and grade are not realised and the consequences if decisions are made on the basis of these estimates. By evaluating the generally accepted level of risk attributed to these quality ratings by Competent Persons within Newcrest, a graphical representation of the confidence in the resource ounces was prepared for communication of the expected confidence in the resource statement.

Jan 1, 2009

By S. Z. Pethö

Pillar extraction at shallow depths with small pillars that were not originally intended for secondary extraction can provide a huge benefit to the coal mining industry in those areas where a significant percentage of the remaining coal reserves are locked up in small pillars at shallow depths and where opencast mining methods are simply not as cost-effective and practical to implement. A system considering all of the pertinent geotechnical and mining aspects for the safe and efficient pillar extraction of small pillars at shallow depths at Xstrata Coal South Africa (XCSA) has been further developed and implemented as part of an ongoing improvement process addressing all of the relevant legal and associated risk aspects. This work follows on from the previous pillar extraction work carried out at the ATC, Boschmans, and Spitzkop Collieries. The process involved a number of in-house workshops and sessions arranged with all key personnel from Tavistock Colliery, and also included Professor Nielen van der Merwe of the University of the Witwatersrand, a world renowned authority on pillar extraction, towards reviewing and developing the Modified NEVID pillar extraction system employed previously at Boschmans Colliery. The system is currently being employed at Tavistock Colliery with success and no major accidents, with around 655 000 t of coal having been successfully extracted from the pillar extraction panels.

Jan 1, 2012

By Royal Preston Jarvis

minerals of different specific gravities. It is simple in construction, easily operated, capable of treating large quantities in a short time, and highly efficient under various conditions. The question, whether the material to be jigged has first been sized, determines the two principal methods of jigging. Jigging preceded by close sizing, generally known as the Continental or German system, involves a more or less elaborate series of screens or trommels, with attendant cost for installation, operation, and repairs. Jigging without sizing, known as the English system, is, according to Munroe,1 a development of the hand-jigging formerly employed in Cornwall . and introduced by English miners to this country." In its simplest form, the method consists in jigging an ore-mixture previously crushed to some maximum size (although, in some cases, even this preliminary is omitted) oil a relatively coarse sieve, and then jigging again on a filler sieve, the material passing through the first sieve and bedding. While many modifications have been necessary to adapt it for use in mills of large capacity, where hand-work was necessarily, replaced by machines, the principle remains the same; the fact that the English system has been successfully employed, both in this country and abroad, is well known; and arguments have been made for its efficiency and applicability in a wider sphere than it has occupied hitherto. II. REVIEW OF PREVIOUS INVESTIGATIONS. The fact that treating a mixture of minerals under jigging conditions increased the amount of mineral saved, or, as Professor Richards aptly terms it, 1 ?the extra jig-catch," has long been known. To account for this fact a number of theories have been proposed. The work of Rittinger2 in this field has, for many years, been a classic in the literature of ore-dressing. For the purposes of my present paper, however, the work of two American investigators, Prof. H. S. Munroe and Prof. R. H. Richards, is chiefly concerned. Professor Munroe has given the results of an elaborate series of experiments,3 and his deductions, based largely oil theoretical grounds, of this work. After reviewing briefly the two systems of jigging, followed by a discussion of Rittinger's formulas and

Sep 1, 1908

By Christopher Mark

Knowledge of in situ stresses is fundamental to many studies in earth sciences, and coal mine ground control is no exception. During the past 20 years, it has become clear that horizontal stress is a critical factor affecting roof stability in underground coal mines. The theory of plate tectonics and the World Stress Map (WSM) project has been extremely helpful in explaining the sources and the orientations of the horizontal stresses observed underground. Recently, WSM geophysicists studying deep-seated stresses have developed a model of how stress magnitudes vary with depth in the crust. They have devoted relatively little attention to near-surface stresses, however. This paper explores the relationships between deep-seated and shallow in situ stresses in several of the world?s coalfields, using a data base of more than 350 stress measurements from underground coal mines. The analysis indicates that distinct regional trends exist, corresponding roughly to the regional stress fields identified by the WSM. The paper presents equations for estimating stress magnitudes that were developed by treating depth and elastic modulus as independent variables in regression analysis. The magnitude of the horizontal stress increases with depth, at rates that range from 0.8 to 2.0 times the vertical stress, just as the WSM ?critically stressed crust? model predicts. Overall, it seems that the stress regimes encountered in underground coal mines are closely linked to those that exist deep in the earth?s crust.

