Search Documents

By D Obeng, D Alexander

Over the past five years, commodity prices have been high and the focus of many plants has been æthe more metal the better, at whatever costÆ. In the recent economic crisis, the focus has shifted more to reducing the cost of production and operating at higher efficiency. Since 2002, JKTech has partnered with the Century mine in north-west Queensland to transfer technology and understanding through the good, bad and ugly economic environments, using methodology and techniques arising from research at the Julius Kruttschnitt Mineral Research Centre (JKMRC) and other research institutions around the world as part of the AMIRA International P9 Project. The JKTech studies were concentrated around the primary zinc circuit. During this period, Century expanded the primary zinc regrind capacity, installed additional scavenging capacity, installed and commissioned a Jameson cell for concentrate cleaning in the carbon preflotation circuit, and installed additional primary grinding capacity. Flotation circuit models were developed for each of the survey campaigns and enabled opportunities for further improvement to be identified, implemented and tested in the subsequent campaign.

Jan 1, 2009

This work was instituted to investigate the microscopic structure of brown coals by means of microtome sections cut from them. It was found to be essential to impregnate the coal with some material prior to cutting, because of its powdery and crumbly nature. Of a number of impregnating materials tried, e.g., glycerine gum, gelatine, by far the most satisfactory was paraffin wax. Samples of brown coals for section cutting must be moist. When obtained, they should be put immediately into air-tight tins, and, if they are not to be used for some time, it is desirable to keep them under water containing a small amount of formalin. If the sample is allowed to dry in air, it becomes too hard to be cut. It cannot be softened again even by prolonged soaking in water.PREPARATION OF COALSmall rectangular, blocks were cut from the sample with a chisel and a strong scalpel. The largest block prepared was 3·2 x 2·5 x 0·6 cm. The faces of the block from which sections were to be cut were approximately levelled before treatment. The block was then painted carefully on all sides with two coats of warm aqueous agar, approximately 2 %. This prevented crumbling and breakage of the block during treatment. When the agar was set, the block was placed in water, and all the air removed with a vacuum pump. The water was replaced first by alcohol, then by chloroform, by the usual step transference of a series of liquids, in each of which the block was placed for 24 hours: Ethanol %, 10, 20, 30, 50, 70, 85, 95, 100 (three changes); Ethanol-chloroform, 3: 1, 1: 1, 1 : 3, chloroform pure (three changes) '. The blocks were then embedded in paraffin of melting point 56-58°C. Fresh...

Jan 1, 1947

By Schofield D

The problem of production scheduling is sufficiently complex to negate the use of many conventional optimising techniques as there are numerous and diverse factors that must be considered when trying to produce an optimal schedule. These factors include: grade distribution, orebody geometry, production rate capacity, processing constraints and market price of the minerals amongst a variety of others. In addition it may be observed that many of these factors incorporate a degree of uncertainty and any schedule produced must inevitably consider risk as a primary consideration. The very nature of the problem has limited the use of conventional optimisers. Genetic algorithms use methods based upon evolution and natural selection to produce `optimal' solutions to complex system problems. They are extremely flexible and robust in their nature and it is these characteristics that are important in this particular problem domain. A particular strength of the genetic optimisation approach is the ability to handle the multiple and non-linear constraints that are typically encountered in mine scheduling problems. This paper concentrates on the development of a prototype application of a genetic algorithm to the problem of scheduling the output from multiple production points in an underground mining operation. In particular it.describes a system (GO-SCHED) that can be customised to handle a wide variety of underground scheduling problems. GO-SCHED, a Windows-based system, can interface with a variety of databases and spreadsheets for data input and output and provides a simple intuitive approach to the solution of the scheduling problem.

Jan 1, 1995

A contract for three 20 ft diameter vertically mounted axial flow fans of the same aerodynamic design, was placed by Mount ]sa Mines Limited in 1963. The hydraulic blade pitch changing mechanism, the method of blade fabrication, and the roll out centre casings are features of these fans. Protection devices and fan control are designed for unattended operation and remote control. The erection and commissioning of the fans during 1964-65 is described.

