Search Documents

By Jr. Frank Parrish

This report describes the performance of 17 selected water-injection projects producing from Pennsylvanian-and Permian-age reservoirs. Illustrations depict reservoir structure and thickness, and production and injection history. A selected bibliography of publications pertaining to area oil recovery and geology is included. Tabulations of field and reservoir data reveal marked differences in the projects. Increased oil recovery resulted from injecting water in most cases; however, seven projects recovered less oil than the operators anticipated. Oil recovery by water injection ranged from 0.2 to 262 bbl per acre ft, or 0.1 to 22.5 pct of the initial stock-tank oil in place. Major reasons suggested for poor performance include: (1) Adverse directional horizontal permeability, (2) channeling of injected water through fractures or zones of high permeability, and (3) lack of containment of injected water. One 330-foot-deep project is among the first successful shallow water-floods in north Texas. Another project is the first successful Canyon sand-stone waterflood reported in the area. Previous gas injection in two Cisco sandstone projects did not prevent the reservoirs from responding favorably to waterflooding.

Jan 1, 1965

By Worthen Bradley

This paper describing the metallurgical practice and costs at the reduction plant of the. Sulphur Bank Syndicate, Clearlake, Calif., is one of a series of papers on the treatment of ores being prepared by the Bureau f Mines. The reduction plant and mine of the Sulphur Bank Syndicate are on the eastern shore of Clear Lake, in Lake County, Calif., 4 miles from the town of Clearlake and 125 miles north of San Francisco.

Jan 1, 1931

By Willard L. Hunter

The Bureau of Mines studied the effect of temperature upon the reduction of chromite by carbon and the relative reducibility of chromites as a function of their composition. Ferric oxide was also studied to provide comparative data. Pellets weighing approximately 1 gram and containing 70 percent ferric oxide, chromic oxide, or chromite and 30 percent graphite were subjected to closely controlled temperatures under a flow of argon for 15 minutes. The amount of CO and CO2 evolved was measured, and the reduced sample was analyzed by X-ray diffraction techniques. The reduction of Fe2O3 was studied over a temperature range of 600° to 1,400° C, while the reduction of Cr2O5 and chromite was conducted from 9000 to 1,621° C. The temperature above which appreciable reduction of Cr203 by graphite took place was 1,125° C. The temperature at which significant reduction started for three of the four chromite samples was approximately the same, indicating that there was concurrent reduction of iron and chromium oxides in the chromite mineral rather than selective reduction of iron oxides followed by reduction of chromic oxide. Rhodesian chromite appeared to dissociate at a lower temperature with concurrent reduction of iron. Based on the temperature at Which chromite was 50 percent reduced in 15 minutes, Transvaal chromite reduced most easily, followed by Mouat, then by Kampersian, and finally by Rhodesian DFC material. Statistical analysis of test results indicated that the ferric iron content of chromites affects their reduction behavior more than any other constituent.

Jan 1, 1966

By F. W. Wood

A program of research was conducted by the Bureau of Mines to investigate anomalies in electrical-discharge behavior during consumable-electrode arc melting of titanium and to study the effects of these irregularities on arc-furnace explosions. A major effort was devoted to an experimental survey of arc behavior and a qualitative definition of discharge phenomena.3/ An important conclusion was that the "glow" of industrial arc-melting terminology is not a glow discharge but a skittering arc in a displaced position. The conditions that permit displaced skittering were tentatively defined. The displaced skittering arcs tended to damage melting crucibles in two ways, and details of possible mechanisms leading to crucible rupture and explosive reactions have been proposed accordingly. However, no acceptable means of preventing crucible damage was discovered.

Jan 1, 1961

By Jon K. Ahlness

The Bureau of Mines investigated technologies for testing the integrity of in situ leach mining wells, as required by environmental regulations. To test for leaks, inflatable packers were used to seal the well casing. Laboratory testing determined that the packers could contain a casing pressure up to 50 to 60 psi (345 to 414 kPa) less than the packer inflation pressure. Single-and double-packer configurations were successfully field-tested in 32 wells ranging from 500 to 530 ft (153 to 162 m) in depth. A rigid pipeline and a hoist truck were used to run the packers in and out of the wells for the double-packer tests, which averaged 2-1/4 h each. In an effort to decrease the time of the rigid-pipe double-packer test. a self-contained trailer-mounted test system was designed and built. It utilizes a winch and steel cable to run the packers in and out of the well and high-pressure nylon tubing for packer inflation. This system was successfully field-tested in eight wells averaging 650 ft (198 m) in depth and resulted in a time savings of 13 pct and an operator-hour reduction of 42 pct.

