Search Documents

By D. J. McAdam, R. W. Mebs

The technical cohesive strength of a metal means, not the interatomic forces, but the technically estimated resistance to fracture. An example of such resistance to fracture is the so-called "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture. According to the prevalent view,8 the technical cohesive strength of a metal. in any particular state as regards prior mecharlical treatment and heat-treatment, is determined by a limiting value of the algebraically greatest principal stress. In two previous papers by one of the authors, evidence was presented to indicate that the technical cohesive strength of a metal cannot be represented by a single stress value, but that it comprises an infinite number of values corresponding to the infinite number of possible combinations of the principal stresses. The technical cohesive strength thus comprises an infinite number of technical cohesion Limits, each representing a specific stress combination at fracture. In the same papers, evidence was presented that plastic extension causes a continuous increase in the technical cohesive strength. Such a variation is not in accordance with the prevalent view that plastic extension first increases, then decreases, the technical cohesive strength.' In this paper, as in the previous papers,14.15 the algebraically greatest principal stress will be designated S1, the least principal stress will be designated 33, and the intermediate principal stress will be designated S². The technical cohesion limit under polarsymmetric tension (S1 = S2 = S3) will be termed the "disruptive stress," and the cohesion limit under unidirectional tension (S2 and S3 = o) will be termed the "severing stress."l4, .l5 The yield strength of a metal, according to the generally accepted theory, may be represented by a constant value of the shearing-strain energy, and hence by a constant value of the sum of the squares of the three principal stress differences. In the second of the previous papers,15 however, evidence was presented that the limiting yield stress decreases with increase in the volume stress, the algebraic average Of the three principal stresses.* This in fluence of the volume stress becomes prominent only in the field of triaxial tension. In the two previous papers,".'5 diagrams were presented to show the variation of the technical cohesion limit, yield stress, and ultimate stress with the combination of principal stresses and with plastic extension. Those diagrams and the resultant • Any stress system ma? be resolved into a polarsymmetric stress causing pure volume strain and a combination of pure shearing stresses. which cause no change of volum

Jan 1, 1945

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The effects of increasing hydrogen content, introducing a notch, and changing the strain rate on properties of titanium and one of its alloys were investigated over a range of testing temperatures from —196° to 200°C. Both high purity and commercial purity A-55 titanium were used as representative a materials, while a commercial Ti-8 pct Mn alloy was used for an a-P alloy. It was found possible to analyze the data, using the ductile-to-brittle transition temperature concept. Increasing hydrogen, the presence of a notch, and increasing the testing speed raised the transition temperature for the a materials. The presence of hydrogen and notches raised the transition temperature of the a-B alloy also. However, increasing the testing speed generally decreased the transition temperature of the a-p alloy. IN previous papers, the authors have shown that hydrogen is most detrimental to the notch-bend impact toughness of a-titanium' and to the tensile ductility of a-B titanium alloys.' These general effects have been confirmed by Kessler and co-workers," and by Kotfila and Erbin." Kessler showed that the slower strain rate in notch-rupture tests was a more sensitive measure of hydrogen embrittle-ment of a-B alloys than the tensile test. In the present paper the authors cover, with tensile and notch-bend tests, the effect of testing speed, notches, and testing temperature on hydrogen em-brittlement. High purity and commercial purity titanium, examples of u materials, and a commercial a-,f3 Ti-8 pct Mn alloy were investigated. The purpose of the investigation was to correlate the factors producing embrittlement. Materials The high purity titanium for this investigation was obtained by arc-melting crystal bar from Foote Mineral Co. into 1 Ib ingots. As-cast hardnesses for these ingots ranged from 60 to 90 Brinell. The arc-melted ingots were forged to % in. diam rods at 1470°F. These rods were swaged to & in. diam at room temperature prior to machining of the specimens for hydrogenation and testing. The commercial A-55 titanium and the Ti-8 pct Mn alloy were obtained from Rem-Cru Titanium Inc., as % in. diam rod. The A-55 titanium was hot swaged to 1/4 in. diam at 1300°F prior to machining of the specimens for hydrogenation and testing. The a-p C-11OM alloy was hydrogenated prior to hot swaging to 1/4 in. roc1 at 1300°F. Hydrogenation prior to fabrication permitted testing of the a-P alloy in the equilibrated and stabilized condition. The equilibration and stabilization treatment used was an air anneal for 1 hr at 1300°F, followed by furnace cooling to 1100°F and then air cooling. Hydrogenation was done in a Sieverts apparatus described previously.' The hydrogenation treatment consisted of heating for 1/4 to 1/2 hr at 820 °C in purified hydrogen, slow cooling to 680"C, holding 1 hr for homogenization, and rapid cooling to room temperature. Intended hydrogen levels for the a-tita-nium materials were 0.05, 0.5, 1.0, 1.5, and 2.0 atomic pct—about 15 to 430 ppm. For the Ti-8 pct Mn alloy, the intended hydrogen levels were 0.05, 0.5, 1.0, 2.5, and 5.0 atomic pct—about 15 to 1100 ppm. The material for the 0.5 atomic pct level of hydrogen was vacuum annealed prior to hydrogenation to increase the accuracy of the addition. Vacuum annealing to remove hydrogen consisted of heating for 6 hr at 820°C, and resulted in a hydrogen content of about 10 to 15 ppm. When hydrogen contents were above 0.5 atomic pct—100 ppm—the hydrogen was added without prior vacuum annealing.

