Search Documents

By D. F. Malan, P. J. Le Roux

Almost no work has been published on the strength of pillars in mines exploiting the LG6/LG6A chromitite bands in the Western Bushveld Complex. The strength of these pillars is unknown, and the hard rock industry still uses the Hedley and Grant formula. Numerical modelling, using inelastic constitutive models, may be of some value in estimating the pillar strength, but this approach is difficult and prone to errors as many assumptions are made. This paper explores the alternative approach of the back-analysis of actual LG6/LG6A mining layouts, using displacement discontinuity codes to simulate the average pillar stresses on a mine-wide scale. From this, and underground observations, a ‘minimum’ pillar strength (K-value in the pillar strength formula) can be estimated. The codes TEXAN and Map3D are both used in the paper to simulate the actual pillar shapes and sizes in an LG6/LG6A mine. The results are encouraging as the two codes produced similar APS values for a complex pillar geometry. An estimated K-value of 77 MPa was determined for the LG6/LG6A pillars in this particular area. This is more or less similar to earlier work done for the UG2 chromitite seam, but higher than the K-value of 39 MPa for a linear formula obtained by other workers for LG6/LG6A pillars. Caution should therefore be exercised before using this higher value for all areas. The effect of element sizes and explicitly simulating the effect of the surface for shallow pillars is illustrated in the manuscript using both codes. The need for actual pillar observations and an iterative design process, which cycles between modelling and observations, is also emphasized.

Nov 27, 2024

By D. M. Poulter, J. N. Brooke, P. H. Williams

"The complexity of the mining and metallurgical operations of Nchanga Consolidated Copper Mines, Limited, has made it necessary to use computer-assisted planning techniques in order to maximize copper production and marginal contribution to profit. The most successful of the Group Production Scheduling systems utilized linear programming to optimize the concentrate routing only. This third-generation system was commissioned in March, 1968.It bad become necessary by March, 1970, to expand the long-term planning activities and to take into account new mines and new concentrate treatment schemes. Technical difficulties and manpower limitations made it impossible to expand the third-generation system, and it was decided to construct a new Group Production Scheduling system using only linear programming.The plant models in the new fourth-generation system are based on data available from the monthly reports of the metallurgical plants. The models consist of mass balances and empirical relationships. Matrix coefficient assignment and management reports are produced using a Report Generator Language designed for linear programming data files. The development of this system is an example of a user application of a system package."

Jan 1, 2014

By M. Ericsson

?Rare earths ?will not be bargaining instruments?? was stated in a headline in China Daily of 29 October 2010. The Chinese government is trying to fend off the persistent accusations from Japan, the USA, and Europe that it is manipulating the supply of these so called ?critical? metals to gain political and economic advantages. The critics maintain that China has taken the rest of the world hostage by controlling 97% of the resources of rare earths. These elements are crucial in a number of high-tech applications. They are not impossible to substitute, but difficult to do so effectively. The name ?rare earth? is a misnomer, as even the least abundant is 200 times more common in the Earth?s crust than gold. They are, however, difficult to find in economic concentrations. The Chinese near-monopoly over the rare earths, together with China?s scramble for other resources in Australia, Africa, and elsewhere around the world, is seen as an example of a Chinese strategy to take control of vital metal resources. The Chinese are also accused of using unfair and sometimes illegal business practices in this fight for resources. Practices which, critics claim, put the Chinese interests above the interests of the host countries, in particular in Africa.

Jan 1, 2011

[Council for 1993/94 President Dr H. Scott-Russell President Elect J.A. Cruise Vice Presidents Senior D.A.J. Ross-Watt Junior P.D.K. Robinson Immediate Past President J.P. Hoffman Honorary Treasurer J.A. Cruise]

Jan 1, 1994

By D Olivier

De Beers' Finsch Mine is situated in the Northern Cape province, 170 km northwest of Kimberley. The concentrator facility, designed and constructed by Bateman Engineering, was commissioned in 1967 and upgraded in 1979 using diamond liberation and extraction technology available at the time of design. Since then significant advances in diamond processing and technology have been made and these -have been incorporated into the new main treatment plant and recovery plant flowsheets, making diamond liberation and recovery from the Pre-1979 dumps a viable economic option at Finsch."