Jan 1, 1985

By Morton Corn

The U. S. Federal Coal Mine Health and Safety Act of 1969 placed limits on the permissible concentration of airborne respirable coal mine dust. Evidence exists which suggests that the effects on health of respirable coal mine dust may depend on both host factors and dust properties other than concentration. Dust particle size, shape, density, specific surface area and chemical composition are among the dust parameters of interest in an epidemiological investigation of coal workers' pneumoconiosis and coal miner exposure to mine dust. The purpose of this investigation was to develop and demonstrate the feasibility of techniques to determine selected properties of respirable coal mine dust. An approved underground horizontal elutriator which samples air at 36 cfm was designed, fabricated and utilized in this study to collect respirable coal mine dust in three mines representing the Pittsburgh, Lower Freeport and Lower Kittanning coal seams. Analytical procedures for measurement of respirable dust sample particle size, density, random projected area, total surface area and chemical composition are presented. Results of analyses of three samples collected in each mine are presented. Up to five full work shifts of sampling were required to accumulate approximately five grams of respirable coal mine dust in each sample. Statistical tests were applied to determine the significance of differences between properties of dust samples collected in the same mine and between arithmetic mean values of dust properties representing three samples collected in each mine. A comparison was also made between

Jan 1, 1972

By Richard A. Allwes

The Bureau of Mines conducted an in-mine case study on two consecutive three-entry gate road systems designed in accordance with the stiff-yield pillar design concept. This Bureau study was conducted in order to further develop technology that will improve the health and safety aspects of longwall mining. Support loading and strata activity were monitored to determine the effects of retreat longwall mining on the gate road ground control system. Analyses of pillar stress and roof bolt loading histories revealed that headgate roof support elements ex-perienced cumulative loading throughout the life of the longwall panel. Tailgate pillar loadings had significantly different histories from the loading histories of the headgate pillars. Stress relief occurred in the tailgate pillars following the passage of the longwall face. More-over, the stiff-yield pillar design, with the abutment pillar placed adjacent to the working panel when part of the headgate system, provided effective ground control in that no major roof falls or roof problems were experienced in the headgate or tailgate systems during longwall mining.

Jan 1, 1985

By William H. King

The Nevada Massachusetts tungsten deposits (fig. 1) are in the Mill City Mining District in north-central Pershing County, Nev., about 37 miles southwest of Winnemucca. Contact metamorphism of thin limestone beds within a series of metamorphosed sedimentaries formed scheelite-bearing ore bodies. These deposits are distributed over a wide area. A Bureau of Mines development program was started January 11 d was completed on July 25, 1941. This work was centered on the outer and less explored beds in the district and comprised trenching, sampling, and diamond drilling. Exploratory work was done in cooperation with the U.S. Geological Survey. Project work substantially increased the reserve tonnage of marginal ore in three of the areas explored and proved the nonexistence of tungsten in a fourth area. The following pages summarize the history of the district, outline property ownership, and describe physical features and ore deposits. The plan and results of the work performed by the Bureau of Mines are presented along with geologic and topographic maps, assay maps, and diamond drill-hole logs.

Jan 1, 1950

By James Paone

Land utilized by the mining industry from 1930 through 1971 amounted to 3.65 million acres, or 0.16 percent of the land mass in the United States. Land reclaimed during the same period was 1.46 million acres, or 40 percent of the land utilized. This report includes data on land use for wastes from underground and surface mining, for wastes from mill operations, and on subsidence. Data on land use and reclamation were obtained from operating companies, mining organizations, appropriate State agencies, and others concerned with such activities. The 10 leading States in land used for mining in 1971 were, in decreasing order, Kentucky, Pennsylvania, Arizona, Ohio, California, Florida, West Virginia, Illinois, Minnesota, and Indiana. Mineral commodities accounting for a major portion of land use are, in decreasing order, bituminous coal, sand and gravel, stone, copper, phosphate rock, iron ore, and clay; for coal, these commodities are produced principally by surface mining operations. Reclamation over the 42-year period was largely on lands utilized for surface mining of bituminous coal. New surface mining methods, particularly for coal, incorporate some form of land restoration.

Jan 1, 1974

By T. F. Curry, L. B. Berger, H. A. Watson, S. J. Pearce

The conduct of work at elevated air pressures , such as in caissons and in tunnel - driving in subaqueous strata , poses safety problems not encountered in mining and tunneling operations at ordinary atmospheric pressure . This publication discusses some of the problems involved and presents information on the following subjects : ( 1 ) Physiological effects of gases at elevated pressure . ( 2 ) Use of respiratory protective equipment in rescue or recovery operations in event of fire or other emergency in pressurized tunnels . ( 3 ) Effect of elevated pressure on performance of some gasdetecting instruments ; interpretation of the results . Various types of respiratory protective devices are discussed in relation to their possible use at elevated pressures , especially the 2 - hour , selfcontained , recirculating - oxygen - breathing apparatus , which has had wide use in the United States during rescue and recovery work in the mining industry . A modified procedure that eliminates the hazard of oxygen poisoning enabling the safe use of this apparatus at elevated pressures , up to 45 pounds per square inch , gage , and tests to verify its practicability are described . procedure involves control of the partial pressure of oxygen in the breathing

