Search Documents

By X. T. Feng, Y. H. Hatzor, Y. Tal, G. Yagoda-Biran

"When studying jointed rock mass deformation around underground openings it is of great importance to model correctly the excavation sequence during the numerical simulation. This is because for effective arching mechanism to develop in the roof minute block displacements must take place and some of the available discontinuities shear strength must be mobilized. If from the beginning of the simulation the underground opening already exists in the numerical model, block displacements into the excavation space will initiate and develop from time zero, before the initial stresses in the model have attained their actual initial level in the field. These initial block displacements are therefore artificial and exist only in the numerical model, not in the physical reality, and may lead to erroneous assessment of the stability of the designed structure, typically on the conservative side. We have introduced sequence excavation capabilities both in the numerical manifold (NMM) and the discontinuous deformation analysis (DDA) methods and show here the advantages of this modification using three different case studies, each illuminating a different aspect of this enhancement.We begin with the 25 meter deep 2000 year old underground Zedekiah limestone quarry below the old city of Jerusalem, Israel, which is still standing today unsupported with a free span of 40 m. We show that when the opening exists from the beginning of the numerical simulation the required friction angle for roof stability is 25 degrees, whereas when the opening is removed after all stresses and displacements in the model have been stabilized the required friction angle for stability is only 15 degrees.We then model the excavation sequence of a tunnel model representing a 2500 meter deep research tunnel in the Jinping hydroelectric project, China, in order to determine the in situ stress field at this depth by a grid search inversion of displacement data obtained using the sliding micrometer technology in the course of tunnel excavation. Thus we are able to constrain the in situ stress field at these depths where standard in situ stress measurement procedures are extremely difficult to execute properly.Finally, we use sequence excavation modeling capability to find the total height of the expected loosening zone around tunnels excavated through columnar jointed basalts which pose a great engineering challenge because of the characteristic dense network of slender prismatic blocks that transect the opening at a steep inclination. We use MPBX data obtained during excavation of a deep tunnel through such a rock mass to validate our numerical results and show that application of standard empirical guidelines for dimensioning rock bolt reinforcement in such rock masses may in fact result in very un-conservative design because existing empirical approaches typically ignore the anisotropic nature of the structure of such rock masses which, as we show, plays a very significant role in determination of the extent, shape, and geometry of the loosening zone around the opening."

Jan 1, 2015

By M. Li, T. H. Dubaniewicz, H. N. Dougherty

"INTRODUCTION Underground mines have the risk of accumulation of gases if not ventilated properly or during and after emergency situations when ventilation controls become damaged or stop working. Common gases that are monitored in underground coal are carbon monoxide (CO), oxygen (O2), and methane (CH4). Methane is a gas found in coal and released through mining; its explosive range is between 5% and 15%. Methane is commonly monitored on all mining equipment and with handheld gas sensors carried by most underground coal miners. Fiber optics (FO) is a popular technology applied in underground mining, particularly for its electric isolation. Many miners are familiar with FO cables hung throughout the mine, which are primarily used in the communication of voice and data (Taylor et al. 2010). Advancements in laser and fiber optics have made this technology well suited for gas sensing the harsh environment of mining applications. The work of the U.S. Bureau of Mines on the use of fiber optic monitoring of gases in mines started in 1992. Dubaniewicz et al. (1992, 1993, 1995, 1999, 2003) developed prototype gas sensors, including methane gas sensors, for research purposes. Previous research (Dubaniewicz & Chilton 1992) identified potential fiber optic gas detection cross-sensitivities associated with the index of refraction of various gases. Index of refraction effects was noted for carbon dioxide (CO2), which is produced in significant quantities by mine fires or explosions. NIOSH released a broad agency announcement (BAA) for the development and demonstration of mine safety and health technology (CDC NIOSH 2017). The objective of this announcement was to validate a sensor, specifically fiber optic, for the mine environment and test it in an actual working mine. The RSL FO sensor “OptoSniff” provided from this work is capable of hundreds of sensing points over distances of up to 20 km, has a measurement range of 0.05% to 100%, senses in an oxygen- deficient environment, and has no gas cross-sensitivity (RSL, 2014). The RSL system is totally electrically passive outside the central control unit (CCU), which can be housed in an MSHA-approved explosion-proof (XP) enclosure or in a control room outside of the permissive area. The sensor was tested in dusty and signal loss situations, showing it is tolerant of dust, has functioned at signal losses up to 90%, and was successfully tested in a mine environment for a five-month period (Walsh et al. 2014). This paper describes how the RSL FO sensor is used for testing using smoke and its contaminants for applicability in emergency situations. The testing investigates individual contaminants such as CO2, temperature, and smoke. Each test was performed separately and methane concentration, laser power, and response time data were collected."

