Search Documents

By Douglas Muir, Chas. A. Chase

The Aztec mine is not widely known, by reason of its isolation and the relative insignificance of its tonnage; financially, however, it has an enviable record and geologically it is extremely interesting. The town of Baldy, Colfax County, the mine camp, at an elevation of 10,000 ft. (3048 m.) is 8 mi. west of Ute Park, the terminus of a branch of the A. T. & S. I?. Ry. The mining tract was designated by the Maxwell Land Grant Co. as the Aztec Reservation, and lies on the east slope of Mt. Baldy, the summit of which, 12,491 ft. (3807 m.), is one of the highest in the state. Rich copper float was found on the northeast slope of the mountain in 1865, and discovery work was begun the next year. At the same time, gold placers were found on Willow Creek, on the southwest side of the mountain, and the Elizabethtown settlement followed shortly. Gold washing lasted many years. In 1867, placer gold was found also on Ute Creek, the tracing of which to its source led to the locating of the Aztec mine by Lynch, Dogherty, and Fosley in the following year. The early production came from the contact of shale and sandstone or from sandstone immediately above the contact. Exact record of production is lacking, but L. C. Gratonl gives estimates ranging between $1,250,000 and $1,500,000, of which about $1,000,000 was taken out in the first four years. After the exhaustion of the early bonanza, production continued intermittently until 1909, when the Maxwell Land Grant Co, undertook systematic development, through four adits at intervals of 75 ft. vertically or approximately 100 ft. on the dip of the contact, which was thought to contain generally a quartz-pyrite vein. The two intermediate adit? almost immediately reached ore, the most southeasterly in Fig. 2. This ore, however, was not mined until 1911-12; its grade was about $20 and

Jan 1, 1923

By George Otis Smith

In the utilization of natural resources owner, operator, and consumer* should share the attendant benefits. Development needs to be planned under terms recognizing fully the interests of all concerned, for ally undue advantage given to any one of these participants is apt to involve even greater and disproportionate injury to one or both of the others. For this reason it is well to preface any consideration of needed reforms in legislation affecting the disposition of public land with a survey of certain fundamental principles that determine the general conditions of a11 land transfers preliminary to development, utilization, and production. The disposition of any undeveloped natural resource, whether timber, oil, coal, or water power, as a transaction to which land owner and prospective developer are parties, must be based in theory upon a division of expected returns.' Whatever the terms of such disposition, neither party can reasonably ask for anything other than an equitable division of the returns. Under this analysis three and only three questions need to be discussed; namely, what are those profits, how is this division to be accomplished, and what is the equitable basis of division ? The answer to the third question should probably be found by applying to the problem the principles of theoretical sociology, and the question need not be mentioned further at this time, inasmuch as it does not involve the practical considerations to be kept in mind in connection with the other questions, which are concerned with only the measure of returns and their division. That is to say, whether the land owner's equity is to be stated as 95 per cent, ox as 6 per cent, of the profits attending the development of the particular resource, no change would be necessary in the method to be adopted of arriving at the closest approximation of the prospective total profit. If on this basis we now compare the two methods of disposing of

Jan 1, 1915

By Arthur Dwight

WE NOT have to go so very far back, when measured in actual years, to what may be considered the beginning of the industrial era of the great West, the discovery of gold in California in 1848, just 74 years ago. By a strange coincidence, this event occurred within a few days of the signing of the treaty with Mexico which ceded California to the United States. Needless to describe the mighty wave of humanity that hurled itself toward the setting sun in response to that call. The single thought in every one's mind was gold. The gold as they found it in placers or ledges could be so easily worked, and the product was so readily transportable, and available immediately as money, that practically no attention was paid to deposits of the base metals, in the treatment of which cheap transportation was a paramount con-sideration; consequently little progress was made in anything but gold mining until after the Civil War. The next great step was accomplished when East and West were united by the successful construction of the Union Pacific Railroad from Omaha across the great plains and through the Rockies to meet the rails of the Central Pacific coming eastward across the Sierras. The industrial history of our great West really dates from the day when those two hands of steel were joined, on the shores of the Great Salt Lake at Prom-ontory Point,. May 10, 1869. That seems a long time ago when we think of the enormous changes that have been wrought since that day, and when we regard the rich empire that has sprung up in that western land. Into the new empire thus made accessible, by this first thread of steam transportation, flocked a new brood of adventurous spirits from the older communities of the East. This way walked Fate; and as she, went, flung far the line of destiny, That bound an untracked continent to brotherhood from sea to sea; That long gray trail of dream and hope, marked mile by mile with graves that keep On every barren hill and slope some stout heart lost in dreamless sleep. Patience and faith and fortitude were willed to it and justified; Stern, homely virtues, plain and rude, eternal as the sky and wide. Nor ever sea-king dared the sea in sterner mood than these who went Strong armed to wrest from Mystery their birthright, half a continent.

