Search Documents

By P. Zhang, K. Liu, L. Ou

"The strength and mechanism of Portland cement prepared from stone coal vanadium slag were studied in this paper. Initially, the slag was used as silicon raw materials to prepare clinker. By blending the prepared clinker with gypsum, waste, and fly ash, a series of different grades cement got well prepared. All of performances of the cement were up to the requirements of China’s national standard. The hydration products and microstructure of cement were identified and analyzed by X-ray diffraction and scanning electron microscopy. With the comparison of cement hydration characteristics at different ages, the strength formation mechanism of cement was clarified. The experimental results suggested that adding the fine materials (mainly waste and fly ash) to replace part of clinker would accelerate cement hydration, as it provided additional surfaces for the nucleation and growth of hydration products. And the hydration products were similar to ordinary Portland cement, mainly containing the amorphous calcium silicate hydrates (C-S-H), acicular ettringite (AFt) and portlandite (CH). With hydration time increasing, the hydration products continuously covered the cement particles, resulting in a thicker surface layer. As a result, it gradually condensed into a dense structure block with small pores and smooth surfaces, which led to higher strength. In conclusion, using the vanadium slag to prepare Portland cement can realize the utilization of solid mineral wastes, which will bring huge ecological and economic benefits.INTRODUCTIONWith the development of China’s mining industry, more and more mineral waste residue is discharged every year. These solid wastes cause varieties of resources and environmental problems on people’s living area. While at the same time, the demands of cement are increasing with the remarkable development of the construction industry. Thus, in recent years, utilization of proper solid waste to prepare cement has become an efficient way to deal with the solid mineral wastes problems (Boncukcuoglu, Kocakeri?M, & Tosunoglu, 2002; Simatupang, Hanafi, Purwasasmita, Imran, & Pane, 2012; Tsakiridis, Papadimitriou, Tsivilis, & Koroneos, 2008; Yun, Yong, Choi, Lee, & Lachemi, 2009)."

Jan 1, 2016

By C S. Stevens

This paper describes the problems encountered and the steps taken to solve them in milling an ore containing relatively large amounts of pyrrhotite. A complex and greatly lengthened flotation circuit was required to recover the pyrrhotite. A very low pH had to be maintained in the cyanide circuit in order to get good recovery of the gold and maintain reasonable cyanide recovery. Introduction D ELNITE Mines Ltd., a gold mine situated about 5 miles by road south and east of the town of Timmins, Ontario, is serviced by two shafts. No. 2 shaft extends from surface to the 2875-ft. level, and No. 3 shaft, an internal winze, extends from the 2875-to the 5275-ft. level. No. 2 shaft was stopped at the 2875-ft. level because of a heavy band of chloritic schist which necessitated a drive to the north for 1000 feet, where No. 3 shaft was sunk. The latter bottomed in the schist at the 5275-ft. level. From the 2500 to the 2875-ft. level in No. 2 shaft, the ore was

Jan 1, 1965

By John T. Whetton

"FROM 1850 when the annual production was around 50 million tons, coal output in Great Britain expanded rapidly to 225 million tons in 1900 and 287 million tons in 1913. However, during the First World War, countries which had previously bought large quantities of coal from Britain sought other sources of sup-ply or developed their own coal re-sources. Thus from the record figure of 73 million tons exported in 1913, Britain's coal exports declined until in 1938 they stood at 39 mil-lion tons. An important reason for this was the development of oil engines for marine propulsion. Today, nearly all the navies and mercantile shipping in the world have turned to oil engines. Sometime in the future, however, it is reasonable to expect nuclear power to replace oil.During the Second World War, coal output in Great Britain and manpower at the mines were reduced considerably and in 1.945, 175 mil-lion tons were produced by 709,000 miners. Exports were meagre, only 8.""7 million tons went to foreign consumption. During the severe winter of 1947, inland demand for coal exceeded production and exports were prohibited. Even importation of coal was required to meet inland demand. These were years when the coal industry of Great Britain made immense efforts to secure maximum output irrespective of economy. The energy needs of Great Britain appeared insatiable; but had it been possible to export, the nationalised mining industry could have made huge profits as there was a world shortage of coal. However, home needs were considered to be the priority and many overseas markets were lost. Other producers moved in and secured long-term contracts. Not only was the British export market lost, but also the nationalised industry had to sell the imported coal at the same prices as home-produced coal and suffered losses up to of:3 per ton. Bence, at a time when the National Coal Board might have ac-cumulated a reserve fund to cope with less prosperons times, it was having to spend large sums of money securing sufficient coal for inland consumption. This was a time when intensive efforts in the mining industry, comparable with those of many industries and establishments inclusive of the armed services during the war, would have produced a greater amount of coal and have been of immense value to the country as a whole."

