Search Documents

By Leon Banks

THE- Missouri-Kansas Zinc Corpn., operating in the Waco district, 15 miles northwest of Joplin, Mo., owns large tailing piles made during milling operations of the years 1918-28 by the Butte-Kansas, Acme, and Barnsdall mining companies, whose holdings have been purchased and consolidated under, the ownership of the Missouri-Kansas Zinc Corpn. These tailings had been considered too low in value to be worth retreating by the ordinary methods. C. Erb Wuensch, consulting engineer of the Missouri-Kansas Zinc Corpn., noted the difference in the type of tailing from upper-level and lower-level ore. The latter contained hard lime chats. He also found that mill losses had been due to particles of blende on the corners or sides of the chats and to the existence of soft, porous, cellular, lime chats containing varying amounts of blende. He conceived the idea that a quick grind in rolls or ball mills might change the type of the material so that jigging could make a clean tailing for discard and a partly concentrated product sufficient in blende content to justify the expense of fine grinding in ball mills to free the mineral entirely. A laboratory was equipped with the necessary machines and the writers were assigned the problem of developing a method of retreating the tailings.

Jan 1, 1929

By H. M. Howe, E. C. Groesbeck

Fig. 1 shows a volute aging break which developed spontaneously in a hardened and tempered steel helmet between 19 and 38 days after it had been tested ballistically. A similar break, shown in Fig. 2, developed spontaneously in a similar helmet about 40 days after the ballistic testing. In this case the rupture occurred abruptly and with a loud report. The path of rupture in this second case, though much the less regular, is the more interesting of the two, in that it is an approximation to two parallel volutes centered at the point of impact of the projectile, just below D. Several weeks later, after the photograph for Fig. 1 was taken, a similar doubling of the volute crack occurred in this helmet, starting from the end of the eyelash crack near A and spreading thence to the left contra-clockwise for about 1/2 in. The negatives from which these pictures are made have not been touched up in any way, save writing the letters on them. In both cases the trajectory of the bullet was normal to the initial surface at the point of impact, and in both the helmet passed the ballistic test without detectable cracking, under a velocity of impact not far below that which usually causes perforation. The initial surface itself was very nearly spherical throughout the region covered by the break.

Jan 1, 1920

By G. E. Archie

THE usefulness of the electrical resistivity log in determining reservoir characteristics is governed largely by: (I) the accuracy with which the true resistivity of the formation can be determined; (2) the scope of detailed data concerning the relation of resistivity measurements to formation characteristics; (3) the available information concerning the conductivity of connate or formation waters; (4) the extent of geologic knowledge regarding probable changes in facies within given horizons, both vertically and laterally, particularly in relation to the resultant effect on the electrical properties of the reservoir. Simple examples are given in the following pages to illustrate the use of resistivity logs in the solution of some problems dealing with oil and gas reservoirs. From the available information, it is apparent that much care must be exercised in applying to more complicated cases the methods suggested. It should be remembered that the equations given are not precise and represent only approximate relationships. It is believed, however, that under favorable conditions their application falls within useful limits of accuracy.

Jan 1, 1942

By J. H. Canterford

The adsorption of uranium onto Wyoming bentonite was measured in carbonate media over the pH range 8 to 11. Uranium was removed from solution onto the solids by a rapid reaction, proposed to be adsorption of the anionic uranyl tricarbonato complex onto edges of the clay platelets, and a slow reaction that may be precipitation of a hydroxide. The changes in uranium content of the aqueous and solid phases of a uranium ore carbonate leach slurry were also measured as the slurry was progressively diluted. There was an increase in the uranium content of the solids as the pH of the suspension was lowered, as observed with the Wyoming bentonite. Results indicate the conditions that should be met with respect to pH control to prevent the problem of excessive uranium adsorption in the counter-current decantation washing circuit of a conventional leaching process, as well as in the leaching and restoration phases of carbonate solution mining.