Jan 4, 1922

By B. G. Zambre, G. A. Parks, J. N. Roco

Automatic controls have long been a fact of technological life. Some understanding of control systems is rapidly becoming essential to the competence of mineral engineers. Students in undergraduate mineral engineering curricula, however, should not be expected to develop proficiency in the design and interpretation of control systems. They should be provided the opportunity to absorb some of the fundamental concepts and cant of such highly specialized peripheral fields as automatic controls. The present paper describes the components of a simple, flexible and relatively inexpensive control system designed primarily for the use of students in independent study projects. The control system is based on a continuous on-stream optical analyzer analogous to commercially available systems using X-Ray fluorescence analysis. The components can be easily adapted to control other separators and separations. As described here, they have been arranged to control the magnetic separation of a magnetite bearing specular hematite from quartz to produce a quartz product of fixed hematite content using a minimum of power. The control system consists of the magnetic separator* with a vibrating feeder, † a sampler, an optical scanner, a differential amplifier, a millivolt recorder ‡ and a motor driven, metered variable DC power supply for the separator electromagnet. An optional magnet current recorder is useful. The system as arranged for closed loop control is illustrated in Fig. 1. The elements of the loop are identified in automatic control jargon in Table I. The same components can be easily adapted for use in other control modes.§.1 * A Carpco Induced Roll High Intensity Magnetic Separator (Carpco Manufacturing, Inc., Jacksonville, Fla.); modified for external magnet power supply. A Jeffrey-Traylor Vibrating Feeder Type 1B (Jeffrey Manufacturing Co., Columbus, 0.). A Beckman Laboratory Potentiometric Recorder (Beckman Instruments, Inc., 619-A) fitted with adjustable limit switches for external circuit control (Beckman Instruments, Inc.. 71980). Terminology is taken from ref. 1. CLOSED LOOP OPERATION The separation is monitored through the optical reflectivity of the tailings stream which is proportional to the hematite content, THA. The difference, A, between the measured analysis (actually a proportional voltage) and a reference analysis (also a proportional voltage) is continuously recorded. The separation is controlled through changes in the electromagnet current, I, supplied from a motor driven variable source. The two primary variables, ? and I, are linked through adjustable limit switches on the

Jan 1, 1965

By C. W. Hill

FLUXES, in general, may be classified according to their use as soldering, foundry or casting, and metallurgical and the chemistry of their action follows quite closely this division. The term foundry or casting fluxes, as used here, refers to the substances added to molten metals, preparatory to casting into molds or ingots, with the object of removing small amounts of impurities that have been introduced in handling or melting the metal, which was placed in a fair state of purity by the previous refining or metallurgical processes. The sources of these impurities are the oxide coating on the surface of the ingots, material extracted or mechanically removed from the crucible or furnace wall, and those formed by the reaction of the molten metal with the heating gases or furnace atmosphere. As commonly used, the term fluxes is applied to such materials as ammonium chloride, zinc chloride, salt, borax, and boric oxide. A second class of materials, usually called deoxidizers, includes substances, such as metallic phosphides, sub-oxides, carbides, and bo-rides, that reduce the metallic oxides present in the metal. A third class includes various compounds that are molten and non-volatile at the temperature of the molten metal and are used primarily to protect the surface of the metal from the action of the furnace or exterior atmosphere; to this class belong such mixtures as lime and fluorspar, lime and soda ash, various minerals, etc. In some cases these protective layers may act in a manner similar to the metallurgical fluxes and dissolve or unite with the oxide impurities of the metal, but as generally employed this latter action is negligible since there is little opportunity for the coverings to come into contact with more than the surface of the metal, and hence they are without action on the body of the molten mass. The use of fluxes is the result of factory experience and tradition, but an extensive study has not been made of the chemical, and physical actions that occur or the effects of these actions on the properties of the metal. It would seem necessary in any successful study of metal fluxes