Jan 1, 1957

By G. S. Cole

The temperature has been measured ahead of stationary solid-liquid interfaces under conditions approximating luzidirectional heat flow and therefore unidirectional solidification. Natural convection flow patterns may be deduced from the temperature distributions , temperature fluctuations, and shape of the interface. Fluid flow increases with the height and the rate of heat transfev through the interface and this is further manifested by a deviation of the interface from aflat vertical plane. The influence of fluid flow on solute inhomogeneity during alloy crystal growth can be inferred from the observed temperature distributions. A buoyancy force exists in the liquid ahead of a vertical solid-liquid interface, caused by a difference in density between cold fluid near the interface and warmer fluid in the bulk liquid. When the viscous and inertia forces in the melt exceed this buoyancy force, a flow of fluid takes place, termed natural or free thermal convection. Natural convection in purely liquid systems has been extensively studied for many years. 1"u On the other hand, fluid flow during horizontal crystal growth has oniy recently been the subject of experimental investigation."-25 The requirements for horizontal crystal growth differ from other heat flow systems. The small aspect ratio (ratio of height of cold wall to length of fluid) has never been considered. The uniform furnace gradient which supplies heat radially (and not necessarily symmetrically) differs from previous boundary conditions of uniform heat flux at the cold and hot ends. And most important of all an isothermal s/l interface is present which can adjust its shape and position to conform to heat and fluid flow. All of these boundary conditions involve complexities which cannot be readily solved analytically. Preliminary observation has demonstrated the penera1 shape of the natural convective flow pattern in transparent media.20'24'25 The flow is circulatory, directed toward the interface at the surface of the liquid, down and away from the interface at the bottom, and then up at the hot end of the melt. During crystal growth such a flow may interact with the solute boundary layer at the s/l interface to affect solute incorporation.M'1B|28'i!T Evidence has also been presented recently to show that thermal convective flow will affect the structure of ca~tin~s.~~-~~ The rate of heat transfer (conduction plus convection) in a given fluid system is a function of the temperature difference between the hot end of the liquid and the s/l interface and the height of the interface. At the lowest values of these variables* all heat is *It has been shown' that adverse temperature gradients as low as O.OOS°C oer cm are sufficient to cause convection. transferred by conduction. When the temperature difference or interface height are increased, laminar fluid flow commences and heat transport takes place by laminar convection as well as by conduction; turbulent heat transfer takes place at higher values of these variables. In the transition region between laminar and turbulent flow, boundary layer separation takes place; fluctuations in temperature are also noted and increase in amplitude and frequency as turbulence becomes dominant. In this paper, fluid flow patterns in the melt ahead of a stationary interface are deduced from observations of temperature distribution and fluctuations, heat flow rate, and interface shape. The fluid flow ahead of advancing interfaces and the effect of such flow on solute incorporation may be inferred from these measurements on stationary interfaces. Observations during enforced fluid motion will also be considered. EXPERIMENTAL PROCEDURE The metal was contained in a lava boat 10 cm in length, 1+ cm in width, and 2 cm in height, as shown in Fig. 1. A water-cooled, molybdenum block heat-sink is at one end of the boat; surrounding this assembly is a slotted stainless-steel tube noninductively wound with a nichrome heating element. Temperature was measured by 38-gage Chrome1 vs Alumel thermocouples sheathed in 0.05-cm-diam graphite-coated stainless-steel tubing, which were moved longitudinally and vertically through the melt by means of a two-dimensional motorized micrometer stage. In some experiments the thermocouple junction was exposed, but in the majority of experiments the junction was welded to the sheath tip; no significant difference

Jan 1, 1968

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received' little study on the part of wire mills, particularly those that have commenced operations in the last few years.

Jan 1, 1930

By B. H. Kear, S. M. Copley

Stress-stvain curves are presented for Ni3Al (y') cvystals in several ovientations, deformed in tension and compression at constant displacement rate, at temperatures from 70° to 2000°F. Both the yield stress and wovk havdening increase with temperature, with the magnilude of the effect dependent on ovientation. The yield stress maximum occurs at 1500°F in [001], at 1400°F in [011], and at 1200°F in [111]. The suppression of the yield stress peak in [011] and [111] orientatiorzs is due to the onset of cube slip, rather than octahedval slip, a1 elerated temperatures. The temperature and orientalion dependence of work hardening in nominal single slip orientations corvelates with changes in the CRSS ratio for octahedral slip and cube slip, in agreement with a model for work hardening based on pinning of screw dislocalions by cross slip from an octahedral plane into a cube plane. It is concluded that the unique plastic properties of y' have a decisive influence on both ductility and strength characleristics of y +y' nickel-base superalloys. It has long been recognized that the strength of y + y' nickel-base superalloys depends on the precipitation of the y' phase [basically Ni3(Al,Ti)]. This paper presents new data on the strength characteristics of single crystals of simple y' (Ni3Al), and forms the first step in a systematic program aimed at elucidating the mechanisms of hardening in the complex commercial alloys. 1) EXPERIMENTAL PROCEDURE Single crystals of off-stoichiometric NiA1 were grown from the melt under vacuum by a modified Bridgman method. The melt was poured into a preheated alumina mold and crystal growth was promoted from one end by gradient cooling. The crystals were homogenized by annealing in hydrogen at 2400° F for 72 hr followed by furnace cooling. Chemical analysis of samples taken from several crystals gave an average composition of 88.2 wt pct Ni. Spectrographic analysis gave as the principal impurities in weight percent— Si (0.02), Mg (0.01), Fe (0.02), Ti (0.002), Cu (0.008), and Co (0.03). Tensile specimens with specifications as in Fig. 1 were prepared by a series of operations involving electrical discharge machining, precision grinding, and electropolishing. Compression specimens with dimensions 1/4 by 1/4 by -3/4 in. were prepared in a similar manner, except for the initial shaping operation using a precision cut-off wheel/two-circle goniometer unit to give selected crystal orientations. Specimens were deformed in a Baldwin-Wiedemann testing machine with furnace attachment, using a strain rate of 5 x 10-4 sec-1. The strain measuring device consisted of extension arms attached to the tensile grips (or compression plattens) at one end and leading out of the furnace to an LVDT at the other. Temperature was controlled by a thermocouple placed in contact with the specimen. According to the known phase diagram for the Ni/A1 system,' when an alloy of the specified composition is cooled from the melt, primary y (nickel solid solution) dendrites grow at the expense of the liquid phase, which becomes enriched in aluminum. At the eutectic composition the remaining liquid freezes as a two-phase mixture of y + y' (Ni3Al). Upon further cooling, a solid state transformation occurs, involving the precipitation of y' in the primary dendrites, and the complete transformation of the eutectic mixture to massive y'. The as-cast structure consists, therefore, of y + y' dendrites with interdendritic regions of massive y', i.e., transformed eutectic, Fig. 2. 2) DISCUSSION OF RESULTS 2.1) Stress-Strain Curves. Fig. 3 shows tensile stress-strain curves for crystals in orientations close to [001] deformed at temperatures from 70° to 2000°F. Both the yield stress and total elongation are strongly temperature-dependent. At 70°F, easy glide is absent, and the work hardening coefficient BIT - G/300. At T > 1500°F, the negative slope of the stress-strain curves is due to pronounced necking in the crystals. The yield stress maximum at 1500° F corresponds with a minimum in the ductility, Fig. 4. The extensive duc-

