Search Documents

By N. W. Sager, H. W. Mossman

The arrangement and general dimensions of the reverberatory furnaces and waste-heat boilers for the Nos. 2 and 3 smelting units at the McGill plant of the Nevada Consolidated Copper Corporation are shown in Fig. 1. Each of the two reverberatory furnaces has its own set of waste-heat boilers, and before February, 1932, each furnace, when it was in operation, delivered waste-heat gases to its own boilers only. In January, 1933, the idea was suggested of using some of the waste-heat boilers as economizers to operate in conjunction with the waste-heat boilers that were generating steam. The execution of this idea gave rise to the gas-flow scheme depicted in Fig. 1, the advantages of which were obvious, particularly so in view of the fact that for some months prior to the adoption of this scheme the smelting had been confined to No. 2 furnace, with No. 3 furnace and its boilers idle. The waste-heat gases from No. 2 furnace pass through the boilers serving this furnace as steam-generating units, thence through the original exit duct to a point where a bulkhead diverts the gases in a reverse direction through two of the boilers of No. 3 furnace. After the gases have traversed these two boilers, another bulkhead placed in the duct between No. 3 furnace and its boilers causes them to traverse still one more boiler, from which the gas path leads to the stack. In this scheme the last three boilers traversed by the gases, i.e., the boilers behind No. 3 furnace, function as economizers and preheat the feed water for the two steam-generating units directly serving No. 2 furnace. This discussion will give consideration to the results obtained in waste-heat recovery by the scheme shown in Fig. 1, and, further, will compare these results with those obtained before the boilers of No. 3 furnace were set up to act as economizers, but before going into the detail of heat generation, distribution and recovery, will present some additional details of the equipment. All boilers in this waste-heat plant are of the Stirling type. The two behind No. 2 furnace, acting as steam-generating units, of class 13, are 40 tubes wide and rated at 1112 boiler hp., while the three boilers behind No. 3 furnace, acting as economizers, are also of class 13, but 28 tubes

Jan 1, 1934

By Howard N. Eavenson

WHEN the A.I.M.E. was formed 75 years ago the bituminous coal industry was in its swaddling clothes, although it had been operating for more than a century and coal was being mined in every state now producing it, and its output had long passed that of anthracite. In 18/1, the value of bituminous coal was about seventy per cent of the value of all metals produced and more than one fifth of the value of all products of mines, both metallic and nonmetallic.[1a] While many of the operating mines then shipped by rail, most of the development was along waterways, although the canal era of transportation was nearly at its end. Coal mining is a heavy industry and one of the best measures of its progress is its output throughout the period. Fig. 1 shows this graphically from 1800 to 1945. From 1870 to 1910, the production-which is very nearly the consumption-almost doubled every decade, a most amazing growth. In 1918, in World War I, a peak was reached and a decline began, which ended in 1932. A gradual recovery then started, interrupted in 1938 but culminating in the record output of 1944, when, owing to World War II, a tonnage of 619,576,000 was produced. It is evident that the forces leading to the continuous increase ending in 1918 have spent themselves and that only unusual conditions will require so large a production again. The postwar conditions of World War II will probably

Jan 1, 1947

By S. F. Emmons

THE first paper which appears in the published Transactions of our Institute is that read by our respected Secretary at its first meeting in Wilkes-Barre, in May, 1871. It is entitled The Geological Distribution of Mining Districts in the United States, and presents a brief but masterly review of what was known of the distribution of our deposits of useful minerals, particularly the metals, not only from a geographical but from .a geological stand-point. At the request of Dr. Raymond, I agreed, somewhat hastily, perhaps, to write for this occasion a brief sketch of the geological distribution of the deposits of the useful metals in this country, in the light of the increased knowledge of the present day. In the time given no personal investigation was possible, and as it was therefore out of the question to attempt to make anything that could be considered an original contribution to the history of our ore-deposits, I have been obliged to limit myself to an examination of such published data within my reach as bore upon this subject, and could be consulted in the brief time I have been able to give to it. Had the geological investigations undertaken by the Tenth Census been continued systematically by the United States Geological Survey or by the Eleventh Census, it might have been possible to make a fairly-complete review of the subject. As it is, the principal result of my examination 1 has been to show how very unequal

