Search Documents

By J. L. Bruce, G. W. Nicolson

ThE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydro-thern~ally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CeMent and Concrete Linings During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, howcver, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 11\2 pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with 12 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concretc and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1949

By R. E. Hobart

The development of the Hauto power plant and the claims made by various engineers that electricity was more economical than steam for power purposes in and about the mines, led the Lehigh Coal and Navigation Co., in 1911, to conduct a test to ascertain the consumption of power used by a large steam hoisting engine. The question being one on which no reliable information could be found, and the opinion of various engineers differing to such an extent, it was decided that a test under actual operating conditions was necessary. This was arranged for at one of the collieries. The engine selected was 2 30 by 60-in. (76.2 by 152.4-cm.) piston-valve engine of modern type, and comparatively new. The boiler plant from which the hoist received its power was about 600 ft. (182 m.) from the engine, the latter being fed by a 10-in. (25.4-cm.) steam line insulated with magnesia pipe covering. Two batteries of the boiler plant, aggregating 1200 hp., were cut off and fed into a separate steam line leading direct to the hoist engine. Steam auxiliaries, consisting of feed-water pump and blowers, were fed by the boilers in test, and their consumption charged against the hoist. A barrel weighing device was installed, as it was felt that this would be the most accurate way of determining the consumption of water. The fuel, No. 3 buckwheat, was carefully weighed, and every precaution was taken to make the test accurate in every particular. The test was run for 1 week, or a total of 168 hr. A record was kept of the number of trips hoisted or lowered, and continuous indicator cards were taken. One particular set of cards was taken with the hoist operating balanced, and also with the hoist operating with no counterweight other than the empty cage, the coal in the car being weighed. The speed of the hoist was taken by means of a graphic recording instrument which registered the number of revolutions every 5 sec. From this record, speed-time curves were plotted.

Jan 1, 1918

By C. E. Sims, G. A. Moore, D. W. Williams

During the past several years, the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture, and the ductility values can often be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging. The cure of such an abnormal condition represents a real improvement in the quality of the steel. Several types of abnormal loss of duetility can be distinguished, of which those caused by excessive amounts of inclusions of undesirable type and those caused by unsuitable grain size and inget structure are well known. The particular type of abnormal lowered ductility currently under consideration may be distinguished by the fact that the low-temperature aging treatment necessary for its relief is insufficient to cause any visible change in the micro-structure as ordinarily observed. As this aging will in fact eventually occur at room temperature, the phenomenon of present interest may be given the symptomatic definition, ''Temporary Abnormal Low Ductility." Some hundreds of previous investigations, largely qualitative in nature, have established, beyond reasonable doubt, that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary abnormal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, The Steel Founders' Society of America has, since Nov. 1, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-duetility effects and porosity. The interest of this investigation thus extends to permanent abnormal losses of ductility, such as are caused by the inclusions which sometimes result from special deoxidizing practices and possibly from metallic nitrides, but as these can he distinguished from the temporary effect of hydrogen, they have been excluded from the work reported here except when they

