Search Documents

By S. Tu, Y. Yuan, H. Wei, Z. Chen, M. Jia

"To reduce production costs and increase efficiency in ageing coal mines, a system that utilizes two shearers in a fully mechanized longwall working face is proposed. Using theoretical and engineering experience, three issues pertaining to the system were determined: (a) the two-shearer mining technique; (b) matching and modifying the equipment; (c) and coal-cutting task allocation for each shearer. Two mining processes are proposed, with the two shearers travelling in either the same or opposing directions. To avoid breakage of chains and pan extrusion of the armoured face conveyor (AFC), the length of the AFC ‘snake’ was controlled. To ensure continuous cutting and transporting of coal, the cross-sectional dimensions of the AFC were checked and the shearer closer to the head drive was modified. Based on the assumption of equal cutting times for each shearer, the meeting position of the two shearers was obtained by using a theoretical model of mining task allocation. Application of this technique at No. 2 Jining Mine, China, has shown remarkable benefits: daily production capacity was increased by 54% and personnel efficiency was improved by 33 t/d per person. IntroductionAll coal mines aim to increase the unit output of the working face to reduce mining costs and improve the economic efficiency of the operation. To achieve this goal, a production model known as one mining face of the mining area has been adopted by most Chinese coal mines (Hu, Meng, and Zhu, 2008; Zhang, Zhang, and Wang, 2000). Under these conditions, the main technical approaches to maximize the output are increasing the width of the working face (Qu, Xu, and Xue, 2009) and accelerating the advancing speed (Robbins, 2000). In coalfields with shallow seams, the width of a fully mechanized face exceeds 300 m (Ju and Zhu, 2015; Fu, Song, and Xing, 2010); in coalfields with deep seams, the width of the face is usually greater than 240 m (Liu et al., 2016; Li et al., 2013). The term ‘super-long working face’ was proposed to describe working faces with a width of over 240 m (Zhao and Song, 2016; Xu et al, 2007) in China. To support these long working faces with rapid advancing speeds, high-powered mining equipment is required (Kulshreshtha and Parikh, 2001, 2002; Tu et al., 2009; Mishra, Sugla,and Singha, 2013). This is easily achieved in newly built mines, but is not a good choice for ageing mines because of the low return on a high investment on account of the limited remaining resources. It is therefore difficult for ageing mines to significantly increase their unit output with the existing mining equipment. This study focused on this problem: two shearers were applied to a longwall fully mechanized working face (LFMWF) to achieve increased unit output."

Oct 1, 2018

By J. P. Harrison, J. A. Hudson.

