Search Documents

By E Rojas, C Pardo

The exploitation of primary ores using cave mining caused new challenges at the El Teniente mine that required changes to a number of conventional cave mining practices. For example, in the 1970s and 1980s, panel caving was introduced to manage certain geotechnical and operational conditions. Today, El Teniente mine is facing new challenges associated with deep cave mining and establishing its New Mine Level (NML) project, which is located 240 m below the Esmeralda operating cave.The engineering and development phases for this new project have been largely based on experience and lessons learned throughout the history of primary ore exploitation at El Teniente mine, particularly knowledge about seismicity control, the management of collapses and operational practices. For example, previous experience demonstrated that seismicity could be managed by preconditioning using large-scale hydraulic fracturing (HF). HF has been systematically applied in the column of ore above the undercut planned for the NML project and below the production or extraction level, where the main ventilation and haulage infrastructure are to be located.This paper discusses how this has been achieved and is based on previous experience of preconditioning using HF, which has been applied in the selection and management of exploitation techniques and associated planning strategies and design parameters for the NML project.CITATION:Pardo, C and Rojas, E, 2016. Selection of exploitation method based on the experience of hydraulic fracture techniques at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By C. Özgen Karacan

The formation of the gas emission zone in longwall mining and the potential amount of gas in this zone are factors of local geology and spatial variability within this geology. Therefore, geostatistical methods can be used for modeling and prediction of gas amounts and for assessing its uncertainty in the gas emission zone of longwall mines. This study used core data obtained from 64 exploration boreholes drilled from the surface to the bottom of the Pittsburgh coal seam in a mining district in the Northern Appalachian basin. After identifying important coal layers for the gas emission zone, semivariogram modeling was conducted for different coal seams to define the distribution and continuity of various attributes. Sequential simulations were performed for stochastic assessment of these attributes to calculate gas-in-place (GIP) in each coal seam. GIP calculations for coals of various gas emissions zones were combined and ranked for their cumulative distribution function to find GIP in the caved zone and in the fractured zone at the 5%, 50%, and 95% quantiles. Fifty percent quantile results were later used to isolate a panel from the whole area and create a mosaic representation corresponding to the daily advance rate of the longwall face. This approach helped to estimate the daily emissions of this panel from the caved zone and from the fractured zone. Results showed that gas-in-place in the Pittsburgh coal seam, in the caved zone, and in the fractured zone showed spatial correlations that could be modeled and estimated using geostatistical methods. This study showed that gas-in- place volumes in the study area may be as high as 12.3 Bscf and as much as 3.5 MMscf per acre of mining.

Jan 1, 2012

By Fábio de São José

Sistemas de moagem são projetados baseando-se, entre outros parâmetros, no consumo de energia das rotas existentes. Consideram-se custos com energia um desafio para a indústria mineral, pois a maioria da energia disponível ao processo é inevitavelmente absorvida pelos equipamentos e somente uma menor porção é destinada à fragmentação desejada. Hoje, a maioria das teorias utilizadas na avaliação do desempenho energético parte dos estudos de pesquisadores como Fred Chester Bond. De acordo com Bond, Work Index (WI) é um parâmetro representativo da resistência à moagem do minério, servindo para medir o consumo de energia na fragmentação e para comparar o comportamento de diferentes minérios. Estudos recentes comprovam que o WI de materiais em mistura pode ser medido, geralmente, com alto desvio devido às diferenças existentes de moabilidade de cada tipologia. Este trabalho consistiu na determinação do WI de minério de zinco silicatado com elevações nos teores de esfalerita (ZnS) e galena (PbS), devido à avanços na lavra, minério composto unicamente por willemita e suas misturas. Valores encontrados mostraram que a presença significativa de minerais de classes distintas daquele predominante na frente de lavra pode influenciar na determinação de parâmetros importantes para o processamento mineral. Amostras foram fornecidas pela Votorantim Metais Zinco.