Jan 1, 2019

By Wataru Inagaki, Kozo Kawano, Tetsuya Ando

Cu–Ni–P alloys are the typical precipitation-hardening material. Thus, Cu–Ni–P alloys is expected to apply alternative materials for heat-exchanger tubes. Therefore, it was investigated that the effect of the heat-treatment simulated brazing on mechanical properties of Cu–Ni–P alloy in this study. The hardness of specimen as heat-treatment simulated brazing after solution heat treated (sht) was shown approximately 105 HV. The peak hardness and tensile strength of the specimen as performed aged at 498 K for 43.2 ks following the heat-treatment simulated brazing achieved at approximately 140 HV and 260 MPa, respectively. From these results, it is expected the application to higher-strength tube for heat-exchanger after brazing in a furnace. INTRODUCTION Copper prices have increased dramatically with high in recent years. At the same time, manufacturing industries are required to reduce the environment load by reducing the wall thickness of the copper tubes used in heat exchangers. High-strength copper alloys are developed for reducing the wall thickness, while achieving high strength, of the copper tubes. Moreover, excellent workability and corrosive durability are also required by these copper tubes. Furthermore, the brazing, which are carried out at about 1050 K during the assembly process of heat exchangers, leads to grain growth and re-solving of additive elements. Nomura et al. achieved a tensile strength and Vickers hardness of approximately 260 MPa and 110 HV, respectively, after aging at 723 K for approximately 36 ks. Tamagawa et al. studied that the strength of Cu–Ni–P alloy rapidly increased at about 125 HV during the cooling process after the heat brazing due to the Ni2P precipitates sized 5–10 nm. Furthermore, Inagaki et al. achieved a Vickers hardness of approximately 130 HV by aging at 498 K for 10.8 ks. In the present study, we focused on the lowest aging temperature of 498 K in the previous study, and investigating the effect of heat-treatment simulated brazing on the mechanical properties of the Cu–0.93 mass%Ni–0.24 mass%P alloy.

Jan 1, 2019

By Mark Kennedy, Allan MacRae, Cameron Hams

New technology projects, particularly those involving first-of-a-kind metallurgical facilities, have a poor track record of achieving their overall financial targets, as they incorporate technological risks in addition to normal project risks. Traditional project management tools focus on risk from concept development through implementation, but typically fail to address the additional risks associated with a new technology project including slow start-up, slow ramp-up, and failure to achieve design performance (quality or throughput). These additional risks affect future cash flows produced by the project and hence its value, typically measured as net present value (NPV) or internal rate of return (IRR). Common accounting practice is to reduce the present value of future cash flows by applying a chosen discount rate, often reflecting the corporation's cost of capital. This discount rate does not contain an allowance for technological risk, which is often underestimated or misunderstood by both the financial and engineering project managers. This paper will focus on the topic of project risk and new technology, and how these play a role in the probability of achieving the predicted future cash flows. By properly addressing technological risk in the form of risk-weighted returns, marginal projects can be prevented from proceeding, while sound projects can be given the additional time and resources required to achieve the optimal level of front-end-loading (the level which returns the maximum risk-weighted net present value). A simple set of mathematical tools should enable engineers and financial professionals to establish a common level of understanding, thereby leading to a more accurate assessment whether a new technology project is ready to pass through its next level of approvals.