ABSTRACT: When considering the rock stress component of rock mechanics design, the basic procedure is to consider the pre-existing stress-state in the rock mass and then estimate the disturbance to this stress state as a result of engineering excavation. Failure criteria are applied to the final stress state to establish whether failure will occur. However, during the evolution of the stress state, the failure locus may be reached before the anticipated failure state and, in this case, failure will occur unexpectedly. This indicates that the complete stress path (defined as the variations in magnitudes and orientations of the stress tensor components resulting from engineering-induced or natural changes) must be considered. We list a set of stress path principles with their corollaries and then introduce a new and powerful method for simultaneously illustrating changes in the six independent components of the stress tensor. This method plots the magnitudes of the principal stresses above their orientational paths on the hemispherical projection, to provide a three-dimensional stress path locus for each of the three principal stress components. In connection with this presentational device, we illustrate a number of concepts associated with the stress path in rock engineering. For example, we show how the minor principal stress approaches zero at an unsupported excavation face, the interchange of the trajectories of two principal stresses when their magnitudes become equal, and the influence of the bounds on the principal stresses given by strength criteria. RESUME: Si on s’interesse à la composante “contrainte” lors d’un dimensionnement en mécanique des roches, la méthode de base consiste à considérer l’état de contrainte pré-existant dans le massif rocheux, puis d’estimer la perturbation à cet état générée par l’excavation projetée. Des critères de rupture sont appliqués à l’état de contrainte final pour établir si une rupture va se produire. Cependant, lors de l’évolution de l’état de contrainte, la surface critique peut être atteinte ce qui provoquera une rupture anticipée et, dans ce cas, cette dernière sera inattendue. Cela indique que le chemin de contrainte complet (défini par les variations de l’intensité et de l’orientation des composantes du tenseur des contraintes liées à des causes anthropiques ou naturelles) doit être pris en compte. Nous présentons un ensemble de règles pour les chemins de contraintes ainsi que leurs corollaires et, ensuite, nous introduisons une méthode, nouvelle et puissante, pour présenter simultannement les changements des six composantes du tenseur des contraintes. Cette méthode consiste à tracer l’intensité des contraintes principales sur le chemin d’orientation des contraintes à l’aide d’une projection hémisphérique afin d’obtenir le lieu, en trois dimensions, de chaque contrainte principale. En relation avec cet outil de représentation, nous illustrons certains concepts associés au chemin de contrainte en ingénierie au rocher. Par exemple, nous montrons comment la contrainte mineure tend vers zero à la surface d’une excavation sans soutenement, le changement de direction des deux contraintes principales quand leur intensité deviennent égales, et l’influence des conditions aux limites sur les contraintes fournies par un critère de rupture. ZUSAMMENFASSUNG: Bei ingenieurmassigen Taetigkeiten in Felsgesteinen ist es noetig die ungestoerten Gesteins Stress Componenten, die vor einem anthropogen Eingriff im Gestein vorhanden waren, zu kennen und erst dann Vorhersagen ueber Stoerung des Stress Zustandes, der durch einen ingenieurmaessigen Eingriff hervorgerufen wird, herzuleiten. Kriterien fuer das Versagen werden im letzten Stadium, des Stress Zustandes angewendet, um zu erfahren ob ein Versagen wohl eintreten wird. Es ist jedoch zu beachten, dass waehrend des Stress Aufbaus ein oertliches Versagen eintreten kann, welches vor dem eigentlichen, erwarteten Versagens Zustand auftritt. Diese Moeglichkeit weist darauf hin, dass der gesammte “Stress Path” (definiert durch die Variationen der Stress Tensor Komponenten in Richtung und Groesse, hervorgerufen durch ingenieurmaessig hervorgerufene oder natuerlich Vorgaenge) betrachtet werden muss. Wir fuehren eine Liste der “Stress Path” Prinzipien auf und stellen dann eine neue und wirksame Methode zur gleichzeitigen Darstellung der sechs unabhaegigen Komponenten des Stress Tensors vor. Diese Methode stellt die Groesse der “Principal Stresses” in Abhaengigkeit von ihrem rauemlichen Weg auf einer hemispherischen Projektion dar und erlaubt hiermit eine drei dimensionale Darstellung fuer jeden Ort des “Stress Path’s” in die drei Haupt Stress Komponenten. Im Zusammenhang mit der hier gegebenen Darstellungsart, verdeutlichen wir eine Reihe von Konzepten in der Felsmechanik. Wir zeigen zum Beispiel, wie der “Minor Principal Stress” Null zustrebt an einer Wand von einer nicht abgestuetzten Ausschachtung, den Austausch von Trajektorien zweier “Principal Stresses” wenn ihre Groessen sich gleichen, und den Einfluss der Groesse von “Principal Stresses” bei gegebenen Kriterien des Festgkeits Versagens.

Jan 1, 2003

By C. Musingwini, C. Beaumont

"Kansanshi mine, located in northwestern Zambia, uses conventional openpit mining to produce primarily copper, with gold as a by-product. The ore is extracted from a deposit with highly complex mineralogical suites that are difficult to process, sometimes leading to poor recoveries. The mine was using an ore classification system called ‘Mat-Type’, which classified various ore types into 22 different quality categories, ranging from poor to good quality. Ore with poor recovery was classified as ’poor quality’ ore and directed to long-term stockpiles. Due to a lack of proper integration between the technical and functional areas forming the mine value chain, Mat-Type unintentionally misclassified ore. A geometallurgical analysis was therefore undertaken to review Mat-Type and a new geometallurgical ore classification system, called ‘OXMAT ’, was developed to replace Mat- Type.When implemented, OXMAT eliminated nine of the 22 ore categories and the remaining 13 ore categories could now be more accurately and consistently defined, leading to a significant change in the quantity of ore being mined. OXMAT demonstrated that within a defined test volume of the geological model, waste tonnes could be reduced by 19% while ore tonnes could be increased by 17%. This paper therefore demonstrates the value created through integrated geometallurgical modelling. IntroductionKansanshi mine is located in northwestern Zambia, approximately 10 km north of the provincial capital Solwezi and about 160 km west of Nchanga mine in the Central African Copperbelt (Broughton and Hitzman, 2002). The location of Kansanshi mine relative to other major copper deposits in the Copperbelt is indicated in Figure 1.Kansanshi mine uses conventional openpit mining methods to exploit copper- and gold-bearing veins hosted in a structurallycontrolled mineral deposit. Mining is carried out in two areas of the deposit, the Northwest and Main pits. A third area of the deposit, called Southeast Dome, is currently not being exploited (Figure 2)."