Jan 1, 1960

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to maximise health and safety performance in the mining industry through implementing continual improvement in management of major unwanted events. A comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This will be extended to outburst, coal burst and bumps, interface displays and controls, tailings dams and inrush in 2013. RISKGATE presents substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry. All major Australian mining companies are contributing topic experts to this broad industry initiative. In the first 24 months, nine coal mining companies nominated over 80 different experts who contributed over 400 days of individual time to the knowledge capture workshops. RISKGATE is the largest single Australian Coal Association Research Program (ACARP) occupational health and safety (OHS) initiative to date.

Aug 1, 2013

By Roland B. Hoag, Roger G. Webber

Sulphate concentration in groundwater is a good measure of the extent of oxidation of sulphides, provided that sulphide minerals are the primary source of the sulphate. A study was conducted near the Eustis Mine in Quebec to determine where and how the sulphate in groundwaters originated. Atmospheric precipitation is the only source of sulphate other than oxidation of sulphides, and in this study area it is equal to 0.01,. millimole per litre. The oxidation of sulphides can be divided into subsurface oxidation (mainly inorganic processes) and surface oxidation (including both organic and inorganic processes) . The maximum sulphate concentration due to subsurface oxidation of sulphides depends on the solubility of 0 2 in water and is 0.25 millimole per litre. Surface oxidation is, therefore, responsible for any amount greater than atmospheric plus subsurface contributions (0.29 millimole per litre). Surface inorganic oxidation occurs in waters with a pH greater than 15 and is controlled by the kinetics of the oxidation processes. Organic (bacterial) surface oxidation is dominant only in acid (pH< 1.5) waters. The bacterial action accelerates the oxidation of sulphides, and large quanttties of sulphate may be introduced into solution.

Jan 1, 1976

By J. A. Allan

OCCURRENCES of salt in Alberta have been mentioned and described by the writer in 1929 (l) and by Cole in 1930 (2). Brine springs occur at a number of places along the valley of Athabaska river north of latitude 56 degrees, and also on the south margin of Salt prairie, twenty-five miles west of Fitzgerald in the vicinity of the 60th parallel of latitude, which is the boundary between Alberta and the Northwest Territories. These salt springs were visited by Sir James Richardson in 1820, and in the same year D. W. Harmon stated that " ... clown Salt river there are several places where almost any quantity of excellent dean white salt may be taken with as much ease as sand along the seashore" (3). One hundred years later, in 1920, when the writer first visited these springs, the "dean white salt" which had accumulated about the springs was about 400 tons ( 4). This paper deals with a thick deposit of rock-salt which has been proved by drilling in the vicinity of McMurray. Particular attention will be given to a well drilled at Waterways early in 1936 by Industrial Minerals, Limited, when a continuous bed of rock-salt was penetrated with a thickness of 199 feet. As this paper is being presented, a salt plant is being completed and a production well is being drilled at the plant. < is salt deposit is in the vicinity of McMurray, close to the junction of the Clearwater and Athabaska rivets, in township 89, range 9, west of the 4th meridian. McMurray is about 240 miles northeast from Edmonton. As shown on Figure 1, Clearwater river, which rises at Methy portage, in Saskatchewan, enters Athabaska river at McMurray. Some three miles above the mouth of Clearwater river, the Hangingstone enters from the southwest. Waterways, where the latest salt development has taken place, is situated at the end of the Northern Alberta railway, a distance of 304 miles from Edmonton. This railway reaches the bottom of the Clearwater valley at Draper station, about 3 miles east of Waterways and near the mouth of Deep creek. The Draper bituminous sand plant is approximately half a mile east of Draper station. About one mile south of the townsite of McMurray, Horse river enters the Athabaska from the east.