Jan 1, 1949

By A. D. Schwope, L. R. Jackson, A. M. Hall

IN the course of an extensive investigation of the comparative properties of several types of copper, data were obtained on the cold working and subsequent recovery and recrystallization of the copper. In this paper, relations between the degree of cold work and the course of recrystallization are developed. In particular, it is shown that the course of recrystallization over long periods of time and at low temperatures can be predicted with reasonable accuracy from short-time high-temperature recrystallization data. MATERIALS USED IN THE INVESTIGATION Three types of copper were used in this investigation; these were tough pitch, OFHC, and OFHC copper with 15 oz per ton of silver added identified herein as Lots C, D, and F, respectively. The material was supplied by the American Metal Co. Ltd., and processed by the Rome Cable Co. The analyses of the three types of copper are given in Table 1. Originally, it started as wire bars 4 X 4 X 54 in. These bars were heated to 871°C in air and hot rolled to 3/8 in. rod. This rod was cold drawn to 0.204 in. rod (70 pct reduction) in three passes and annealed at 427°C for 4 hrs. A portion of the 3/8 in. rod was saved for more detailed cold-drawing experiments. Starting with the annealed 0.204 in. rod, hard-drawn wires were produced by cold drawing to 0.081 in. wire in 7 passes (84.4 pct reduction in area). Half-hard wires were made by cold drawing the 0.204 in. rod to 0.102 in. wire, (75 pct reduction) in 6 passes and annealing at 427°C for 4 hrs. This annealed wire was then drawn to 0.081 in. wire, (37.1 pct reduction) in 2 passes. Square rod was made by hot rolling wire bars to 9/16 in, rod in 8 passes. This rod was then cold drawn to 0.445 in.-diam rod and annealed for 3 1/2 hrs at 538°C. It was then cold drawn to 0.325 in. rod and again annealed at 538°C for 3 1/2 hrs. Hard square rods were then made by cold rolling this material to 0.257 X 0.257 in. rod, a reduction in area of 20.5 pct. Half-hard square rods were made by cold rolling to 0.268 X 0.268 in. square, annealing for 332 hrs at 538°C and cold rolling to 0.257 X 0.257 in., a reduction of 8.5 pct. Soft wire or rod was made from all types of copper by annealing the hard-drawn material at 343°C for 3 hrs in steam. The grain size of the annealed 0.081 in. wire varied slightly among the three lots: from 0.015-0.025 mm in the silver-bearing OFHC to 0.035-0.045 mm in the OFHC copper. The annealed 0.257 in. wires were more uniform in grain size, averaging about 0.035-0.045 mm. Representative structures are shown in Fig I. EFFECT OF COLD DRAWING AND TENSILE STRAIN ON STRENGTH OF COPPER Conventional tensile tests were performed on the three types of copper in the various degrees of hardness described above. Results of these tests are tabulated in Table 2. The results in Table 2 are

Jan 1, 1947

By Walter Crafts, C. M. Offenhauer

IN the course of study of the heat-treatment of low-alloy steels, the behavior of alloy carbides at subcritical temperatures was found to vary from that indicated by published investigations. In order to establish the ranges of formation of carbides in low-chromium steels, a series of steels containing up to 0.60 per cent carbon and 7.5 per cent chromium has been investigated with respect to the type of carbide formed after quenching and tempering at subcritical temperatures. The types of carbide formed as products of austenite transformation to pearlitic and pseudomartensitic structures have also been determined. There have been numerous investigations of the carbides in chromium steels and diagrams of the iron-chromium-carbon system.1 Westgren, Phragmén and Negresco2 identified the following carbides in chromium steels: [Cementite Fe3C (containing up to about 15 per cent Cr) Trigonal carbide Cr7C3 (containing up to about 55 per cent Fe) Cubic carbide Cr4C (or Cr23C3) (containing up to about 25 per cent Fe) Orthorhombic carbide . Cr3C2 (containing only a few per cent Fe)] The most complete information on the iron-chromium-carbon system was supplied by Tofaute, Sponheuer and Bennek3 and by Tofaute, Küttner and Büttinghaus.4 By means of dilatometric and microscopic studies, sections of the diagram were established. This diagram showed the presence of the special carbide Cr7Ca in steels containing about 2.5 per cent to 12 per cent chromium in low-carbon steels and from about 5 to 20 per cent chromium in r per cent carbon alloys from A1 to room temperature. The present investigation has shown that a carbide inversion from Fe3C to Cr7Ca occurs in chromium steels containing more than about 1 per cent chromium after hardening and tempering at subcritical temperatures above about 500°C. The type of carbide observed to be more stable in quenched and tempered specimens was also found to be produced by direct austenite transformation in corresponding ranges of temperature and composition. EXPERIMENTAL PROCEDURE The steels used in these experiments were made in magnesia-lined crucibles in high-frequency furnaces and were poured into 2-in. ingots. The ingots were forged into 1-in. round bars, and all heat-treatments were conducted on specimens of this section .size. Sections of the bar stock 8 in. long were hardened in air, oil or water depending on the composition, after heating to a temperature sufficiently high to dissolve the carbides. The low-carbon and low-chromium steels were not entirely martensitic after quenching, and contained some ferrite and pseudomartensite. No pearlite was observed in the microstructures after auenchine. The quenched bars were cut into

