Search Documents

By D Smith, D Reid, D Bradshaw, C Brough

The Merensky Reef at Northam Platinum Mine in South Africa is characterised by a high degree of variability with respect to reef elevation (difficult to mine), as well as mineralogy and texture (difficult to process). Development along strike and down dip of multiple reef types has led to unpredictable run-of-mine characteristics that pose problems for the mineral processing circuit at Northam. Following mining terminology, Normal, Transitional (NP2) and Pothole (P2) Merensky reef types can be defined, and this geometallurgical study aims to characterise and understand the relationship between their mineralogical characteristics and laboratory scale batch flotation performance. The plagioclase-rich NP2 reef ore is the easiest ore to process in terms of capacity for high mill throughput as well as flotation performance. The lack of very fine-grained disseminated sulfide textures in the NP2 reef ore results in better liberation characteristics relative to the Normal and P2 reef types. Consequently, chalcopyrite, pentlandite and sulfide recoveries are highest for the NP2 reef ore. The lack of ferromagnesian minerals in the NP2 reef ore also results in the recovery of the least amount of floatable gangue during flotation tests. The Normal and P2 reef ores are similar to each other, with an orthopyroxene-rich mineralogy with associated alteration minerals. The P2 reef is also characterised by the highest sulfide content and degree of pentlandite liberation. Chalcopyrite, pentlandite and pyrrhotite liberation is only significantly increased by a change in grind for the Normal reef ore. The change in grind, however, only significantly affects pentlandite flotation performance and overall froth stability for the Normal reef ore. However, for all three ores, a small change in grind has a detrimental effect on pentlandite flotation performance.

Jan 1, 2008

Factors influencing Cost, systems available for transporting minerals, particularly on land, and methods used for comparing costs are reviewed. A case study presents comparative costs graphically for coal haulage, assumed in Queensland, by 31-6" gauge rail, belt conveyor, 120 ton road train, slurry pipeline, and transmission of electrical energy by transmission line. The effect on comparative results of alternative methods of including initial capital and capital replacement costs is considered and approximate break-even points between systems, bearing in mind the assumptions taken, are discussed.

Jan 1, 1973

The Beaconsfield gold mine processing plant is a complex operation and utilises crushing, grinding, gravity gold concentration, sulfide flotation, bacterial oxidation, cyanidation and zinc cementation to recover gold from the partially refractory ore. This paper discusses the challenges, developments and advancements throughout the processing plant since start up, which have culminated in a 25 per cent increase in the mill throughput over the nameplate design and a concomitant gold recovery increase from 75 to 92 per cent. The improvements have been attained via advancements in mechanical integrity, metallurgical review, process control and operator training, resulting in the current operation producing over 630 000 ounces of gold to date.

Jan 1, 2007

Manganese ore has been mined from the Peak Hill Gold- field since 1948 and from the Pi'lbaraòGoldfield since 1954, and it is probable that some deposits- In and, near the Phillips River Goldfield will be mined at a future date', There are also several million tons of mariganiferous ;naterial which is too low in manganese. .co.ntent_ for . present requirements. The manganese deposits¦of Western Australia are mostly superficial. They hav' been formed during the Cainozoic Era by supergene enrichment ò6f Precambbrian: manganiferoius sediments, and by deposition from -solution on, or'in caves in, the Cain- ozoic land surface. The manganese in solution was derived from the weathering of Precambrian manganifer.ous s.edimexsts, None of the deposits are of hydrothermal origin, nor are they related to igneous rocks in any war, other than as ultimate source rocks. There is ho evidence-'t.o.:sugge,st that meta- morphism has been responsible for.the emplacement of any deposit. The tenor of the ore varies'aec'ording'to the quantity of gangue in the orebody and- also to the nature of the part- icular ore minerals. The main ore.mine.rals are the oxides pyrolusite and cryptomelane and the 'o'xide-silicate braunite. The main gangue minerals are hematite, limonite and quartz. The deposits of high grade oreò(-above.45 per cent Mn) range in size from 50 tons to many thousands of tons but most of them are in the 500-5,000-tons r .nge .

