Search Documents

By C. D. M. Chisholm

IN discussing stope filling, or backfilling, at the Sullivan mine, at Kimberley, B.C., a brief description of the problem will first be presented. The Sullivan orebody is a replacement in quartzite, with the ore con-forming, for the most part, with the bedding. The dip of the vein, apart from local irregularities, averages about 15 degrees near the outcrop in the southwest section of the mine, and steepens to almost 40 degrees at the northeast end of the mine. The thickness varies from a few feet to over 200 feet at the widest sections. The mineable length along the strike has averaged about 4,000 feet between the 4,600 and 3,900 levels-the section under discussion in this paper. To date, 28,000,000 tons of ore have been mined by the room-and-pillar method. Prior to 1930, all ground opened up had been supported by ore pillars, left during mining operations. From that time, the recovery of the ore from these pillars has been given serious consideration. Backfilling, as being carried on today, is the result of this study and is being done for two reasons: (1) to allow extraction of the ore pillars, and (2) to minimize subsidence of the hanging-wall rock, except where forced caving is found desirable. PRELIMINARY DEVELOPMENTS LEADING TO BACKFILLING When the Sullivan orebody was first opened up, early in the century, there appeared to be low-grade sections of the vein sufficient in extent to serve as permanent support for the roof. However, as mining extended into sections of the vein that showed continuous ore over greater areas, wooden cribs, filled with waste and low-grade ore, were erected. In some stopes, these cribs were as large as 40 ft. by 100 ft. in plan and from 50 ft. to 60 ft. in height, but it was soon realized that this method of support was inadequate. As mining progressed, it was found necessary to leave ore pillars, which eventually became the sole system of support. At first, these pillars were left at irregular intervals, but later they were laid out at definite locations on the mine plans, and these locations were adhered to as closely as mining would permit.

Jan 1, 1941

By P. E. Weidmark

"CANMET InformationPART 1-Published PapersAsmis, H. W., ""The dynamic response of caverns in discontinuous rock""; Proc 22nd U.S. Symposium on Rock Mechanics, Cambridge, Mass, June 1981, 272-277; 1981.Austin , M.W., Bray, J.W. and Crawford, A.M., ""A comparison of two indirect boundary element formulations incorporating planes of weakness"" ; Technical Note; Int J Rock Mech Min Sci Geomech Abstr; 19:339-344; 1982.Barrett, J. R., ""Applying geotechnical theory to underground metalliferous mining""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 210-222; 1983.Barron, K., Wright, P.L. and Smales, T., ""Guideline s for the design of coal pillars in the No .4 seam at Mclntyre Mines Ltd ., Grande Cache, Alberta""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of A IMMPE; 559-578; 1983.Bauer, A., ""Wall control blasting in open pit mines""; Mining Engng; 34:155-158; 1982.Bieniawski, Z.T., "" Improved design o f room-and-pillar coal mines for U.S. conditions""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 19-51; 1982.Blackwell, G.H. and Calder, P.N., ""Practical aspects of wall stability at Brenda Mines Ltd., Peachland, BC""; 3rd Intnl Conf on Stability in Surface Mining; Vancouver, BC, June 1981; SME-A1ME; 3:573-608; 1982.Blake, W., ""Microseismic monitoring for underground stability "" ; Proc 1st Intnl Cont on Stability in Underground Mining; Vancouver , BC, August 1982; SME of AIMMPE; 272-294; 1983.Brawner, C.O., ""Stabilization of rock slopes"" ; 3rd Intnl Conf on Stability in Surface Mining; Vancouver, BC, June 1981; SME-AIME; 3:289-310; 1982.Bridges, M.C., ""Review of open stope mining in Australia""; Proc 1st lntnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 813-828: 1983."