Jan 1, 1985

Jan 4, 1953

I. PRESIDING OFFICERS. At all Business meetings of the Institute the President, or, in his absence, the Vice-President, or, in the absence of both of them, any other member of the Board of Directors to be chosen by the meeting, shall preside. At all other meetings of the Institute the President of the Council or, in his absence, one of the Vice-Presidents, if present, shall preside II. ORDER OF BUSINESS. At each Business meeting of the Institute the order of business shall be as follows 1. Reading of minutes of preceding meeting. 2 Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Election of Members of the Council. 7. Reports of Standing Committees. 8. Reports of Special Committees. 9. Special Orders 10. Miscellaneous business. This order of business may be changed by a vote of a majority of the Members and Associates present in person or by proxy. The usual parliamentary rules shall govern all meetings of the Institute except in cases otherwise provided by the Constitution or the By-Laws. At all sessions of the Institute other than business meetings, the order of proceedings and the time of adjournment, shall rest in the discretion of the presiding officer

Jan 1, 1923

By Boris J. Kochanowsky

In a mobile crushing unit system trucks are replaced by a conveyor, which results in a continuous, almost fully automated operation with all its attendant advantages. Because of new designs for large mobile crushing units that have been placed on the market, the use of these plants has increased significantly during the last three years. Gains in productivity and reductions in costs are vital to every mine operator, and the shovel-crusher-conveyor system is a powerful tool with which to achieve this goal. New Designs Increase Throughput While Reducing Size The basic concept of the shovel-crusher-conveyor scheme of operations is simple and sound, with the result that domestic operators are showing a growing interest in its application. A number of operators have been using small mobile crushing plants for several years, but large operators, in spite of considerable interest, have not been able to use this system because no mobile crusher capable of crushing 1000-2000 tph of rock loaded by a large shovel (6-12 cu yd) has been available. A suitable crusher must accept rock of the size handled by these large shovels, be simple in design, easily maneuverable, remotely controllable, and have price and maintenance costs not much higher than those for stationary crusher installations.

Jan 9, 1968

By Larry D. Hartzog

PANELISTS Paul Chamberlin, Nerco Minerals Jim Gourdie, Goldfield Mining Corp. Roger Leonard, Cyprus Northumberland Mining Co. Eric Daniels, Tenneco Minerals John Dasher, Consulting Metallurgist Bob Shoemaker, San Francisco Mining Associates Larry Hartzog, Bechtel Civil and Minerals, Inc.

Jan 1, 1984

By F. D. Rosi, Walter R. Hibbard, R. I. Herron, H. T. Clark, O&apos

Introduction and Previous Work In the search to find a copper-base alloy with high strength properties, it was considered that the addition of a small amount of an age-hardening element to a binary system with useful strength properties might result in a series of alloys of theeretical and practical importance. The copper-nickel system was selected for its basic properties and chromium was added as the age-hardening element in view of the small percentage involved and its decreasing solubility with decreasing temperature. A study of the Cu-Cr binary alloys was undertaken as a preliminary investigation. However, in view of the response of these alloys to heat treatment, the scope of this phase of the investigation was widened.

Jan 1, 1949

By H. A. Schwartz, A. F. Gorton, H. R. Payne

In a previous paper1 we published what we believed to be a correct stable equilibrium diagram for an iron-carbon alloy containing + 1.20 per cent. silicon. The purpose of the present paper is to record the results of studies concerning the effect of silicon on the location of the eutectoid points of both systems, including also certain incidental observations of general interest. We prepared white cast irons containing roughly 21/2 per cent. carbon, 0.05 per cent. manganese, and 0.03 per cent. each of phosphorus and sulfur, but of accurately known silicon contents which varied from 0.40 to 3.32 per cent. These were completely graphitized, and both A1 points determined, as in our previous work, the specimens being converted from the stable to the metastable condition and vice versa by appropriate heat treatments. Each stable alloy was heated to a few degrees above Arl for 3 to 7 hr., quenched and analyzed for total and graphitic carbon, the difference being the "combined" or, better, agraphitic2 carbon content of the saturated solid solution just above the eutectoid transformation. One specimen was lost through accident, and the 0.40-per cent. silicon material gave an anomalous result ascribed to difficulty in maintaining the stable system in the presence of but little silicon.

Jan 1, 1923

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.' The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By Edward C. Mack, Ronald G. Stovash

INTRODUCTION Ronald G. Stovash General Superintendent Consolidation Coal Company Shoemaker Mine Moundsville, West Virginia Consolidation Coal Company's Shoemaker Mine is located in West Virginia's Northern panhandle near Wheeling, adjacent to the Ohio River. Steam coal is mined from the Pittsburgh #8 seam which averages 65 in. in thickness. The 10 in. of draw rock directly above the coal is taken on advancement, but remains when longwalled. The top consists of up to 12 in. of lower quality coal, and immediately over that, up to 10 ft of multi layered shales, coal, and bone. The cover ranges from 300 to 800 ft of shales and limestone. Two longwalls operate in the mine. The first longwall started in April 1975 and is retreating its eighth panel. This wall was the first to use shield supports in the United States. The second longwall started in September 1979 and is currently retreating its first 7,000 ft panel.