Jan 1, 1942

By John D. Sullivan, Edwin J. Rogers, Chester R. Austin

The problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce lightweight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough qo that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an - outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays† and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, partitularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating."² The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the Purpose Of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942

By Frederick L. Knouse

The south border of Espirito Santo begins about 400 km. north of Rio de Janeiro and extends along the Atlantic Coast northward some 325 km. and inland 100 to 150 km. The area under consideration, where quartz crystal of strategic grades has been mined, extends from 19º to 21º and 30º south latitude; and from 40º to 41º and 30º west longitude. This includes the central part of Espirito santo, chiefly south of the Rio Doce from the Atlantic ocean, and west across the border into Minas Gerais near the town of Aimores, in the municipalities of Aimores, Minas Gerais; Baixo Guandu, Santa Teresa, Santa Leopoldina, Colatina, Joao Neiva, Fundao and Domingo Mar-tines, Espirito Santo (Fig. I). During 1943 and the first half of 1944, this region accounted for approximately 3 to 5 per cent of the quartz crystal produced in Brazil. Shipments of crystal have been made chiefly by rail to Rio de Janeiro. This region is serviced by the E. F. Minas-Vitoria and E. F. Leopoldina to Rio de Janeiro through vitoria; and by the E. F. Minas-Vitoria and E. F. Centra] do Brasil through Bello Horizonte, Minas Gerais to Rio de Janeiro. The major deposits are accessible from the railheads by dirt roads, some being 5 to 30 km. off the road, reached by trail. In 1943 and the first half of 1944, the bulk of the production was from inter- mountain marshes and adjoining hillside alluvial placer deposits in the zone surrounding the town of Santa Teresa. Most of these deposits were formed from the erosion of pegmatite~, quartz veins and pockets in the gneiss, with minor quantities produced from miarolitic cavity fillings in the granitic rock. Early Operations Mining of quartz crystal in this region began in 1928 and has been stimulated by the market demand for military uses. Before 1936 little attention was given to it, either in Espirito Santo or eastern Minas Gerais. From 1936 to 1941 the Japanese sent agents to various points of production or potential production to acquire quartz through purchase. They bought crysta1 as small as 10 grams. Since '94' only the United States and Great Britain have received quartz from Brazil. The United States purchases crystals of 100 grams and larger for strategic purposes. The first known discoveries were made either in the municipalities of Aimores, Minas Gerais, or in Baixo Guandu, 01 Domingos Martines, Espirito Santo. Marketable quartz crysta1 was first found either in the massive quartz replacement veins of the Victor Hugo mine in the municipality of Domingo Martines, or in the large 'ores of quartz in the pegmatites near Baixo Guandu, extending into Minas Gerais. Production The production of quartz in Espirito Santo from 1936 through 1941 as recorded

Jan 1, 1948

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employ¬ment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, how¬ever, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong. SEC. 4. -Senior Members: The Directors may in their discretion place on the Honor Roll of Senior Members and transfer from any other class of membership other than Honorary Membership the name of any Member or Associate who has reached the age of seventy years and who has paid dues for thirty years, and for good reasons in special cases may vary the age or number of years. SEC. 5. Junior Members: A person to be eligible for election to the class of Junior Member must be qualified through education or experience to hold a subordinate position in engineering, mining, metallurgical, geological or chemical work. He shall be not more than 33 years of age at the time of election. SEC. 6. Associates: A person eligible for election or transfer into the class of Associate shall be one, who, in the opinion of the Committee on Admissions and the Board of Directors, is suitable for such election or transfer by reason of his interest in or connection with mining, geology, metallurgy, or chemistry. SEC. 7. Rocky Mountain Members: Membership in a special class of life member¬ships without annual or other dues and without right to receive the printed literature distributed to other members or the right and privilege of wearing the official badge of technical members, is given to all members of the Rocky Mountain Club at the time of consolidation. These special Rocky Mountain memberships shall be claimable by any member of the Rocky Mountain Club, not already a member of the Institute, availing himself of the privilege within ninety days after mailing of notice to him, by the Secretary of the Institute. SEC. 8. Junior Foreign Afliate: Upon appropriate action by the Board of Direc¬tors and with its approval, members in good standing of any technical society having its headquarters outside of the United States of America, Canada, or Mexico,