Jan 1, 2011

By Martin Lebeuf

The phenomena occurring in the cathode and at the cathode surface of aluminum electrolysis cells are very important in regards to cathode voltage drop and cathode wear. In the current study, laboratory-scale aluminum electrolysis cell cathodes were analyzed by X-ray microtomography. This technique allows an excellent visualization of the distribution of different substances, if their respective X-ray attenuation coefficients are different enough. In the current case, the important difference in the mean atomic number between cryolitic bath and graphitic carbon results in good contrasts. The volumetric bath penetration profile, porosity and impurities distribution in the cathode were thus obtained. Furthermore, metallic impurities and bath heterogeneities were observed at the cathode surface. Observations were also made with Scanning Electron Microscopy - Energy Dispersive Spectroscopy (SEM-EDS).

Jan 1, 2011

By Kirsten Corin, Margreth Tadie, Cyril O’Connor, Jenny Wiese, Wonder Chimonyo

"Relating flotation performance to the electrochemical characteristics of a pulp remains a complex issue both in fundamental research and in practice. For example, in the case of thiol collectors different Eh values can result in the formation of the dimer or the metal thiolate which may or may not enhance the hydrophobicity of the mineral. Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, are usually manipulated to achieve an optimum flotation response by the control of pH and dissolved oxygen levels in the system. It is also possible to vary the potential by the addition of modifiers such as sodium hydrosulphide (NaHS), sodium hypochlorite (NaClO) or hydrogen peroxide (H2O2). The objective of the present study was to investigate the effect of the addition of the oxidising agents, NaClO and H2O2, on valuable mineral recoveries and grades in the flotation of sulphides from a PGM bearing Merensky ore. Batch flotation tests were conducted at pH 9.2, the natural pH of the system, in the absence and presence of a xanthate collector and Eh modifiers, viz. NaClO or H2O2. Most importantly in this way it was possible to vary Eh at constant pH and DO levels. The results indicate that in the absence or presence of xanthate the addition of H2O2 reduced both the recovery and grade of copper and nickel. In the absence of xanthate, the addition of NaClO improved the recovery of copper slightly and both the recovery and grade of nickel significantly, but in the presence of xanthate NaClO addition resulted in unchanged copper recovery and grade, but those of nickel were reduced. Based on anecdotal evidence that the addition of trace amounts of a potential modifier could improve flotation performance further tests were conducted the results of which suggest improved flotation performance.INTRODUCTIONIn the Merensky Reef, platinum group minerals (PGM) are commonly associated with base metal sulphides (BMS) and this has an effect on the way in which these minerals can be concentrated by flotation (Vermaak, Venter & Pistorius, 2004; Wiese, Harris & Bradshaw, 2005; Schouwstra, Kinloch & Lee., 2000). A major problem stemming from this association has been reported to be the loss of valuable minerals (PGM) associated with the loss of BMS (Wiese et al., 2005) during flotation. Shackleton (2007) suggested that PGMs behave in a similar manner to sulphides during flotation. Therefore, in order to recover the PGM, base metals are targeted. There is thus a need to investigate ways to improve the flotation performance of the sulphide minerals. The electrochemistry of the flotation of sulphide minerals has been studied for over half a century and there is consensus that sulphide minerals float only under a suitable redox environment (Heyes & Trahar 1979). This implies that reducing and oxidizing conditions during flotation of ores such as Merensky can be manipulated/varied to achieve an optimum flotation response.During flotation, sulphide minerals interact with thiol collectors in an electrochemical reaction to form hydrophobic species at the mineral surface (Finkelstein & Goold 1972; Rand & Woods 1984). The sulphide minerals are semiconductors and their interaction with collectors involves transfer of electrons. As such, a potential difference results which is responsible for driving electrons between reacting species (Fuerstenau, Jameson & Yoon, 2007). The magnitude of the potential difference affects the relative energies of charge carriers (electrons) at the mineral/solution interface hence controlling the direction and rate of charge transfer or rate of reaction (Bard & Faulkner, 2001). In a mixed mineral system the mineral/solution interface potentials account for the mixed potential which is critical to the process of flotation (Chander, 2003; Woods, 2003)."

