Search Documents

By Larry A. Haas

The U.S. Bureau of Mines is investigating ways of enhancing the high-temperature softening-melting (HTSM) properties of domestic taconite pellets. These properties, which are important for determining the performance of pellets in blast furnaces, include pellet bed contraction, pressure drop, S-value (area under the pressure-temperature curve), and softening and metal-slag drainout temperatures. Experiments showed that HTSM properties were related to the physiochemical properties (fired strengths and reducibilities) of pellets containing different levels of limestone and dolomite flux. Flux additions resulted in slightly lower green and fired pellet strengths, but improved metallurgical properties, such as reducibility. The influence of reduction conditions on HTSM properties was evaluated by varying the pellet metallization starting temperature and the carbon monoxide content of the CO-N2 gas mixture. HTSM property change was more sensitive to flux addition levels when metallization was initiated at 1,100° C with 20 pct CO in the gas stream. The S-value and the metal-slag drainout temperature were found to be the best criteria for characterizing HTSM properties. The optimum flux addition level was about 8 pct (4 pct dolomite, 4 pct limestone) or a basicity of about 1. At higher flux levels, a higher metal-slag drainout temperature was obtained.

Jan 1, 2010

By Bruce I. Thomas

Reconnaissance studies of beach sands along the eastern part of the Gulf of Alaska were conducted by the Bureau of Mines to determine if any of these coastal areas warranted investigations as possible sources of valuable minerals. Because of difficult access and limited transportation facilities only a minimum of sampling, surveying, and camping equipment is utilized to obtain spot samples from key areas as well as information indicating the location, size, and character of the deposits. Such data were obtained from beaches located along approximately 247 miles of the Gulf of Alaska coastline during parts of the 1957 and 1958 field seasons. A total of 201 3-inch-diameter auger holes, spaced roughly at 1 mile intervals, were bored by hand methods to depths ranging from 3 feet to 27 feet; also 33 shovel samples were collected from selected localities. Samples were reduced to a rough concentrate in the field by panning; the rough concentrates were shipped to the Bureau of Mines laboratory at Juneau for further concentration and for petrographic and chemical analyses. Particular attention was given to the heavy-mineral content of the concentrates, although the types and relative amounts of rock-forming minerals were also determined. The reconnaissance indicated that, generally, the valuable mineral content of the beach deposits was too low to be of further interest except in the vicinity of Yakutat and Lituya Bays where erratic but possibly significant concentrations of magnetite and/or ilmenite were found. At Yakutat, about 20 miles of beachline extending southeasterly from Ocean Cape, yielded samplas containing from 1 pound to over 300 pounds of iron and from a trace to over 100 pounds of titanium dioxide (TiO2) per cubic yard of beach material. However, the higher grade samples represented local concentrations of minor importance. The general tenor of the Yakutat beach, as indicated by the airthmetical average of 27 auger-hole samples, is about 35 pounds of iron and 20.5 pounds of titanium dioxide per cubic yard of beach material. Ilmenite is the predominant heavy mineral of the beach deposits in the vicinity of Lituya Bay, but it was found in concentrations only in limited areas near the

Jan 1, 1962

By Lulie H. Crump

U.S. supply and demand data for petroleum and natural gas liquids, by States and regions, were tabulated for the years 1960 and 1965. Estimates arcs provided of State-by-State quantitative data for the petroleum and natural gas liquids industry that can be integrated into State, regional, and national energy balances by source, form, and consumer sectors, and used for determination of interstate and interregional energy flows. Tables 1-4 show the estimated total supply of petroleum available for consumption and the supply's distribution among the major consumer demand sectors (household and commercial, industrial, transportation, and electricity generation). To obtain summary figures for the major proportion of refined products by States, individual tables were compiled for the six major products (tables 5-16). To enable comparison of petroleum data with those for other energy forms, conventional volumetric data in barrels were converted to their British thermal unit (Btu) equivalents. Interregional shipments of crude petroleum and theoretical flow patterns for petroleum products are shown in figures 1-4.

Jan 1, 1969

The objective of this research was to evaluate the technical and economic constraints on the extraction and utilization of anthracite coal and to determine the research and development needed in order to make anthracite coal more fully utilized as a premium energy resource. In the report the contractor examines in detail the anthracite industry both past and present and evaluates market possibilities. Anthracite reserves and resources are analyzed and tabulated, and the problem of pumping and drainage from the flooded anthracite fields is covered. Current technology is considered in detail with a discussion of production techniques with potential for improvement. The contractor concludes the report with a summary of constraints on the anthracite industry and the contractor's recommendations for effecting a revitalization of that industry. An estimated production of 17 million tons annually by 1990 can be anticipated if adequate planning, research, and development to overcome present constraints are initiated in the near future.