Jan 1, 2008

By Michael Wieland

The resolving capacity of the thermodynamic work-principal model has been seriously refined over its twelve year history, so a review of the innovations, wrong turns and their rectification is warranted to help future researchers. The work-principal model rests upon the four laws of thermodynamics that drive the universe and relatively few other assumptions: like the removing and imposing of constraints on the quasi-potential to yield trapped minimum key-states that represent the wanted process. The formative research was concerned with the role of ingredient changes, the removal of booster influence and the quench temperature with which to reckon toxic fumes. The transfer of reaction-zone energy as work upon the surrounding rock/water/fixture was not fully rationalized until the notion of reversed-inertial pressure was formulated and determined (for water) with underwater trinitrotoluene (TNT) shots. The rock-water-jelly model incorporated that term into its dynamic pressure formula as a way to represent rock blasts or underwater shots, while the zone of reaction gases remained trapped. The real irreversible thermodynamic process, which yielded the total expansion work, was later complemented with a wholly reversible imaginary process, to form a closed thermodynamic loop, with a remarkable consequence – the determination of the theoretical heave and hence, the undissipated-shock by difference from the total work. With the wholly developed model, it was recently possible to quantify the time retardation of reaction chemistry for non-molecular (mining) explosives, as compared to the rather negligible time-retardation found for the molecular (military) explosives in underwater tests.

Jan 1, 2009

Very few of those occupied in pursuits other than mining have any conception of the extent of boring operations that have been carried out on the gold and coal fields of Victoria, or of the valuable and definite knowledge obtainable by such means. The subject comprises various branches, which it will be necessary to describe in detail. The three main divisions are The Administrative, which includes all financial work and general management. The Professional, dealing with topographical and geological work necessary before any scheme of boring can be laid out, the preparation of plans, the inspection of cores obtained from bore holes, the examination of diamonds, etc. The Mechanical Branch, dealing with the drilling machinery, setting of diamonds, maintenance of stores, etc. In 1877, the Goverpment of Victoria decided to assist in prospecting the mineral resources of the colony by the aid of diamond drill boring, and for that purpose, a vote of £5,000 was passed, with which were purchased three diamond dulls, an American type being adopted.

Jan 1, 1901

By Maurice Bottiau

"Abstract When addressing the performance of deep foundations, many parameters play a role, from adequate soil investigation to performance monitoring and testing. The correct understanding of pile construction, though, remains crucial. After a long period of empirical design and regulations, the last decades have been the ones of theoretical considerations and extensive codes writing. The interaction between technology and design, however, still plays a determinant role. The introduction of hydraulics and the exponential increase in available power on one hand, the miniaturization and the introduction of electronics in control and monitoring systems on the other hand have exerted a major influence on new foundation systems or the evolution and control of existing systems. It appears important to try to take execution related parameters and their control during execution more deeply into account when assessing the final result of the deep foundations and the achieved level of safety and reliability. In this contribution, we will try to analyze how systems, equipment and pile production monitoring and testing can influence the pile performance, and if/how this influence could/should be translated in adapted safety or installation factors. This analysis will run through different categories of piles: driven, augercast and displacement auger piles and bored piles. INTRODUCTIONThe global performance of a deep foundation depends on different aspects (Poulos, 2003):1. Ground investigation2. Design and analysis3. Construction4. Testing5. Performance monitoring6. Remediation and performance enhancementThis paper intends to address the importance of pile construction and the control of it on the final performance of the pile-group of piles. There has been an increasing interest for theoretical analysis over the last 20 years, followed by an increasing impact of regulation and codes. Without denying the importance of the latter, the author wants to point out how installation procedure and project specific parameters can largely influence the reliability of the deep foundation. In this context, detailed and prescriptive standards can miss their objective of intended improvement of accuracy and reliability, but even worse they can adversely impact engineering judgment. In today’s construction world, it is possible to gather installation information which can be of outmost importance for the final deep foundations performance. Therefore, the increase or decrease of installation reliability through adequate pile testing and performance monitoring should be emphasized and should be taken into account in the codes. This is the case already in most advanced codes, but in a limited and insufficiently refined way. After reviewing how codes deal with this issue today, we will show some recent examples of unexpected results due to pile installation. We will try to put these examples into a broader perspective by highlighting some reference and/or recent literature considerations. Finally we will try to summarize how pile testing and installation documentation can increase reliability and attempt to open the debate on how codes could/should allow for more engineering judgment."