Jan 1, 1968

By A Andersen

DURING an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investiga-tion was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this sys-tem as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa's6 and M. Okamoto's7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. S. Smith's latest work on the copper-silicon system8 was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter's diagram and ours checked in all essen-tial features, except the temperature of the peritectic line above 830° C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centered cubic with a lattice constant of 2.848 A.. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexag-onal phase, and to avoid confusion this designation will be adhered to in the present paper.

Jan 1, 1939

By J. R. Stack, H. H. Alexander

Prior to 1915, numerous attempts were made to treat tin concentrates in the United States, but for various reasons they were unsuccessful. Tin ore is said to have been found in nearly every state, but none of the deposits has proved to be of commercial importance. An annual output of a few hundred tons in Alaska is the only domestic production; hence any considerable production of tin in the United States must be from foreign ores. The most promising occurrence of tin was found in the Black Hills, S. Dak.; in the early development stage, it was called the Cornwall of America. Associated with the tin is tungsten The story is told that an exceedingly fine specimen of the Black Hills ore was sent to England to encourage stock promotion; the desired effect was produced until a skeptic chipped off a small piece, which the analysis showed to be wolframite. First Attempts at Smelting One of the first promising attempts at tin smelting in the United States was made by R. T. White at Bayonne, N. J., in 1903. Mr. White, after spending some time in England studying the methods of tin smelting, organized a company called the International Tin Co., and erected a plant to treat tin concentrates from the Straits of Malacca. About the time the plant was completed, the English Government placed an export duty of 40 per cent. ad valorem on tin concentrates exported to other than British smelters, which duty made it impossible to operate this plant so the enterprise was abandoned, As this export duty is still effective, the only source of tin-ore supply for the United States is the Bolivian concentrates. Bolivian Tin Concentrates Unlike the alluvial placer deposits, nearly all Bolivian tin occurs in lode deposits and some of the highest grade ores contain only a small

Jan 1, 1924

By Henry S. Rawdon

Any laboratory corrosion test, as judged from the practical point of view, is valuable only to the extent that it foretells what will, in all probability, occur in service. Such a test is most properly to be considered as a "pilot test," that is, a test which indicates the direction along which action may be expected to occur rather than as a truly quantitative test which would be expected to tell just how and to what extent the action would proceed. It is generally recognized that laboratory corrosion tests should be chosen with particular reference to the character of service expected for any particular type of metal, so far as it can be foreseen. Even when this requirement has been fulfilled, however, the question whether the actual service behavior of the material is in accordance and general agreement with predictions based upon such laboratory tests is always a pertinent one. The information available in the technical literature bearing on the correlation between the service behavior of metals from the corrosion standpoint, and the results obtained with the same metals in laboratory corrosion tests is very meager, indeed. The results which have been obtained in weather-exposure tests of sheet duralumin which form the body of this discussion are presented here for their bearing on this particular phase of the problem of the corrosion resistance of duralumin. Although the exposure tests described have not been completed, in the sense that all of the tests, in the series initially laid down, have been accomplished, still the general trend shown by the results is so clear that a number of definite conclusions at this stage (subject, of course, to possible modification in the light of later results) are believed to be warranted. The tests reported upon here form one phase of the much broader study of this subject which has been under way for several years in which the National Advisory Committee for Aeronautics, the Bureau of Aeronautics of the Navy Department, the Army Air Corps and the Bureau of Standards have cooperated. Without the very helpful cooperation of the manufacturers in furnishing the

Jan 1, 1929

By B. K. Larkin, H. R. Bailey

A model Of heat flow in an underground combustion process is studied. This model includes convection effects and thus is more general than previous studies which considered conduction as the only mechanistn for heat transfer. Both linear (tube run) and radial (field application) geometries are considered. The effects of ignition heaters, vertical losses and finite source width are considered for the linear case. The results are in the form of equations and are presented in graphical form for a number of cases. Convection effects increase frontal temperatures about 25 per cent over those computed for conductive transfer for typical field operating conditions. This increase in temperature is a result of heat being transported toward the front by the injection gas. Even greater temperature increases are realized as the per cent oxygen in the injection gas decreases. It is well known that compression costs are of considerable importance in estimating the economic feasibility of underground combustion. By assuming an ignition temperature for the combustion fuel, predictions of limiting conditions on fuel density and injection rate necessary to sustain the combustion zone are made. For typical field conditions, at least 0.75 lb/cu ft of fuel are needed with air as the injection gas. If the injection gas is 10 per cent oxygen and 90 per cent nitrogen, this figure is 0.69 lb/cu ft. INTRODUCTION The possibility of increasing oil recovery by underground combustion has been considered for many years. Recent field tests indicate that the underground combustion process is technically feasible. The economic feasibility depends to a large extent on the amount of air which must be injected to sustain combustion. Prediction of the success of employing underground combustion in a particular reservoir must be based on existing field tests, laboratory tube runs"' and solutions of mathematical or analog models. Vogel and Krueger5 devised an electrical analog of the heat transfer problem in an underground combus-ion process. They considered the problem of heat conduction from a cylindrical source with increasing radius assuming no vertical losses. Bailey and Larkin and Ramey solved the corresponding problem including vertical losses by considering a mathematical model of the conduction process. Ref. 9, 10 and 11 also present information related to the subject study. The present paper generalizes these results to include both conduction and convection mechanisms for heat flow. A model of the conduction-convection process is described. The partial differential equations governing this model are written and solved for a number of cases of interest. The formulas are evaluated and the results are presented graphically. A CONDUCTION-CONVECTION MODEL Description of the Model A number of models are employed in this paper, each of which approximate a particular physical situation depending on the geometry, i.e., linear or radial flow, the type of vertical heat losses, the nature of the source, etc. The geometry for both the linear and radial case is shown in Fig. 1. A particular linear model is described in this section, and variations from this model are described in later sections of the paper. Consider a homogeneous, semi-infinite porous prism with lateral sides insulated as shown in Fig. 1. The left end, x = 0, is heated for a time t, with a plane heater supplying a constant heat flux and during this time; gas (nitrogen) is passed through the pores of the prism at a constant mass flux. At time t, the heater is turned off and air is injected in place of the nitrogen. This causes combustion to take place, and a uniform source of width 1 is formed which moves at a constant velocity v, to the right. The frontal velocity v, is related to the gas velocity v,, through stoichiometric considerations