Jan 1, 1937

By D. J. Zuliani

A mass and energy balance for a modern electric arc furnace ("EAF") indicates that about 70% of the process energy losses are contained in the off-gas as chemical energy in the form of uncombusted CO and H2 and as thermal energy. Given the magnitude of the off-gas energy losses, improved EAF energy efficiency needs to focus first on controlling furnace practice to maximize "in-EAF" energy utilization and second, on recovering residual energy in the off-gas existing in the fume system. This paper focuses on the application of off-gas analyzers, sensors and process models to control and optimize "in-EAF" energy utilization efficiency. The paper will also discuss the application of heat recovery technology to EAF steelmaking.

Jan 1, 2015

By George J. Simandl, Donald F. Gunning

At the beginning of the 20 century, British Columbia produced a wide variety of quality dimension stone products for both domestic and foreign markets. The industry flourished until the 1930s when most of the producing quarries closed as a result of the Depression. During the 1990s, British Columbia experienced the resurgent North American dimensional stone production trend. The industry benefited from increased prospecting activity and from substantial new investment in processing equipment, particularly in the granite sector. These activities resulted in new quarry developments, the reopening of abandoned quarries such as on Granite and Fox Islands <www.quadrastone.com>, and a renaissance in downstream value-added activities. British Columbia has reestablished itself as an important, reliable and innovative source of high-quality stone products.

Jan 1, 2001

By Gyeonghye Moon, Inhyeok Choi, Jyothi Rajesh Kumar, Jin-Young Lee

"This paper deals with the recovery of the tungsten and vanadium from spent SCR catalyst leach liquors by different hydrometallurgical methods. The first part consists of pressure leaching of spent SCR catalyst using caustic soda followed by metal recovery by liquid-liquid extraction. In a leaching process, the following experimental parameters were tested and optimized: NaOH, particle size of feedstock, temperature, and solid to liquid ratio. The optimum condition for leaching of tungsten and vanadium was under the following conditions: NaOH 3 mol/L, temperature 250°C, particle size <300 µm, and solid to liquid ratio 0.4. From these optimum conditions in this experiment, the dissolution efficiency of vanadium and tungsten was 91.5and 87%, respectively. Liquid-liquid extraction following commercial extractants were tested: TBP, Cyanex 272, D2EHPA, Aliquat 336, Primeme JM-T, Alamine 308, Alamine 304-1, and methyl-tri-octyl-ammonium chloride. The conditions for both valuable metal recoveries were optimized.INTRODUCTIONSelective Catalytic Reduction (SCR) catalyst has become the most effective to reduce nitrogen oxide (NOx) emissions from stationary segments such as power plants and waste incinerations around the world due to the reinforcing regulatory trend and emerging environmental issues (Forzatti, 2001; Spivey, 2002; Li et al., 2011).Currently, the most widely used SCR catalyst is V2O5-WO3/TiO2 system due to its great catalytic properties (Li et al., 2011; Marshneva et al., 1995; Marbergeret al., 2015). In general, the composition of the SCR catalyst used in the stationary application is 0.5 to 1 wt% of V2O5and 7 to 10 wt% of WO3(Marberger et al., 2015; Chen &Yang, 1992, Vuurman et al., 1991; Alemany et al., 1991). Currently spent SCR catalysts are treated as waste and disposed of in landfills. This causes a lot of waste of secondary resources of vanadium and tungsten. In terms of industrial value of vanadium and tungsten (Gupta &Mukherjee, 1990; Moskalyk &Alfantazi, 2003) and reduction of pollutant emissions, it should not be disregarded for their recovery for their material recycling from spent SCR catalyst. However, investigations for recovery of metal values from spent SCR catalyst has been rarely carried out."