Jan 10, 1920

By H. C. Otis

DURING the past year or two considerable time and money have been spent in developing equipment for tubing large-volume high-pressure oil and gas wells without loss of production. That the efforts have met with success is proved by the fact that any properly cased well, regardless of its production or regardless of its rock pressure or working pressure, can now be safely tubed with no appreciable loss of production, provided experienced crews handle the new equipment. It is conceded that a far better gas-oil ratio can be secured by flowing a well through tubing of a proper diameter-the diameter of the tubing depending, of course, upon the volume of fluid and gas and the depth of the well-than by the more usual method of installing a choke at the mouth of the well. Where possible it is becoming the practice to bring wells in through tubing, though in the majority of instances this is not feasible. In many instances it has developed, after a well has been brought in through tubing, that the tubing installed is either too large or too small for the most efficient operation or that the well had not been drilled deep enough. The equipment described in this paper, in the hands of experienced men, permits the tubing of these wells after they have been brought in, with the size of tubing then determined by actual observation to be best suited for each particular well, and with no danger of the well getting out of control, of catching fire, of drilling itself deeper, or of any loss of production. The deeper the flowing production with the consequent future higher lifting costs, the more essential it is that the size of tubing used be such as to give the best possible gas-oil ratio. The ability to bring in these deep wells through the casing and then, immediately after their completion, regardless of volume or pressure, to tube them with the size of tubing that permits the most efficient use of the gas present will doubtless save many dollars.

Jan 1, 1929

By Harold L. Hinds

The Homestake Ledge or Lead was discovered by Fred and Moses Manuel on April 9, 1876. They recovered a small amount of gold from the quartz outcrop, but, unfortunately, they were prospectors not hardrock miners. Their claim was sold to a group of experienced California mining men in 1877. These mining men incorporated their holdings as the Homestake Mining Company. This was the beginning of one of the greater gold mining enterprises of the Western World. Metallurgical operations progressed over the years from an eighty- stamp grinding circuit using amalgamation for recovery to the more complex circuit of today. The Homestake Mine, today, is an underground mine with the deepest winze reaching the 8,000-foot level. The ore is hoisted to the surface by two primary shafts, the Ross Shaft and the Yates Shaft. See Figures 1 and 2. It is crushed in three-stage crushing plants located in the headframes. From here, it is trammed to the mill fine- ore bins by electric locomotives. The Lead grinding plant milling circuit, known as the South Mill, receives ore from the crushing plant at minus 112 inch (Figure 3). This material is dumped into overhead fine-ore bins from five- ton rail cars. The fine-ore bins have a live capacity of about 3,700 tons. The South Mill bins can also be fed by a conveyor system which reclaims ore from an 80,000-ton capacity stockpile. This stockpile is built up from peak mining production periods and available surface low grade material. It is then reclaimed during low mine production periods. The grinding circuit at the South Mill consists of four rod mills in open circuit followed by four ball mills in closed circuit. Three of the rod mills are 6-foot by 12-foot Marcy's. The other is