Jan 1, 1913

By Cyril Jones

13.9-1. Introduction. Any mining venture or project is undertaken with a view of gaining some benefits, which, with the modern limited corporation, means earning a return to the stockholders for the use of their funds. Thus, any manager, when confronted by an opportunity of expending funds, must realize that the funds should generate a satisfactory return. The problem then becomes one of how the manager should best expend, if he should expend, funds for opportunities that become available to him. In the evaluation of a mineral property, or of a project within an operating mineral property, there must be cognizance of the fact that the final return is dependent on many factors that are not present in other industries. The primary factor in mining operations is the orebody, which has a diminishing life. This diminishing life gives the decision maker a range of choices; for by expending more capital for a larger plant, he can work the deposit out in a shorter period (16). This may, in fact, maximize the return on the investment. Alternatively, he may wish to maximize the total profits, a course which usually requires a lower capital investment and allows a longer working life for the deposit before final depletion. Other factors that have great importance in the evaluation of mining projects are the taxation treatment of mining profits from the viewpoint of depletion, depreciation, and investment credit. Investment opportunities involve expending funds at the present time in return for future benefits. These future benefits have a degree of risk in that the annual amounts of benefits and their duration cannot be fore- cast accurately. The treatment of risk in economic analysis involves the quantification of the degree of variability of the expected future benefits and also of the initial capital expenditure. This treatment in mineral exploration may be extended to cover the initial search for an orebody

Jan 1, 1968

By Ralph Schilthuis

SEVERAL investigators1-8 have reported evidence of the existence of native or connate water in oil-and-gas-bearing strata. Both water and salt have been detected in cores of oil sands that yielded oil and gas exclusively when produced. Electrical logs often reveal unexpectedly low resistivity through oil and gas sands, indicating the presence of some material that is a considerably better conductor of current than oil and gas. Furthermore, calculations9 of the oil and gas content of reservoirs based upon production and reservoir-pressure decline data indicate appreciably lower values than are arrived at under the assumption that the pore space is occupied completely by oil and gas. ORIGIN AND OCCURRENCE OF CONNATE WATER IN OIL-AND-GAS-BEARING FORMATIONS The view has been expressed,10-15 and is generally agreed upon, that the expulsion of oil and gas material from source beds and the subsequent migration and accumulation occurred in the presence of salt water. As the strata that usually form reservoirs for oil and gas were laid down by, or in the presence of, ancient seas, the pore space within the strata must have been saturated with salt water before the entrance of the oil and/or gas. Thus, the accumulation of oil and/or gas in the upper regions of structures suitable for reservoirs must have required displacement of the connate water therefrom. In the absence of any forces other than gravitational, it would be expected that the displacement of the connate water out of the zones finally occupied by gas and oil would be complete, and that the vertical distribution of gas, oil, and water in a reservoir would be strictly in the order of their densities. Apparently, however, surface and interfacial forces that will not permit complete segregation of the fluids are active within the capillary spaces comprising a reservoir. The effects of these forces on both accumulation and production of oil and gas have been the subject of study by a number of investigators. 16-37

Jan 1, 1938

By L. S. Reid, R. L. Hunntington

The study of the flow of oil and gas mixtures through oil-bearing formations has received special attention from the petroleum industry within the past few years, and has resulted in a series of research projects based upon various phases of the flow of heterogeneous fluids through porous media. Obviously, the low cost of producing oil during the flowing life of a well makes it desirable to obtain production by natural flow as long as possible and to effect a maximum recovery of oil and gas by the utilization of reservoir energy through efficient methods based upon a thorough knowledge of reservoir characteristics. Despite the extensive research that has been carried out, there is little information available on the behavior of oil and gas mixtures flowing through reservoir formations. This makes it impossible to predetermine the optimum operating conditions for flowing wells. A differential pressure must exist in the reservoir in order to induce flow toward the well. It is a well established fact that with homogeneous fluids the relation of pressure drop to linear distance traveled is a straight-line function as long as the flow is viscous. However, in regard to gas-saturated oils, a number of investigators1l,2,3 have reported that the flow characteristics are materially altered as some of the lighter hydrocarbons are liberated from the oil to form gas while the fluid passes through the reservoir. Most of the work done has been concerned primarily with steady-state flow of liquid-gas mixtures. Cloud1 has studied the effects of saturating crude petroleum oils with various gases, together with the resultant pressure gradients under steady flow conditions, noting that unsaturated oils flowed faster and yet maintained lower pressure gradients than saturated oils. The work of Wyckoff and Botset4 has constituted a major step in the interpretation of heterogeneous fluid flow; especially their concept of