Jan 1, 2017

By E. L. Bruce

Introduction The Outokumpu copper mine is situated in eastern Finland, 50 kilometers west of the city of Joensuu or 225 kilometers directly north of the city of Viborg (Viipuri), which is situated at the eastern end of the gulf of Finland (Figure 1). The ore-body was discovered in 1910 by Dr. Otto Trüstedt after two years of careful, scientifically-directed, search. During the early period of development of the mine, the ore was treated locally and the copper re-covered by an electrolytic process. Now the ore is concentrated by tables and by flotation. The concentrates are shipped to Germany for refining. In 1929 the mine produced 150,000 tons of ore from which between 20,000 and 25,000 tons of flotation concentrates containing 20 per cent copper were produced. Profits in 1929 were approximately half a million dollars, but the present price of copper will affect very seriously the profits for 1930. The ore reserves are given as between 7 and 8 million tons (1). The grade of ore is stated to be 4 percent to 6 percent copper, with a little zinc.

Jan 1, 1931

By L. Tong

The nickel laterite ore is composed of soft and hard minerals, and nickel distributes preferentially into the soft mineral rather than in the hard. Selective comminution of saprolitic and goethitic nickel laterites is investigated to upgrade nickel into the fine fraction using stirred milling. The optimal selective grinding conditions were determined through a kinetic study and the limit of selective grinding and nickel upgrade was analyzed. The breakage rates of minerals, grinding time, and the weight ratio of soft and hard minerals in the feed play an important role in selective grinding. A small breakage rate on hard minerals and a large breakage rate difference between the minerals are optimum for selective grinding. The soft mineral grade decreases with grinding time and the optimum grinding time is a trade-off of the soft mineral upgrade and recovery. The minerals weight ratio determines the limit of selective grinding. The effect of nickel upgrade is determined by both the conditions that influence selective comminution and the nickel grades in both the soft and hard minerals. The nickel grade in the soft mineral determines the limit of nickel upgrade.

Jan 1, 2015

By R W. Drybrough

The program to increase production at Sherritt Gordon&apos;s Lynn Lake property, which began in 1956, included increasing the rope speed and the horsepower of the ore hoist at the "A" shaft. Because of the limited power sup-ply from the two 7,000-hp. hydroelectric plants, and the ? 3,600 hp. predicted for the combined hoisting requirements of the three production shafts, it was considered desirable to lessen the impact of this type of load on the relatively small power system by equipping all future hoisting arrangements with Ward Leonard direct-current drives. The manually operated 8-by 4-ft. hoist at the "A" shaft had a rope speed of 1000 f.p.m., and was driven by a 385-hp., 380-r.p.m. wound rotor motor with liquid rheostat control. This A.C. drive was replaced by a semi-automatic Ward Leonard direct-current drive with a 515-hp., 566-r.p.m., shunt wound motor, providing a rope speed of 1,500 f.p.m. During several months preceding the con-version, all possible preparations were carried out to keep the changeover period to a minimum, and this resulted in a total shutdown time of twelve days. The capability of the "A" Shaft hoist was increased from 109 tons per hour to 134 tons per hour, and both mechanical and electrical maintenance were reduced considerably. The total cost of the conversion amounted to $130,000. The hoistmen who had been required for the manual A.C. drive were transferred to the new Farley shaft, and the reduction in operating labour costs of the "A" Shaft hoist