Jan 1, 1967

By W Newton, J Price

This paper outlines the design, justification and performance of a gravity circuit upgrade at the Marvel Loch treatment plant. The design of the upgrade was simple but effective. The key components of the upgrade were the addition of a sluice and a second Knelson Concentrator. The sluice was installed as a pre-concentration step. The upgrade also included the purchase of a Mineral Cone to treat the increased quantity of gravity concentrate. The cost was low because of the use of mostly second-hand equipment. The result was that for a cost of $75 000 the gravity recovery doubled and the overall recovery increased by over one per cent. This paper shows that you do not need to spend millions of dollars to be innovative and successful.

Jan 1, 2000

By N Mangadoddy, P Jampana, S Diddi

The study of air-core dynamics in hydrocyclone operation is essential for predicting separation efficiency in mineral processing. Electrical resistance tomography (ERT) allows non-invasive measurements of hydrocyclone internal flow dynamics. Existing regularisation methods such as Gauss-Newton and TV norms rely on optimisation techniques which have very high computational cost for very fine meshes. In contrast, the monotonicity method has much lower computational cost as it does not solve such minimisation problems. In this paper, results from the monotonicity method, Gauss-Newton (GN) (Tikhonov) and Total-Variation (TV) norm-based minimisation methods for estimating the air-core diameter in hydrocyclones are compared. We study these methods on the laboratory hydrocyclone experimental two-phase flow data. The results obtained are validated against High-speed video (HSV) imaging and Computational Fluid Dynamics (CFD) results. The results on different mesh sizes, in particular for very fine meshes with the number of cells ranging from 30 000 to above 100 000 are also investigated. The data used in this study is obtained from ITS Z8000 ERT system. This system does not measure the voltages on the current carrying electrodes. Since these voltage values are required for the monotonicity method, we implement an interpolation method to compute them. The results show that the monotonicity method provides a closer approximation of the interface between air and the water phases.

Aug 24, 2022

By Ryan CG, Cousens DR, Griffin WL

The proton microprobe is developing into a vital tool in the geosciences, through its high sensitivity for in-situ detection of trace elements in the ppm regime. This paper will describe the instrument at the CSIRO Heavy Ion Analytical Facility at North Ryde, including features crucial to its successful application in the geoscience. Examples of applications in the basic geoscience and mineral industry related research are described briefly. Conditions required for widescale applications in the minerals industry are Discussed.

Jan 1, 1989

By Bogie I, White P. J

Active geothermal systems occur widely in Sumatra and in the Taupo Volcanic Zone (TVZ) of New Zealand. There are also many occurrences of epithermal gold mineralisation in Sumatra, some of which are economic. Minor sub-economic occurrences of gold have been reported in the TVZ but none have yet been mined. There are both similarities and differences in the nature of the active geothermal systems and mineral deposits in Sumatra and New Zealand, which can be systematically related to the tectonic setting. The thicker crust and consequent predominance of silicic volcanism in New Zealand leads to hydrothermal. systems which are little eroded and with limited lateral outflows. The systems in Sumatra are of mixed character, with some of the characteristics of those in andesitic island arcs such as Java or the Philippines, eg a higher proportion of systems with identifiable acid magmatic volatiles, a greater potential for deep erosion and lateral outflows than in New Zealand; but modified by the more oblique component of subduction and thickened crust so that some are localised in volcano-tectonic depressions and consequently have high piezometric levels of primary hydrothermal fluid. The unusual occurrence of calcic zeolites in veins associated with gold mineralisation in Sumatra is thought to be indicative of "satellite" boiling zones along de-gassed hydrothermal outflows.

Jan 1, 1995

In Mount Isa voltage and frequency fluctuations caused. by haulage shaft operation gave considerable difficulties with the initial application of Atomic Absorption Spectro-photometry.The methods used to stabilise the various units ' have been described.- Some other difficulties and the means used to eliminate or reduce them together with a-modified burner design are also discussed.