Jan 1, 1983

By Kefton Teague

The minerals discussed in this section have experienced a gradual, although not spectacular, growth in general. Obvious exceptions are the gradual decreasing use of talc and bentonite as filler materials, partly because of availability and relatively lower sales price of competitive materials. Mineral fillers and filter minerals are used principally in those countries that are heavily industrialized. Except for diatomaceous earth of filter grade, most industrialized countries are reasonably self-sufficient in the various filler and filter minerals. Prices of the various mineral commodities during the period 1950-1970 increased approximately as follows: barite, 43%; diatomaceous earth (filler), 49%; diatomaceous earth (filter), 55%; fuller's earth, 55%; talc. 77%; and bentonite, 94%. Actual usage of these mineral commodities as fillers and filters, during this period, showed changes approximately as follows: (1) Decrease-fuller's earth, 6%; talc, 15%; and bentonite, 29%. (2) Increase-barite, 113%; diatomaceous earth (filler), 150%; and diatomaceous earth (filter), -194%. A relationship between the amount of the various fillers and filters used and price increases is apparent. For example, barite increased only 43% in price, but its use as a filler has increased by 113%. On the other hand, talc, which increased 77% in price, decreased in filler use by 15%; and bentonite, which increased 94% in price, has decreased for filler and filter purposes by 29%. The actual decrease in the use of some of these commodities is not entirely caused by an increase in price. Competitive materials frequently have made substantial gains in the various filler and filter markets. For example, much of the bentonite used in the late 1940s and early 1950s for clarification of mineral and vegetable oils has been replaced by competitive materials. BARITE Occurrences and Sources In the United States, barite is produced from about 14 states, listed in approximate order of importance as follows: Missouri, Arkansas, Nevada, Georgia, Alaska, Tennessee, Kentucky, California, New Mexico, North Carolina, Washington, Idaho, South Carolina, Texas, and others. During the 20 years ending in 1970, almost equal amounts of barite were produced from Arkansas and Missouri. Within recent years, Nevada has replaced Georgia as the third leading barite--producing state. West Germany is second to the United States in barite production. Other important barite-producing countries include: Mexico, USSR, Italy, Greece, Canada, and Ireland. Ireland has become an important barite producer only recently. Barite is obtained from vein and cavity fill-

Jan 1, 1976

By Günter Petzow, Siegfried Steeb

DURING an investigation of the U-Co-A1, U-Ir-A1, and U-Ni-A1 ternary systems, three previously unknown phases have been identified which correspond to the phases UCoA1, UIrA1, and UNiA1, and which be- long to the C22 (Fe2P) type (P 6 2m). In the following the structure determination of the new ternary phases is reported. The alloys have been prepared in an arc furnace under purified argon from 99.97 wt pct U, 99.83 wt pct Co, 99.99 wt pct Al, 99.95 wt pct Ni, and 99.97 wt pct Ir. The pellets obtained were bright and brittle; chemical analyses agreed with the nominal compositions. To obtain equilibrium, the samples were annealed in evacuated quartz capsules at 950°C for 30 hr and then quenched in water. Guinier photographs were processed and evaluated according to a method already described previously.1,2 The hkl's, measured and calculated sin2 6 values, and in the case of UCoAl only calculated and estimated intensities, are given in Tables I to 111. Lattice parameters refined according to the least-squares method and the respective mean-square variations are presented in Table IV. Lattice parameters, especially the c/a ratio, lead to the assumption that the three phases are crystallizing in the C22-type structure. For the calculation of the intensities given in Table I, the atomic positions recently reported by wyckoff3 have been accepted for the C22 (Fe2P) type. The uranium atoms were assumed to be in phosphorus sites; furthermore the scattering amplitudes of the boron atoms have been averaged in the stoichiometric formula UB2 according to atomic percentages; i.e., for these atoms a statistical distribution on the iron sites was assumed. The two smallest distances between a uranium and