Jan 1, 1965

By T. Kerr, C. Mattich, J. Wilson

"In refractory gold concentrates, gold is occluded in sulphide minerals preventing efficient cyanide leaching. Hence, roasting is used to oxidize sulphur and organic carbon, the latter being necessary to minimize recovery loss through the preg-robbing effect. In 2009, Outotec commissioned the circulating fluidized bed roaster at Syama gold mine in Mali. Since 2013 Resolute and Outotec have been implementing improvements to the roaster performance with the capacity increasing from 8000 t/month in 2013 to above 13,000 t/month in 2016, while achieving a residual sulphide sulphur and organic carbon contents of below 0.1 wt.% and 0.4 wt.%, respectively. Thus a gold recovery in the CIL of above 90% is attained. In 2016, Outotec audited the Syama roaster. The analysis resulted in the Low Carbon Roaster (LCR) upgrade concept which (i) allows re-processing of calcine dust from the spray cooler and ESP after pelletization and (ii) allows the roasting of a further fine-organic carbon rich feed, i.e. de-slime circuit tailings. The LCR upgrade aims to reduce organic carbon to <0.2 wt.% and increase roaster-leaching gold recovery by >3%. Project development included extensive testwork. The LCR process is expected to become operational during FY 2019.INTRODUCTION Double refractory sulphide ores exhibit the characteristics of gold locked within pyrite grains, in the presence of preg-robbing natural (organic) carbon. Hence, to achieve high recovery during subsequent processing steps, i.e. cyanide leaching, oxidation of sulphide sulphur is required, producing a porous calcine by way of a roasting step. This allows for the gold contained within the pyrite grains to be accessible during cyanide leaching. Furthermore, it is necessary to oxidize the organic carbon. Oxidizing the organic carbon is essential as gold recovery loss occurs as a result of gold-cyanide complexes being adsorbed on organic carbon, this phenomenon is termed as preg-robbing (Miller et al., 2016). The gold absorbed on the organic carbon is lost, reporting to the tailings stream. Hence, the aforementioned oxidation of sulphide sulphur and organic carbon is the process goal. Nonetheless, the latter must occur at a controlled temperature which is concentrate/ ore specific, since the pores of the produced calcine should not sinter, as this makes the gold contained in the calcine less accessible during leaching, leading to gold recovery loss. The tight temperature control requirement is a decisive factor in the choice of a Circulating Fluidized Bed (CFB) as the roasting reactor, due to the excellent mixing characteristics of the CFB which results in temperature homogeneity of (+/-10°C). Roasting of double refractory ores, as described above, can be included in the flowsheet after comminution and grinding, a process termed as whole ore roasting, or by including a flotation circuit termed as concentrate roasting. Roasting the flotation concentrate results in less solid flow, increased sulphide sulphur grade and organic carbon content resulting in a higher heating value and higher gold content. A typical composition of the Syama ore and concentrate is given in Table 1. Ore average values presented correspond to the period 2015, while concentrate values are typical for the flotation performance throughout the period 2012–2015."

Jan 1, 2017

By R. Elliott, C. A. Pickles, J. Peacey

As the nickel sulfide ore deposits become decreasingly viable as a source of nickel metal, increasing attention is being paid to the exploitation of the nickeliferous laterite ores. Attempts to produce a high grade ferronickel concentrate from these ores by pyrometallurgical methods face several challenges, in particular the selective recovery of the highly disseminated nickel from the reduced ore. The current work explores strategies for maximizing the size of ferronickel particles formed in order to improve the selective recovery of the ferronickel by magnetic separation. The effect of various coal, elemental sulphur, pyrite and sodium sulphate additions on ferronickel particle formation and size at 1000°C have been investigated. It has been observed that increased coal additions leads to a moderate improvement in the size of the ferronickel particles, while the presence of any sulphur bearing reagent leads to a significant increase in particle size. The retention of sulphur in the reduced material has also been studied, showing sodium sulphate has the highest retention, followed by pyrite and then elemental sulphur. An inverse trend was observed in the efficiency of sulphur retention on the basis of residual mass of sulphur per unit mass of reagent added.