Jan 1, 1937

By J. Charles Miller

NATURAL carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inorganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of fumaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the producing formation is recommended, The Farnham anticline is used as an example and cornputationa are made of the probable volume of gas originally present in the structure. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate. INTRODUCTION Carbon dioxide, in liquid and solid form, has found a wide variety of uses other than its primary application in carbonating beverages. It is now used in more than 40 different ways, ranging from cooling or freezing to use in gas or liquid form for mechanical purposes, chemical industry, explosive, fire extinction, and tire manufacturing. Undoubtedly the chief supply of carbon dioxide is obtained from industrial plants or artificial sources and until recently natural deposits of the gas have received little consideration. Few will question the utility and perhaps dependability of artificial sources, which possess the advantage over

Jan 1, 1937

J. B. Cohen (AVCO Mfg. Co.)-The model presented by the authors is only one of several possible mechanisms for low-temperature aging. It is true that the motion of dislocations to the copper atoms, followed by diffusion along the dislocation lines, is one such mechanism. However, the details of such a process which would :result in copper-rich platelets on (100) planes in the f.c.c. matrix are not clear. Furthermore, there is at least one other mechanism that may be used to e.xplain the authors' results, so that the data do not clearly favor the Turnbull model. The zones may form by "normal" diffusion. The diffusion constants would be higher at room temperature than extrapolated data would suggest due to vacancies trapped in the specimens in the quench. The diffusivity would then be multiplied by the ratio of the number of vacancies present at the solution temperature to that present at room temperature. These vacancies could remain in the alloy specimen for long times at room temerature, due to interaction with the copper atoms. ' The activation energy for diffusion is smaller than that for bulk diffusion at elevated temperatures for it is only that for the motion of vacancies existing after the quench; after these are used up, the aging process effectively ceases. It is somewhat questionable if the laws governing transformation kinetics can be directly applied to changes in elastic moduli, especially in the case of aging where the structure and the composition of the zones may be changing during aging, If such laws are assumed, it is possible to explain the exponential factor of % with this vacancy model. It is probable that the structure of the zones and the matrix match only on (100) planes. Certainly the precipitates that form in this system after various aging treatments show orientation relationships similar to those of the zones. Strains on the edges of the zone may set up fields which do not allow the zone to grow in an edgewise manner. The exponent in the growth of a thin plate in a direction perpendicular to its face would be %. It may also be that copper atoms are attracted to dislocations. If this is the rate-controllin factor in the growth process Ifthisthen an exponent of % or % may arise. The writer would like to know if the authors have tried plotting l/a; proportional to as might be expected for "dislocation drainage." R. H. Doremus (General Electric Research Laboratory)—An important new method for following the growth of Guinier-Preston zones is presented in this paper, and I wish to congratulate the authors on their experiments. Their interpretation of the results, however, is doubtful in certain respects. To determine the exponent m in Eq. [4] the authors plotted -log at against t to various powers (their Fig. 6). The initial value of frequency used for these plots was found by extrapolating the data to zero time. In Fig. A the data from their Fig. 2 are plotted against a linear, rather than logarithmic, time scale. To obtain graphs similar to their Fig. 6 for these data one must use an initial frequency of about 52720; such a plot for m = % is shown in Fig. B. The straight line in Fig. B fits the data in an intermediate range only. The curve drawn in Fig. A was mapped from this line; comparison of