Jan 1, 1967

By E. L. Bruce

GOLD occurs ill many mineral deposits in the rocks of the Canadian Shield. It is present in the ores of many base metals and a considerable quantity is recovered as a by-product from the production of copper at Noranda, of nickel and copper at Sudbury and of copper and zinc at Flinflon. But the greater part of the gold production of Canada is from deposits in which gold is the only metal of value. No gold is obtained from placer deposits within the borders of the Canadian Shield. A brief review of the geological relations of some of the gold deposits of the Canadian Shield will be presented in an attempt to explain certain associations. Only those which are being worked for their gold content will be considered and descriptions will be confined to representative types of deposits, chiefly those of major importance; a few others, differing in certain features from those of the older and larger mines, will be included in order to illustrate the general conditions in which gold occurs in these ancient rocks. Brief summaries will be given of the geological relations of the Beattie and Siscoe mines of northern Quebec, of the mines of the Porcupine and Kirkland Lake areas of northeastern Ontario and of the Howey, Central Patricia and Little Long Lac mines of northwestern Ontario. Genetic relations to igneous rocks of granitic composition, outcropping in the vicinity, have been assumed for many of these deposits. Undoubtedly the ore minerals have been derived from igneous sources and, for some occurrences, there is evidence suggestive of genetic relationship between the ore bodies and neighbouring intrusive rocks. During the past few years, however, many investigators have expressed doubt of the genetic relationship of certain ore bodies to igneous masses near which they occur. As will be seen from references in the following descriptions the importance of the structural conditions in localizing deposition has been realized. This is pointed out for Canadian pre-Cambrian gold deposits by E. T. Dougherty, who also refers to the

Jan 1, 1937

By W. J. Keep

Some explanation of methods of testing will be given before presenting the record of a series of physical tests of aluminum, other metals and alloys. I. The Methods Employed and Meaning of Diagrams. The test-bars used, 12 inches long and 4 inch square, are cast in green sand, with chills bedded in such a way that the ends of the bar run against them. By splitting the ends of the bar the depth of chill can be measured. The chills being held in the mould 121/8 inches apart, the space between the end of the bar and the face of the chill, after both are alike cold, is the amount of shrinkage, and is recorded in thousandths of an inch per foot.

Jan 1, 1890

By M. Gensamer

IN applied mechanics and in metallurgy the transition from elastic to inelastic action is a matter of considerable interest and importance. Often the first inelastic deformation is apparently quite homogeneous; that is, uniformly distributed throughout the specimen. Sometimes this deformation is heterogeneous; that is, localized; inelastic deformation proceeds to some definite amount in restricted regions before adjacent regions of the specimen are inelastically deformed. In such cases the deformation does not become homogeneous until the whole specimen has been deformed the amount corresponding to that for each localized deformation. If the test is stopped before uniform extension sets in, the heterogeneous character of the deformation is apparent on the surface of the specimen through characteristic markings, which have been called "Lüders"' lines, "Hartmann's" lines, the "Piobert effect," or simply "flow figures." These markings are the source of considerable trouble in fabricating operations, particularly in the deep drawing of steel sheet. In many cases where the transition is of this nature, the stress developed at the upper limit of the elastic range is greater than the stress during the period of heterogeneous deformation, giving rise to the familiar "drop of the beam" effect in testing. The amount of the yield-point elongation, as well as the value of the stress at the lower yield point (the value to which the stress drops when yielding begins), are functions of the temperature and the testing speed. Lower temperatures and faster rates of testing increase both the yield-point elongation and the yield-point stress. These matters have been ably discussed in a recent paper by Winlock and Leiter1 though, as brought out by the discussion of that paper, the phenomena are but little understood. The purpose of the present paper is to clarify the problem through the application of a simple principle, and to show that, through the application of this principle, a number of phenomena in the plastic deformation of metals become more readily understood. The principle is this: During homogeneous flow, the rate of work-hardening is greater than the rate of change of stress resulting from change