Jan 1, 1983

By C. Dodds, R. S. Ferrari-John, The University of Nottingham, G. Dimitrakis, J. Katrib, A. R. Batchelor

"Sorting technologies have the potential to reduce energy use in comminution by rejecting uneconomic ore before feed material enters the mill. However, a major challenge for sorting porphyry copper ores is providing a basis of discrimination between valuable and non-valuable fragments, due to their complex mineralogies and textural features. Microwave heating in combination with infra-red detection (MW-IR) has been shown to provide upgraded feedstock for certain ores at bench scale. Selective heating of copper sulphide minerals compared to the gangue leads to an increased thermal response for valuable fragments, providing the basis for sorting.Rapid scale up of MW-IR from bench scale to a 100 t/h continuous pilot plant facility has been facilitated by the design of microwave choking structures to allow continuous operation at industrially meaningful throughputs, whilst meeting health and safety and electromagnetic compliance standards, and the integration of materials handling with electromagnetic systems.Laboratory batch testing on a pilot scale microwave system has been undertaken to investigate the thermal response of copper ores under industrial conditions, at microwave energy inputs up to 1 kWh/t. These results provided the operating window and recommended test conditions for the continuous pilot plant. Sortability curves predicted in the laboratory are in good agreement with separations achieved during continuous pilot plant operations. The potential microwave sortability of a number of ores has been studied, allowing informed decisions to be made about potential ore candidates based on mineralogy. Future development of the technology will be underpinned by the creation and validation of scale up concepts for 1000 t/h operations. Understanding the value proposition for individual sites/applications will be central to unlocking the potential economic and environmental benefits of microwave sorting."

Jan 1, 2016

By Michel Carreau

Presentation topic Introduction to Renewable Power in Remote Mining Industry Trend What are the Challenges and How to address them Acceptability (Management Buy-in) ? RP not core business to mining company Significant upfront costs Project Risks - Technological and Delivery Wind and solar power variability Operating hybrid power (Operator Buy-in) Conclusion Introduction ? RP at Remote Mining Sites Mining Project Cost Energy represents 25% of mining project CAPEX Energy represents 25% of OPEX Diesel, HFO, ? cost : 30+ cents/kWh RP - Proven technology - Excellent track record ?Wind (20 years), Solar PV (10+ years)? Hundreds of GW installed ?Reliable, High availability, very small OPEX. ?Wind/Solar cost : 15 to 22 cents/kWh (with good resource) ?Potential 10% to 20% Reduction in net cost of energy ?Price certainty for 20 to 25 years

May 1, 2013

By D. M. Rippley

THE St. Lawrence Seaway Project ranks with the greatest engineering undertakings of all time. A summary of major materials going into the construction of this project, shown in Table I, will assist in an appreciation -of this fact. These data relate to Seaway construction only, and it should be remembered that two large-scale power projects are in the construction stage on the St. Lawrence river concurrently with construction of the Seaway. A project of such magnitude as the Seaway would attract widespread interest even if it were being constructed in a remote area. The fact that it is located in a heavily populated and developed section of both Canada and the United States has done much to enhance this interest, and in many ways complicates the problems confronting the engineer in the design and construction phases. Many consider the St. Lawrence Seaway to be a new idea that has developed within the past decade - such is far from the fact, because the St. Lawrence River canal systems have existed for more than a century, and the Seaway Project is but a new, larger, and more efficient version of a continually expanding facility.

Jan 1, 1957

By G. P. Kundargi

India is one of the fastest growing economies in the world. The role of the Iron & Steel industry is very important for the development of the country. Iron and steel are among the most important components required for the infrastructure development of the country. This is one of the fastest growing sectors. The demand drivers for the Indian Iron & Steel industry are increase in the activities of the manufacturing industry and infrastructure development. Indian Iron & Steel industry with its strong forward and backward linkages contributes significantly to overall growth and development of the economy. The industry today directly contributes 2% of India?s Gross Domestic Product and its weightage in the official Index of Industrial Production (IIP) is 6.2%. Manganese is a main ingredient for production of steel. Almost 90% manganese is being utilized by the steel industry worldwide. Globally, there is no substitute for manganese as on date. There is huge gap between demand and production of manganese ore in the country. To meet this demand gap and to support for growth of national economy, MOIL Limited (formerly Manganese Ore India Limited), a Government Enterprises, producing annually around 1.1 million tonnes (mt) of manganese ore and value added products, has geared up with various infrastructural activities to increase the present production capacity of 1.1?1.5 mt in 2016?2017 and 2.2 mt in 2020?2021. The paper deals with the technological improvements and infrastructural development activities of MOIL; this will help MOIL to become the market leader in manganese ore production globally in the coming years.