Jan 1, 2016

By Andrew Barnes

The adsorption capacity of peat collected from a proposed mine development in northern Sweden has been determined using laboratory column experiments in which peat was irrigated with a simulated (acidic) waste rock dump leachate. The simulated leachate was made using a hydrogen peroxide leach of composite waste rock from the proposed mine development. The waste rock samples were composited in proportion to their predicted extractable tonnage for the mine development in order to generate a more representative leachate solution for the waste rock facility. As expected the test revealed that the peat material shows a very high affinity for attenuation with greater than 70% of Co, 90% of Ni and 95% of Cu removed from influent solutions through the majority of the tests demonstrating the potential benefits in mine water treatment. In contrast, it was found that Fe is initially released from the peat at concentrations up to 100 mg/L and can mean potential problems for the water released depending on the receiving environment. The exact mechanisms for Fe release is uncertain, though it is suspected that ion exchange / competitive desorption is responsible. Inspection of the laboratory results and drainage data from the natural peat wetland receiving drainage during overburden prestriping and mine development at the mine site are comparable, confirm the validity of the experiments, and further emphasize the potential for future use of pre-stripped peat material in managing water quality.

Aug 1, 2013

Waste rock extracted from a mine is typically stored nearby on the surface. Such waste rock piles must be designed to ensure their geotechnical and geochemical stability during the mine operation and after closure. The optimal construction of a pile requires detailed planning. Deposition should involve benches of limited height to control the global slope angle, based on the long term factor of safety. It can also be advantageous to compact the top of each bench and to give the surface an outward inclination to control water flow by limiting infiltration and favoring lateral diversion. When part of the waste rock contains reactive minerals, it is also deemed necessary to use selective placement with the non-reactive portion to prevent direct exposure to natural conditions. The construction must be well documented, and include data from the monitoring program. These and related aspects are presented and discussed in the paper.

Aug 1, 2013

By O. G. Olvera, D. G. Dixon, E. Asselin, L. S. Quiroz

Dissolution rates of chalcopyrite (CuFeS2) were calculated using electrochemical impedance spectroscopy (EIS). The calculated dissolution rate decreased by a factor of 3.2 after the electrode was passivated. The results presented in this work indicate that the reduction of Fe3+ was the rate-controlling step for fresh CuFeS2 electrodes while the transport of cations within the passive film limited the dissolution rate for the passivated electrode. The transfer of cations at the electrode/electrolyte and passive film/electrolyte interfaces did not affect the dissolution rates of the fresh and passivated CuFeS2 electrodes, respectively. The catalytic effect of pyrite (FeS2) on the dissolution of CuFeS2 continued after the passivating treatment. The contact of fresh and passivated CuFeS2 electrodes with different FeS2 particles resulted in increased dissolution rates, due to an increase in the reduction rate of Fe3+.