Jan 1, 1964

By R. A. Guereco

Accurate measurements of physical dimensions of a section of stainless steel capillary tubing are presented and used to develop two final working equations for an absolute gas viscosimeter. The effects of pressure and temperature on these dimensions are considered. The internal surface finish and nonuniformity of the capillary bore are discussed, as well as entrance, kinetic energy, gas slippage, and gas compressibility correction factors.

Jan 1, 1967

By H. H. Schrenk

[There is a need for method of determining: benzene vapor in air which is simple and accurate and suitable for making industrial hygiene surveys. The most widely used method in this country is the modification of the Elliott and Dalton6/ procedure. This depends on the nitration of the benzene to reduction to phenylenediamine with all excesses of standard titanous chloride; solution, and titration with e standard ferric ammonium sulphite solution. This method has the disadvantages of being what time consulting: and cumbersome it requires considerable apparatus, and a special modification is necessary in the presence of toluene.]

Jan 1, 1935

By H. H. Schrenk

There is a need for a method of determining benzene vapor in air which is simple and accurate and suitable for making industrial hygiene surveys. The most widely used method in this country is the Smyth modification of the Elliott and Dalton procedure. This depends on the nitration of the benzene to m-dinitrobenzene, reduction to phenylenediamine with an excess of standard titanous chloride solution, and back titration with a standard ferric ammonium sulphate solution. This method has the disadvantages of being somewhat time-consuming and cumbersome; it requires considerable apparatus, and a special modification is necessary in the presence of toluene. Recently Cook and Ficklen have published a method based on the oxidation of benzene with hydrogen peroxide in the presence of iron salts. This method requires the use of solid carbon dioxide to freeze out the benzene. The reaction Which produces the color is complex; and only approximate quantitative estimations can be made, except in a very narrow range.

Jan 1, 1935

By Wilbur L. Webb

This publication reports on the design, fabrication and test of an Improved methane monitor system for compliance to 30CFR75.313. The system will Initiate automatic shutdown of mining machinery when excessive concentrations of methane are encountered. The prime consideration: In the design were small size, Improved accuracy and reliability, fast response and a transient resistant power supply capable of reliable operation from any mine power source. The power supply contains an internal battery that provides operating power to the detection system prior to mining machine start-up or after machine shutdown. This report documents the development program from conception through in-mine testing.

Jan 1, 1978

By H. M. Cooper

The determination of moisture in coal is an empirical test, because the time, temperature, and equipment are specified. The essential features of the equipment and details of the procedure are given in A.S.T.M. Designation: D271-44.:2. According to the specifications, the following features should be incorporated in the equipment used: 1. Oven must have uniform temperature in all parts. 2. Oven must be constructed with minimum of air space. 3. Oven must have means of changing the air two to four times per minute. 4. Air must be dried over sulfuric acid (sp. f-7. 1.84). The analytical procedures governing most of the nation's coal purchases are those given in A.S.T.M. Standards referred to above. These standards are general arid of such scope as to cover all ranks and types of coal. In cases where only the moisture is required, a faster method than the standard procedure is desired.

Jan 1, 1948

By Alexander May

The U.S. Bureau of Mines conducted studies to determine if phosphate slag stockpiles at Tennessee Valley Authority's National Fertilizer Development Center were hazardous materials. The stockpiles were not hazardous materials as determined by Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test. Radium-226 concentration was 28.7 pCi/g in slag and 2.1 pCi/g in background material. Radium-226 was not leached from the slag. Fluoride concentration was 3.87 pct in slag, 0.18 pct in subsurface material under slag, and 0.08 pct in the background. Slag material permeability was 1.65 x 10-3 cm/s, and subsurface material permeability was 3.24 x 10-6 cm/s. Rain water, trapped in a depression on top of the east slag stockpile, became seepage water at the base of the stockpile. Concentrations of EPA toxic elements in seepage water were much less than concentrations from an EPA EP toxicity test on the slag. Twelve elements-Na, Mg, Ca, Sr, Ba, Cr, Mn, Co, Cu, Cd, AI, and P-had higher concentrations in seepage water than in rain water on top of the slag stockpiles, or in creek water adjacent to stockpile bases, indicating that they were leached from slag stockpiles.