Jan 1, 1938

By E. Lancaster-Jones

THE gravity magnitudes obtained by means of observations with the Eötvös balance in the field are necessarily resultant or total effects due to all abnormalities of mass distribution, including even the effects due to the ellipticity and rotational motion of the whole earth. Since the object of the survey is to isolate the effects which arise solely from some particular subterranean feature, and to deduce therefrom the configuration and extent of this feature, the first step is to eliminate from the observed effects all those due to "disturbing" (i. e., unwanted) features, whether above or below the surface of the ground. The disturbing features have different characteristics, according to their situation relative to the center of the balance and to the horizontal plane through the foot of the balance, or station point; this diversity was recognized by Eötvös, who divided the total effects into so-called Normal, Terrain, Topographical, Cartographical and Subterranean effects. This classification has been adhered to by most subsequent investigators, but the writer prefers to employ the term "three-dimensional," which really indicates the essential character of the class of effect known as "Subterranean," at any rate from the standpoint of the computer of effects. Before disturbing effects can be eliminated, the features must be measured up or surveyed, whether by topographical, mining, or boring methods, and then the effects of each feature calculated and subtracted from the total observed effects. After this the problem of interpreting the residual effects will itself necessitate the computation of the assumed feature, or even a series of trial features.

Jan 1, 1928

By Lachlan Gilchrist

MEASUREMENTS of resistivity by methods involving the use of two current electrodes and two potential electrodes in general collinear with the current electrodes have been made extensively in geophysical investigations. In the method developed by Wenner and made use of by Gish and Rooney, and later in a modified form by Lee, the distance between the current electrodes is divided into three equal parts by the potential electrodes. In one of the methods developed by Schlumberger prospecting methods and by Koenigsberger, one current electrode is placed at considerable distance from the other and potential measurements are made in the immediate neighborhood of one of the current electrodes. The method is described as the single current electrode method, and the effect of the distant current electrode is considered negligible or a correction is made for the effect in the calculation of the resistivity. Usually the correction that is introduced is based on the calculated effect for measurements made in a homogeneous conducting material. The useful application of these methods in prospecting for minerals, of course, is in regions where nonhomogeneous conditions exist. In many of these conditions it is very doubtful whether the effect of the distant current electrode may be neglected, except for measurements in the immediate neighborhood of the "single" current electrode, and corrections based on homogeneity of the medium will necessarily be inadequate. In order to obtain a degree of symmetry that would preclude the necessity for corrections for the distant electrode and that would simplify interpretation, it appeared desirable to use a central current electrode and a set of distant end current electrodes symmetrically placed about the central electrode as shown in Fig. 1 and to provide by means of auxiliary resistances that the currents passing into the earth at the distant end electrodes should be equal. Circumstances did not permit the operation of this plan in complete detail but a degree of symmetry was obtained by using a central current electrode and two distant collinear end current electrodes and by taking measurements along a line passing through

Jan 1, 1931

By Howard Eavenson

ONE who has been trained in belief in the law of supply and demand and its effect upon prices finds it difficult to adjust himself to the minute regulations imposed by the New Deal, and also to the bewildering changes of government policy as expressed within a short period of time between the antitrust laws and the N.R.A., and later by the Bituminous Coal Conservation Act of 1935. A survey of the coal industry since the World War, both in this country and Great Britain, however, shows that regula-tion of some sort is needed if any stabilization is to be achieved and if the Wage structure and economic welfare of the many communities dependent solely upon coal are to be maintained. Let us look at what has happened to the industry since 1920, which can be considered as the end of the period affected by the war influence. This discussion will be confined solely to bituminous coal, although many of the general conditions are equally applicable to anthracite, the position of which now is at least as bad as that of the softer variety. Since 1920-to the end of 1934-the production of coal has decreased from 568.7 million to 358.4 million tons, or 37 per cent; the number of mines from 14,766 to 6,258, or 58 per cent; the average annual production per mine has changed from 38,512 to 57,425 tons, or 50 per cent. The number of large mines has increased considerably, and the number of men employed has decreased from 639,547 to 458,011, a reduction of 28 per cent, while the average output per employee has changed from 4.0 to 4.4 tons, or an increase of 10 per cent. The average price per ton of coal at the mine has varied from $3.75 to $1.75. During that time wages decreased largely until 1933 and since that time have increased, until now the rates paid are- considerably above those in other occupations, although the actual yearly earnings are low, because of part-time work. From 1920 to the signing of the Jacksonville wage agreement in 1924, about two-thirds of the men were union members and practically all of the nonunion mines were south of the Ohio River; with the fixing., of the high wage scale of that agreement, which soon proved to be an uneco-nomic one, many of the mines found that they could not retain their business, so gradually changed to nonunion. By 1928 the proportion