Jan 1, 2015

By O. Herstad, J. M. Toguri, K. Grjotheim

DURING the last three years, investigations on the aluminum reduction of magnesium-bearing compounds have been initiated at the Institute of Inorganic Chemistry, The Technical University of Norway. The results of these investigations are reported in this paper. Very little information exists in the literature on the reaction between magnesium compounds and metallic aluminum. The available information itself is conflicting, and, to clarify the existing discrepancy, the reactions between aluminum and magnesium oxide (MgO), caJcined dolomite (CaO . MgO) and olivine (Mg2SiO.) were studied. The logical approach for the study of these reactions between condensed states with the formation of a gaseous phase is, ( 1) the measurement of the equilibrium vapour pressure of the gas, in this case magnesium, associated with the respective reactions and, (2) the identification of the end products of the reaction in order to establish the re-action scheme.

Jan 1, 1962

By L. Bos

The availability and reliability of large grinding mills and their Gearless Mill Drives (GMDs) are of paramount importance for the grinding process. Although GMDs have been in service for decades, and are known for their operational efficiency (reliability and robustness with reduced operating cost per ton), compared to conventional drives, in the last decade due to certain reasons some failures led to serious unscheduled shutdowns and significant insurance events. The majority of these notable "insured" failures have happened on GMDs installed on relatively large mills, as the financial impact of a failure is proportional to the through-put of the mill. Despite the occurrences of these events, as mining operations are driven by lower ore grades and the ability to continue reducing operating costs per ton, the trend for having larger mills is still very present and there is no reason why this trend should not continue. It is obvious that if not handled correctly, the possibility of large value GMD loss events, coupled with the continuing increase in mill size or required availability and reliability targets, could potentially lead to major conflicts as it becomes difficult for the insurance companies to judge the risk and hence may result in hesitation to insure these grinding circuits. This paper will not only describe the conflicting situation from both an insurer&apos;s perspective and from an equipment supplier&apos;s perspective, but also how these conflicting challenges can be successfully mastered. It has to be noted that not only the mining companies themselves, but also their insurance companies and the involved equipment suppliers have a common interest: to reach the highest availability and reliability in order to avoid or at least minimize unscheduled shut down times, and most importantly prevent unplanned events that result in extended production stoppages or reductions in through-put of GMD driven mills. From the very beginning onwards, the complete service concept together with emergency plans must be integrated on every level in the design of the grinding circuit. This approach must be implemented continuously and without compromises by all involved parties during all following stages, such as basic design, detail design, manufacturing, quality inspection and testing, packing, transportation, storage, installation, commissioning, operation and maintenance. The concept of formal risk analysis related to mill operations, maintenance and spare parts strategies must be an integral part of mining companies? decisions related to the selection for installation and continued use of large mills powered by GMDs. The service concept in place for operating mills shall also have a clear focus on very early detection of any abnormalities, so that the risk can be mitigated and unscheduled shutdown times avoided. However, if a major failure occurs, then procedures and tools shall already be available in order to ensure that production impact is minimized.

Jan 1, 2012

By Finley A. Campbell

THE Quemont and Horne mines are located at Noranda in north-western Quebec. As shown in Figure 1, the Noranda area lies between the Cadillac-Bouzan fault zone on the south and the Porcupine-Destor fault zone to the north. Both of these major structural lineaments appear to be geometrically, and possibly genetically, related to the Grenville Front. The regional geology has been discussed by Wilson (12), Cooke et al. ( 2), and others. The geology in the Noranda vicinity, as compiled by Dugas and Gilbert ( 3), is shown in Figure 2. The Cadillac-Bouzan fault zone separates the dominantly Temiskaming-type sediments in the south from the Keewatin-type canic rocks to the north. These volcanics, which vary in composition from rhyolite to andesite, form a broad anticlinorium with a general eastward plunge. A succession of dioritic stocks, sills and dikes have been mapped in the area. The principal granitic rock masses include the Powell, Flavrian and Dufault stocks.