Mar 1, 2019

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installationof LBs remains a challenge. In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installation of LBs remains a challenge.In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By M. D. Raganya

The Kriel Colliery is an Anglo Coal mine which is contracted with Eskom to produce No. 4 seam for Kriel power station. The mine previously found it uneconomical to mine No. 5 seam due to the low qualities and tonnages of the seam, both at the opencast and underground sections. An area has been encountered for the first time at Kriel Colliery opencast pit 5, where the tonnage and qualities of No. 5 seam warrant further investigation. The primary reason for the investi¬gation of No. 5 seam by Kriel Colliery is because of the advantage of the high selling price (R450/t) that the market is currently prepared to pay for the No. 5 seam. The aim of this project is to mine No. 5 seam economically without interrupting No. 4 seam mining operations. The problem is that the equipments that are currently being used at the mine belong to Eskom and are dedicated to mining No. 4 seam only, not No. 5 seam. Through geology investigation, it is found that the whole No. 5 seam (No. 5 seam upper and lower) has an average thickness of 1.8 m. It also contains a parting of carbonaceous shale which divides the seam into two parts. No. 5 seam upper contains less tonnage compared to No. 5 seam lower. The calorific value and ash content of No. 5 seam lower is far better than No. 5 seam upper, but would still require washing the coal. This makes No. 5 seam lower the preferred seam to mine because it meets the requirements of the customer which is Highveld Steel. It is a coincidence that the area containing No. 5 seam under investigation encounters high overburden problems. The problem of drilling to No. 4 seam was going to be encountered because the thickness of the overburden ranges from 35 to 39 m. The Gardner Denver at the mine can drill blastholes only to a depth of 34.5 m, meaning the full overburden will not be drilled at once. This means the mining of No. 5 seam will do favours for Eskom because the overburden thickness will be minimized. This then led to an agreement between Anglo Coal and Eskom to mine No. 5 seam because both companies benefit from the project. In order to identify a suitable mining method for No. 5 seam lower, literature studies took place. It is found that San Juan mine from the USA has similar geological features to Kriel Colliery's No. 5 seam. Through comparisons, it is found that truck and shovel mining would suit the geology of Kriel Colliery's No. 5 seam since San Juan mine is using it. The sequence of mining No. 5 seam lower allows for a clearance of two cuts between the truck and shovel operation and the dragline. The mining sequence of No. 5 and 4 seam will be in the order of top soil removal; soft overburden pre-stripping; pre-strip drilling; pre-strip hard overburden; No. 5 seam lower coaling; interburden drilling and blasting; interburden stripping and No. 4 seam coaling. Financial evaluation of the project shows that a contractor will charge Kriel Colliery (Anglo Coal) approximately R 102.2 million to mine No. 5 seam successfully. The sales of No. 5 seam lower will provide a profit of R99.4 million at a yield of 70% from the washing plant. The project is beneficial to both Eskom and Anglo Coal because Eskom will have eliminated the problem of pre-stripping and Anglo Coal will generate additional profit. Through investigation and analyses of the project, it is proven to be viable and should take place. This is after looking at the advantages that the project has for Anglo Coal and Eskom. Keywords No. 5 seam, truck and shovel mining, Kriel Colliery, No. 5 seam mining at Kriel Colliery opencast, Anglo Coal and Eskom, No. 5 seam upper and lower, top soil removal, soft overburden pre-stripping, pre-strip drilling, pre-strip hard overburden, No. 5 seam lower coaling, interburden drilling and blasting, interburden stripping, No. 4 seam coaling.