Jan 1, 1960

By G. W. Doepel, W. P. Sibley

A three-dimensional, multilayer, mathematical model has been developed for predicting performance by mis-c.ible displacement. Areal and vertical coverage, total gas-oil ratio, propane-oil ratio and oil-recovery factor for the multilayer system are computed as functions of hydrocarbon pore volumes of solvent injected. The technique has been programed for use on the IBM-7090 digital computer and was used in calculating perfortnance for continuous miscible displacement of a five-spot, 50-layer .system. Results reported are based on the use of published laboratory data for a single, uniform five-spot layer. However, the technique is sufficiently generalized to calculate performance of any system of layers of any pattern configuration and mobility ratio, provided data are available to describe perfortilance of a single layer. The technique has also been adapted for predicting oil recovery resulting from various gas-driven slug sizes. The results presented for both continuous and slug-type injection show, that permeability variation has 0 significant effect on oil recovery but that solvent composition, within the range studied, has a lesser effect on oil recovery. INTRODUCTION Experience from many of the miscible-phase displacement projects currently in operation indicates that the injected solvent flows preferentially through the more permeable zones in the reservoir. This preferential solvent flow in the high-permeability streaks results in a reduction of vertical coverage (C,) and an attendant decrease in oil recovery. The multilayer technique presented in this paper uses areal coverage (C.,) data for a single layer from the literature and from laboratory measurements of displacement efficiency (herein referred to as microscopic coverage, C,,) to calculate areal coverage (C,) and vertical coverage (C,) for the multilayer system. Oil recovery for the multilayer system is obtained as the product of (Ca) (Cm) (Cv). It is assumed that C, in a single layer is 100 per cent; therefore, (C,) (Cm) is a measure of oil recovery from that layer. Data presented in the literature for a single layer generally deal only with areal coverage and/or microscopic coverage —but seldom specifically with oil recovery. Nevertheless, this technique is flexible in that either Ca and C,, of an individual layer or a direct measurement of oil recovery for the layer may be used. In developing this technique, the problem arose concerning a method of determining the relative amounts of solvent that will enter each layer during any increment of solvent injected. To solve the problem, a dimensionless equation was derived for expressing solvent injected into each layer as a fraction of total injection. A finite-difference method was applied in integrating the equation to determine oil recovery for the system of layers as a function of pore volumes injected. The technique subsequently was programed for solution on a digital computer. The method was applied to predict performance of a deep California reservoir under continuous miscible displacement and has been extended for calculating oil recovery as a function of slug size for gas-driven slug injection. The technique may be applied to any petroleum reservoir that can be adequately represented as a layered system, by considering permeability variation,1-3 permeability range and average permeability. Each layer is then assigned its appropriate permeability, porosity and hydrocarbon saturation. RESERVOIR VOLUME CONTACTED BY SOLVENT It has been recognized for some time that high microscopic coverage (C,) can be obtained by injecting a miscible agent, such as propane, into an oil reservoir. These high values of C,,, have been demonstrated in the laboratory and are normally between 80 and 100 per cent, depending on solvent and reservoir oil composition as well as on reservoir temperature and pressure. In miscible-phase displacement, because there is no interface between solvent and oil, effective permeability to solvent is the same as that to oil. (This assumes that oil saturation has not changed and that water is immobile.) Consequently, mobility ratio (M) simply reduces to that of viscosity ratio . Perrine4 and Habermann5 have shown that large

By Norman P. Goss

It is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.l-8 The broadening of the Ka lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the diffraction lines are broadened and the Ka doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolution of the doublet is lost when a metal is cold-worked and the Laue spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attributed the hardening to fragmentation of the grains into smaller units. Jeffries and Archer,ll after carefully considering the problem of work-hardening from many angles, came to the conclusion that cold-working mechanically refines the grains into smaller crystal fragments, some of which at least differ in orientation from the parent grain. The increase in

Jan 1, 1940

By C.F. Pascoe, H.J. Roast

The object of this investigation was to compare the arsenical antimony-lead alloy with some of the regular bearing-metal alloys. With this end in view, the following tests were made: 1. Chemical analyses to show the composition. 2. Thermal analyses. 3. Macroscopic examination of fractures. 4.Microscopic examination. 5. Tensile tests. 6. Crushing tests. 7. Scleroscope tests.' 8. Brinell tests, at temperatures from 80' to 400' F. Tests 3 to 8 were conducted on both sand-cast and chill-cast specimens. For the purposes of this paper the alloys have been numbered from 1 to 6; their composition is as follows: Lead. ' Antimony, Tin, CoppeR ARSEnic, NumBeR PeR CENT. PER CENT. PeR Cent. PeR CeNt. PeR Cent. 1 82.64 12.95 4.40 0.01 none 2 27.54 9.04 59.87 2.65 none I 3 none- 0.13 ------------1.47 4 82.95 16.85 none 0.20 none 5 83.78 15.35 none 0.05 0.82 6 0.15 7.87 . 84.13 7.85 none The analysis, in the case of the antimony, was made by solution in sul-furic acid and titrated with permanganate. For tin, the ferric-chloride method was used; for copper, the alkaline separations, and the thio-cyanate methods; for arsenic, volatilization of arsenic and titration with iodine. The lead, with the exception of alloy 6, was taken by difference. With the exception of No. 5, the alloys were taken as received from the manufacturer. About 40 lb, were melted in a graphite crucible and recast into small ingots to insure uniformity of composition; samples