Aug 8, 2018

Abbey, Robert Graham, District Mgr. The W W. Sly Mfg. Co,. 50 Church St, New York, N. Y. '21 Abbott, A. N., Mines Supt., Mazapil Copper Co., Ltd ..Concepcion del Oro, Zac., Mexico. '23 Abbott, Argyle Campbell, Dev. Dept, E I du Pont de Nemours & Co, Wilmington, Del. '29 Abbott, Clarence E., V.P, Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co, 1242 Brown-Marx Bldg, Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Elkhorn Div., Consolidation Coal Co, Jenkins, Ky. '15 Abeel, George H., Jr., Cons. Min. Engr Box 427, Santa Monica, Cal. '18 Abel, Albert E., Asst. to Pres, Valley Mould & Iron Corp Hubbard, Ohio. '19 Abel, Raymond L., Asst. Prof., Dept. of Pet Refin., Univ. of Pittsburgh Pittsburgh, Pa. '28 Abell, Leo M., Research Engr, Sullivan Concentrator Chapman Camp, B. C., Canada. '31 Abernathy, George Elmer, Prof. of Geol. & Min . Kansas State Teachers College, Pittsburg, Kans. '20 Aborn, Robert H., Research Lab, U. S. Steel Corp. Lincoln Highway, Kearny, N. J. '19 Abozeid, Mahmood, Dept. of Mines & Quarries Cairo, Egypt. '26 Abraham, Arthur W. Box 1466, Bakersfield, Cal. '20

Jan 1, 1923

By J. E. Lawver, B. J. Clingan, R. E. Snow

Response surface methodology is a well-known and powerful technique for determining optimum conditions in flotation systems. One disadvantage is the onerous task of the numerical calculations and curve plotting. This paper describes a system in which the investigator simply selects the range of several flotation variables after which the design of the experiment, data analysis, generation of response surface equations, and response surface plots are automatically carried out using a digital computer and a computer-driven curve plotter. Several typical response surfaces of important variables in phosphate flotation are presented as examples.

Jan 1, 1980

The U.S. Bureau of Mines conducted a series of laboratory tests in a full-scale model to determine the respirable quartz dust capture efficiency of an irrigated-filter collection system while testing different filter densities, different filter materials, preconditioning water sprays, and wetting additives in the spray water. Impactor samplers were operated upstream and downstream of the filter unit to determine overall dust collection efficiency. The impactor filters containing the 0.7-to 4.7-J.l-m size fractions were analyzed for quartz content, and these data were used to calculate quartz dust collection efficiency. The results of this testing indicated that (1) increased ftIter density improved quartz dust collection, but also resulted in a significant increase in pressure drop across the filter, (2) an alternate synthetic filter material improved dust collection without increasing pressure drop, (3) preconditioning sprays mounted in the system ductwork can have a beneficial effect on dust collection, and (4) additives to the spray water did not significantly increase dust collection.

Jan 1, 1990

By J. K. Richmond

This is a progress report summarizing more than 5 years of a long-range Bureau of Mines research program. The purpose of this program has been to investigate the fire and explosion properties of Green River oil shale in the Bureau's Experimental Mine, in laboratories, and in the field. The lean limits of explosibility of oil shale dust, by small-and large-scale tests, are reported as a function of grade, ignition source, and particle size. A limited number of laboratory tests on the autoignition of oil shale dust layers and the spontaneous combustion tendencies of oil shale are described. Moderate-scale rubble fire tests were conducted to determine flame spread rates as a function of ventilation flow. With the aid of a system to continuously monitor methane emissions in a deep oil shale mine, the characteristics of the methane flow are reported as a function of ventilation and blasting procedures, and are compared with gas yields from core samples. Tentative predictions as to the emission of the methane to be expected in deep oil shale mines, far from the outcrop, are offered. Brief reference is made to a parallel investigation into the fire and explosion hazards of oil shale mining and processing by a Bureau contractor; detailed results of the latter investigation are to be found in the contractor's reports.

Jan 1, 1982

By J Mercuri, S Dunford, P Rothman, E Bartsch, J Snyder, D Newton, R Maron, D Cirulis