Aug 1, 2013

By Harry J. Cain

Introduction The property of Pioneer Gold Mines of B. C., Limited, is located in the Lillooet mining district of British Columbia, on Cadwallader creek, 54 miles distant by motor road from Shalalth, a station on the Pacific Great Eastern railway. Milling by the present Company was commenced in 1924, a small amalgamation plant, consisting of a crusher, Bryan mill, and plates being operated until 1928. Tailing from this plant was impounded and later treated in the 100-ton continuous counter-current decantation cyanide plant which was erected during 1927-28 and placed in operation during May of 1928. A second cyanide plant, employing continuous counter-current decantation, having a nominal capacity of 200 tons, has been erected during the past few months and was put into operation during September of the present year. The ultimate capacity of the combined units of the present mill has not been determined, but it is expected to be much in excess of the rated capacity. The Ore The ore, as received at the mill, consists chiefly of quartz carrying free gold, with small amounts of pyrite, arsenopyrite, and pyrrhotite in evidence, though probably amounting to less than one per cent of the total. Some gold is very closely associated with the sulphides. The country rock is a basic igneous rock, probably an augite diorite. Near the vein it is highly altered to sericite, which slimes readily on grinding, and does not settle very well. The quartz is of two types, clear and ribbon. In the latter, the ribbons, which are not much thicker than paper, consist of shattered sulphides. In crushing this ribbon quartz, breakage is often along the streaks, exposing these shattered faces to advantage in subsequent treatment. While gold is the metal for which the ore is mined, some silver is also present and is paid for by the mint. It is, however, unimportant from a commercial viewpoint. From the standpoint of crushing and grinding, the ore might be termed 'medium 'hard'.

Jan 1, 1932

By Luino Jr. Dell'osso, Richard L. Every

The enormity of the methane-in-coal problem is discussed, with a brief summary of the state-of-the-art. Laboratory techniques and data on the desorption of methane from Pittsburgh seam coal are presented and discussed and include the effect of time, temperature and vacuum. Under laboratory conditions, it was possible to displace 90 per cent of the residual methane by flooding the coal samples with carbon dioxide. Carbon dioxide was found to be three times more effective than air and almost five times more effective than helium.

Jan 1, 1972

By S. Kaiman

This paper describes flotation test work conducted over the past several years at the Mines Branch, Ottawa, on the radioactive quartz-pebble conglomerate ores of the Elliot Lake area of Ontario. The purpose of this work has been to produce a uranium flotation concentrate for sub-sequent leaching operations. The results of earlier investigations are summarized and correlated with the results of mineralogical studies of the ores and flotation products. The results of recent pilot-plant investigations by flotation, as well as by gravity concentration followed by flotation of the gravity tailings, are given. The principal collector used for uranium flotation was a tall oil fatty acid, and the indicated total cost of all reagents ranged from 21 to 31 cents per ton of ore treated.

Jan 1, 1966

By P. E. Cavanagh

"The Davis tube test has been used for many years as a laboratory method for determining the magnetic iron re-coverable from a magnetite iron orebody. This paper de-scribes a method for determining the recoverable iron from ores of the Labrador Trough type, with the usua1 flow sheet utilizing spirals followed by magnetic separation.The mechanical structure of a metamorphosed iron ore, resulting from recrystallization over long periods of time, is the basis for the laboratory method developed. Similarities between the structures of such recrystallized ores and the structure of annealed and recrystallized steel are noted.A laboratory technique to determine the size of the different grains of gangue and iron ore minerals is de-scribed and the application of this information to arrive at recommended grinding techniques and flow sheets is demonstrated. The use of the method to determine recoverable iron in such ores is compared to actual iron recovery in the pilot-plant and commercial concentrations of the same ore.The use of a specified lower limit of recoverable iron as determined by this method, in order to design open-pit limits, achieves practical results when compared to designing a pit based on an arbitrary lower limit of total soluble iron. The Ungava Iron Ore deposits are used in giving an example of the resulting pit design changes."