Jan 1, 1936

By E. S. Bardwell, R. J. Lapee

Twenty years ago, W. T. Burns, in his paper presented at the Butte Meeting of the Institute,' discussed the general scheme then in use in the electrolytic copper refinery of the Anaconda Copper Mining Co. at Great Falls, Mont., for removing impurities from tank-room electrolyte and controlling its acid content. Since then marked changes have taken place in copper-refinery practice at Great Falls. The electrolytic copper refinery in use in 1913 has been replaced by a new and entirely modern plant capable of producing up to 27,000,000 Ib. of cathode copper per month. With the building of the new plant in 1916, the treatment of converter anodes was discontinued. At first the substitution of refined anodes for converter anodes resulted in a decrease in the impurity content of the anodes, but as time went on, changes in metallurgical practices at the smelter resulted in substantial increases in the impurity content of the anodes. The leaching of the silver slime to remove copper before shipment to Raritan for treatment further added to the purification problem. The fact that the scheme of purifying electrolyte which Mr. Burns described in his paper has proved adequate for our needs under a wide variation of conditions speaks well for its essential soundness. Method of Purification Briefly, the method adopted for purifying tank-room electrolyte at Great Falls has been as follows: Each day a certain volume of tank-room electrolyte is run off and sent to the purification plant, where it is boiled down to approximately 46' 136. The concentrated electrolyte is then sent to crystallizing tanks where the bulk of the copper is crystallized out as copper sulfate. The mother liquor is then passed through insoluble anode tanks to remove the last of the copper and most of the arsenic and antimony. It is then either returned to the tank room direct or boiled down to 55' Bé, the iron and nickel salts crystallized out and the mother liquor returned to the tank-room circuit as restored acid. Prior to 1930 all of the evaporating was done in lead-lined tanks 13 ft. in diameter by 4.5 ft. deep, provided with lead heating coils through which steam at 30 lb. gage pressure was circulated.

Jan 1, 1934

By C. H. Jr. Herty

IRON oxide .(Fe0) plays an extremely important part in the manufacture of steel. In the open-hearth furnace and the Bessemer converter it is the chemically predominant compound and controls to a large extent both the operation of the furnaces and the composition and quality of their products. Almost all of the refining action is carried out through the medium of FeO, which oxidizes carbon, manganese, silicon, and phosphorus. At the end of any open-hearth or Bessemer heat the steel contains dissolved iron oxide, which must be wholly or partly eliminated. The type of deoxidation product depends on the amount of dissolved iron oxide and on the deoxidizer used. After the heat has been deoxidized and while it is being teemed, iron oxide diffuses from the ladle slag into the metal, causing losses of deoxidizer and increase in iron oxide content of the steel. It is generally believed that non-metallic inclusions are responsible for a great many failures of steel in service and for decreased yield of steel during rolling. The basis of most non-metallic inclusions is dissolved iron oxide. This investigation was undertaken in order to determine the amount of iron oxide that will dissolve in iron under various conditions. Steel-making slags are complex and it has been thought best to determine solubility under simple slags as a first step. The study is being continued under slags whose compositions approach those of operating. slags.