The purpose of a mineral comminution circuit with a ball mill running in closed-loop with a hydrocyclone classification cluster is to feed the downstream process with the target particle size. Maintaining the optimal particle size in the flotation feed can significantly improve plant cash flow. In particular, reducing the amount of coarse material is often a major challenge. Existing instrumentation to provide particle size measurement is considered standard equipment in most modern concentrator plants. However, availability is often very low, mainly owing to high maintenance requirements of the analyser and associated sampling system.CiDRA Minerals Processing has developed two novel and robust technologies that address this challenge by providing high reliability and very low maintenance systems for on-line measurement of coarse material in the overflow of individual hydrocyclones. The first system is non-invasive and measures pebbles and rocks greater than 6 mm. This paper focuses on the second system, which is a ruggedized wetted sensor design with no moving parts and provides a real-time trend of the desired target grind size parameter, such as percentage above 150 micron.Both systems have simple robust designs and measure in the primary overflow stream of the individual hydrocyclone. Individual hydrocyclone measurement enables identification of poor performing hydrocyclones in addition to providing a representative measurement of the whole hydrocyclone cluster. The systems do not require sampling and associated sample transfer piping circuits that are prone to plugging, thus avoiding high maintenance requirements.The wetted sensor will be described in detail along with its implementation in a robust control scheme in a major copper concentrator in North America. Plant data shows very high availability, achieved with very low maintenance, has enabled improved process control, thereby maintaining throughput and ball mill target power while reducing grind size.CITATION:Cirulis, D, Dunford, S, Snyder, J, Bartsch, E, Rothman, P, Maron, R, Newton, D, O’Keefe, C and Mercuri, J, 2015. Process optimisation using real-time tracking of coarse material in individual cyclone overflow streams, in Proceedings MetPlant 2015, pp 93–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Victor R. Spironello

The Bureau of Mines has studied slags associated with ferrous melting, to evaluate substitutes for the auxiliary flux mineral, fluorspar. A waste material recovered from alumina reduction cells, "used potlining," was tested in an 18-in-ID basic-lined cupola and in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF). One potlining fraction, No. 1 cut, is a carbonaceous (graphitic) material and represents the bulk of the entire cell lining. The other fraction, No. 2 cut, is a refractory backup. These materials contain significant quantities of fluorine and other elements fn various compounds. The potlining fractions were blended in ratios believed representative of available materials. Both lump and pelletized forms provided extremely fluid slag. No adverse effects were found on furnace performance, chemistry or strength of the metals produced, or the environment. Fluorine recovery in the slag and fluorine losses to the scrubber water and solids were about the same as when fluorspar was used. There was apparently no lining loss from the cupola, but there was lining attack in the BOF. Since the fluidizing ability of potlining is due in part to sodium and other elements such as aluminum and silicon, less fluorine is needed in the slags when potlining is used.

Jan 1, 1983

By David E. Fogelson

One model each of three different makes of portable displacement seismographs was calibrated on a shaking table capable of 5,000 pounds of force, Calibration tests were conducted in the frequency range of 5 to 200 c.p,s, and in the amplitude range of 0,002 to 0.05 inch peak-to-peak, The seismographs were tested under two mounting conditions: (1) The feet of the instrument were bolted to the shaking table, and (2) the feet were resting on emery cloth affixed to the table, The results of these tests show that, in the frequency range of 5 to 40 c.p,s, and for vibration levels less than 0.2 g, the magnification for all three instruments is constant with input level but varies slightly with frequency. For vibration levels greater than 0.4 g. and for frequencies greater than 40 c.p.s., the magnification of all three instruments shows large variations with frequency and amplitude of table motion.

Jan 1, 1962

By L. J. Gardner

Ore pass systems play a critical role in moving broken rock from the workplace to surface, and the integrity of the ore pass excavations is crucial. Over the life of the mine, ore pass integrity deteriorates, which may eventually result in the ore pass no longer being fit for purpose. This paper presents several case studies of successful ore pass rehabilitation exercises.

Jan 1, 2006

By F. G. Scott

This document is a proposed program plan for mining environmental research to be conducted by the U.S. Bureau of Mines in support of industrial oil shale mining and processing. This program plan is one of three research alternatives being considered by the Bureau, each based on a different level of anticipated funding. This report documents the mid funding level program plan.

Jan 1, 1980

By Mark Sanders

This report describes an experiment which was conducted to compare the relative bumping hazard of a low and high profile hard hat (helmet) in a low seam mining environment. The study was specifically designed to assess the effect of lowering the helmet profile on frequency of head impacts in an underground low seam coal mine simulator. This involved subjects performing four common low coal mining tasks wearing the low and high profile helmets in the low seam simulator (36" and 48? heights). The results of the study indicated that a low profile helmet could reduce bumping frequency in underground low coal approximately 25%, and as much as 80% on selected tasks. It was beyond the scope of the study to measure the impact force, thus it was not possible to estimate the effect of the low profile helmet on severity of impacts underground. The research team recommended that a more extensive investigation be made of head injuries experienced in low seam mining (both underground and surface) with the objective being to assess the impact of a low profile helmet on total head accident exposure.