Jan 1, 1938

By C. W. Clark

Two papers have been written previously concerning operations at the Montreal East plant of Canadian Copper Refiners Limited. The first one,1 written in 1932, described silver-refinery operations at the time for producing silver and gold bullion from tankhouse anode slimes; the second,2 published in 1933, consisted of a description of the entire plant. Since publication of these papers the refinery has become the world's larg-est producer of refined selenium. The first selenium was produced in August 1934. Tellurium production on a. commercial scale followed in October 1935. This paper will deal with selenium and tellurium produc-tion and also with present operations in the silver refinery. Blister cakes from Hudson' Bay Mining and Smelting Co., Flin Flon, Manitoba, and commercial anodes from Noranda Mines Limited, Noranda, Quebec, are refined at Montreal East. Both these bullions have unusually high gold, selenium and tellurium content. The average assay of raw slimes produced from domestic and Noranda anodes is about 40 per cent Cu, 3600 oz. per ton Ag, 800 oz. per ton Au, 22 per cent Se and 3.7 per cent Te.

Jan 1, 1938

By L. W. Eastwood

THE recrystallization and grain-growth phenomena of cold-worked metals have considerable industrial importance because of their role in the fabrication of metals. For this reason, and because of the general academic interest in the subject, these processes have received consider-able attention since the time of J. E. Stead's paper1 on The Crystalline Structure of Iron and Steel. There are considerable differences of opinion regarding the theory of recrystallization and grain growth and also differences in the observation of the modus operandi of the processes themselves. The value of many of the existing quantitative data on grain growth is decreased by the failure to distinguish between the grain sizes just after complete recrystallization and those resulting from coales-cence. For this reason also, the value of the diagrams of stable grain sizes, like those produced by Bass and Glocker2 and Czochralski3, is lessened in so far as an interpretation of the facts of recrystallization is concerned. It is hoped that the data presented in this paper will help to clarify and to simplify the facts relating to recrystallization, and at the same time will show that some of the present-day conceptions are unten-able. A paper on the theory of recrystallization, with additional data, will be completed in the near future by the writers.

Jan 1, 1935

By Joseph B. Umpleby

The oil industry is at the parting of the ways in relating fundamental engineering concepts to legal interpretations and field practices. The old concept, based on an erroneous analogy to wild game, that oil and gas are migratory substances and belong to him who reduces them to possession regardless of their point of origin in the reservoir, has come to be quite generally recognized as the basis of many of the serious ills and extravagances of the industry. The chain of consequences resulting from this erroneous conception has been traced elsewhere and need not be recounted here. The important problem at this stage in the development of the industry, when laws are being revised by legislative action and modified by court decisions; when added powers are being exercised by voluntary committees and official regulatory bodies; and when the need for control of output has forced itself to the forefront, is to see to it that new law and action are based on sound engineering concepts. Reservoir Energy Common Property Since the study of gas instituted by the Marland committee of the American Petroleum Institute in 1927, a great mass of information has accumulated concerning the function of gas in the development and production of oil. This wealth of data leads to the conclusion that every oil pool contains three resources: Oil, gas and reservoir energy. I take it that the central problem of this symposium is the ownership of these three resources and that "source" and "utilization" are involved because of their bearing on ownership through the demands of equity and conservation. In order to facilitate the discussion, permit me to state categorically, that: The oil and gas in a particular tract should belong to the owners of the mineral rights in that particular tract, but the reservoir energy should be common property of all owners of mineral rights in the pool I take it that apportionment of oil and gas among owners according to the relative amounts that exist in place in their respective tracts is

Jan 1, 1933

By F. W. Davis

This paper deals in a general way with certain of the necessary requirements of refractories for the open-hearth furnace. The refractories in common use for the different parts are discussed both as to the service they are giving and their suitability to withstand existing chemical, thermal and physical requirements. The relation between the service and allowable cost of a refractory is discussed and suggestions are requested on these points. The purpose of this paper is not to report, to the Institute, the results so far obtained in the survey, by the Bureau of Mines, of the metallurgical requirements for open-hearth refractories, but to present an outline that we hope will serve as a basis for discussion. The systematic survey that the Bureau proposes to make has not been outlined, although considerable preliminary work has been done in the way of interviewing open-hearth superintendents in several of the larger steel plants from the Chicago district eastward. At the several conferences so many of the opinions were diametrically opposite, when considering the same point, that it was thought that such an opportunity as the Institute offers in the way of a clearing house for moot metallurgical topics should not be overlooked. For this reason, the paper has been prepared as a basis for a discussion which, it is believed, will be of value in outlining the program of the Bureau. D. A. LYON, Assistant Director. THE importance of securing suitable refractories for metallurgical operations is daily becoming more universally recognized; particularly in the manufacture of open-hearth steel, where the life and earning power of the furnace depends largely on the judgment and care exercised in the selection of the correct quality of refractory for each of the parts. Any innovation that would make available to the steel manufacturers refractories with longer life or better suited to their needs than those now employed, and at a cost that would permit of their use, would be of enormous value to the industry at large. It is quite probable that revolutionary changes would not be necessary. Material now used in some parts of