Jan 1, 1968

By A. Consigny

New "clean technologies" to treat mining and metallurgical effluents containing dissolved metals have been successfully applied at mine sites in North America and Asia, treating water flows up to 24,000 m3/day. These clean technologies offer significant benefits compared to conventional alternatives and provide a sustainable solution that eliminates residual waste sludge, improves water conservation, generates revenues from wastewater, and delivers overall improvements to the environment. This paper will profile these technologies, and provide best practice case study examples of their application at mining operations, including data for water chemistry, flows, water quality, capital and operating costs, and life cycle costs of treatment.

Jan 1, 2011

By Boris Yacksic, R. W. Bruce

"The flotation of a cassiterite ore with oleic acid will recover primary or rougher concentrates assaying over 10 per cent Sn, with a recovery of 80 to 90 per cent. These rougher concentrates cannot be up-graded to a marketable grade by normal reflotation. Experiments were conducted on low-grade tin ores, and a process was developed for up-grading the rougher flotation concentrates by a reverse flotation technique. The process was tested on a number of samples of ore from the Catavi mine in Bolivia. The results of these tests showed that a concentrate assaying 40 to 60 per cent Sn could be readily produced, with a recovery of 60 to 75 per cent of the tin in the ore."

Jan 1, 1967

By E. J. Marcotte

"INCO LIMITED'S Shebandowan Mine and Mill is located in a scenic tourist and cottage area near the western tip of Lower Shebandowan Lake, approximately 90 Km west of Thunder Bay, Ontario. This nicely designed complex is a positive indication that mining operations can co-exist in harmony within the natural environment.The Shebandowan complex processed nickel-copper ore from 1973 to 1985, inclusive, after which operations were shut down.In late 1988, INCO LIMITED decided to place the Shebandowan complex back into operation, under contract, to mine and mill the remainder of the ore body, according to their specifications. MaclSAAC'S EXPLORATIONS was the successful bidder for the project. Following preliminary rehabilitation, operations were re-activated in late March, 1989. The ore mined to date is of a moderately lower nickel grade than the majority of previous years. However, a higher tonnage rate, combined with improved nickel recoveries, has contributed to a viable operation.A series of mill operating and equipment modifications has enabled MaclSAAC EXPLORATIONS to achieve the quality and grade of nickel-copper concentrates specified, and at the same time, expand mill tonnage throughput while attaining increased nickel recovenes."

Jan 1, 1992

By M. Bouchard et G. Martineau

In the Chibougamau area, a large portion of the glacially tranported boulders which were deposited at the surface were later partly remobilized by the waters of Glacial Lake Ojibway. In the dispersal studies of these boulders, it is sometimes difficult to discern the effect of this reworking process. In addition, depositional processes in the lake contributed material to the original block deposits through the formation of boulder lag by littoral wave action and through direct sedimentation in the form of deltaic deposits. In spite of these complicating factors, dispersal studies at carefully selected sites which were unaffected by the above processes make it possible to unravel the general patern of glacial dispersion. In this study, indicator lithologies of the Albanel and Chibougamau formations were used. They give a coherent image of dispersal throughout the area showing transport toward the southwest. Considering the particular geological context of the region, and in view of the extensive mineral exploration studies which are being carried out, the results of this study are encouraging for the tracing of source areas of glacially transported mineralized boulders.