By Ancel St. John

DURING a session on coal and coke at the February, 1926, meeting of the American Institute of Mining and Metallurgical Engineers, the writer called attention to the important work on the X-ray analysis of coal1,2 being carried on in England by C. Norman Kemp and his associates. This aroused so much interest that a paper on the subject was requested for the October meeting. It has seemed advisable to make this paper a preliminary survey of the present status in the application of X-ray methods to coal problems and to follow it from time to time with further articles as the art develops. A survey of this sort naturally divides itself into two parts, radioscopic analysis of the distribution of constituents through the body of the coal, and diffraction analysis of the state of association of the elementary components. In this article the subject matter concerning radioscopic analysis has been drawn almost entirely from the writings of Kemp and his associates and the illustrations have been specially furnished by him. It is a pleasure to record here a great indebtedness for this courtesy and cooperation. The subject matter and illustrations concerning diffraction analysis are taken from the author's unpublished researches.

Jan 10, 1926

By S. B. Twiss, P. R. Basford

The relationship between areas of iron powders, briquettes, and sintered compacts and tensile strength has been determined. It has been found necessary to distinguish between two types of areas which exist in such powders—a macroscopic area due to the shape and size of particles and a microscopic area due to pores and cracks in the surface. Only the macroscopic area, specifically the area due to particle irregularity, contributes to tensile strength; the microscopic area cannot be forced into contact with adjacent particles ond does not participate in bond formation. Of the two methods of area measurement employed in this study—permeability to liquids and gas-phase adsorption—only the former is useful for determining the roughness factor. A measure of this roughness, (area measured by permeability to liquid) -f- (orea of powder with the same size distribution, but made up of spherical particles), is shown to be uniquely related to tensile strength at constant density. The other important factors in determining the strength of sintered-metal compacts are the density and presence or absence of surface oxide. THE manufacture of metal parts by the process of powder metallurgy is an important and rapidly growing industry. Progress has been rapid and continuous, largely because of the excellent research in the field. Nevertheless, the process remains inherently complex and empirical. Several investigators have shown that the properties of the final compact must depend on many variables; namely, shape,' size distribution,"-" nd compositiona of the original particles, the pressure necessary to compress to the desired density, the density of the compact, the time and temperature of sintering, and so on. Through the application of some new techniques to the study of powders and compacts, and the correlation of a number of observations of known variables, the present paper attempts to clarify and simplify the underlying theory of the powder-metallurgy process. Any theory must start with the obvious fact that the strength of a compact, its most useful property, is due to the formation of welded areas between adjacent particles, and attempt to deduce what effect other variables will have on (a) the area and (b) the intrinsic strength of these welds. Such welded areas can be demonstrated by electron micrographs, as in Fig. 1. It was believed that (a) could be most directly studied by means of surface-area measurements on the original powders and on the compacts made from them; the area decrease should be related closely to the welded area. A representative group of eleven iron powders from commercial sources, and made by a variety of processes, was chosen for this study. In addition to the surface-area measurements, correlations were established between the tensile strength and all the known variables which might possibly affect it. The results are quite unexpected. They indicate that the situation is much simpler than the authors had anticipated. The strength of the sintered compact is determined, indeed, by no more than three variables; viz., the irregularity of the original particles, the density of the compact and, in exceptional cases, the amount of surface oxide. All three had been recognized previously as having some effect on the tensile strength, but in the absence of the special techniques and interpretations to be developed here, there could be no suspicion that they were the only relevant variables. Materials and Methods Material—All the iron powders were commercial products obtained from the Amplex Division of Chrysler Corporation. Powders A, B, C, and J were very pure electrolytic iron. Powder D was made from oxidized scrap reduced by heating with an excess of cast iron. Powder E was a high-grade iron ore reduced by hydrogen. Powder I was prepared by atomizing molten cast iron in an air blast, quenching the droplets in cold water, and crushing the coarse powder. Mill scale (oxide) is added and the mixture heated to reduce the high carbon content. The other powders were all prepared by reduction of iron oxides, such as mill scale. They