Jan 1, 1923

By Benjamin Lustman, Robert F. Mehl

The study of the high-temperature oxidation of pure metals, intensively pursued experimentally since the pioneer work of Pilling and Bedworth1 and supplemented by the recent theoretical work of Wagner2 is now well advanced. The important field of low-temperature oxidation—i.e., oxidation extending only through the temper color range of thicknesses with the formation of thin oxide layers in the range from 0 to 1000-2000 ?ngstroms—has not, however, reached so satisfactory a state, owing largely to the experimental difficulties that attend the formation and study of thin films; most of the work has been performed on abraded specimens whose surface irregularities approximated the thickness of the films formed. It has been pointed out that the rates of oxidation of different crystal faces are different and that the difierence may be related to the orientation relationships that obtain between the metal crystal and the superimposed oxide crystal; it has also been suggested that this orientation dependence should manifest itself in rates of oxidation and perhaps also of corrosion in aggregates bearing preferred orientations.3'4 An attempt to measure the rates of oxidation of different crystal faces of alpha iron demonstrated this difference in rate,4 but the dependence of rate on orientation was not simple; the method of measuring thickness, consisting of a color comparison with barium stearate multi-films of known thickness, was not wholly satisfactory. For these reasons it was felt that a study of the rate of oxidation of single crystals prepared with surfaces as smooth as possible, using a sensitive method giving true film thickness, should be profitable. Copper was chosen because of the ease of reduction of the primary oxide film and because the orientation relationships between metal and oxide and the composition of the oxide films formed at low temperatures are known; for thin films formed at low temperatures, Cu2O alone occurs.22-24 Experimental Procedure Various methods of surface preparation were attempted in order to obtain a surface that would oxidize uniformly and repro-ducibly. Electrolytic polishing by the method of Jacquet5 and electrolytic and mechanical polishing followed by annealing in vacuum and in purified hydrogen at various temperatures were tested. The procedure finally adopted consisted in a fine metallographic polish followed by an anneal in purified hydrogen at temperatures of 900° to 1000°C. for 12 hr. or more. The surface so produced was very bright and smooth, with no trace of specular etching (though some grain-boundary etching was observed); indeed, fine scratches produced by the final polish were entirely removed by the high-temperature anneal. After this treatment, the specimens were cooled in hydrogen to room temperature and placed in the oxidation furnace, where