Jan 1, 1981

Jan 1, 1879

Jan 1, 1894

By Keith Contor

The concept of using simulators to train operators of vehicles is not new. However, the Bureau of Mines initiated these programs to determine if computer controlled training devices would enhance production and improve safety in the coal mining industry. Two prototype devices have been constructed, tested and are currently operational. The continuous miner and dragline operator training systems both incorporate full scale operator stations using operational controls and displays. The operator interacts with the visual system through the cab controls to perform basic tasks and develop skills required for startup, operation and shutdown of the mining equipment. Data pertaining to the concepts and techniques applied during the design, development and evaluation of the training devices are presented. Descriptions of trainer designs and visual systems for training equipment are presented and the results of the system evaluation are summarized.

Jan 1, 1983

By Henry D. Hibbard

Henry D. HibbaRd, Pittsburgh, Pa,: This is a most interesting and instructive paper, some of whose lessons should find immediate application. It points out how fuel-consumption is to be decreased in open-hearth practice, by changes in the plan of the furnace. To look first at the greatest item of loss, radiation, it is seen that thicker brick-work is advisable to lessen this. Especially is this true of the roof, made at present, almost universally, only 9 inches thick to prevent cutting. Now that high roofs, well above the course of the flame, are becoming general, and the average melter is better able to judge the temperature of his furnace, that reason has less force; and we may build roofs 18 inches thick, or perhaps better cover the usual 9 inches with an equivalent layer of sand, which has the advantage of following the arch as it rises and falls with the different degrees of heat. The side-walls of the hearth, usually 131/2 inches thick, may also he thickened up to 18 inches, and the door-linings to 7 inches; and the heat thereby saved will be valuable, while its absence from the working-platform will be much appreciated by the workmen.

Jan 1, 1892

By S. R. Smith, W. M. Voorhis, J. D. Young

The Tennessee Valley Authority (TVA) has conducted investigations to identify the major causes of coal pile inventory adjustments. This paper describes past and current attempts to improve inventory survey accuracy and reduce costly inventory adjustments. The unique interaction between accountants and engineers is also reviewed. Data and results of a recent field test wing downward-looking radar developed by Ohio State University are presented. These show great promise in determining coal pile depth and density, thus improving inventory accuracy. This electromagnetic remote sensing technique, if successful, would provide an optimum technical and economic method of surveying all 12 TVA stockpiles without costly borehole drilling or disrupting stockout and reclaim activity. The effect of changing coal quality to meet environmental standards has made accurate coal pile density measurement more important than ever in reducing the costs of electric power generation from coal.

Jan 1, 1984

A week-long educational program and two-day symposium on applying the fluidizing reactor to the minerals industry drew more than 100 engineers to the University of Arizona at Tucson several weeks ago. The educational program, intended for engineers who will work closely with the reactor, attracted registrants from all sections of the U. S. and Canada. Meeting at the College of Mines on February 23 for a full week of intensive classwork, the engineers ploughed in with enthusiasm. Eight hours daily of lectures and laboratory work were followed by a generous helping of homework supplied by Professor Sigmund L. Smith, who directed the course. The study program was completed on Friday and the following Monday marked the start of a symposium of technical papers covering a wide variety of operations and new ideas.

Jan 4, 1959

By Tony B. Szwilski

The paper outlines the parameters required for an estimation of the size of chain pillars for longwall coal mining. The principal parameters are: stress distribution around the edge of the extracted coal panel, strength properties and geometry of the pillars. The principal thrust of the paper is directed toward correlating the chain pillar strength to the magnitude and direction of strata load expected to act on the pillars. A brief review of the pillar strength formulae pertinent to chain pillar stability is given. The chain pillars are categorized as 'yielding' or 'stiff', depending on the duty required of them. The coal measure strata is classified as 'soft' or 'hard' conditions, the degree of competence of the roof and floor greatly influencing the caving characteristics of the gob and the stability of the roof chain pillars.

Jan 1, 1983

By Walter von der Linden

A description is presented of the mining conditions of four longwall shield type support installations in the Pittsburgh seam in northern West Virginia and southwestern Pennsylvania. Details of roof control and operating procedures, production and performance data, and equipment description and basic engineering specifications are given for these four longwall installations. The range of mining heights was between 150 and 250 cm (60 and 95 in.). The major accomplishment of the shield supports in all four faces was the provision of an almost 100% availability for coal cutting; i.e., the face-down time due to roof control problems and support maintenance requirements was minimal.

Jan 1, 1978