Jan 1, 1984

"ALTHOUGH Canadian metallurgists have long been active in research, the scope of the work was somewhat limited until the be-ginning -of World War II. The rapid industrial development of Canada during the past ten years has been accompanied by .a similar upsurge in research. However, the wide geographical distribution of the research centres has made it difficult for the individual research workers to meet together and to exchange ideas or even to learn what projects .are being investigated or the nature and extent of the facilities available for work of this kind.The purpose of the present symposium is to assemble data relating to projects under investigation and the facilities employed at the various metallurgical research laboratories in Canada, thus providing some measure of correlation so that workers in different locations may learn what kind of work •is being .done at other points throughout the country.In reporting the symposium it has not been possible to reproduce the papers in full, but excerpts have been selected that give the essentia1 data."

Jan 1, 1952

By Janet E. Halliwell

In keeping with the traditions of the Science Council of Canada - an independent and forward looking agency that applies broad and multidisciplinary analyses to the various issues it examines the author indulges in a holistic approach to the integration of the environmental, scientific, economic, and cultural concerns. This paper will characterize the changing conditions which the mining industry is facing. It will then explore the changing expectations of society with respect to environmental sustainability and how those attitudes in turn, must influence the strategic directions and attitudes of the industry, and within that, the role of science and technology.

Jan 1, 1991

By P. R. A. Andrews, R. K. Collings

"There are more than 300 occurrences of fluorite in Canada. Deposits of economic significance, however, are confined to Newfoundland and Nova Scotia in eastern Canada, Ontario in central Canada, and British Columbia in western Canada. Fluorite has been mined and processed intermittently in Ontario and Newfoundland until November 1990, when Canada's only producer Minworth Ltd., a U.K. based company, with a mine and concentrator near St. Lawrence on the Burin Peninsula, Newfoundland, closed its operation.CANMET has processed ore samples from each of the major mineralized areas, and thirty-one studies were conducted between 1920and 1970. A summary of the important aspects of the various testwork studies is presented. The production of acid-grade fluorite was possible by flotation, and ceramic-grade, by flotation and gravity concentration methods. Gravity concentration methods included heavy media separation, jigging and tabling. Flotation was by direct and reverse techniques; associated minerals, quartz, calcite, barite, etc. were depressed by a variety of depressants. The function of the major depressants is discussed briefly. The various uses offluorite which include hydrofluoric acid, chlorofluorocarbons, aluminum production, petroleum alkylation, fluxing and ceramic applications etc. are discussed briefly."

Jan 1, 1993

By Leon C. Botham

?? Review of Requirements ?? Components of Modeling ?? Water Management ?? Tailings Management ?? Primarily a water management problem ?? Solids relatively easily contained ?? Process flows and runoff a continuous stream over life of mine ?? Need to allow this to safely happen over wide range of conditions

May 1, 2008

By R. H. McCorkell

Measurements of radon in air and aqueous solutions can be affected by leakage from vessels in which samples and standards are kept and by absorption and later release of radon by the materials of these vessels. The author had received various oral communications concerning the se processes : e.g ., that natural rubber and greases absorb large amounts of radon, whereas silicone rubber and grease do not; and that radon is readily lost from polyethylene bottles and that inverting glass bottles containing aqueous samples reduced radon loss from them . However, the results of actual tests and quantitative data showing these effects were not available. For this reason, it was necessary to make numerous measurements of the leakage and absorption of radon in the course of designing apparatus and methods for measuring radium and radon concentrations. It was thought that the data obtained might be of use to others, and consequently they are compiled in the present note .

Jan 1, 1980

By Jacques Ouellet

Outline What is Microwave energy Investigation of transparency of 40 minerals Melting of Andesite in a MW oven Numerical modeling /Computer Simulations o FEM analysis ?? Some laboratory experiments o Particle Modelling Mw Application to Rock Breakage o A MW Rock Drill Prototype Conclusions What is Microwave energy Microwave energy is an electromagnetic wave consisting two electronic & magnetic wave traveling perpendicular to each other and transporting energy with the speed of light.

May 1, 2008