Jan 1, 1963

By Fowke NC, Williams RJ, Hungerford F

In-seam, directional drilling has been implemented at Huntly West Mine, New Zealand as the most cost effective means of obtaining geological information at a level of detail and accuracy required for planning of longwall ("flexiwall") panels. No geological or geophysical technique tried at the mine prior to 1989 has been able to reduce geological risk to an acceptable level. Surface and in-seam seismic methods have not had adequate resolution. Obtaining the required knowledge via surface drilling would be prohibitively costly, and still not precisely locate or orient faults or the axes of seam "ridges and valleys".A total of 3543 m was drilled at an average of 67m/shift including setting up time. Unplanned delays totalled only 9.6 percent. Major re-interpretation of seam structure resulted from the drilling. Lateral and longitudinal panel grades have been defined. which should be negotiable with the Coalcorp longwall equipment.

Jan 1, 1991

By R Rankine

Backfilling with paste fill has been an integral component of open stoping at Cannington since commencement of operations. Efficient paste filling is critical to successful mining of the Cannington orebody. There has been a deliberate and ongoing effort into research and development of paste, with the focus being to optimise the performance and cost of paste. This paper describes the latest research and operational issues of Cannington paste fill.

Jan 1, 2005

By McAuley T. J

Computer software is an integral part of mining operations today with many sites using six or more software packages on a daily basis. However, the use of these different programs generates the need for substantial staff training. The current trend toward large integrated packages to solve this problem is counter-productive because the relatively small companies producing specialised mining software do not have the resources to develop quality software with all the required features. Software standards are being proposed by various parties but recent history indicates these will be unsuccessful. An alternative approach is suggested using the various standards which have been developed for the Windows operating system.

Jan 1, 1995

With the sinking of the new No. 3 Shaft and the increasing depth and northward movement of the mining operations, improved ventilation of the mine workings became necessary and it was decided to sink a new upcast ventilation shaft midway between No. 2 Shaft and No. 3 Shaft.The shaft is finished to 16 ft. internal diameter and connects with the mine workings at the 2,600-ft. level. It is lined with unreinforced Concrete approximately 12 in. thick. The shaft sinking routine was drilling, blasting and mucking by hand using a 27-cub. ft. capacity bucket. The concrete lining was poured in conjunction with the sinking and was normally finished within 30 to 50 ft. of the shaft bottom.

Jan 1, 1957

By Robinson B, Ham B

Outbursts have occurred irregularly in the Collinsville Coal field since 1954 when an incident claimed seven lives. Further significant outbursts occurred in 1960, 1961, 1972 and more recently in the No. 2 mine in 1978. From the information collected over 25 years a comprehensive program to minimize the hazard of outbursts has evolved. Further developments of techniques to combat outbursts are being developed.

Jan 1, 1980

A novel fracture-plane control blasting technique with particular application in wall-control blasts in mines employing medium to large diameter boreholes is described. It consists of a string of nested holes, each nest consisting of a large diameter charge-hole flanked on either side by a small diameter satellite hole. Each nest is shown to be an analog of a pressurized hole with diametral notches along its length. This 'equivalent-notched' hole concept for generating controlled fractures along preferred directions has been successfully investigated in the laboratory and in the field. The technique has been used to generate controlled fractures on a quarry bench in highly jointed limestone. The resulting blasts with a 250 mm diameter central charge-hole and 50-75 mm satellite holes show that two nests of such holes almost 5 m apart could be joined by a single co-linear fracture. The design range of diameter ratio between charge-hole and satellite hole is 3 to 6 and spacing is 3 to 5 charge-hole radii. With careful matching of explosives and decoupling, and combination of diameter ratio and spacing, it would be possible to connect two nests of such holes more than 20 charge diameters apart by a single controlled fracture plane. The relative merits of the technique against existing wall-control blasts are discussed, and guidelines for practical fracture-plane control blast designs are discussed.