Jan 1, 2011

By B. K. Loveday

A Colloquium on 'Control and Simulation in the Minerals Industry' was held at the Holiday Inn, Milner Park, on 20th September, 1984, in conjunction with the Electra Mining Exhibition. A total of 170 persons attended the very full morning programme, which began with an opening address by the President, The South African Institute of Mining and Metallurgy, Mr l.D. Austin. He outlined the reasons why computers were being used to an ever-increasing extent for control and simulation in the minerals industry. The computer was even used to check, among other things, the validity of the signals it was receiving by mass-balance calculations.

Jan 1, 1985

By T. Szendrei, S. Tose

The fracturing and movement of rock that occurs in the vicinity of a stemmed borehole charge in open pit mining operations are described by examining the effects of the emitted stress waves – shock and elastic – and the expansion of high-pressure detonation product gases. Three principal modes of momentum transfer to fractured rock are identified, all linked to gas expansion work. This work can be delivered radially (burden), axially (stemming), and in the collar zone (cratering). Flyrock is generated under unusual combinations of blast parameters and rock properties. Although infrequent and seldom predictable, the generation of flyrock can nonetheless be interpreted and modelled in terms of the principal mechanisms of rock projection described in this study. The physical processes underlying these principal mechanisms are identified and will permit the development of predictive models for flyrock velocities.

Dec 13, 2023

By N. Hanief

This research involves the investigation of phase transformations in the platinum-chromium coated system. Single-layer 0.1 µm platinum coatings were deposited via electron beam deposition on 99.98 percent pure chromium substrates. Specimens were subjected to systematic heat treatment in a vacuum furnace at 900°C for up to 20 hours. Phase formation and the changes in surface morphology were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM).Both CrPt and Cr3Pt phases are formed during heat treatment for different times at 900°C. Significant changes in the morphology of this coated system were detected after heat treatment at 900°C for 20 hours.

Jan 1, 2012

By M. Ndabeni, J. H. van Vreden, M. Le Roux, Q. P. Campbell

It is not uncommon for gold slurry ponds or screen oversize dumps to contain several different types of carbon-rich contaminants. These contaminants act as robbers of dissolved gold which has a detrimental effect during the downstream carbon-in-leach (CIL) or carbon-in-pulp (CIP) processes. With a renewed interest in the reprocessing of contaminated gold waste ponds and dumps, preconcentration of the feed to either the CIL or CIP process becomes important to maximise profits from these resources. An added advantage in removing these resources, which were once thought of as being uneconomical, is the availability of land that can further be rehabilitated for community development projects. For gravity separation, an example of suitable technology is the Reflux Classifier (RC), which can be used for the separation of materials of different densities and can be used as a pre-concentration step. In this project, a laboratory-scale Reflux Classifier was used to pre-concentrate a gold-bearing sample obtained from a waste dump situated to the east of Johannesburg, South Africa. The material had an average gold grade of 1.9 g/ton and a carbon content of 10%. This material was first fed to a semi-batch Reflux Classifier that was used to fractionate it into several different density intervals by varying the fluidisation water feed rate, followed by continuous runs at fixed water flow rates. The results showed that a cumulative gold recovery of 60%, carbon recovery of 85%, and mass pull of 41% was possible for a fluidisation water feed rate of 15 L/min, while a rate of 20 L/min resulted in a gold recovery, carbon recovery and mass pull of 83%, 92% and 79% respectively, which translated into a concentrate gold grade above the set target of 3 g/ton. Continuous operation at 20 L/min yielded an underflow stream with 84% gold recovery at a grade of 5.4 g/ton. Keywords: Reflux Classification, gold recovery