Jan 1, 2010

By D. Sethuram, P. G. Koppad, S. Iyengar, R. Shobha

TiB2 and CeO2 particle-reinforced Al6061 hybrid composites were manufactured using stir casting and hot rolling techniques. The base alloy and composites were hot-rolled at 500ºC and a 50% reduction was achieved through 12 passes. The effect of varying TiB2 and CeO2 particle additions on the microstructure and mechanical properties of the Al6061 matrix was studied. Scanning electron microscopy showed uniform dispersion of both the reinforcements, with good interfacial bonding. Microhardness and tensile properties like yield and tensile strength were found to be higher for hybrid composite with 2.5% TiB2 and 2.5% CeO2 compared to Al6061 alloy and other hybrid composites. The increased tensile strength is attributed to good dispersion and interfacial bonding between the particles and Al6061 matrix. Fracture analysis using a scanning electron microscope revealed ductile fracture for the Al6061 alloy and mixed characteristics of ductile-brittle fracture for hybrid composites

Oct 1, 2021

By G. Sánchez, S. Seiler, B. Klein, T. Cebeci, P. Bradshaw

The Decar Nickel District is a greenfield discovery by FPX Nickel Corp., of nickel mineralisation located in central British Columbia (BC), Canada. The Baptiste deposit is part of the Decar Nickel District and is a unique deposit containing a nickel-iron alloy mineral called awaruite, with over 2-billion tonnes of inferred resource grading 0.12% Davis Tube Recoverable (DTR) nickel. This deposit represents a significant nickel resource. Awaruite is a high density and ferromagnetic mineral, which could be recovered, along with magnetite that is also present in the samples, using magnetic separation. However, there is still a lack of understanding of the properties of the awaruite and its metallurgical response. This information is imperative for the set-up of the variables involved in its concentration. The aim of this paper is to show and discuss the effect of magnetic field strength for the recovery of nickel from Baptiste deposit samples. Magnetic separation at bench and pilot scale with different magnetic field strengths is evaluated as a concentration method for awaruite. Mineralogical information is provided to support the results and also to briefly assess the variability of DTR nickel within the deposit. The Baptiste deposit is unique and will benefit from a sound scientific understanding of the process solution as well as other ongoing work. If successful, the outcome will lead to the development of a mine. With greater than 2-billion tonnes of inferred resource, the mine would represent a significant new source of nickel globally. Keywords: Nickel ore processing, magnetic separation , awaruite, magnetite

Jan 1, 2020

By R. Koen, H. Visser, A. Roodt

"SynopsisThe tetraethylammonium salt of the mono-anionic coordination compound mer-oxidotrichlorido(thenoyltrifluoroacetylacetonato- K2O,O’)niobate(V) (NEt4)[NbOCl3](ttfa)], has been prepared under aerobic conditions and characterized by single-crystal X-ray diffraction. (NEt4)[NbOCl3](ttfa)] crystallized in the monoclinic P21/c space group, with a = 11.483 (5), b = 12.563 (5), c = 17.110(5) Å, and ß = 100.838 (5)o. The complex structure exists in a 50.0% (NbA) : 50.0% (NbB) positional disorder ratio.IntroductionComplexes containing organometallic type ß- diketone ligands with O,O and O,N donor atoms are used widely in coordination chemistry and have applications in catalysis, radiopharmaceuticals, etc. (Schutte et al., 2011; Roodt, Visser and Brink, 2011; Brink et al., 2010; Otto et al., 1998). These ligand systems are very useful because of their highly coordinative nature, high solubility, and also due to their ability to be functionalized with various substituents on the carbonyl carbon atoms (Schutte et al., 2011).Only a small number of ß-diketonate ligands have successfully been coordinated to a Nb(V) metal centre, with only a select few being characterized by X-ray crystallography (Viljoen, 2009; Bullen, Mason and Pauling, 1965; Preuss, Lamding and Mueller-Becker, 1994; Funk, 1934; Davies, Leedlam and Jones, 1999; Allen, 2002. The synthesis and crystal structure determination at room temperature of mer-oxidotrichlorido (thenoyltrifluoroacetylacetonato- k2O,O’)niobate(V) {(NEt4)[NbOCl3(ttfa)]} was first reported by Daran et al. in 1979. Accordingly, for this current investigation, (NEt4)[NbOCl3(ttfa)] was re-evaluated at 100 K to determine if the structural features might change with temperature."