Jan 3, 1924

By H. K. Shearer

Oil production in north Louisiana in 1937 was 28,668,070 bbl., an increase of 1,896,925 bbl., or 7.1 per cent over 1936, as against an increase of 178 per cent from 1935 to 1936. Gas production of 301,148 million cu. ft. from gas wells and 17,330 million cu. ft. of casinghead gas, a total of 318,483 million, was an increase of 33,483 million cu. ft., or 11.7 per cent over 1936. Well completions numbered 716, with 411 oil wells, 175 gas wells and 130 dry holes; compared with 346, 109 and 78, respectively, in 1936. There were 58 wildcat dry holes. In addition to the wildcat producers described and tabulated with the fields, there were two small, shallow gas wells in Sabine and Tensas Parishes, which did not open fields of any present importance. At the close of 1937 there were only five wildcat tests actually drilling, with nine others shut down or temporarily abandoned. Chief interest during 1937 was in development rather than discoveries. The only real discoveries were two deep gas and distillate fields, Bear Creek and Ruston. There were also three completions of gas-distillate producers from deeper formations in old fields, of which the most important was at Cotton Valley, one discovery of oil in a previously known gas sand and five or six extensions of some importance. Geological Section The columnar section in south Arkansas (Fig. 1, p. 317) also applies in north Louisiana, with a few changes noted below. The oldest known formation in north Louisiana is a bed of rock salt. Except on salt domes, only one well at Rodessa has been drilled into this salt, but it has been penetrated by a number of wells in south Arkansas. Salt domes have been discovered near Vicksburg and Hattiesburg, Miss., and a deep well in Limestone County, Texas, has drilled into rock salt. In Louisiana the distance between the "interior salt-dome basin" and a salt dome of the "Gulf Coast salt basin" is hardly 60 miles. In short, evidence is accumulating to indicate that all of Louisiana, with the possible

Jan 1, 1938

DESIRABLE as it is to summarize what has been set forth in preceding chapters, the task can only be approached with great hesitation. What follows represents the personal views of the author at the moment of writing, reserving the privilege to change them on more mature reflection or in the light of further evidence. With that reservation they may be stated somewhat as follows. Education for the mineral industries falls into two categories; general education and technical vocational, using the word vocational not in its usual sense but to signify preparation for specific activities, in which sense a law school is a vocational school. Even at the beginning, as indicated in the first chapter, mineral industry education was partly general and partly technical and that relationship still persists, because technical education requires a firm basis of general education. Our general American system is to provide free public general education through the twelfth grade, or completion of high-school work, though there are already many technical vocational high schools, and even in a community where nearly all the young people are preparing for entrance to college there will be some who wish to qualify for employment at the end of the high-school course, or even on completing junior high. Our educational system, therefore, has not only to provide education for those who intend to proceed beyond the twelfth grade but also for those who, for a variety of reasons, may wish or be forced to cease full-time education at any level between the first and twelfth grades. This study has been chiefly concerned with the problem of what kind and how much technical education to provide for those who have completed the twelfth grade and who wish to make their living in the mineral industries. The obvious fact that the mineral industries employ all sorts of trained persons,