Jan 1, 2014

"Acid resistant brick lined autoclaves and related vessels are utilized in pressure oxidation for the recovery of gold, copper, and other metals. The combination of the corrosion resistant membrane, acid resistant brick, mortar and steel shell is a composite system that requires a sophisticated stress analysis. In order to obtain meaningful results both the model and physical properties of the materials must be carefully selected. Evaluation of the calculated results requires an understanding of both the failure mechanisms of ceramics and experience with the performance of existing lining systems.INTRODUCTIONAcid brick lining systems are used in pressure oxidation autoclaves and related vessels to provide thermal and mechanical protection for corrosion resistant membranes that are applied directly to the interior of the vessel shell. The acid brick and mortar must be resistant to the process conditions and must provide a mechanically reliable structure.The construction of lined vessels incorporates a wide range of materials that can include the carbon steel vessel, austenitic weld overlay, lead lining, organic membrane, ceramic brick, mortars and other alloy components. The physical properties of the materials can vary by orders of magnitude and when combined in the construction of the lined vessel create a complex composite structure. The materials may be bonded together or act independently of each other. Stresses are induced into the lined vessel include pressure, thermal expansion, chemical expansion and mechanical loads.The complexity of these systems makes it is very difficult to account for all of the variables in the structural analysis of lined vessels. Historically calculations were simplified and designers primarily relied on experience with previous applications.The greatly improved tools for Finite Element Analysis (FEA) available today allow for detailed calculation of the stresses imposed on the vessel shell and lining. Koning & Lauzon (2004) presented a paper on design fundamentals including a discussion on the application of FEA methods at Pressure Hydrometallurgy 2004 in Banff. When a designer carefully constructs a model and selects the correct materials properties for the calculations, meaningful and useful results can be achieved."

Jan 1, 2012

By Donald F. MacDonald

METAL PRICES RISE WITHIN the past nine months, the mining industry of the world has been revivified by a spectacular price advance for the metals. ln fact, practically all geological raw materials have been marked up during this period. Reviving industry started the price rise, but the armaments race among the nations has intensified it. These factors, coupled with our decided building shortage, which must be made up, will probably maintain metal prices at decidedly favourable levels over the next two or three years, or longer. OUR MINERAL CIVILIZATION It is interesting to recall that in the past hundred years, while the white population of the world increased some three ta three and a half fold, the consumption of minerals increased seventy-five fold. In other words, ours is a mineral civilization. If we disregard short slumps, which we will occasionally experience, it seems certain that the bread upward trend in mineral consumption will be maintained for many decades into the future. Nations without reasonably abundant and diverse mineral deposits will eventually become nations without much power. Canada is blessed with a splendid store of minerals. Its mineral industry is now facing an exceptionally rosy future. What of the mineral industry of Nova Scotia? GEOLOGICAL RESEARCH ALLOWED TO LAG RN NOVA SCONA Many years ago, when geological science was in? its infancy, much geological study was carried on in Nova Scotia. In 1827, Francis Alger began work on the iron ores in the Bay of Fundy region. In 1886, E. R. Faribault began his series of remarkable papers on Nova Scotia geology. Between these dates, many others published papers on the geology of the Province. The most outstanding of this early group of geologists was Sir William Dawson, whose published works on Nova Scotian geology extended over the period from 1845 to 1891.

Jan 1, 1937

By L. Jiang

This report investigated the dynamic recrystallization (DRX) phenomenon in magnesium alloy AZ31 billets to understand the deformation mechanisms and microstructure evolution during extrusion and other metal forming processes, Compression tests of coarse-grained as-cast magnesium alloy billets containing lamellar Mg17Al12 eutectic phase and (Al, Mn) particles suggest that temperatures higher than 300°C, strains greater than 0,25 and strain rates above 0,l/s lead to the formation of fine DRX grains in the deformed samples. Microstructural observations also indicate particle-stimulated DRX nucleation (PSN) during hot deformation of the AZ31 alloy, facilitated by the presence of Mg17Al12 and (Al, Mn) particles, While the Mg17Al12 is dissolved into the matrix at about 350°C, (Al, Mn) particles may remain effective for PSN at temperatures up to at least 400°C, This study suggests that alloy design with a proper distribution of second-phase particles can provide the desired microstructure for improved properties and formability in wrought magnesium alloys.

Jan 1, 2004

By K. Bowes, M. D. Maley, R. J. Ring

The Honeymoon Uranium Project is an acid In-Situ Recovery (ISR) mine in South Australia. It was previously operated for approximately 18 months before being placed on care and maintenance in 2014, it was then acquired by Boss Resources in 2015. Boss has been performing a number of studies to plan for reopening of the mine, including a successful field leach trial (FLT) in 2017. The current configuration for uranium precipitation at Honeymoon is a batch process. Whilst this achieves effective uranium recovery, the precipitates produced are often very fine, with poor settling and solid/liquid separation characteristics. Continuous precipitation, involving recycling of solids, has reportedly been successfully utilised in other operations to increase the particle size and density of the product, leading to solids that can be more readily dewatered, dried and drummed, with less fines and dust generation. However, no operational data are available from such operations.