Jan 1, 2015

By M. Matabane, T. Khati

"Accurate delineation of the contact between a kimberlite pipe and country rock at production level depths is a challenge due to limited geological data. Geological information is obtained from widely spaced diamond core boreholes which are drilled either from surface or from higher mining levels within the pipe. Kimberlite pipe/country rock contacts are notoriously irregular and variable, further reducing the confidence in contact positions defined by the drill-holes. At Finsch Diamond Mine (FDM), the opportunity arose to further improve the confidence in the contact positions relative to the planned slot (end) positions of each sublevel cave tunnel during the development stage of these tunnels. As a result, the accuracy of the 3D geological model has improved.The use of diamond drill core for this purpose is expensive due to site establishment requirements. The lengthy time taken during site establishment also delays the development of tunnels and support cycles, thereby extending the completion dates. FDM has reduced delays during development by adopting percussion drilling, in conjunction with gamma ray logging. The S36 drill rig is mounted on a moveable platform and does not require a costly and lengthy site establishment. The holes are generally drilled (0°/flat) on grade elevation, and these holes could also be drilled from the rim tunnels (developed in waste) into the kimberlite pipe. A single-boom production drill rig is normally used to drill holes about 20 m in length.On completion of the contact delineation drilling, gamma logging of the holes is conducted using the GeoVista geophysical sonde (or probe) to log the natural gamma signature of the dolomite/ kimberlite contact. The advantage of this tool is that the readings are continuous within centimetre intervals, and due to contrasting characteristics between kimberlite (rich in clay minerals) and dolomite, the contact position can be determined accurately. The better definition of contact positions also adds value to tunnel stopping distance in terms of developing the tunnel’s slot at the optimum distance from the contact (easier blasting of longhole rings, avoidance of contact overbreak and premature waste ingress, and other matters relating to extraction of ore from these tunnels). This method is highly successful and has reduced development costs (on-time completion), improved definition of the pipe’s contact position for geological modelling, improved blast design, and mitigated early waste ingress by maintaining the contact’s integrity."

Feb 1, 2019

By J. Hadjigeorgiou, J. Wesseloo

Mining companies employ a multitude of risk management tools. The effectiveness of these tools for decision-making and communicating risk has not been addressed. This paper investigates the use of verbal probabilistic expressions in communicating geomechanical risk. Analysing survey data obtained from a group of mining geomechanics professionals, it identifies limitations of common probabilistic expressions. The paper concludes by making specific recommendations to avoid the use of certain expressions that may result in increased uncertainty, thus compromising the use of risk management tools.

Jan 30, 2026

By M. A. Mahboob, T. Celik, B. Genc, I. Atif, S. Ali

"Mapping of hydrothermally altered areas, which are usually associated with mineralization, is essential in mineral exploration. In this research, open source reflectance spectroscopy data from the multispectral moderate-resolution Landsat 8 satellite was used to map altered rocks in the Gauteng and Mpumalanga provinces of South Africa. The unique spectral reflectance and absorption characteristics of remotely sensed Landsat data in the visible, near-infrared (NIR), shortwave-infrared (SWIR) and thermal infrared (TIR) regions of the electromagnetic spectrum were used in different digital image processing techniques. The band ratios (red/blue, SWIR 2/NIR, SWIR 1/NIR), spectral band combinations (Kaufmann ratio, Sabins ratio) and principal component analysis (Crosta technique) were applied to efficiently and successfully map hydrothermal alteration minerals. The results showed that the combination of spectral bands and the principal component analysis method is effective in delineating mineral alteration through remotely sensed satellite data. The validation of results by using the published mineral maps of the Council for Geoscience South Africa showed a good relationship with the identified zones of mineralization. The methodology developed in this study is cost-effective and time-saving, and can be applied to inaccessible and/or new areas with limited ground-based knowledge to obtain reliable and up-to-date mineral information.IntroductionMany developing nations depend on exploration and exploitation of mineral resources to sustain their economic growth. Usually, the traditional mineral exploration techniques require enormous finances, prolonged time, and tremendous manpower, particularly in areas that are not easily reachable (Maduaka, 2014). Furthermore, mineral exploration required state-of-the-art techniques and expertise along with geological, geochemical, and geophysical datasets, which may not be easily available or may be lacking where access is problematic (Kaiser et al., 2002; Bemis et al., 2014). Modern remote sensing technology has proved to be one of the highly efficient and robust techniques used for mineral exploration. The use of remote sensing satellite images for geological mapping and mineral exploration usually involves studying the physicochemical properties of rocks and weathering soils, such as mineralogy, landforms, geochemical signatures, and the spatiall distribution of lineaments (Bhattacharya et al., 2012)."