Jan 1, 1941

By James J. Bean

HE task of measuring the specific gravity of the -*- operating medium in a heavy-media separation system has never presented a particularly difficult problem because the medium is fairly stable and the overflow of the separatory vessel, as well as its underflow, can be sampled easily and accurately and the specific gravity of the suspension determined easily by weighing a known volume. However, while this method is simple and accurate it does require the operator to take the sample by hand and to weigh it and there is considerable temptation to avoid the periodic sampling if everything seems to be going well, or if something is occupying the attention of the operator. Furthermore all operators do not sample in exactly the same manner and considerable practice is required for two operators to be able to "check" each other to the last few hundredths, particularly if the sample is cut underneath the drainage screen where location of the point of sampling and load on the screens tends to influence the determination. While none of the above presents much of a problem, we have all recognized that some mechanical method of continuous measurement and recording would be advantageous since the operator would merely have to glance at the meter to check the gravity and to have an indication of the trend of any changes. Also if the instrument were of the recording type, a permanent record would be available for the guidance of the superintendent. The Eagle-Picher Mining and Smelting Co. was the first heavy-media user to actually install such a recording meter. In 1946 they installed in their Central Mill at Cardin, Okla., a specific gravity recorder manufactured by the Bristol Co. of Water-bury, Conn. R. A. Barnes, of the Bristol Co., working with E. H. Crabtree, Jr. and Elmer Isern, of Eagle-Picher, made the application and worked out the problems of sampling and measuring. Their attempts to measure the specific gravity of the medium in the cone itself were not entirely successful and they resorted to an outside sample tube for actually making the determination. Because of the particular flowsheet used, it was possible to tap off from the medium return pipeline a stream of medium and divert it into the sampling tube, which was provided with a constant level overflow and a spigot underflow, and into which the bubbler tubes dipped. The Eagle-Picher installation was successful and its possibilities were recognized by the Mineral Dressing Laboratory of the American Cyanamid Co. It was decided to install a similar unit in the heavy-media pilot plant to investigate further its possibilities. Chief among these was the continuous record which it was felt would be proof of the steadiness of the gravity in a heavy-media cone, something which is not always appreciated by POtential users. Because the heavy-media pilot plant is required to operate at a wide range of specific gravities, it was realized that the unit would have to record all gravities from 1.25 to 3.50, and do it to the nearest 0.01. It would not be necessary to record all of this wide range on a single chart and the method selected was to have 4 bands, each band range overlapping the other a small amount and calibrated so that with standard charts one division would represent 0.01 sp gr. A shift from one band to another could be arranged without alteration of the instrument itself, being accomplished by a simple change in the bubble-tube lengths, as described later. Accordingly, a recording type instrument was purchased and installed. Because there were some advantages in doing so, the first installation attempted to measure the gravity of the cone proper by placing the bubble tubes in the cone. This was not at all satisfactory and the second scheme utilized a fixed vertical screen at the surface of the cone, and an external sample-tube arrangement. We were particularly anxious to make this work as we felt it would be advantageous to measure the top level of medium where the separation was actually being made, but we were doomed to disappointment because it was impossible to keep the screen clean of float. Since the top gravity of the cone is the most convenient place to sample for control, a launder about 2 in. wide was installed longitudinally beneath the

Jan 1, 1951

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,' is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3' tests, however, this is not justified, and the D values

Jan 1, 1941

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. Development of the new units was prompted by a desire for solution of the following problems: 1—The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pct of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be pro- vided in the event that air lines were no longer available. 2—Drill performance has increased beyond the capacity of present 3-in. drifter machines. 3—The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4—Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5—Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6—In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1—It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1953

By M. A. Mayers, J. A. Thompson

In recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.l-14 Only in Russell's method" and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼-in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C, consisting of two annuli of 0.011-in. (o.a8-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By B. H. Sage, W. N. Lacey