Jan 1, 1959

By H. A. Wriedt

Zinc-vapor pressures in equilibrium with bcc solutions of zinc and iron at 703.5", 757", 793", and 900°C were measured by an isopiestic method. Thermody-na?nic properties of zinc in these solutions were derived directly and those of iron with a Gibbs-Duhem integration. Zirzc and iron exhibit large, positive, and moderately temperature-sensitive deviations from ideality. Excess enthalpies and Gibbs energies are positive in the ranges studied. It has been establzshed in relating published phase equilibria to the Gibbs energies of forming solid solutions that positive departures from ideality also exist in the fcc solutions. Tlze stability, as defined by Darken, of the bcc solutions is small but positive at 703.5"C. Its decrease with decreasing temperature indicates that a miscibility gap may exist in the stable or metastable bcc solutions at lower temperatures. The changes of thertnodynanlic properties relatable to changes in magnetic state are minor compared to other changes due to alloying. The accuracy with which the relation between lattice parameter and composition of the bcc solutions is known has been improved. Zinc increases the lattice parameter of a iron by O.ZOZA per unit atom action zinc to at least NZn = 0.25. TO our knowledge, only Ciganl has previously investigated thermodynamic properties of the bcc solutions of the Fe-Zn system. He measured zinc-vapor pressures in the temperature range from about 320" to 360°C by an effusion technique. We have measured the vapor pressures of zinc in equilibrium with bcc solutions of zinc and iron at 703.5", 757", 793", and 900°C by an isopiestic technique. This investigation and the pursuant thermodynamic computations are part of a program for studying several properties of these solid solutions. In the appendix we report a remeasurement of the relation at room temperature between the lattice parameter and zinc content. Related work not reported herein embraces measuring the diffusivity2 of zinc in ferrite at 700" to 900°C and the Curie point temperature3 as functions of composition. EXPERIMENTAL METHOD AND APPARATUS Purified iron at a series of constant temperatures was saturated with zinc at a series of constant zinc-vapor pressures, the range of conditions being so limited that the equilibrated solid solutions were ferri-tic. The equilibration was conducted in long capsules, Fig. 1, that had been evacuated, gettered with titanium, and sealed. The purified iron, part of a vacuum-melted ingot of electrolytic-iron stock (Glidden Co. 1044-grade), had the impurity contents listed in Table I. It was used in the form of millings about 0.001 in. thick. A zinc of 99.999 pct purity (United Mineral and Chemical Corp.) and later one of 99.9999 pct purity (Cominco Products, Inc.) were used, with no observed difference in results. Sufficient zinc was placed in the capsule (separate from the iron and kept at a different temperature) to supply the vapor phase and the iron alloy, while leaving a pool of pure liquid zinc throughout the run. The imposed temperature of the residual zinc pool fixed the vapor pressure of zinc throughout the capsule; condensation was avoided at other locations by making this the lowest temperature in the capsule. Two common complications of nonisothermal systems were, we believe, effectively absent from ours: first, molecular species other than monatomic have no appreciable concentration in zinc vapor at 700" to 900~~: second, the development of zinc-pressure differentials in the capsules was suppressed by use of relatively large-diameter tubing and the absence of diluents in the zinc vapor other than desorbed impurities. The specimens and zinc pool were located at two isothermal zones (each ranging within 1°C over several inches) of a wire-wound, 37-in.-long vertical-tube furnace. The required temperature distribution was achieved by external adjustment of the currents in three electrically isolated windings. The temperatures of the isothermal zones were controlled independently by ther-

Jan 1, 1968

By A. S. Odeh

This paper analyzes the effect of limited entry to flow at the wellbore on the steady-state productivity of a well. Wells that have been opened to flow along a fraction of their productive interval are termed wells with limited entry. Previous work treated the cases of a partially penetrating well, a well producing from the central portion of the productive interval and a well in which several intervals equally spaced were open to flow. In this paper the open interval can be located anywhere within the productive interval. Thus, in a sense, it generalizes previous work. The finite cosine transform was used to arrive at a solution for steady-state flow of a slightly compressible fluid. The solution was programmed for a CDC 1604 computer. Numerical vaIues for rd = 660 ft, r, = 1/4 ft, and range of sand thickness of 20 to 200 ft are presented in graphical form. The effect of rd and r, values on the result is shown in a table. The correct calculation of skin and damage ratio in the presence of limited entry to flow is explained and illustrated by examples. Moreover, the paper shows how to calculate the net decrease in productivity due to the combined effect of limited entry and perforations. INTRODUCTION In some wells only a fraction of the productive interval is open to flow. Location of this fraction is usually dictated by formation characteristics and reservoir behavior. For instance, if a gas cap exists, the open interval is located away from the gas-oil contact to prevent any possible gas coning. Wells that intentionally have been opened to flow along a fraction of their productive formation are tened wells with limited entry. Obviously, unintentional completions of this type also exist. Limited entry to flow decreases well productivity. Magnitude of the loss depends on the fraction of the formation open to flow, on the thickness of the sand, on the location of the open interval and on the ratio of rd /r, where r , is well radius and rd is the drainage radius of the well. The use of pressure buildup data on producing wells to calculate the condition of the formation around the wellbore is an accepted practice. van Everdingenl and Hurst2 introduced the concept of she skin factor s considered to be due to a thin layer of different permeability immediately around the wellbore. These authors dealt with the case of a well of complete radial geometry, i.e., a well with open-hole completion that completely penetrates the formation. The presence of a low-permeability skin results in a loss of productivity, as does limited entry. Therefore, if pressure buildup data obtained on a well with limited entry are used to establish the presence or absence of skin (i.e., formation damage), and a correction is not made for this loss of productivity, the calculations would result in an erroneous skin value. They might indicate the presence of formation damage when in reality there is none, or they might indicate a value larger than the true value. This could lead to an incorrect basis for planning remedial measures. Muskat3 studied the problem of partially penetrating wells for the case of incompressible flow. He presented equations and figures which allow estimation of loss in productivity. Brons and Marting,4 using equations based on Nisle's work,5 studied the loss of productivity for three cases. The first was for a partially penetrating well; the second was for a well producing from only the central portion of a productive interval; and the third was for a well in which several intervals equally spaced were open to flow. Their work was for steady-state depletion-type reservoirs wherein the well radius of drainage is established and the fluid is considered to be slightly compressible. Considered in this paper is the problem of wells with limited entry in which the open intervals are located anywhere within the productive sand. The finite cosine transform is used to arrive at a