Mar 1, 2019

By C. A. Snyders

This paper investigates the recovery of platinum group metals (PGMs) from a dilute cyanide leach solution containing base metals, in a manner similar to that used for gold extraction in a typical CIP process, and focuses on both the adsorption and elution stages. The carrier-phase extraction of precious metals using activated carbon offers significant advantages over other processes in terms of simplicity, the high pre-concentration factor, rapid phase separation, and relatively low capital and operating costs. As a sorbent, activated carbon is still by far the most important material because of its large surface area, high adsorption capacity, porous structure, negligible environmental toxicity, low cost, and high purity standards. Adsorption tests were performed on a pregnant alkaline leach solution (0.15 ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) resulting from cyanide extraction performed in column leach tests. The initial adsorption rates of platinum, palladium, and gold were very fast and recoveries of these three metals were approximately 90 per cent after 2 hours and 100 per cent, 97.4 per cent, and 99.9 per cent respectively after 72 hours. The parameters that influence the extraction of PGMs and Au were examined to assess their relative importance during the adsorption process in order to provide the basis for process optimization. The concentration of thiocyanate was not identified as significant factor for PGMs adsorption, while nickel concentration was the most significant extraction process parameter. Base metal cyanide complexes adsorb and compete with the PGM complexes for sites on activated carbon, and while copper adsorption can be minimized by adjusting the residence time, nickel adsorbs at approximately the same rate as that of the PGMs, influencing the loading capacity and adsorption kinetics of the PGMs. The feasibility of eluting platinum and palladium cyanide complexes from activated carbon using an analogue of the AARL process was investigated. Platinum and palladium elute from activated carbon almost to completion in 4 to 5 bed volumes at 80°C, while the elution of gold at this temperature is slow, with a significant amount of gold still to be eluted after 16 bed volumes. Cyanide pre-treatment was found to have a significant influence on PGM elution. Higher cyanide concentration in the pre-treatment step results in more efficient elution up to a point, and experiments suggest the possibility of an optimum cyanide concentration, beyond which elution efficiency starts decreasing.

Jan 1, 2012

By Wilson. D.

The Vaal Triangle Branch of The South African Institute of Mining and Metallurgy was established on 20th November, 1986, at a meeting enthusiastically supported by local members. In attendance were special guests Dr H. Wagner (President, SAIMM) and Dr O.K. H. Stefen (Junior Vice-President, SAIMM).

Jan 1, 1987

By J .. F. Brownrigg

In the mining method used at O'Okiep Copper Company (OCC), vertical crater retreat, the prime requirement for the fill is that it should be sufficiently strong to be free-standing to a height of 150 m. Other requirements are minimal decant and drainage water, and high pulp density to allow large tonnages to be placed quickly and alleviate transport problems. The excessively high cost of cement precluded the use of a cement-based fill, and after three years of extensive investigations a backfill based on the smelter slag was produced. Currently a fill with a uniaxial compressive strength of greater than 1 000 kPa after one month is being produced. This is in excess of the design specification of 850 kPa after 2 - 3 months. The research and development which went into the slagfill is briefly covered; the production of the fill from the various raw materials is described; and the design and control systems of the backfill plant, the reticulation system and its monitoring are examined. Finally, the implications of this high- quality fill for the mining programme are assessed.

Jan 1, 1988

The AMIRA Code of Practice and Guidelines for Metal Accounting was developed in response to demand from a number of sponsor companies, including one major platinum producer. Since its publication in 2007, the Code has become widely accepted in the mining industry world-wide as a guide for best practice in metal accounting. With the changes in the structure of the platinum mining industry in South Africa over the last 10 ? 15 years, in particular, the starting up of a number of small platinum producers who must have their concentrate smelted and the contained valuable metals refined by third parties, the need for metal accounting systems that are accurate and have an acceptable level of precision has become even more critical to the success of a platinum-producing operation. The current state of metal accounting in the industry is discussed and possible areas for improved accounting and associated metallurgical efficiencies are identified.

Jan 1, 2012

By L. G. Austin

The paper summarizes the current state of development of simulation models for SAG and FAG mills, and gives the results of recent investigations of the physical processes occurring in autogenous grinding. The breakage process is treated as the sum of three regions of breakage actions: normal breakage caused by nipping of particles between media (steel balls or pebbles); abnormal breakage caused by media when the particle or lump is too big in relation to the media to be readily nipped; and self-breakage resulting from the chip¬ping fracture and abrasion of the tumbling action of rock lumps. Each region of breakage action has associated specific rates of breakage and primary progeny fragment distributions. A simplified form of the model was used to predict the performance of an 8 m diameter SAG mill with L/D = 0.5 grinding a copper ore, and predicted maximum capacity and minimum kWh/ton at about 6% ball load at 25% total filling. Two FAG mills of L/D = 2 were necessary to give the same capacity, and the simulations indicated a lower kWh/ton for these mills. For this ore, both systems were technically feasible.