Jan 1, 1990

By Donald S. Colby

This Bureau of Mines report is essentially a handbook, or manual, for making the type of mineral resource valuation commonly required for such public policy problems as mineral leasing. The principle of resource valuation through the capitalization of cash flow is well established. A mathematical procedure, based on a simplified accounting system, is detailed for calculating cash flow from revenue, plant costs, and operating expense. Variations of procedure cover cost depletion, percentage depletion, and depletion limited to 50 percent of net income. The influence of the depletion provisions of the tax regulations on the value of a resource to an owner and to an operator is analyzed. The relationship of royalty, bonus payments, and sales price to resource value is also described, and methods for approximating resource values using these payments as input data are developed.

Jan 1, 1969

By Alexander M. Gow

This paper summarizes a survey of fine-grinding practice in ore-concentrating plants throughout the United States, Alaska, Canada, Mexico, and Cuba as reported in the Bureau of Mines Information Circulars on milling methods. The survey covers 49 concentrators, which have a combined capacity of over 160,000 tons per day. In these plants 470 ball, rod, and pebble mills prepare material for flotation, gravity concentration, amalgamation, cyanidation, and air separation. The ores are those of gold, silver, copper, lead, zinc, molybdenum, feldspar, and pyrite. The metallurgy is that of the period 1928-32. Of these 49 concentrators, 36 are in the United States. They can treat 134,400 tons per day, and they have 326 fine-grinding mills. In the United States there are about 100 active or temporarily idle concentrators, exclusive of the many plants in the Tri-State zinc district, the washeries of the Lake Superior iron ranges and the Florida phosphate area, and small gold and silver concentrators. These 100 plants have an estimated capacity of 290,000 tons per day and employ about 650 ball, rod, and pebble mills. Consequently, since this paper covers about half of the production of this country it may be considered as particularly representative of fine grinding in ore mills in the United States.

Jan 1, 1933

By E. M. SEELEY, F. S. LOTT

The total capacity of the natural-gasoline industry to produce light hydrocarbon products increased to 21,322,000 gallons ( 507,670 barrels ) daily on January 1 , 1948 , from 17,928,000 gallons ( 426,860 barrels ) daily on January 1 , 1946. Expansion of the industry in the first two post -war years , 1946 end 1947 , thus averaged 9 percent annually , compared with 6 percent annually in the last two war years , 1944 and 1945 . The number of cycle plants increased only from 37 to 39 in the years 1946 and 1947 , and total capacity of these plants gained 21 percent to 5,857,000 gallons de ily on January 1 , 1948 , represent ing 27.5 percent of the total capacity of the industry , compared with 27.0 percent on January 1 , 1946. All other plants decreased in number in the two-year period from 589 to 510 on January 1 , 1948 , but their total daily capacity increased 18 percent to 15,465,000 gallons . The daily capacity of the average plant in the industry was enlarged from 28,600 gallons on January 1 , 1946 , to 38,800 gallons on January 1 , 1948 , continuing the long -established trend to producing units of greater size and efficiency . The average cycle plant capacity increased from 131,000 gallons daily to 150,200 gallons daily on the same dates as the average capacity of all other natural -gasoline plants increased from 22,200 gallons to 30,300 gallons . Owing to the elimination of small , obsolescent plants in Illinois , Oklahoma , and Pennsylvania , these States experienced the greatest reductions in numbers of plants in 1946 and 1947. In Oklahoma and Texas , several consolidations of two or more plants into a single operating unit were reported . Louisiana and Mississippi were the only States in which the number of plants increased , but daily capacity to produce light products was larger in eleven States on January 1 , 1948, than two years earlier . Added facilities in California and Texas accounted for 41 and 36 percent , respectively, of the national gain in capacity .

Sep 1, 1948

By F. G. Schwartz

This circular presents the results of a survey of research on jet fuel thermal stability jointly sponsored by the National Petroleum Refiners Association (NPRA), Tulsa, Okla., and the Bureau of Mines. The development of supersonic planes has led to many problems that did not exist in the operation of subsonic aircraft. One of the most important of these is rapid deterioration of the fuel at the high temperatures to which it is subjected. At higher speeds, aerodynamic heating of the airframe imposes severe thermal problems, and conventional techniques of rejecting the heat to the atmosphere become impractical. The fuel is the only material present in sufficient bulk to be used as a heat sink. Thus, the fuel is subjected to aerodynamic heating and also is used to dissipate heat from lubricating oil, hydraulic fluid, electronic equipment, wheel wells, and cabin air. Consequently, the fuels may have to withstand both moderate temperatures for sustained periods in the fuel tanks and higher temperatures for brief periods during transfer from the tanks to the combustion chamber. Because of high temperatures, insoluble residue or gum may form in the fuel and contribute to heat exchanger fouling and to clogging of the fuel manifolds, nozzles, control systems, and other components of the fuel system.

Jan 1, 1962