Jan 1, 1969

By Verne E. Hooker, Robert M. Becker

The evaluation of in-situ rock stresses from measurements of the change in diameter of a borehole that is stress-relieved by overcoring has become a common practice. Generally the stress evaluation has been based on isotropic relations whereas rock in varying degrees is aniso tropic. A plane elasticity solution fora circular hole along one axis of an orthotropic medium has been adapted to evaluation of in situ stress. The necessary elastic parameters for this evaluation may conveniently be obtained from static tests on the overcore in conjunction with a consistent orthotropic thick-wall cylinder solution. The method and equations for the laboratory and field evaluations are summarized and illustrated. The determination of in-situ rock stresses from boreholc deformation measurements has gained widespread acceptance. Hastl measured the change in diameter of a borehole that was stress-relieved by drilling a larger concentric core; this overcoring method has produced a major portion of the field data for recent stress evaluations in rock. These evaluations are based on the elastic properties of the rock, which are conveniently determined by testing the overcore.6-8 The stress evaluation and the overcore testing procedures generally assume isotropic relations whereas rock is anisotropic in varying degrees. Recently, an anisotropic plane stress solution was adapted for evaluation of in-situ stress9 and a related plane strain solution was developed for the testing of stress-relief core. 10 The present paper unifies the stress evaluation and overcore testing procedures for a general class of anisotropic rock. Equations are presented for calculating the state of stress in a plane normal to the borehole, and a consistent thick-wall cylinder solution is given for determining the necessary elastic properties. In addition, a complete example of stress evaluation from laboratory and field data is presented, and the order of error in computing the state of stress from isotropic relations is illustrated. Several limitations of the results should be emphasized. All results assume small linearly elastic deformations of a homogeneous medium. Rock characterized by orthotropic, transversely isotropic, and isotropic elasticity is considered; however, the anisotropic results assume a special relation among certain elastic constants in addition to geometric orientation with respect to a plane of elastic symmetry. For some stress determinations in rock, these may be severe limitations. On the other hand, the anisotropic evaluation procedure involves little additional effort and is much more flexible than the corresponding isotropic evaluation procedure. The collection of field data is identical. The laboratory determination of elastic parameters is no more difficult and time-consuming for the anisotropic than for the isotropic model. Only the calculations require some additional effort for the anisotropic evaluation, and this additional effort is eliminated by use of a small computer. The flexibility of the anisotropic procedure is greater because more than two independent elastic constants are available in fitting rock data. For the special relationship assumed among orthotropic constants, five independent elastic constants are available for the determination of in-situ secondary principal stresses as compared with two independent elastic constants for the isotropic model. Much of the material presented is either directly from the literature or adapted from the literature through superposition or the usual transformations. Consequently, only enough detail for clarity of presentation is included. RELATIONS FROM ANISOTROPIC ELASTICITY Materials that have three mutually orthogonal planes of elastic symmetry are called orthotropic. By directing the axes of the coordinates perpendicular to these planes, Hooke's law for an orthotropic solid 11 is

Jan 1, 1970

By Leon Eliel

TEN years ago a broad knowledge of aerial mapping, coupled with a smattering of geology, qualified one to speak on the subject of the appli-cation of aerial mapping to geology. Today, with aerial maps a common tool in the hands of expert geologists on every continent throughout the world, it would be nothing short of presumptuous for the author of this paper, who is not a geologist, to give any geological statements on his own authority. Relatively, today we are only purveyors of general geological gossip, with a definite case here and there by way of illustration. But we can present a story of the really marvellous strides that have been made in the evolution of aerial mapping, built around a skeleton of geological tidbits, from which some useful conclusions may be drawn. The average geologist goes about reading his aerial maps much as one would approach the problem of deciphering a cryptogram. To begin with, typical key expressions appear in recurring sequences and under certain conditions. If once the meaning of these isolated bits of infor-mation can be ascertained, the message begins to take meaning. In a similar fashion, the geologist works out his key from aerial maps of territory with which he has some familiarity. He learns that a certain type of thin, white line may mean a vein of quartz. He sees that a certain change in the photographic tone of vegetation on the ground reflects two kinds of soils on opposite sides of, a contact. He sees that a certain type of alignment of topographical features often means a fault. He learns that by the erosion pattern .he can frequently distinguish soft formations from harder ones. And so, bit by bit, he ties together the information of the picture with his experience on the ground until he develops a reasonably creditable capacity of interpretation. Through the complete gamut of surface conditions, ranging all the way from flat, arid, exposed desert terrain to dense jungle, or rugged mountains, the evidence from which the geologist must make his inter-pretation varies with bewildering profusion. The quality of photographs which are obtainable may range from perfect pictures in the desert to almost useless smudges in the steaming jungles. One thing he has learned with certainty-the airplane carrying its mapping camera is a superb reconnaissance tool, only awaiting his ingenuity in correlating the pictures with the ground to simplify most exploratory problems.