Jan 1, 1987

The wage structure of graduate White men in 1979, by Adri Kruger, Pretoria, Human Sciences Research Council, 1979.76 pp. R5,00. (Reviewer: D. G. Malan) Financial Times mining international yearbook, edited by WilIiam G. Nightingale. London, Longman, 1980. 750 pp. £24 by surface, £34 by air. (Reviewer: J. D. Austin) Techniques in mineral exploration, by J. H. Reedman. Barking (U.K.), Applied Science Publishers, 1979. 533 pp. $90. (Reviewer: D. L. Kyle) Practical geostatistics, by Isobel Clark. Barking (U.K.), Applied Science Publishers, 1979. 129 pp. £13,75. (Reviewer: D. G. Krige) Uranium: The balance of supply and demand 1978- 1990, by the Uranium Institute. London, Mining Journal Books, 1979. 61 pp. £8,50 by surface,,£9,25 by airmail. (Reviewer: D. J. Crowe) Wear and abrasion in industry The South African Institute of Mining and Metallurgy and the Institution of Metallurgists (South African Branch) is to hold a colloquium on the topic of wear and abrasion of metals in February 1981. Steel rolling The International Conference on Steel Rolling sponsored by The Iron and Steel Institute of Japan will be held in Tokyo, Japan, from 29th September to 4th October, 1980.

Jan 1, 1980

By I. H. Clark

A variety of backfills is presently being placed in different gold mines. The backfills are pumped as slurries to stopes where they are discharged into some form of retaining paddock. The effectiveness of fill as a support medium will depend on a number of factors. These can largely include (i) inherent properties of the material, e.g. particle size, shape, distribution and com- position, and (ii) conditions of placement. The terminology required for describing backfills is introduced, and the various laboratory-measured properties are presented for a variety of fills. Finally, the properties of the fills as they are placed underground are discussed.

Jan 1, 1988

By J. H. van Laar, L. J. van der Walt, P. L. Crouse, H. Bissett, G. J. Puts

"SynopsisSilicon carbide nanopowders were produced using a microwave-induced plasma process operating at 15 kPa absolute and at atmospheric pressure. Methyltrichlorosilane (MTS) served as precursor, due to its advantageous stoichiometric silicon-to-carbon ratio of unity, allowing it to act as both carbon and silicon source. Argon served as carrier gas, and an additional hydrogen feed helped ensure a fully reducing reaction environment. The parameters under investigation were the H2:MTS molar ratio and the total enthalpy. The particle size distribution ranged from 20 nm upwards, as determined by SEM and TEM micrographs. It was found that an increase in enthalpy and a higher H2:MTS ratio resulted in smaller SiC particle sizes. The adhesion of particles was a common occurrence during the process, resulting in larger agglomerate sizes. SiC layers were deposited at 15 kPa with thicknesses ranging from 5.8 to 15 µm.IntroductionIt is well known that methyltrichlorosilane (CH3SiCl3 or MTS) decomposes to form silicon carbide (SiC) and hydrogen chloride (HCl) as shown in Equation [1]. The reaction kinetics and mechanisms for this reaction are thoroughly reported in the literature (Sone et al., 2000; Papasouliotis and Sotirchos, 1999; Kaneko et al., 2002; Wang et al., 2011)."

Jan 1, 2015

By H. Manurung, I. M. Bendiayasa, W. Astuti, and H. T. B. M. Petrus, F Anggara, K. C. Wanta

The leaching kinetics of cerium (Ce) and yttrium (Y) in sodium-hydroxide-digested non-magnetic coal fly ash using acetic acid were investigated. The variables analysed were pH, solid-to-liquid ratio (S/L), and temperature. The results show that cerium and yttrium's maximum recovery was 57.33% and 58.36%, respectively, under leaching temperature of 90°C for Ce and 60°C for Y at pH of 1,74 and 10 g/mL solid-liquid ratio in 240 minutes. Increasing the leaching time to more than 120 minutes did not significantly improve the results. After the magnetic separation process, the ICP-OES analysis shows a slight increase in the concentration of cerium and yttrium on nonmagnetic components. The XRD and ICP-OES analysis for the sample before and after silicate digestion shows that 40% silicate was dissolved. The calculation of apparent activation energies of leaching using the Arrhenius law for the leaching of cerium and yttrium gives 22.72 kJ/mol and 35.84 kJ/mol, respectively. The kinetic leaching model of cerium and yttrium all fit Dickinson's new shrinking core model. The calculation results show that the leaching reaction is controlled by combining interface transfer and diffusion across the product layer.

Nov 6, 2024