Jan 1, 1964

Grade control is an important factor in the on-going success of a mining operation. Grade control criteria will vary depending on the commodity being mined. Financial considerations determine the actual grade control criteria at any one mine site. Mining and metallurgical capital and operating costs are ultimately used in ascertaining cut-off grades employed in grade control. The metallurgical characteristics of the ore, and ultimately the equipment selection and design of the plant, are based on samples provided by the exploration geologist. Ore variability is an important factor in designing the process plant. Ore variations, outside of those catered for in the design, as well as large ore changes on a daily basis, will impact on the metallurgical performance, and hence the economics of a mining operation. Therefore good liaison between the grade control geologist and metallurgist will undoubtedly lead to a more consistent, and more profitable mining operation.

Jan 1, 1993

By C Yates, S Jobling, Z Y. Yang

The current trend in the UK towards the adoption of retreat longwall mining methods and the associated rapid development of the access drivages have exacerbated the environmental conditions experienced within these workings. There is a recognised need to improve the efficiency of the design and operation of mine ventilation systems in order to maintain an adequate environment and climate within these workings. Any improvement achieved in the quality, quantity and control of the delivered ventilation will assist in the provision of improved gas and dust dilution and climatic control. The paper presents an analysis of the psychrometric data recorded during the execution of a series of comprehensive climatic surveys conducted within two representative deep underground UK coal workings. The surveys were performed across two high production retreat longwall districts within UK Coal Ltd collieries. The surveys employed intrinsically safe psychrometric transducers and digital data-loggers to collect a continuous record of the mine climate over designated weekday production and weekend non-production periods. The transducers and data-logging units are capable of simultaneously measuring and digitally recording changes in the dry bulb temperature and the relative humidity at regular time intervals for extended periods of time.

Jan 1, 2005

By Ueki S

Underground coal gasification (UCG) is a promising process for obtai- ning energy from coal, which is either unmineable with current mining techno- logy or uneconomic to recover, using conventional methods, in the present energy market situation. There are several coal fields, which could become new coal reserves, if the UCG process were successfully applied. In the 1960's Japanese researchers made a number of basic studies and field tests into UCG, although not all of them produced favourable results. This paper reviews Japanese research on UCG. This includs basic studies into coal gasification using a small, tube reactor fed by air and oxygen, and also large scale model stu- dies(reactor size of 8.Om x 2.4m x 1.5 m). Field test results from Akabira colliery in Hokkaido and a feasibility study of power generation using UCG from a coal field in Hokkaido are also Presented.

Jan 1, 1987

By Melcher G

The challenge to the zinc industry is shifting from maximum metal recoveries to the environmentally safe processing of the ore concentrates. The main source of solid residues from hydrometallurgical zinc processing is the iron content of the concentrates. Unfortunately iron precipitates from leach liquors contain various compounds which cause them to be considered as environmentally unsafe, unless they have been cleaned in subsequent process steps. This calls for separating the iron from hydrometallurgical processing as early as possible. For this purpose a process has been designed to eliminate the iron directly after neutral leaching the calcine. This is being done by direct smelting the neutral leach residue with a cyclone/top blowing unit. The zinc is recovered from the neutral leach residue as a metal oxide to be recycled to the zinc process. The iron is converted to a slag, which is resistant to atmospheric attack. Key data of the integrated hydro-/pyrometallurgical process are presented as derived from pilot plant tests by cyclone smelting and top blowing the slag.

Jan 1, 1993

The state-owned Swedish company LKAB is one of the world's largest producers of iron ore. LKAB mines the greater part of its ore underground, and very high efficiency is vital if it is to compete successfully with open pit mines. Consequently, computers and OR are essential parts of the company's operations. This paper gives some examples of success- ful computer and OR applications at LKAB, coupled with some remarks on the costs and benefits of OR.

Jan 1, 1977

By Peck WH

For many years it was realised that the methods used for unloading concentrates at Port Pirie were inefficient and labour intensive, therefore, when a decision was reached to standardise the east-west rail link from Sydney to Perth, the opportunity was taken to consider entirely new schemes for the handling of concentrates at Broken Hill and Port Pirie. After considerable testing and investigation, it was decided to install a completely new concentrates handling plant incorporating a tippler at Port Pirieòto replace the previous long established methods of unloading and dis- tributing concentrates to the operating plant.and the shipping berths. To achieve this, wagons of concentrates from the various mines are marshalled in a set order at Broken Hill and conveyed to Port Pirie in 56-wagon trains. On arrival at Port Pirie, the wagons are checked and moved to a position where they come under the control of the automatic wagon marshalling equipment.