Jan 1, 1962

By B. K. Ayres

Modern management of uranium mine or mill waste storage facilities (WSFs) often requires that they be remediated or decommissioned with a cover system. In addition to creating a self-sustaining landscape that supports the end land use, cover systems are intended to reduce long-term risks to human and ecological receptors from the stored waste to acceptable levels. The performance and longevity of a cover system will be strongly influenced by the features or shapes of the WSF final landform. Hence, cover systems and landforms must be thought of as an integrated design. Based on the author’s experience, the most important elements of the design process for maximizing the potential of WSF final landforms / cover systems being sustainable over the long term are noted in this manuscript. Several key items that must be considered and addressed during the planning phase of constructing a WSF final landform are also described. Various methods for monitoring performance of a WSF final landform are also reviewed. Key aspects associated with decommissioning a tailings WSF and waste rock pile at the former Cluff Lake uranium mine in northern Saskatchewan are included to illustrate many of the practical insights provided in this paper.

Jan 1, 2020

By K. G. Chipman

IN 1936, the Department of Mines and Resources was formed by the amalgamation of the former Departments of Mines, Interior, Indian Affairs, and Immigration. In the amalgamation, the Geological Survey and the Topographical Survey became the major divisions of the Bureau of Geology and Topography, which is a part of the Mines and Geology Branch which, in turn, is a part of the Department of Mines and Resources. The Topographical Survey was formed by combining the former Topographical Division of the Geological Survey and the air and ground mapping sections of the former Topographical and Air Survey Bureau of the Department of the Interior. The latter organization, previous to 1933, had been known as the Topographical Surveys Branch of the Department of the Interior. The amalgamation of 1936 definitely placed on the Topographical Survey the responsibility for the original mapping required for the development of our natural resources. The war has brought upon us the situation where all work has had to be in the furtherance of the war effort. With decreased staff and limited appropriations, the mapping on those scales which are directly concerned with the natural resources has been confined to the search for oil and strategic minerals. The reconstruction period will produce a different situation, with different problems. The past is behind us and it is necessary to prepare for the future. First, we should consider briefly a few general principles in the making and using of maps, then take stock of what we have, see what the needs are, and consider how we are to meet these needs.

Jan 1, 1944

By Charles Camsell

At the Annual General Meeting of the Institute in 1924. I endeavoured to present the position held by the mineral industries in the commercial life of this country. The facts and figures were presented at that time in a detached way. Since then, however, I have made some attempt to analyze them in order to determine the causes for that position and to draw some conclusions as to the future of the mining industry. As everyone knows, our trade figures are very often used in political discussion, especially in discussion of tariff policy. It would be entirely out of order for me to say anything touching the tariff issue and I want to have it clearly understood that, in my opinion, the material I am about to present contains not a single statement or conclusion which anyone would be warranted in using as an argument for either a lower or a higher tariff or for tariff changes of any kind. As a starting point, let me re-state, very sketchily, Canada&apos;s general situation in external trade. In the last calendar year, 1924, we sold Canadian merchandise of all kinds to other countries to the value of $1,045,000,000 in round figures. Our purchases abroad reached about $893,000,000. Thus our sales exceeded our purchases by roughly $152,000,000. In other words, we had what is known as a &apos;favourable balance of trade&apos; - one of the biggest favourable balances we have ever had in our history. The proceeds of our sales of Canadian products enabled us to meet the bills for all our purchases of foreign commodities and, in addition, placed a large surplus to our credit with which to offset our interest charges and other obligations abroad.

Jan 1, 1925