Jan 1, 1975

By Ferron A. Olson

Natural bornite (Cu5FeS4) leached in ferric chloride or in sulfuric or hydrochloric acid solutions with oxygen showed several differences. In ferric chloride 80 of the copper was leached in two stages. The first (30 copper removal) requiring one minute was controlled by mixed kinetics (liquid ferric ion diffusion and chemical surface reaction). The second was controlled by formation of a surface sulfur layer and then diffusion through the sulfur. With oxygen in sulfuric acid reaction was slow and only the first stage was studied. Copper removal had an induction period. The bornite structure disappeared at 12% copper removal (also found with ferric chloride) and covellite formed on the surface with a species inside the particles having an x-ray structure similar to CuFeS2 but with composition Cu3FeS4 (also with ferric chloride). Copper removal was controlled by iron dissolution. Surface iron vacancies filled with Cu+ to give CuS while interior copper dissolution produced Cu3FeS4. Preliminary results with oxygen and hydrochloric acid showed 80% copper removal and sulfur as end products (similar to ferric chloride).

Jan 1, 1982

By T. C. Woo

This report describes the program that studied the theoretical and practical aspects of the belt cleaning systems, investigated-the possibilities of a self-replacing and/or sell-adjusting belt cleaning device, and designed a horizonal pentagonal turret setup for the underground mine belt conveyors. This design resulted from comprehensive literature survey (both academic and commercial), actual mine visits, study of the mechanics of belt cleaning and bench-type experiments. It has complete working drawings and rough cost estimates.

Jan 1, 1977

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and operating costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per cfm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured under-ground. This volume constitutes Volume II of the report and contains the outputs of the computer simulation runs.

Jan 1, 1983

By James Gibbs

In order to provide an initial approach to the deposits of oil shale, nahcolite, and dawsonite in the central area of the Piceance Creek Basin in northwestern Colorado, the U.S.B.M. and associated contractor personnel drilled and cased a 96-inch ID shaft to a depth of 2,371 feet. The shaft was constructed using "big hole" drilling techniques and succeeded in giving access to previously inaccessible deposits of the above minerals. This report documents the construction from its beginning in January 1977 to its completion in January 1978. Procedures used and problems encountered are discussed in derail.

Jan 1, 1978

By Robert J. Dompe

The objective of this program was to develop a cost effective microprocessor-based electronic image sensor system for monitoring pit slope displacement to detect and/ or predict impending slope failure in surface mines. A background study and data analysis yielded a performance specification for candidate Video Slope Monitoring Systems. A design concept was developed based on using a pair of solid state video cameras located on precision pointing assemblies. The digital images from the cameras are compared and, using electronic triangulation, slope topology is calculated. The current and past locations of operator selected features are compared to determine pit slope displacement. A proof-of-concept test was performed using a laboratory model of a pit slope. Based on the successful results of that testing it is recommended that an in-mine evaluation be performed using a full-scale prototype Video Slope Monitoring System.

Jan 1, 1982

By Karl C. Dean

All components of 15 automobiles manufactured between 1954 and 1965 were analyzed, and it was determined that a representative junk automobile would have the following composition (all figures in pounds): steel, 2,532; cast iron, 511; copper, 32; zinc, 54; aluminum, 51; lead, 20; rubber, 145; glass, 87; miscellaneous, 142. Time and motion studies and a cost evaluation were made to determine if such a typical vehicle could be economically burned in a smokeless incinerator and hand-dismantled, and if the resultant steel could be baled into a high-quality No. 2 bundle containing less than 0.10 percent copper. The cost evaluation showed that processing the composite car would cost about $51 to produce about $56 worth of marketable ferrous and nonferrous metal products and provide an annual rate of return on investment of 19 percent.

Jan 1, 1969

By Eldon Keith Stanek

This annual report deals with four distinct tasks related to research on the safety and reliability of mine electrical power systems. Task one is to develop tests and the associated instrumentation to detect incipient faults on a mine or any low-voltage power system. Task two is a dual effort related to the digital prediction of electrical transients on mine power systems and laboratory testing of transient suppression devices. Task three is also a dual effort. This task consists of both theoretical and laboratory work to assess both the reliability and the fail-safe characteristics of several items of protective equipment used in mine power systems. Task four consists of an effort to use programmable calculators and/or computer terminals to check overcurrent protective device coordination.

Jan 1, 1976

By Jack Kadlecik

This final technical report describes the concept feasibility study, testing, design and development effort which went into. The quick opening enclosure access cover and flame path tolerance checking system. A detailed definition of the explosion-proof multiple start threads is shown for two (2) sized electrical enclosures.