Jan 1, 1941

By A. E. Harnsberger

IT is obvious that details such as the physical and chemical properties and methods of heat-treating of the materials mentioned must be omitted in a paper on the subject of materials used in oil-refinery pumps1. Only sufficient identification is given to enable the reader to find additional information from already published data. Also, the subject covers many operating conditions, but only the most important services can be discussed here. To the oil refiner, the pumping equipment is of vital interest. Practi-cally every refinery operation, from the charging of crude oil to a dis-tillation unit to the shipping of refined products, involves some form of pumping machinery. Intermediate refining stages involve a great variety of pumping machinery to carry out successfully the aims of the refinery technologist. Temperatures at which oils are handled vary from -50° F. to 900° F. Pressure may vary from subatmospheric to 2000 lb. per sq. inch. The selection of the proper materials involves a careful consideration of the conditions under which the particular pump must operate. The four most important considerations are temperature, pressure, corrosion, and abrasion or wear. Consideration of temperature "may be divided into three parts: (1) extremely low temperatures of the order of -50° F.; (2) temperatures at atmospheric or slightly above; (3) temperatures from 200° to 900° F. Pressures fall into two groups: (1) pressures reached by ordinary trade pumps of the order of 200 lb. per sq. in., (2) extreme pressure conditions involving pressures as high as 2000 lb. Noncorrosive and corrosive oils can be treated differently. Under the latter falls corrosion in the presence of water, which will occur up to 250° F. The second type of corrosion occurs in high-temperature pump-ing equipment, with temperatures from 450° to 900° F., largely caused by sulfur compounds. There are also other corrosive conditions met with

Jan 1, 1935

By R. V. Lukes, H. W. Scheeline

Knowledge of a large number of the physical properties of the hydrocarbons is needed in the calculations and studies of the production engineer. Since experimental data on these properties of the individual hydrocarbons and their mixtures are available in only a relatively few cases, the use of generalized correlations has developed rapidly in the last decade. The generalized correlations of pressure, volume and temperature,' enthalpy2 and vapor-liquid equilibria13 on the basis of reduced temperatures and pressures, are outstanding examples of this development. These correlations are of particular value to the production engineer interested in the flow of oil and gas, since they can be used to estimate the conditions under which segregation of phase occurs as well as the composition, density, and relative amounts of the phases. The technique of using the correlations for such estimations has been published by several authors4 and will not be considered in this paper. A considerable number of data have been obtained to check the generalized pressure-volume-temperature correlations, and these data indicate that such relations hold for the hydrocarbons from methane to heptane. The accuracy is in general sufficient for most engineering pressure-volume-temperature calculations. However, the generalized correlations of enthalpy and vapor-liquid equilibria have in general been developed from the pressure-volume-temperature correlations by thermodynamic calculations and only a relatively few experimental data are available to check these calculated values. The calculations from pressure, volume and temperature are likely to lead to large errors in the calculated enthalpy and vapor-liquid equilibria. Thus, in the calculations of enthalpies, slopes of the pressure-volume-temperature data are employed, and determining these slopes can greatly amplify small errors in the original data. In the vapor-liquid equilibria calculations it is necessary to have the pressure-volume-temperature relations of the mixture, and the latter propertics are much more questionable than those of pure components, particularly in the critical region. A considerable number of experimental data are

Jan 1, 1939

By David B. Reger

Sharp declines of initial production of both oil and gas occurred in West Virginia during 1943. There was only a small decrease in the number of ncw wells, but these wells did not show the quantities of oil and gas that might have been expected. The same situation prevailed both as to routine drilling in old pools and as to exploratory wildcat wells. Out of 42 wildcats drilled, 19 resulted in small commercial gas wells, and 2 in small commercial oil. No new oil pools were discovered, but the proved limits of several old pools were considerably extended, giving 4200 acres of newly proved oil territory. Three new gas pools, resulting from discoveries made in 1942 and former years, came into definite activity. The newly proved gas territory in these and in various extensions of old pools is 39,000 acres or more. It is doubtful whether the newly proved reserves of either oil or gas will balance current withdrawals. The account of operations, as gathered from trade journals and other reporting services, shows that 696 new wells were drilled, resulting in 82 oil wells with 919 bbl. of daily new production; 475 gas wells with 454,735,000 cu. ft. of daily open flow, and 137 dry holes. Also, 57 old wells were drilled to deeper sands, with 3 bbl. and 11,484,000 cu. it. of added production. On the new wells, the oil average was 11.2 bbl. per well per day, and the gas average was 957,337 cu. ft. per well per day. On new wells the ratio of dry holes to completions was 19.68 per cent. On deeper drilling the ratio of failures was 14.03 per cent. The greatly decreased average initial gas-well production in 1943, as compared with 2,270,406 CU. ft. per well in 1942, is directly attributable to the abrupt decline of completions in the Charleston gas field, which reached its peak in 1942. Production of oil for the year was estimated by the U. S. Rureau of Mines as 3,349,000 bbl., as compared with 3,574,000 bbl. in 1942. Production of natural gas for the year is estimated by the author as 210,000, 000,000 cu. ft., compared with the U. S. Bureau of Mines final figures of 215,193,-000,000 cu. ft.* in 1942.