Jan 1, 2020

By Marcel Vallee, D. C. Gagnon, C. CARBONNEAU, P. ST-JULIEN

The Magdalen Islands archipelago, a cluster of fifteen islands, is located near the centre of the Gulf of St. Lawrence on the thickest portion of the Carboniferous Fundy Basin of the Maritime Pro vinces. The bedrock of the Magdalen Platform includes a thick succession of evaporites of Visean Age, occurring as a series of thickenings, ridges, domes and diapirs reaching a probable vertical thickness of close to 6000 m. The emplacement of 1hese salt structures by flowage has much dislurbed 1he SlrOligraphic sequence of the rocks of the Windsor Group, particularly 1he Havre-aux-Maisons Formation. Subsequent tectonic movemenl has broken the overlying Cap-auxMeules Forma1ion info an assemblage of panels and blocks now slightly tilted. Following detailed gravimetric surveys and more than 30,000 m of diamond drilling, SOQUEM has discovered, at various dep1hs, seven salt domes on four of 1he main islands of the archipelago. These evaporite bodies generally are localized near the cemre of complex anticlinal struclUres where diapiric movements and faulting have disturbed the original stratigraphic succession. At Rocher du Dauphin near Grosse 1/e, in 1he northern part of the archipelago, Seleine a SOQUEM subsidiary is developing a mining complex with an annual capaci1y of 1,250,000 1onnes of deicing salt for 1he Canadian and Eas1ern United Swtes marke1s. The stan of operations is scheduled for April 1982.

Jan 1, 1984

By JOHN H. HUDSON

Ceramic clays of the Prairie Provinces range in age from Lower Cretaceous to Pleistocene and Recent. Two significant ceramic clay horizons are the Paleocene Willo wbunch Member of the Ravenscrag Formation in Southern Saskatchewan and the Upper Cretaceous Whitemud Formation, which is found in Saskatchewan and Alberta. The Willowbunch Member is worked at one locale in Saskatchewan; the Whitemud Formation is worked at several locales in Saskatchewan and Alberta. Bentonite operations are found at Morden in Manitoba, Rosalind and Onoway in Alberta, and Wilcox in Saskatchewan.

Jan 1, 1984

By Dart Wantland

"AbstractThe scope of geophysics in civil engineering and the nature of exploration geophysics are briefly discussed. Engineering problems amenable to geophysical attack are illustrated by specific examples. The various methods available, accuracy of results, and costs are treated. The possibilities of new uses of geophysical techniques are pointed out.IntroductionTHE SCOPE of geophysics in engineering is different than in oil or mining exploration. In civil engineering, geophysics solves specific problems; as for example, what is the depth to bed-rock along the axis of a proposed dam? The area to be surveyed is of limited extent, and the subsurface information .sought is relatively near the surface. The engineering geophysicist is not called upon to investigate geological basins or extensive mineralized areas or to probe for data to thousands of feet in depth. The geophysical tools employed in the three fields are, however, quite similar; the differences are mainly in the objectives.The Natural Geophysical ExplorationThe terms geophysics and geophysical exploration have been used heretofore and will .be employed in what follows. The question is, therefore, What is geophysical exploration?Geophysical exploration is a line of field work where measurements are made at the ground surface with special instruments to get geological subsurface information. Briefly stated, geophysics is a form of exploration that supplements geological work. It is a blend of physics and geology since physical measurements are made •at the surface of the ground that can be interpreted in terms of subsurface conditions."