Jan 1, 2020

By P. T. L. Koh, M. P. Schwarz

A series of parametric studies were carried out for a flotation cell using computational fluid dynamic (CFD) modelling to determine the local response of hydrodynamic performance measures to change in operating conditions. As an example, an Outotec cell was used to carry out the response analysis. The hydrodynamics of the flotation cell has been previously investigated by laboratory measurements presented by Schwarz et al (2019), and a CFD model of the cell was developed and validated using these measurement data (Schwarz et al., 2019). In this work, parametric studies have been performed by modelling the flotation cell at different stirring speeds and gas flowrates, varying above and below standard conditions. Predictions of void fraction, bubble size, bubble surface area flux and particle–bubble collision rate are presented showing the effects of increasing and decreasing stirring speed and gas flowrate around the base case. Generally, the total gas holdup in the flotation cell was found to increase with increasing gas flowrate. The bubble diameter was found to decrease with increasing stirring speed and increase with increasing gas flowrate. The collision rate increased with both stirring speed and gas flowrate. The parametric results show that there is a correlation between the bubble surface area flux Sb which is affected by stirring speed and gas flowrate, and the particle–bubble collision rate. With the collision rate as an indication of flotation collection, it is also possible to show that cell performance can improve more by increasing stirring speed than by increasing gas flowrate in a situation where everything else remains constant. The CFD results can form the basis for a Response Surface Method (RSM) analysis which can then be used for automated optimization of cell performance. Keywords: Flotation kinetics, computational fluid dynamics, bubble surface area flux, particle-bubble collision rate

Jan 1, 2020

By S. Ramatsoma, D. N. C. Phillpotts, B. Whitehead

Changes in flotation performance have been correlated to changes in froth structure, velocity and stability. Literature has shown that when the aeration rate is varied for a specific float cell, the recovery of the valuable mineral reaches a peak which also coincides with a peak in the air recovery – a measure of froth stability. Peak air recovery optimisation methodology is a way to use direct readings of physical phenomena by froth cameras to optimise the metallurgical performance of a flotation plant. The aim of this paper is to show the transient nature of the peak air recovery value and the variety of conditions required to attain the peak air recovery on an industrial flotation plant with tight base-layer control of the feed and internal conditions. Industrial site tests that were conducted under controlled conditions showed different peak values at significantly different corresponding aeration rates during normal operation. The measured peak air recovery points corresponded to maximum PGM recovery during normal flotation, as expected. This dynamic nature of the peak air recovery point conditions has not previously been discussed in literature and indicates the need for online measuring equipment and informs the design of process control algorithms required to exploit the phenomenon for optimisation. Keywords: Froth flotation, flotation control, flotation optimisation, peak air recovery

Jan 1, 2020

By K. Eckert, A. E. Sommer, S. Heitkam

One highly relevant challenge in flotation is the recovery of fine particles. Due to their low inertia, these particles are mostly pushed aside by rising bubbles. Consequently, they typically exhibit low probability for bubble-particle collision and thus, a poor recovery rate. In this work, the trajectories of fine particles in the vicinity of rising bubbles were investigated. The measurements considered a chain of millimetric bubbles in a rectangular container filled with deionized water. The flow field near the bubbles was measured by tomographic particle image velocimetry (TPIV), employing fluorescent tracer particles of 33μm diameter. Subsequently, trajectories of larger particles and bubble-particle collision events are recorded with 4D particle tracking velocimetry using a high temporal and spatial resolution. The results reproduce the well-known collision of particles on the leading edge of a rising bubble. Additionally, collisions on the tailing edge were observed in cases with a low Stokes number. The TPIV results demonstrate, that the high turbulent kinetic energy in the bubble wake allows particles to divert from the fluid streamlines and collide with the tailing edge of the bubble. The tailing edge collision probability increases with the bubble Reynolds number and decreased particle inertia. Overall, the investigation shows that the collision of fine particles in the bubble wake should be considered for the development of further collision probability models. Furthermore, the importance of turbulence on the fine particle flotation was demonstrated. Keywords: 4D Particle tracking velocimetry (PTV), tomographic particle image velocimetry (TPIV), fine particle flotation, collision probability, bubble-particle interaction, wake induced collision