Jan 1, 1936

By J. G. Early, F. V. Lenel, G. S. Ansell

The isothermal shrinkage rates of copper-powder compacts were determined in the temperature range from 760o to 1060oC. The rates for compacts fabricated from a pure spherical copper powder were compared, on the one hand, with those fabricated from a spherical powder containing a dispersion of aluminum oxide in the copper matrix and, on the other hand, with those fabricated from a pure copper powder having irregularly shaped particles. The irregular copper-powder compacts shrank much faster than the spherical copper-powder compacts and these, in turn, shrank faster than dispersion -strengthened copper -powder compacts. The experiments were run under a small external load. By varying this load, the stress dependence of the isothermal shrinkage rate could be measured for compacts from spherical-copper powders. This stress dependence was found to be approximately proportional to the 4th (dispersion-strengthened alloys) or 4.5th (pure metals) power of the stress. It is concluded that the material-trans port mechanism is due to dislocation climb rather than to Herring-Naharro creep. In this investigation the isothermal shrinkage rates of compacts made of copper powder with an average particle size of 70 g in the temperature range from 780o to 1060°C were studied. The aim of the investigation was to determine the mechanism of material transport responsible for the shrinkage of these compacts. Since the phenomenon observed in this investigation was shrinkage of compacts at high temperatures, it will be necessary to consider all the material-transport mechanisms possible in sintering. It is unlikely that evaporation and condensation, surface diffusion, or even volume diffusion of vacancies, in which surfaces of small radius of curvature are vacancy sources and those of larger radius of curvature vacancy sinks, will materially contribute to a sintering process involving shrinkage, i.e., one in which the centers of adjacent particles move towards each other. The two principal mechanisms which were considered were the so-called Nabarro-Herring mechanism and a plastic deformation mechanism by dislocation movement. Both of these mechanisms were originally conceived to explain creep, i.e., the plastic deformation of metals at elevated temperatures under a constant applied stress. The shrinking of metal-powder compacts which was studied in this investigation can be readily treated as a creep process. This means that the shrinkage rates observed are considered as creep rates under the influence of an applied stress. It is true that the stresses in sintering experiments are generally not constant but decrease continually with time, but, by considering creep rates or shrinkage rates over a relatively short time interval, the small changes in stress during this time interval can generally be neglected. Nabarro-Herring microcreep is a high-temperature deformation mechanism which is caused by a diffusional flow of vacancies from boundaries under a tensile stress towards those under a compres-sive stress. Herring1 has shown that in this type of microcreep the strain rate e is proportional to the applied stress and follows an equation of the form ma, aexp(-Q/RT) [l| where <j is applied stress, Q is the activation energy for self-diffusion, R is the gas constant, and T is the absolute temperature This type of creep can explain the shrinkage of a porous compact. The surface of the pores are subjected to the tensile stress of surface tension, while the grain boundaries are under a compressive stress also due to surface tension. Vacancies diffuse from the pore surface through the lattice to the grain boundaries, where they are eliminated. In order to maintain vacancy equilibrium at the pore surface the vacancies leaving the region of the pore surface are replenished from the volume of the pore, which means that the pores shrink.

Jan 1, 1964

By D. A. Koss, R. O. Gordon

Changes in the ultrasonic attenuation in steel specimens have been observed during tensile tests. Samples of AISI 1020, 1045, and 1095 steel quenched and tempered to a spheroidized condition have been used. Both attenuation and microstrain measurements fail to reveal preyield dislocation motion in the as-tempered specimens. Upon reapplication of the load to samples in the strain-aged condition there is a large preyield attenuation increase but no observable micvostrain up to 90 pct of the flow stress. These and other observed changes can be related to changes in the free disloca-tion density and the average dislocation segment length. The results show that the increase inflow stress in the strain-aged condition is caused by increased fric-tional stresses rather than by dislocation pinning. Strain aging is found to proceed through three distinct stages. The second of these follows the t2,3 law and is characterized by an activation energy of 20 kcal per mole. RECENT years have seen substantial progress in the understanding of the sharp yield-point phenomenon in metals; the influence of solute atom pinning of dislocations, of dislocation multiplication, and of the stress dependence of dislocation velocity on the stress-strain curve has been investigated. Evaluation of the relative importance of these factors in the various metals and alloys is not complete, however, because observation of the stress-strain curve alone is not sufficient to determine the yield mechanism. In the experimental study of the sharp yield point it would be desirable to be able to directly observe the dislocations in a bulk specimen. Ideally, the observations should be made during deformation because of the rapidity of recovery processes in lightly strained metals. While direct observation of dislocations under these conditions is not possible, certain physical properties sensitive to the dislocation structure can be observed while a test specimen is undergoing deformation. Of these properties, one of the most useful is the ultrasonic attenuation. The total observed attenuation, a, is due to a number of causes: acoustic diffraction, scattering by inhomogeneities in the structure, heat flow, magnetostriction, and dislocation damping. Satisfactory measurements of the absolute a are difficult to make because all of these factors cannot be evaluated in any given specimen, but changes in a due to changes in the dislocation contribution alone can be reliably observed by appropriate technique. Because dislocation damping is sensitive to small concentrations of long, free dislocation segments, observation of acoustic attenuation due to dislocations is particularly useful in the study of the early stages of plastic deformation. In the experiments to be described, acoustic-attenuation measurements have been made on steel samples as these were pulled through their yield in tension. While many details of dislocation-damping phenomena in the bee metals remain obscure, the main characteristics of this type of internal friction are established. At low strain amplitudes and at frequencies well below that of dislocation resonance (the conditions of these experiments) the dislocation contribution to a is given by1 where A is the density of freely oscillating dislocation segments, L is the average segment length, B is the damping constant for a moving dislocation, w is the frequency, O is an orientation factor, C is the dislocation line tension, and t is a numerical factor relating average segment length to the distribution of lengths. Because of its fourth-power dependence on L, a is highly sensitive to changes in dislocation free segment length such as might arise from unpinning, recovery, jog formation, or dislocation intersection. The above equation is not valid near the resonant frequency of dislocations, but the segment length in steel is believed to be much too short to cause over-damped resonance near 10 Mc; this will be discussed later. In the present experiments plastic-strain measurements with a sensitivity of 2 x 10-5 were also made during the early stages of loading in order to detect preyield strain. The general plan of the experiments is to observe

Jan 1, 1967

By Cyril Stanley Smith

Although alloys of copper and silicon were examined several years ago,&apos; and their excellent mechanical properties were shown, it was not until C. B. Jacobs 2 introduced manganese in small quantities to the alloys that they became of commercial importance. A few years ago The American Brass Company took over the patents and commenced to manufacture the alloy under the name "Everdur." The present study of the constitution of the ternary system was undertaken in order to reach a fuller understanding of the behavior of the alloy. Review of Previous WORK on the BinaRy Systems There have been no papers published dealing with the constitution of the ternary system, although some tests of the mechanical properties have been described," which indicate that there is a change in solubility with temperature. Copper-silicon System The copper-silicon system has been studied in detail by the author and is described in two papers published in 1928.V he portion of the diagram up to 8 per cent. silicon, as determined by this research, is reproduced in Fig. 1. The author&apos;s previous papers include a complete review of the work of other investigators and it is not necessary to deal further with this system here. Copper-manganese System The copper-manganese system has been investigated by several workers, notably Lewis,5 Wologdine,6 Sahmen7 and Schemtschuschny,