Jan 1, 1944

By W. N. Tanner

The wire-rope hoisting conditions at the mines of the Anaconda Coppcr Mining Co. in Butte, Mont, are very severe because of the conditions under which it is necessary to operate. A study was made, in the fall of 1919, for the purpose of changing these conditions in order to obtain longer rope and sheave life. There are at present in Butte hoisting engines equipped with wire rope as follows: 9 main hoists using flat ropes. 7 main hoists using 1 1/2-in. rope. 5 main hoists using 11/4-in. rope. 6 shafts using 11/8-in. rope. 2 chippy hoists using 11/4-in. rope. 9 chippy hoists using 11/8-in. rope. 15 shafts using 1-in. rope. 7 shafts using 7/8-in. rope. 1 shaft using 3/4-in. rope. In addition, there are a number of sinking engines wing 5/8-in, 3/4-in., 7/8-in., and 1-in. (15.9, 10, 22, and 25 mm) rope. THe flat ropes run from 1/2 by 71/2 in. (12.7 by 1905 mm.) to-3/8 by 4 1/2-in (9.5 by 114 mm.) and are used on the older hoisting engines, which arc set comparatively close to the shaft. Because of swelling and moving ground at some of the shafts, these ropes present certain difficulties ill operation that are more pronounced than with round ropes; they are, therefore, being superseded by round ropes as newer engines are being installed. They are, however, much more easily inspected and repaired than round ropes. In general, the practice in Butte is to use hoisting engines equipped with 12-ft. (3 7 m.) cast-iron drums, smooth faced, for 11/2-in. rope and 6-ft. cast-iron drums, smooth faced, lagged with 3/8-in. steel plate for 11/4 l1/8 and 1-in. (31.7, 28.6, 25 mm.) rope in main and chippy shafts. Cast-iron head sheaves, 12, 10, and 6 ft. in diameter, with grooves

Jan 1, 1923

By Laurence Delisle

The aim of this paper is the description of a technique to be applied to the study of sections of metal powder particles, less than 20 microns in diam. with the electron microscope, by the replica method, using for replica a material such as formvar or parlodion. This work originated with the study of particles of tungsten powders. Such particles were too small to be examined in sufficient detail with the light microscope. On the other hand, examination with the electron microscope of the powders dispersed in the supporting film was not found satisfactory because: 1. It did not permit differentiating between single particles and aggregates. 2. It did not show the true outlines of the particles but only the projection of a whole surface. 3. No details appeared. For that reason it was attempted to make replicas of sections of the particles imbedded in a mounting material suitable for polishing and etching. The method proved satisfactory for the examination of tungsten powder and was then extended to car-bonyl nickel and carbonyl iron powders. Procedure Several mounting materials commonly used in ordinary metallography were investigated. The problem consisted in finding a mounting material

Jan 1, 1950

By Richard Zinszer

Application of electric logs has been used in correlation of subsurface structure to determine the size and shape of the oil reservoir. Such a knowledge is hardly complete until saturation and productivity are determined for the various horizons. It is difficult to use electric logs successfully for this purpose because of the many factors that influence the curves. In this work an effort was made to establish an empirical correlation between formation resistivity for a series of electric-log curves and water saturation and oil productivity of sand. Electric logs were obtained by recording with 10 different electrode spacings through the same interval of a well. In the analysis of these curves all factors except two, a dependent and independent variable, were held constant. The interval studied had been cored and a large number of samples were analyzed in the core laboratory in order to compare the values of permeability and saturation with the measured values of formation resistivity. Results of this analysis indicate: (1) the depth to which mud filtrate enters a sand body, (2) a correlation between permeability and sand resistivity for shallow penetration depths, and (3) that the water saturation for an oil sand can be determined from the measured sand resistivity after making suitable correc- tions for sand thickness. The proceduer in the last method depends on a correction for thickness factor and a theoretical curve. The accuracy of the theoretical curve is now being tested in the laboratory. In an effort to place the analysis of electric logs on a quantitative basis, there is need for a better understanding of the many factors that influence an electric-log curve. These factors may be large differences in sand thickness, permeability of the sand, salinity of the interstitial water, mud resistivity, formation temperature, and other sources. A number of examples were presented by Archie,' which treat the effect of sand thickness on measured resistivity. He compared the true resistivity of a sand with the observed resistivity for sands 8 ft., 16 ft., and 24 ft. thick, and found the observed resistivity Of the 8-ft. sand to be approximately