Jan 1, 2020

By S. T. L. Harrison, J. R. Amaral Filho, M. Smart, J. Broadhurst, J. Weiler

Technosol production from mine waste, following amendment with additional organic residues, to provide healthy and functional topsoil is an advantageous alternative to the long-term dump disposal of mine waste. Minimising the legacy of mine waste and supplying soil for mine site rehabilitation contributes towards more sustainable mining practices. Following the creation of the physicochemical structure of the soil from appropriate mixtures of coal waste with low sulfur content, physical ameliorants and nutrient sources, the inoculation of Technosols with active microbial suspensions may accelerate the decomposition of organic matter present and ensure nutrient availability for plant growth through active nutrient cycling, particularly of nitrogen, sulfur and phosphorous. In this paper, South African ultrafine coal waste was used as the main mineral matrix, and malt residue was used as source of organic matter and nutrients. In order to evaluate the effects of Technosol inoculation, five microbial treatments were used, including the addition of: commercial grade efficient microorganisms (EM Prosoil), anaerobic digested sludge supernatant from treating brewery waste, and ‘tea’ extracts prepared from compost, vermicompost and soil native to the mining area. Growth experiments were carried out using Eragrostis teff, commonly known as teff, a grass typically used for the rehabilitation of mined areas in South Africa. Preliminary results showed that Technosols inoculated with microorganisms performed better in terms of nutrient availability and plant growth. Varied performance was observed as a function of the microbial inoculation applied. This suggests that the inoculation of Technosols with appropriate microorganisms may be recommended to accelerate nutrient availability assisting plant growth during the initial establishing of the Technosols. Technosols continue to show promise as an alternative to both mine waste disposal and the burrowing of topsoils for mine rehabilitation. Keywords: Fabricated soil, mine waste, coal discards, malt residue, nutrient availability, soil microbiology, plant growth

Jan 1, 2020

By G. T. van Rooyen

In this overview of materials engineering, the author, drawing on his long experience from his student days until the present (emeritus professorship), briefly recounts the main developments in this field: dislocation theory, fracture problems, and the development of alternative materials such as ceramics and polymers. He then takes a look at the future, in which he foresees a greater demand for materials engineers, and leading roles for universities and technikons in collaboration with industry.

Jan 1, 1996

By K. -I. Higuchi, M. Mizutani, K. Haga, A. Shibayama, A. Batnasan

In recent years, the quality of iron ores has decreased due to the increase in the content of impurities, namely quartz, aluminum, phosphorus, and sulfur. It indicates that the removal of impurities from iron ore is an extremely challenging task. In particular, the high amount of phosphorus in iron ore could be a problem for energy consumption and CO2 emission in the steelmaking process. To reduce the impact of phosphorus, mainly two approaches: the utilisation of low-phosphorus iron ore, or dephosphorisation of high-phosphorus iron ore using mineral processing technology, have been suggested. In this paper, the removal of phosphorus from a low-grade high-phosphorus iron ore containing 0.1 mass% P and 57.5% Fe by alkaline roasting and wet grinding is discussed. The iron ore consists mainly of hematite, goethite, and quartz. Effects of sodium hydroxide concentration used as an alkaline source, roasting temperature, grinding time, and particle size on the dephosphorisation of highphosphorus iron ore were investigated. The dephosphorisation efficiency, iron loss, and mineralogical components of low-grade high-phosphorus iron ore under various experimental conditions were characterised by using XRD, SEM-EDS, and particle size distribution analysis. Results showed that the phosphorus content was lowered from 0.1 mass% to 0.034 mass%, while the iron grade reached 59.8 mass% from 57.5 mass% by alkaline roasting with 0.05 w/w NaOH at 300 °C for 2 h, followed by wet grinding in an attritor with water for 30 seconds at room temperature. Under the experimental conditions, the dephosphorisation rate was about 54.7%, and the solution obtained by wet grinding contained 22.7 mg/L of phosphorus and 21.5 mg/L of iron. The recovery rate of iron by this process reached 99.9%. Keywords: Iron ore, phosphorus, dephosphoriszation, alkaline roasting, wet grinding