Jan 1, 1928

By John F. Blandy

Every new mining district has had its own peculiar experiences in inventing and experimenting upon new methods for the various operations of mining, and more particularly in the processes of crushing and dressing ores. As a matter of course, during this period many old things have been reinvented, patented, and cast aside, there to remain until at a future day other geniuses shall bring them forth again as new. In this respect the Copper Region of Michigan has not been behind other mining centres, and probably in no other part of the country has more money been expended in devising new machines and improvements upon old ones for the crushing of the rock. The appliances for washing the sand have not been so varied, simply for the reason that, having but one mineral, or rather metal, of high specific gravity to separate from rock material which varies but little in its character in any one mine, it requires much less care than is necessary in most mining centres of the world. At the beginning of operations in that district most of the work was in the control of Cornish miners, who introduced the simplest of Cornish mills, namely, wooden stem pestles, with wooden shafts and cams. These were well suited to the small mines, and particularly to the limited means of transporting more expensive machinery. As these facilities improved, they were enabled to change to iron, and to vary their patterns of rods, shafts, cams, and mortars. The most approved pattern, finally obtained, is the square or round stem, with collar adjustable by means of keys. In its present form it is a bar of cold rolled shafting, an eye in the top, an adjustable collar with key-plate and keys, the head and a shoe of chilled iron. The stem is fitted into the head by a slight taper. The battery has heretofore been of wood, lined with chilled cast plates, and bed-plate of the same, but within the past year the California pattern has been introduced. The screens are of sheet-steel, drilled with 16 holes to the inch. During this period of trial and gradual improvement in the pestle stamps, in the years 1855-6, the Ball steam-stamps were introduced, and after years of labor and expense, have been made the most efficient and powerful machines ever yet used for the purpose. It is ostensibly the Nasmyth steam-hammer, and yet the

EDUCATION for the mineral industry was at first a single comprehensive curriculum, but it was early recognized that the main basis of mining is physics, while that of metallurgy is chemistry. The first school to offer curricula leading to degrees in mineral industry education in the United States (1853) had separate ones in mining and metallurgy. The Columbia School of Mines (the fist really successful one) had only a single curriculum when it opened in 1864, but within a few years had so reorganized its work that it offered curricula in mining, metallurgy, geology, chemistry, and civil engineering. Interest in the metallurgy or geology curricula was slight at fist, and for the next 30 years the great majority of Columbia students took the mining curriculum, probably partly because it contained nearly as much geology as the geology curriculum, practically all the metallurgy, and most of the chemistry, and partly because of the degree awarded for it. Other schools kept their mining curricula equally broad, and as late as 1900-1910 men were graduating as mining engineers who were practically as well prepared to make geology or metallurgy their life work as they were for mining. Gradually, however, the subject matter of mining geology and metallurgy became so enriched through research and development that separate curricula in them became worth while; their progressive development is the subject of another chapter. Mining curricula also began to be somewhat diversified, and schools in areas where coal mining was of outstanding importance began to offer options in coal mining, the earlier curricula having been chiefly aimed at metal mining. The petroleum industry began its meteoric rise about the same time as mineral instruction in this country, but little more of applied science attended its birth than had attended such ancient practical arts as copper and iron

Jan 1, 1941

By Lombard Squires, W. K. Lewis, W. I. Thompson

The authors presented an article2† last year on colloidal properties of clay suspensions in which they attempted to sustain the position that the behavior of clay suspensions is due primarily to the mechanical interference of the platy particles, the nature and extent of the interference being profoundly influenced by the character of the surfaces of the particles, which in turn is determined primarily by the nature and amount of adsorbed foreign materials held on the surface of the particles by forces which are predominantly chemical in type. The following discussion is a continuation of that article to extend these same interpretative points of view to the behavior of clay gels. Insight into the mechanism of gelation is certainly of outstanding importance in the handling of drilling muds. In the former article it was suggested that the thin, flat plates that constitute the ultimate clay particles may build up aggregates by the overlapping of the ultimate plates face to face much longer and perhaps also much wider than the ultimate plates themselves, but not appreciably thicker. Exhaustive microscopic examinations of characteristic clays show no tendency for the larger particles, clearly visible under the microscope, to orient themselves in this way. It is true that the gelation of the clays is due primarily to the smallest particles, unresolvable other than by the ultramicroscope, so that the possibility of the deve1opment by them of an overlapping structure is not excluded. Furthermore, as one approaches the limit of resolving power of the microscope, the difficulty of observing accurately the shapes and relative positions of particles incresses excessively. However, in the absence of any observable tendency toward overlapping orientation of the large, visible particles, one hesitates to ascribe such a tendency to the smaller particles beyond the range of visibility. Should it develop that one must exclude the assumption of overlapping orientation, the explanations offered in the previous article are changed in only one respect; namely, one would now have to assume that the ultimate particles themselves have length, and probably also width, very large in comparison with their thickness.

Jan 1, 1936