The growing background of experimental information concerning the volumetric and phase behavior of binary and ternary hydrocarbon systems is used as the basis for a comparison of these systems with naturally occurring hydrocarbon mixtures under conditions representative of underground petroleum reservoirs. The qualitative and semiquantitative similarities and differences between the two types of systems are considered in reference to the possibilities and limitations of using experimental data on binary and ternary systems for predicting the volumetric and phase behavior of naturally occurring hydrocarbon mixtures of low molecular weight. The possible influence on such phase behavior of water, hydrogen sulphide, nitrogen, and components of relatively high molecular weight is discussed. INTRODUCTION During the past two decades much effort has been devoted to the study of the volumetric and phase behavior of pure paraffin hydrocarbons and of binary and ternary mixtures of these compounds. Many of these studies were carried out with the direct objective of utilizing a knowledge of the detailed characteristics of binary and ternary mixtures of the lighter paraffin hydrocarbons for predicting the behavior of more complex mixtures. The ability to make such predictions with accuracy would be of great value in petroleum production and refining. Although the behavior of the methane-propane system' served at one time as a qualitative illustration of the probable characteristics of the more complex hydrocarbon mixtures found in nature, it' fell far short of requirements for quantitative predictions. The present paper endeavors to indicate the relation of the more recently accumulated information concerning the behavior of binary and ternary hydrocarbons to this problem. In discussing binary and ternary systems as examples pointing toward the behavior of multi-component systems no effort is made to present new methods of predicting the characteristics of natural hydrocarbon mixtures. Preliminary proposals have been made elsewhere for the prediction of volumetric phase equilibrium and thermodynamic data for multicomponent mixtures, utilizing as a basis the behavior of binary and ternary systems. Numerous other proposals have been made. That based upon the concept of a pseudo-critical state" has proved to be of value to the petroleum industry. Concurrently with this study of binary and ternary systems investigations have been made of natural hydrocarbon systems. Of the many publications reporting such experimental information only a few examples will be mentioned. A number of studies of black oil and natural gas have been made and much attention has been directed to extended and detailed investigations of the behavior of fluids in condensate fieldS 16,17,18,19,20. This work has been supplemented by some studies of the separation of bitumen from natural hydrocarbon liquids The over-all behavior of such systems has been used in predicting the volumetric and phase behavior of naturally occurring mixtures This background of experimental and correlated information concerning the behavior of multicomponent hydrocarbon systems also permits a direct comparison of the characteristics of binary and ternary aliphatic systems with those materials produced from underground reservoirs. PRESENTATION OF DATA The primary limitation encountered in using binary and ternary aliphatic hydrocarbon mixtures as examples of the characteristics of the fluids encountered in underground reservoirs lies in the existing lack of knowledge of the quantitative effect upon behavior of the presence of several important constituents, notably hydrocarbons of high molecular weight, water, carbon dioxide, hydrogen sulphide, and nitrogen. The presence of substantial quantities of hydrocarbons of fairly high molecular weight serves to increase the complexity of the phase behavior of natural systems. No simple systems yet studied give adequate guidance in this regard. The influence of such materials of high molecular weight was indicated earlier",?' to an extent which serves to show that definite limitations now exist in the correlation of simple and complex systems. However, significant progress is being made in filling gaps in the information. For example, similarities in the behavior of fluids in condensate fields with that of binary and ternary systems are becoming more systematically evident. A few studies of the behavior of water in paraffin hydrocarbon systems have been made Results of investigations of mixtures of carbon dioxide and the lighter hydrocarbons also are available Limited work has been reported con-

Jan 1, 1949

By Bruce W. Gonser, Robert I. Jaffee

Recent work by the authors1 established the constitutional diagram of the gold-germanium system. Of particular interest in the simple euctectiferous system was the eutectic alloy at 12 per cent Ge, which melted at the very low temperature of 356°C and had an unusually fine eutectic structure. It was of interest to investigate the effect of third components on the melting point, microstructure, and strength of this alloy, and in this work the effect of copper is discussed rather completely, with less complete data on the effects of silver, platinum, nickel, and zinc. No reference in the literature has been found on ternary systems with gold-germanium. Materials and Alloying -4s in the work on the binary system, gold-germanium, the germanium used in this investigation was the cyanide-reduced, 99.9 per cent product, produced by the Eagle-Picher Co. Fine gold sheet from Handy and Harmon, pure platinum sheet from the American Platinum Works, copper magnet wire from Anaconda, nickel wire assaying 99.6 per cent Ni. and electrolytic zinc were used for alloying. To make the alloys, charges of the pure metals were put in a graphite crucible and melted in an atmosphere of pure hydrogen. The temperature was brought up to about I050 C, and the metal allowed to freeze in the crucible. Except with alloys containing zinc, melting losses were consistently less than a few milligrams. When zinc was a component, weight losses up to half the weight of the zinc present were incurred, and the alloy compositions were calculated by assuming the entire weight loss to be that of zinc. In all other cases the composition of the alloys could safely be taken as that of the charge. The ingots, as solidified, were segregated, the heavier primary phases being at the bottom and sides of the ingots and the lighter primary phases at the top, but by sectioning the entire ingot vertically for microscopic examination, this factor could be evaluated. Ingots for microscopic examination weighed one gram, and those for thermal analysis weighed three grams. Thermal Analysis In this work, the eutectic line composition and thermal arrests were desired, and, after microscopic exploration had established the position of the eutectic line at a given percentage of the third component, a thermal analysis was run at that composition. The method of thermal analysis used in the work on the binary Au-Ge system,' a method particularly well suited for a small quantity of material, was used in this work. Clearly defined arrests were obtained, although with some alloys containing platinum

Jan 1, 1946