Jan 1, 1953

By Desmond Y. M. Lee

This paper presents a procedure to prepare input for the computerized pit design system at Iron Ore Company of Canada. The procedure is simple and requires very little training. Also, it is general enough to accept both bench (horizontal cross section) maps and section (vertical cross section) maps. The output of this procedure is data which represent blocks of ore and waste with dollar values based on mineral content. The ultimate pit design is presented in printer-generated graphs, with numbers indicating the depths of pit bottom walls. Roads are added manually by the engineer with the aid of other computer programs. Section maps and bench maps are also printed as part of the output of the ultimate pit design.

Jan 1, 1978

By A F. Kravic

Carbonyl nickel powders of irregular particle shape and low a11parent density are used extensively in the production of porous nickel electrodes for nickel-cadmium storage batteries and hydrogen-oxygen fuel cells employing alkaline electrolytes. Such porous nickel matrices are at-tractive for these intended applications as they are relatively inexpensive, are corrosion resistant, have good electrical conductivity, can be welded to form electrical contacts, have a long life (as demonstrated in alkaline storage batteries), and are rugged and vibration and shock resistant. This paper describes a feasibility study concerning the production of porous multi-layer nickel electrodes by the pressing and sintering of stacked layers of green-powder rolled nickel sheet. Background H AUSNER (1) conveniently listed nine different powder compaction processes used for forming metal powders into useful shapes. These are shown in Table I. There are additional powder metallurgy processes; however, most of these are combinations of two or more processes listed in the Table. A study of the literature revealed that every powder compacting process, with the exception of isostatic pressing and explosive forming, has been evaluated or is being used for the manufacture of porous metal electrodes.

Jan 1, 1965

By T. R. Eger

Miners can be exposed to whole-body vibration (WBV), when sitting or standing to operate mobile equipment. In order to prevent vibration-induced injury it is important to understand how miners can be exposed to vibration, the health risks associated with vibration exposure, methods to evaluate vibration exposure, and strategies to reduce vibration exposure. WBV exposure typically occurs when operating mobile equipment, such as a load-haul-dump vehicle, haulage truck, or dozer. The probability of health effects such as low back pain, neck pain, headaches, and gastrointestinal track problems occurring from daily vibration exposure can be determined based on criterion values published in ISO 2631-1 and EU Directive 2002/44/EC. A special case of WBV termed foot-transmitted vibration (FTV) occurs when a miner is exposed to vibration that travels through the feet. FTV typically occurs when standing on vibrating surfaces associated with the operation of locomotives, jumbo drills, bolters, or raise platforms; however, there is no set standard to evaluate health effects associated with FTV. Recent medical evidence confirms workers exposed to FTV can develop cold induced blanching of the toes, in addition to numbness and tingling in the feet and toes. In order to reduce the risk of adverse health effects from exposure to vibration, the hierarchy of controls (elimination; substitution; engineering; administration; and personal protective equipment) should be followed. Best practices should be used to minimize vibration exposure through equipment purchases (i.e. vehicles with lower vibration emissions and seats that attenuate vibration), reduced driving speeds, and improved road maintenance for example. The elimination of other risk factors, which increase injury risk when combined with WBV exposure, such as awkward working postures, should also be eliminated. Very little is known about FTV exposure therefore further research is required in order to develop exposure standards and identify prevention strategies.

Aug 1, 2013

By Hani S. Mitri

Overhand cut-and-fill mining of narrow vein orebodies inevitably leads to the creation of horizontal pillars. As the thickness of the overlying crown pillar diminishes, stresses build up in the pillar. More often than not, this situation causes an increased level of seismicity and possible pillar burst. One well-known strategy to reduce the hazard of crown and sill pillar burst in cut-and-fill vein mining is that of destress blasting. The paper first reviews the methods used for the monitoring and assessment of potential pillar burst in narrow vein cut-and-fill mining. The influence of horizontal stress, mine depth and pillar thickness on stress build-up in the crown pillar is examined through a characteristic narrow vein numerical model. The paper then presents, with reference to three mine case studies, the benefits of destress blasting and the factors affecting its success as a ground control technique.

Oct 1, 2001