Jan 1, 2020

By H. Zhong, S. Wang, Q. Lin

To improve the flotation performance of chalcopyrite collector, 2-(tert-butoxy)ethyl xanthate (TBEX) and its derivative O-(2-(tert-butoxy)ethyl)-N-ethyl-thionocarbamate (TBEETC) were designed and prepared by the introduction of a 2-(tert-butoxy) ethyl group into xanthate and thionocarbamate. TBEX and TBEETC were both prepared via the one-pot method with superior efficiency, which has significant commercial implications. The micro-flotation tests demonstrated that compared with sodium isobutyl xanthate (SIBX) and O-isopropyl-N-ethyl-thionocarbamate (Z-200), TBEX and TBEETC both possessed better collecting ability and selectivity for chalcopyrite. DFT calculations and XPS were utilised to investigate the flotation mechanism involving TBEX or TBEETC and chalcopyrite. The results demonstrate that although 2-(tert-butoxy) ethyl group does not interact with minerals directly, its introduction reduces the energy of HOMO, so that they can better accept electrons instead of donating electrons which leads to better interaction with copper atoms rather than iron atoms. Keywords: Chalcopyrite, flotation, thionocarbamate, xanthate, synthesis

Jan 1, 2020

By T. N. Matveev, V. V. Getman, A. Yu. Karkeshkina, L. B. Lantsova, N. K. Gromova

Sulfide-type tin deposits in Russia are characterised by the complex mineral composition of ores and dump products of their processing. Tin-sulfide ores contain industrial quantities of copper, lead, zinc, tungsten, silver, rare and trace elements (indium, scandium, etc.). In addition, the ores are characterised by uneven dissemination of sulfide minerals (chalcopyrite, galena, arsenopyrite, etc.) and tin minerals (cassiterite, stannine, etc.). X-ray phase and spectral analysis, scanning electronic microscopy (SEAM), laser SIM and AFM microscopy helped to identify the selective fixing of sodium dibutyl dithiocarbamate (DBDTC) on chalcopyrite and galena, as well as the tall oil fatty acids (TOFA) and IM-50 on cassiterite. For the first time, collectors and flocculants of slurry fractions of silver and tin, thermomorphic polymers TMPF were used to isolate more than 80% silver from the tin tailings of the Solnechny mine into a copper-silver rough concentrate. It has been established that preliminary ultrasonic treatment and desliming according to the 0.02 mm class removes up to 20% of sludge material, which impairs the process of gravity separation. The combined flotation-gravity scheme using new reagent compositions helped to obtain tin concentrate with a tin content of 5.42%, which meets the requirements for further metallurgical processing (at least 5%). This work was supported by the RSF according to the research project No. 17-17-01292. Keywords: Flotation, flotation reagents, tin-sulfide ores, casiterite, adsorption, flocculation

Jan 1, 2020

By L. Forbes, G. Forbes, J. Wang

Bubble size measurement is a vital part of flotation system analysis and diagnostics. Over the years, a great many different bubble size analysis tools have been developed. However, all of them rely on ex-situ measurement and in-pulp sampling techniques. This paper evaluates the Mettler Toledo ParticleView™ Measurement probe as a novel method for in-situ bubble size measurement. This device is then compared to the conventional Anglo Platinum Bubble Sizer (StoneThree). It was found that the in-situ bubble size analysis technology appears to be a more user-friendly and reliable option for determining bubble size in flotation. However, the current instrument design is not suited to industrial applications. Keywords: Bubble size measurement, bubble coalescence, PVM probe

Jan 1, 2020

By M. L. Pududu, B. Ceki, K. Mohajane

This study was aimed at determining the effects of industrial action on profitability in the South African platinum mining sector. We compared companies where employees engaged in industrial action (affected companies) to strike-free companies (competing companies). Industrial action refers to strikes by rockdrillers, as these strikes typically result in the shutdown of production at the mines affected. A t-statistics analysis of significant differences in revenue and earnings of affected and non-affected platinum companies was conducted using data from platinum mining companies listed on the Johannesburg Stock Exchange from 2011 to 2015. Contrary to international studies, which suggest that the spillover effects of industrial action positively affect competing companies, our findings show that profits in the platinum sector decrease significantly during strike periods for both affected and competing companies. The results indicate industrial action is a threat to the profitability of all companies, and that employee demands should be prioritized and negotiated before they result in industrial action. Improved dialogue between management, labour unions, and employees in the platinum mining industry is recommended. The study contributes to the scanty literature on the effect of industrial action on the profitability of mining companies in a developing economy.

Dec 13, 2022