Jan 1, 1980

By Barry D. Lichter, Pierre Sommelet

High-temperature heat contents of InAs and GaAs were measured over the temperature range 400°K to temperatures above the melting points using a di-phenyl ether drop calorimeter. Smoothed values of the thermal properties have been derived and tabulated at even temperature interuals . The heats of fusion of InAs and GaAs were determined as, respectively, 8790 ± 200 and 12,590 ± 300 cal per g-atom at the respective melting points of 1210º ± and 1513º ± 1°K, yielding entropies of fusion of 7.26 * 0.16 and 8.32 ± 0.20 cal perºK per g-atom, respectively. A general discussion of the thermal properties of III-V com-pounds is given. THE low-temperature heat capacities of InAs and GaAs have been determined by Piesbergen.1Using a dynamic temperature modulation technique, Miller2 has determined the heat capacities of the compounds as well as GaSb and Ge between room temperature and 650°K; however, it has been observed that values determined by drop calorimetry for GaSb3 and for germanium4 are consistently about 5 pct lower than Miller's results. Cox and Pool10 report values for the heat content of InAs and GaAs and the heat of fusion of InAs. No value for the heat of fusion of GaAs appears to have been previously reported. This paper reports results of high-temperature heat content investigations of InAs and GaAs measured in the range 400" to above 1500°K employing a diphenyl ether drop calorimeter. These results, together with our previous results on III-Sb compounds3 as well as heat-content measurements5 of solid InP and Gap, are used in a general discussion of these compounds. EXPERIMENTAL PROCEDURES High-purity samples of the compounds, stoichio-metric to ±0.1 at. pct, were supplied in the form of crushed crystal fragments by Dr. Carl Thurmond of the Bell Telephone Laboratories. The sample preparation, description of the calorimeter, and details of the heat content measurement have been previously described.3 Samples were sealed in evacuated silica capsules and suspended by a Pt-Rh wire in a Pt-wound vertical tube furnace, heated to temperature

Jan 1, 1970

By Richard F. Lynch, Frank E. Goodwin

"The development of Galfan, a new generation 95% zinc-5% aluminum-mischmetal alloy coating for steel, offers opportunities for greater fabrication flexibility and upgraded corrosion performance in automotive applications. The formability of Galfan is equivalent to that of electrogalvanized steel, based on laboratory tests and automotive component fabrication. Corrosion resistance of Galfan exceeds that of hot dip and electrogalvanized, including performance in automotive industry tests. Automotive production applications for deep drawn and stamped components in France and Germany are based on the ability to meet dual performance requirements for upgraded formability and corrosion resistance. The first U.S. Galfan application was on 1985 model Ford cars and light trucks for transmission oil cooler lines which has now expanded into a number of power steering tubing uses. IntroductionContinuing requirements for improved vehicle performance coupled with the ever present need for reduced cost have spawned the development of a number of new coated steel products. Among this new generation of coated steels is Gaifan™, a 95070 zinc-Solo aluminum-mischmetal hot dip alloy coating. Galfan exhibits particular promise for automotive use based on broad fabrication advantages and upgraded product performance(I ),The unique characteristic of Galfan is the key combination of greatly improved formability with much longer corrosion life. Galfan provides significantly better formability than any other hot dip coating. Testing shows that formability is limited primarily by the steel substrate to which the Galfan coating is applied. Galfan exhibits excellent resistance to flaking and microcracking during commercial forming operations. The result is the elimination of unnoticed damage to the coating which would show up later as premature rusting on the finished product."