Jan 1, 1990

By Witkowski A

I have the pleasure to present 6 excellent papers in this section all of major relevance to the mining environment of today where competing social, legal and monetary interests and their often complex interaction require serious consideration. This is particularly true today where huge fluctuations in commodity prices makes mining a perilous undertaking while the world increasingly are becoming aware of the serious threat that mans activities has on his environment. The 6 papers deal with such complex issues as safety in an underground environment; How to protect sensitive wetlands well into the next century; The enormeous waterproblems in China and conflicting dewatering/water supply needs; Disposal of contaminated water in sensitive areas and the dynamic interaction between mining companies and legislation.

Jan 1, 1988

By Kendall W. T C

This paper provides a brief overview of the history of the Chaffers Dewatering Project which was successfully commissioned in August 1993. Until the end of 1992 the `Superpit' and the deep mines of the Golden Mile had all been dewatered by a staged pumping system from the 28 level in the Lake View Shaft, which was removed at that time when the Lake View Mine was absorbed into the Superpit. Feasibility analysis had indicated that adaptation of oil industry technology offered the greatest potential for a low cost solution to the problem of dewatering the open pit and deep mines. A KCGM engineer and one of the authors visited the Jackson oilfields to look at the deep well pumping technology in use there in early-1991. In the final analysis a new dewatering station was established in the 23 level crushing station of the Chaffers Shaft using conventional plunger pumps, but the rising main was screwed 178 mm OD (7 inch) casing the suspended from the surface to a depth of 686 metres, and was installed using oilfield personnel and methods. Only the second installation of its kind in Australia, the project achieved the dewatering objective at about half of the capital cost of the more conventional approach and at lower operating costs as well.

Jan 1, 1995

By C Glassock, P Tilyard, T Sandeman

Computer simulation is a well accepted tool for modelling the behaviour of large and complex operating systems. It is a particularly useful technique in complex operations where there are multiple interactions between the inputs and outputs of various unit operations. It can be utilised during the early stages of a project as part of the business case definition phase or the early engineering phases, or alternatively to help understand the various options available in an upgrade or expansion. With the design of a new processing plant to handle a different ore type at Lihir Gold Limited (Lihir), there was concern that the existing conveying system could separately handle the increased tonnages. A simulation model was constructed which allowed Lihir to examine the impact on the conveying system of the new process plant, as well as investigate the effect of different trucking options. As is often the case, once the simulation model was built, further understanding of the downstream bottlenecks was able to be investigated, including the sizing of critical equipment.

Jan 1, 2006

By Walker E. R

IN the early age of steel it was made hy what is known as the cementation proeess, in which wrought iron was embedded in charcoal and heated in a mufflc furnace to a tcmperature of approximately 1100° C. for varying lengths of time, the length of time depending upon the amount of carbon (or better known in thosedays as the degree of hardness) required in the finished product.By this process the resultant product obtained was not of uniform quality, and because of this uncertainty of quality Huntsman was induced, in the year 1740, to introduee what is known as the crucible process.This process consisted of cutting into small pieces the product of the cementation process, placing these pieces in a crucible, and melting them down with the aid of a eoke-fired furnace, after which the molten metal was cast into suitahly shaped ingots, from which could be hammered any desired shape.A section of crucible furnace is shown in Fig. 1. By this means a product, very uniform in character, was produced.The process is still in use, but, owing to its high operating cost, it is mostly eonfined to the production of very high-grade carhon and alloy steels. Its position to-day as a producer of these high-grade steels is, however, being very seriously challenged by the electric process.It was owing to the excessive cost of crucible steels and the need of producing a steel in commercial quantities and at a reasonable cost, that led Sir Henry Bessemer to introduce what is known as the Bessemer process.

Jan 1, 1930

By Kavetsky A, Scott A

As well as breaking and moving rock, blast energy sets up a seismic wave in the ground which can cause significant damage to rock structures and buildings and disturbance to human occupants. This seismic ground vibration is potentially most damaging when its dominant frequency coincides with the resonant frequency of a structure, leading to high amplification factors between the input ground vibration and the resulting structural response. This paper outlines methods of identifying the resonant frequency of structures. It also describes a practical numerical method for the modification of blast designs to reduce the ground vibration energy in critical frequency ranges. The method is illustrated with two recent case studies.

Jan 1, 1990