Jan 1, 2014

By F. Terblanche, M. Holton, A. Kruger

The paper presents an optimal mine planning system designed to simultaneously optimize all the underground mines of large South African gold and platinum mining corporations. The system, code named PlanIT-OPTIM, is a multi-stage solution involving the use of adetailed 3D CAD-based mine planning system (CADSmine™V4). The mine design and scheduling rules defined in CADSmine™ are responsible for simulating mining sequencing, rock mechanics, and ventilation, etcetera. Feasible production ranges generated by CADSmine™ and various high-level mathematical models are used as inputs to a mathematical optimization engine. The optimization engine produces optimal production profiles (i.e. key business indicators such as tonnages, mineral and areas extracted per time period) by maximizing net present value. Other objectives such as profit continuity, production continuity and maintaining available reserves can also be specified as optimization criteria. The final step in the PlanIT-OPTIM process is to convert the optimal production profiles into practical and attainable business plans. This is achieved through the CADSmine™ Detail Optimization Engine that modifies the original CADSmine™ schedule to match the optimal production profiles. With current methods it is an impossible task to find the best business plan for a mining corporation in any reasonable period of time should conditions change (e.g. gold prices, exchangerates, grade estimates, etcetera). The fast turn around time achieved through PlanIT-OPTIM makes it possible to do several ‘what-if’ scenarios in a reasonably short time. PlanIT-OPTIM has already been used in the gold mining industry to find optimal business plans for a mine.

Jan 1, 2003

By Alan A. Campoli

The U.S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996

By A. Noble

Traditional simulations of mineral processing circuits are solved by straightforward numerical techniques which require iteration to accommodate recirculating loads. Depending on the complexity of the simulated circuit, this solution technique can be inexact, computationally intensive, and potentially unstable. In this communication, an alternate calculation approach is presented, wherein an exact analytical solution is determined as a function of the individual units? separation probabilities. All the stream data, including recirculating loads, may be solved simultaneously, negating the need for iteration. Furthermore, with an analytical solution available, circuit analysis may then be utilized to diagnose the relative separation potential of the circuit. By integrating these tools, the authors have developed a software package for evaluating circuit configurations. This paper presents the theory, development, and limitations of the software?s methodology along with industrial examples which highlight the tool?s applicability to industrial circuits.

Jan 1, 2012

By A. R. Gaba

Phase I of the Canary Wharf development in London's docklands involves the construction of six fifteen storey buildings located predominantly over water of the West India Docks. The buildings are supported on some 1000 No., 25m long, open ended steel tubular piles driven through 10m of dock water to found in dense sand at a depth of about 15m below dock bed level. The piles are of composite section with reinforced concrete within the upper 17m of the steel tube. Three trial piles were installed in the dock to investigate the driveability and performance of the driven steel tubular piles. The piles were subjected to dynamic and static load testing. Loads were applied in both vertical and horizontal directions. Vibrating wire strain gauges were installed on the inside of the steel piles, on the reinforcement and in the concrete to determine the relative proportions of the applied load carried by the steel tube and concrete infill and to establish how these proportions varied along the length of the piles. Inclinometers were also installed to monitor the lateral deflection of the piles. This paper describes the driving, construction and testing of the three trial piles. The results of the vertical and horizontal loading tests are discussed and comparisons are made between dynamic and static tests carried out on the piles.

Jan 1, 1989