Jan 1, 1987

OBJECTIVES ??REDUCE OPERATING COSTS ??INCREASE LIFE COMPONENTS ??EXTEND LIFE of THE DOZER ??REDUCE MAINTENANCE COST ??REDUCE DOWNTIME ??IMPROVE DURABILITY & RELIABILITY ??IMPROVE BOLD JOINTS PREFORMENCE ??IMPROVE SAFETY

May 1, 2004

The Tenth International Conference of Directors of Safety in Mines Research was held in the United States from September 28 through October 2, 1959, at Hotel Webster Hall, Pittsburgh, Pa. The Conference was organized by the Federal Bureau of Mines. In accord with the program outlined at the Ninth Conference (1956, Heerlen, Holland), the papers submitted dealt with the following three subjects: 1. Safety of coal mine explosives 2. Explosion hazards in mines 3. Ignition and fires in mines Seventy papers were presented. There were eight technical sessions followed by an extended tour of the Bruceton facility of the Bureau of Mines on October 2. Simultaneous translation was provided in the three official languages of the Conference--English, French, and German.

Jan 1, 1962

By Marcel Vanpee

Eight extinguishing powders KCI, were tested on five types of diffusion flames. The effect of flame temperature on the inhibition efficiency was investigated by varying the oxygen index of the flame supporting atmosphere. Inn addition a spectrographic investigation of powder flame dissociation products was carried out on the methane/air/ABC (NH4H2PO4) flame. Dissociation products for this flame included P0, PH, NH, and Na. It is concluded that the main factor to be considered in the efficiency of tie powder is the flame temperature Purple K (KHC03) was typically inefficient in low temperature flames and very efficient in high temperature flames. On the other hand, ABC (NH4H2PO4) was found to lose its efficiency at high temperature but to be quite efficient in the low temperature flames. The effect of temperature is offered as an explanation of the poor efficiency of Purple K (KHC03), against coal dust explosions as contrasted to the high efficiency of phosphate salts against coal dust explosions.

Jan 1, 1982

By K. Janghorban

Multilayered ceramic-metal composites were produced by solid state diffusion bonding of polycrystalline alumina and three Al alloys containing 1 to 2%Sr, 2% Mg and Mg + Si (5057 Al alloy), The multilayered structures were fabricated at 610°C under a compressive stress of 3 MPa for 2 hours in He-5%H atmosphere, The ceramic-metal interfaces were studied by SEM and TEM equipped with energy dispersive spectrometer (EDS). Addition of 1 wt % Sr to Al promoted good adhesion, without producing any interfacial products, while the Al-2%Sr was poor in this regard due to the presence of dispersed A14Sr which is an intrinsic phase in the Al-Sr phase system, The Al-2%Mg alloy produced a continuous film at the interface, which was characterized to be MgAl2O4. Al alloys containing Mg and Si (5057 commercial alloy) produced not only the spinel structure (MgAl2O4), but another phase rich in Mg and Si (close to Mg2Si), These latter interfacial reaction products were not the intrinsic phases in Al-Mg alloys, and were reaction products at the Al2O3 ?Al alloy interfaces.

Jan 1, 2005

S.L. Barua and Y.C. Kim M. Armstrong's paper is very interesting and can be regarded as a pioneering work of applying geostatistics on washed coal. The density levels used in her study are uniformly spaced, which facilitated curve fitting through a proper experimental design. Most of the existing coal washing plants in the US, however, gather washability data at non-uniform intervals which, in turn, affects the goodness of curve fitting. We would like to emphasize the importance of having a proper experimental design, if a similar geostatistical application is to be conducted on washed coal. We, at the University of Arizona, tried the variogram on recovery (Kim, Barua, and Baafi, 1982, SME preprint 82-143) which showed a similar pattern as Fig. 4 of Armstrong's paper. In both cases, the first experimental variogram value is invariably and inexplicably higher than the second variogram value. Although Armstrong ignores the first point because of "small number of sample points," we did not do so because there were 17 sample pairs. As a consequence, we concluded that the obtained experimental variogram was unsatisfactory and that further research is warranted. In other words, this disagreement in variogram interpretation between M. Armstrong and the University of Arizona begs the question whether the experimental variogram of Fig. 4 truly reflects the spatial correlation in washed coal, assuming there is such a correlation. Finally, we wish that Armstrong could have done a similar study on clean sulfur, which is a vital interest to the coal mines in the US. Her implied remark on sulfur in the concluding section of the paper may turn out to be incorrect because our experimental variograms on clean sulfur at different density levels were even less satisfactory than those on recovery.

Jan 1, 1985