Jan 1, 1943

By H. B. Aaron

DIFFRACTION micrography provides a useful tool for studying complex strain fields. Newkirk1 observed an X-ray diffraction effect due to strain interactions at the intersection of slip lines in LiF and attributed this effect to a reduction of primary extinction due to strain-gradients. It is the object of the current study to correlate the observations and rationalize the appearance of the strain fields around intersecting slip planes in x-ray extinction contrast studies by a semiempirical method. Fig. 1 shows typical strain patterns observed by Newkirk on (200) reflections in LiF using chromium radiation and a variation of the Berg-Barrett (B-B) technique. In other reflections (e.g., {220}) the strain patterns are absent. If one defines a vector 3 along the striations from the more to the less dense portion, and a vector v in the direction of the X-ray beam parallel to the reflecting plane, such that both 3 and v lie in the reflecting plane of the crystal, Fig. 1, then the positions of the striations on (200) reflections appear to be confined such that where is the angle between v and 3, Fig. 1. It will be seen later that 3 is the projection of Sb on the reflecting planes. In some instances the strain effects are observed only above the slip plane, Fig. l(C), in others only below, Fig. l(D). Where the strains appear to be both above and below the slip line, Fig. l(E), one sees that there are actually two slip lines present, Fig. 1(F) and (G). Furthermore, the strain patterns are observed in the vicinity of the intersection of emergent edge dislocations (diagonal lines on the micrograph) with emergent screw dislocations (horizontal lines on the micrograph), e.g., Fig. l(HJ) and (MN), but not in the vicinity of the intersection of two emergent edge dislocation arrays, Fig. l(HJ) and (KL). However, in the latter case the contrast of the dislocation array itself is reduced along (KL) and increased along (HJ). Line (AB) in Fig. 1 is the edge of the crystal, and the material to the left of (AB) is the side of the sample. Any empirical correlation will have to include most, if not all of the aforementioned observations. Lang2 and Newkirk1 determined that the condition for contrast is given by g-b#0 [2] where b is the Burgers' vector and g the diffraction vector (normal to the reflecting planes). If one assumes that the direction of the observed strain fields is given by the vector sum of the slip vectors (Sb1) of the intersecting slip planes, then Eq. [2] may be generalized to g-S#0 [3]

Jan 1, 1963

By L. D. Jaffe, John H. Hollomon

THE hardenability concept has become widely used during the last few years for the choice and substitution of steels. Before the work of Grossmann,1 the systems for predicting hardenability from chemical composition could be used only over a narrow range of composition. Grossmann introduced a comprehensive system, which has been effective in calculating the hardenability of most types of moderate or low-alloy steels. However, occasions .often arise that require the calculation of the hardenability of high-alloy steels from their chemical compositions. Experimental determinations of the hardenabilities of such steels indicate that the Grossmann system predicts much greater hardenabilities than are realized. The fact that cases do arise in which the Grossmann method does not, apply indicates that the fundamental hypothesis of the system may not be generally applicable. It seems advisable to re-examine not only Grossmann's system but also the concept of hardenability itself. HARDENABILITY If steel parts are to possess a martensitic structure after quenching, they must first be austenitized and then cooled through the pearlite and bainite transformation ranges sufficiently rapidly to avoid the formation of pearlite, bainite, and proeutectoid products.* If, on cooling, these transformations are avoided, the resulting structure can consist only of martensite (and retained austenite). The hardenability of a steel is measured in terms of the severity of the cooling conditions necessary to avoid the pearlite and bainite transformations. The less rapid is the cooling necessary to prevent the formation of bainite and pearlite, the higher is the hardenability. The pearlite and bainite reactions appear to be differently affected by the alloying elements. Not only is this indicated by the published isothermal transformation data, but recent work by Zener2 affords a rational interpretation of the differing effects of the alloying elements. Manganese,3 for example, appears to decrease the rates of the pearlite and bainite transformations by equal percentages, while molybdenum4,5 is approximately 10,000 times more effective in retarding the pearlite than in retarding the bainite transformation, on the basis of isothermal measurements. In some steels, the formation of bainite restricts the formation of martensite while

Jan 1, 1946