Jan 1, 1975

Petroleum exploration in the Australian arid zone has been proceeding at an ever-increasing pace, subject to financial fluctuations, since the 1960's. The impacts of petroleum exploration in the arid zone are less than they would be for corresponding operations in. e.g. a forest area: in this context, Australia is fortunate in that its major petroleum producing (and prospective) , basins are offshore or in the arid zone. In addition. the other major sources of impact in the Austrlian arid zone, namely pastoralism, tourism, and rabbits, tend to be concentrated around areas of particular conservation significance, whereas petroleum exploration is not. Despite this, the cumulative impacts of exploration are sufficient to have caused concern to government regulatory authorities and some sectors of the general public. Exploration is now subject to a range of environmental constraints with various degrees of legal enforceability. To enable exploration to continue without public opposition, the industry, and government agencies charged with regulating or supervising it, must demonstrate that the net benefits of exploration exceed net costs, including environmental costs. One particularly simple and cost-effective technique for increasing the net benefit/cost ratio of exploration is to reduce the net environmental costs by minimising and mitigating the impacts, both primary and secondary, of seismic acqisition. This is best achieved by a combination of preventive and restorative techniques: careful line positioning and low-impact (or zero) line clearance, coupled with simple rehabilitation of bladed lines. Line clearance without bulldozer blading - e.g. by rolling or simply pegging and trafficking, perhaps with tracked rather than rubber-tyred vibroseis - is one promising approach currently coming into use. Rehabilitation by grading soil banks ("windrows") back on to bladed tracks, though not yet in widespread use, has proved very successful in the limited areas where it has been applied to date.

Jan 1, 1987

This paper summarises the performance of the gold exploration industry in the Western World since 1970, with particular emphasis on the period 1985 - 2003. It identifies the number and size of major (ie >1 million ounce) primary gold discoveries made over this period by location and type of company. Estimates are also made of the likely contribution from smaller discoveries down to 0.1 million ounces. It also assesses the overall trend in the percentage of grassroot discoveries that are converted into mines, and the time taken to get them into production. By comparing the discovery data against total exploration expenditures it is possible to determine the average unit cost of finding a major gold deposit. It is significant to note that the average unit cost per discovery and per ounce of resource has tripled over the last 30 years. An attempt is made to determine the overall economic value generated by the industry. This is based on a detailed analysis of the rates of return and the Net Present Values (NPVs) of 109 major gold projects. After including an adjustment for discoveries not modelled, the NPVs are compared against the total amount of money spent on exploration to determine the value-to-cost ratio for the industry. Based on historical spot gold prices and tax rules, it is found that the return on investment for gold exploration in the Western World over the period 1985 - 2003 was around five per cent real after-tax. The returns achieved in the US and Australia was significantly higher than that for Canada. The returns also appear to have declined in recent years. With regard to the relative performance of junior versus major companies, the paper estimates that the junior sector accounted for 30 - 40 per cent of the total exploration expenditure, and were was associated with 34 per cent of the total number of major deposits, 27 per cent of the contained ounces and 25 per cent of the economic value found.

Jan 1, 2004

Roller seed screens were installed at The Broken Hill Proprietary Company Limited (B.H.P.) Whyalla pellet plant to replace vibrating screens on the green ball circuits. The installation of roller screens was justified by improving the sizing of the green balls. This improved sizing increased the yield of fired pellets produced from green balls thus decreasing the fuel consumption. The fired pellet sizing was improved also. This paper discusses the configuration of the roller screens installed at Whyalla, quality of green balls produced, advantages of roller screens compared with vibrating screens and future development of roller Screens.

Jan 1, 1984

By L Soares, W T. Hennies, F Fujimura

The engineering geological mapping of Metropolitan Area of Jopo Pessoa in the littoral zone of the Parafba State, northeast of Brazil, made possible the ambient characterisation for space using and its implications on the environmental resources. This region comes lately denoting an accented industrial growth and this work would help future projects of urban planning, distinguished by quick ground occupations for residential, industrial installations, farming, beyond mineral extractions. The mineral sector supplies material and substance demanded by industry and civil constructions, like as clay deposits, sands, calcareous rocks and mineral water. Many companies working there do not have the permission or inspection of ambient agencies for planned extractions of mineral resources. The consequences of this activity pass for the low profit of the reserves, bad uses of the sources, ground degradation, vegetation suppressions and physical impacts on landscapes, beyond noises and vibrations. These activities have causing accelerated alterations and transformations in the environment, compromising the sustainable development. It thus becomes clear that urgent solutions must be find to solve the problems with human interferences by closer inspection and management for disciplined use of its natural resources.