Jan 1, 1972

By Robert Louis Adams

A general discussion of the structure of the junk automobile recycling system shows that the generation of stripped automobile hulks and scrapped automobiles is price inelastic. As a result, it is extremely difficult for the price mechanism to automatically achieve an equilibrium that will prevent the accumulation of excessive automobile wrecker inventories and vehicle abandonment by the last owners of scrapped cars. The new shredder processing technology and the new portable flattener technology have altered the structure of the junk automobile recycling system. The shredder technology has increased the demand for processed automobile scrap. This increased demand is reflected in higher prices paid for hulks by scrap processors. The portable flattener has reduced the transportation cost of shipping hulks to processors. The two new technologies have eliminated, at least potentially, the net cost of shipping stripped hulks so frequently incurred by wreckers in the past. The elimination of this cost eliminates the economic incentive for excessive wrecker inventories. Unfortunately, the incentive for last owners to abandon their cars does not appear to have been eliminated by the new technologies. The last owner of an automobile with no spare parts value is still likely to incur a cost by delivering his automobile to the recycling system. Although a subsidy payment is probably unnecessary to reduce excessive wrecker inventories, such a payment might be one solution to the problem of automobile abandonment. However, there are a wide variety of subsidy programs that could be introduced. Before any Federal subsidy program is introduced to reduce automobile abandonment, it is recommended that the program be tested on a limited basis in many different parts of the country.

Jan 1, 1973

By Roger E. Burleigh

In June, 1989, the U.S. Bureau of Mines, undertook a 9-day evaluation of the tin resource potential of the Sleitat Mountain tin deposit. Significant tin-tungsten mineralization is associated with quartz-topaz-white mica-tourmaline greisen alteration of a multi-unit, 57 Ma, peraluminous, granite stock which intrudes Cretaceous Kuskokwim Group flysch deposits. The granite comprises marginal biotite-, intermediate biotite-muscovite-, and central zinnwaldite-granite units, interpreted as a zoned alteration system. Major vein mineralization is confined to two east-west-trending zones of steeply oriented tabular lenses of greisen interleaved with mildly altered granite. Cassiterite is the dominant ore mineral while arsenopyrite, loellingite, wolframite, pyrite, sphalerite, chalcopyrite, and bismuth-oxides are present in minor to trace amounts. The north and south greisen zones are estimated to contain an inferred resource of 128 to 212 million lbs Sn in 28.6 million st of mineralized rock. An 1,800-lb representative bulk sample contained 0.37% Sn, 0.04% W and 17 ppm Ag and is considered an average grade estimate for the deposit. Drill testing by Cominco Alaska Exploration indicates that substantial widths of high-grade tin mineralization are included within the lower grade disseminated mineralization. Depth of deposit erosion is substantial and there exists a high probability for placer tin deposits.

Jan 1, 1991

By Richard L. Fowler

[Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting, obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the bear overage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve completely self-contained shuttle car system which responds to the mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to valuate various guidance techniques during the feasibility study. Subsequent simulation rues were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing wan performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated Chi predicted performance capability during underground face haulage tests. Dust did not Impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance Closed loop steering control with manual override is recommended o: mended for the lateral guidance e system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.]

Jan 1, 1973

By Mark S. Stagg

Blast-induced ground vibrations from surface coal mine, quarry, and construction blasting were measured and analyzed for frequency content and duration characteristics. Eighteen commercially available ground vibration measurement systems were evaluated in the field and laboratory for linearity, accuracy, and crosstalk. Buried, surface, and sandbagged transducer placement methods were compared, along with peak and vector-sum measurements. The recommended minimum frequency ranges for ground vibration instrumentation are 2 to 150 Hz for coal mine and quarry blasting, and 5 to 200 Hz for construction and excavation blasting. When higher or lower frequency vibrations are possible, as in construction blasting or for a quarry shot close to a residence, care should be taken to insure proper choices of instrumentation and vibration criteria. Several instruments operating in these ranges are available, and all but one of the seismographs tested fell within ±3-dB accuracy limits (+41 pct, -29 pct). Waveform recordings of all three ground vibration components are recommended as the peak amplitude and frequency may vary among the three. Peak or vector-sum readings are adequate if only amplitude levels are desired. The soil density matched box should be anchored or buried, particularly for high-frequency, high-amplitude construction blasting.

Jan 1, 1980

By G. W. Jones

During the course of an investigation by the Bureau of Mines into the causes, behavior, end control of anthracite-line fires, it was observed that the carbon monoxide disappeared from a scaled fire area much more rapidly than could be explained oil the basis of leakage of gases. Two suggestions were offered for this high rate of disappearance; (1) That the carbon monoxide was oxidized at temperatures below 150° C, by either the anthracite or its ash (tests on many anthracites have shown that at temperatures above 150° C carbon monoxide is liberated in the oxidation products when air is passed through it); (2) that the carbon monoxide was oxidized by micro-organisms present in the sealed area.

Jan 1, 1939

By Floyd R. Hertweck

This Bureau of Mines publication contains analyses and related source data for 349 natural gas samples from 26 States and 2 foreign countries. The 3 samples from foreign countries and 339 of the U.S. samples were collected during calendar year 1983. The remaining seven samples were collected earlier, but releases granting permission to publish were not received until 1983. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of these investigations are published annually to make the information available to the petroleum industry and the general public. Twenty-seven publications have presented the results of 13,332 gas analyses made prior to 1983. The first three bulletins (1-3)3 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26-27) containing 8,104 analyses of sam¬ples collected since 1960.

Jan 1, 1984

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain t did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978