Jan 1, 1930

By Charles Wraith

THE property of the Roan Antelope Copper Mines, Ltd., is situated at Luanshya, north-central part of Northern Rhodesia, and is connected with the main line of the Rhodesia Railways, Ltd., by a 24-mile branch line from N&apos;dola. Most of the material and supplies that are not available in Africa are shipped into the country via Beira, on the East Coast of Africa, a distance of 1473 miles from Luanshya and the nearest ocean port. The output of copper is shipped by rail to Beira and thence by boat to the market. Passenger travel is mostly via Cape Town, a distance of 2162 miles from Luanshya. Excellent passenger trains operate on regular schedules between Cape Town and Northern Rhodesia. Luanshya is 13° south of the equator at an elevation of 4000 ft. above sea level, and has a mild healthful climate. During the rainy season, from October to March, the rainfall averages 53 in. The area is pro-fusely covered with vegetation. An ample supply of water for industrial and domestic purposes is available throughout the year. The more important supplies for smelting purposes, such as wood, coal, limestone, silica, quartzite, and clay for "dolly" mud, are con-veniently available. Excellent grades of coal, coke and firebrick are obtained from the Wankie Colliery Co., Ltd., Southern Rhodesia. The Wankie colliery has just completed the erection of equipment for the manufacture of silica brick. An ample supply of quartzite of good grade is available for this purpose. Silica brick is also obtained from the Belgian Congo and from India. Limestone is quarried from a large deposit a few miles from Bwana Mkubwa, which is 30 miles by rail from the smelter. An abundant supply of clay for "dolly" mud and for lining launders is available within a short distance of the smelter.

Jan 1, 1933

By R. G. Agarwal, Ramey Jr. H. J., Al-Hussainy R.

Although it has long been realized that gas recovery from a water-drive gas reservoir may be poor because of high residual saturations under water drive, it appears that only limited infomlation on the subject has been available until recently. This study was performed to show the qiiantitative potential importance of water influx. Results indicate that gas recovery may be very low in some cases: perhaps as low as 45 per cent of the initial gas in place. Gas recovery under water drive appear to depend in an important was on: (I) the prodirction rate and manner of production; (2) the residual gas saturation; (3) aquifer propertie.); and (4) the volumetric displacement effciency of water invading the gas reservoir. The manner of estimating water-drive gas reservoir recovery can vary considerably. Examples are: the steady-state tnethorl. the Hurst modified steady-state method, and various unsteady-state methods such ac. those of van Ever-dingen-Hurst, Hurst, and Carter-Tracy. The Carter-Tracy water influx expression was used in this study. In certain cases, it appears that gas recovery can be increased significantly by controlling the production rate and manner of production. For this reason, the potential importance of water influx in particular gas reservoirs should he investigated early to permit adequtrtr planning lo optirtize the pay reserves. INTRODUCTION In recent years, the economic importance of natural gas production has become increasingly apparent. This has been evidenced by more intensive exploration efforts aimed at gas production, and exploitation of both deep, as well as low-permeability gas reservoirs. Technical developments such as deep-penetration fracturing have made development of such formations economically feasible. Unfortunately, water influx has forced abandonment of a number of gas reservoirs at extraordinarily high pressures. Although reservoir engineering methods for estimating water influx have long been available, it appears that application of these methods to the water-drive gas reservoir has been sporadic.&apos;a Available methods for estimating water influx which can be applied to the water-drive gas reservoir problem include the steady-state method,1 the Hurst modified steady-state method and various unsteady-state methods such as those of van Everdingen-Hurst. Hurst, and Carter-Tracy. Interesting applications of these solu- tions to gas reservoir and the aquifer gas-storage problems have appeared recently.3,12,14 The experimental study of residual gas saturations under water drive by Geffen et al. in 1952 indicated that residual gas saturations could be extremely high. A value of 35 per cent of pore volume is often used in field practice when specific information is not available. The study of Geffen et al. showed that residual gas saturation might be much higher in some cases. Naar and Henderson concluded that the residual non-wetting phase saturation under imbibition should be about half of the initial non-wetting phase saturation. The Naar and Henderson result that residual gas saturation under water influx should be about half the original gas saturation is recommended as an estimate if laboratory measurements are not available. Thus, it is clear that a considerable portion of the initial gas in place might be trapped in a water-drive gas reservoir as residual gas at high pressure. A full water-drive would result in loss of residual gas trapped at initial reser.voir pressure. Consideration of transient aquifer behavior leads to the conclusion that high-rate production of water-drive gas reservoirs could result in improved gas recovery by reduction of the abandonment pressure. However, there appears to be little quantitative information on this possibility. One of the few advantages of water-drive gas production appears to be improved deliverability through water-drive support of the reservoir pressure. There may also be an advantage in higher condensate recovery caused by pressure maintenance for gas-condensate water-drive reservoirs. In view of the preceding, this study was made to assess the potential importance of water-drive in gas reservoir engineering. The Carter-Tracy approximate water-influx expression was used because this equation offers some advantages in hand-calculation which do not appear to have been generally recognized.&apos; However, calculations were performed in the main with a high-speed digital computer to permit evaluation of the effect of water-drive under a large variety of conditions. CALCULATION METHOD Water-drive gas reservoir performance can be estimated in a manner completely analogous to oil reservoir calculations: a materials balance is written for the reservoir, and a water influx equation is written for the aquifer. Siniltaneous solution provides the cun~ulative water influx and the reservoir pressure. When reservoir performance data (gas produced and reservoir pressures) are available, it is usually possible to match performance data to determine the initial gas in place and the water influx parameters —

Jan 1, 1966