Jan 1, 2003

The resources industry is unique in that the finite nature of resource deposits requires a participant to be constantly locating and developing new ones to replace those that are depleted. An effective growth strategy that enables new project developments to be brought on line in time and within budget is therefore of fundamental importance to any mineral resources company. This paper seeks to identify the role of the development project in the company's overall growth strategy and the key performance criteria that a development project must achieve in order to allow a company to meet its growth objectives.

Jan 1, 1997

By C F. Prins, C LantuTjoul

Mineralisation in alluvial diamond or vein gold deposits is often hosted in trapping mechanisms. For instance, diamonds are nested in bedrock depressions such as gullies and potholes which were carved out by the sea long before the diamond deposition took place. Similarly, gold mineralisation can precipitate in the necks of a boudinage structure. In such deposits, the spatial distribution of the mineralisation is governed by the mutual arrangement of the trapsites and by the grade variations within each trapsite. Reliable estimates can be obtained only if they rest on a proper knowledge of both degrees of variability. This creates a challenging sampling problem, as during the exploration phase it is important to have a good global mean estimate to enable decision making towards the future. A similar problem occurs for local estimates at a later stage of development. To understand and manage the sampling for global means, specific sampling procedures are required based on an appropriate choice of sample support size and spacing. Estimates from such sampling campaigns should be unbiased, and the less variability they display, the better the sampling parameters. The performance and impact of sampling parameters are tested and compared on different simulated deposits.

Jan 1, 2005

During 1995 a catastrophic accident took place at the No 2 Vaal Reefs shaft in South Africa, when a locomotive fell onto a cage, causing the death of 104 people. The subsequent Commission of Enquiry found that the safety detaching hook had opened when hit by parts of the falling locomotive, detaching the cage from the rope and allowing the cage to drop 400 m down the shaft. It was believed that had the hook not detached, the rope would have been sufficiently elastic not to have failed, implying that many fatalities may have been avoided. In addition, the risk of accidental opening of hooks due to impact with smaller falling objects in shafts became a concern. This paper deals with a comprehensive statistical investigation that was performed to quantify this risk, establish acceptable levels of such risks and to derive criteria for the resistance of detachment hooks against accidental opening caused by impacts. The investigation involved a survey, dynamic finite element analyses and Monte Carlo simulations.

Jan 1, 2005

By Bennet A. G

As part of the construction of the Melbourne Underground Rail Loop it was necessary to construct two 7 metre diameter tunnels, each 100 metres in length, by shield driven excavation through an alluvial valley at Elizabeth Street. The tunnels had a primary support of bolted precast reinforced concrete liner blocks and were excavated with the aid of compressed air. The work was undertaken by the Tunnelling Group of the Melbourne and Metropolitan Board of Works as nominated sub-contractor to John Holland (Constructions) Pty. Ltd. The paper describes some of the problems associated with the construction of the above tunnels and the methods used to overcome them. In particular

Jan 1, 1981

By H. J. Glass, A J. Cornah

Improving the quality of the variogram helps to improve subsequent estimation and simulation processes. Two strategies for conditioning data prior to construction of the variogram are investigated using data from the Luce iron ore deposit in Canada. One strategy is the classic approach in which the deposit is subdivided into a set of structural domains. The domains are analysed individually and datapairs are recombined to produce a variogram. The second strategy is reconstruction of the deposit at an earlier stage of its history through unfolding. This involves transformation of the Cartesian coordinates into stratigraphic coordinate system. Improvement in the variogram quality, expressed in a decreased weighted deviation from a fitted model, is observed for both types of data conditioning. This indicates that, for the Luce deposit, application of data conditioning could also help to inform the selection of sampling locations.

Jan 1, 2006

By A J. Moore

To control the airblast from blasting to regulatory limits at environmentally sensitive sites near the Collinsville Coal Mining Operations, it has been necessary for Thiess Mining to incorporate a wavefront reinforcement analysis model in the predictive environmental airblast design. Controlling airblast from cast blasting 70 m high faces with 2000-3000 kg of explosives per hole within 700 m of houses presents a considerable challenge to the blasting personnel. This paper describes the model used and summarises the results of an investigation designed to quantify the increase in airblast indicated by wavefront reinforcement diagrams to further calibrate the model for future prediction.

Jan 1, 2004