Search Documents

By Willard A. Murray

Investigations of underground coal gasification (UCG) have been actively pursued by the U.S. Department of Energy since the early 1970s; the Lawrence Livermore National Laboratory (LLNL) conducted its first field experiment in 1976. In conjunction with field and laboratory studies of the process of recovering energy in the form of combustible gases from the burning of coal deposits in situ, an extensive environmental program has been conducted at LLNL under the auspices of both the U.S Department of Energy and the U.S. Environmental Protection Agency. This program has focused on groundwater contamination and ground surface subsidence caused by UCG. The material presented in this paper is a summary of results from the environmental studies of UCG activities conducted by LLNL as described by Mead, et al. (1981) and supplemented by the author's experience with this program in 1980 and 1981. The following sections describe specific groundwater contamination and surf ace subsidence problems encountered during field experiments in northeastern Wyoming, and will discuss implications of preliminary findings from geohydrological investigations of a site in southwestern Washington. Finally, possible environmental control technologies that are most likely to be effective in mitigating environmental impacts are discussed.

Jan 1, 1982

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

By L. R. Gremillion

Chemical and mineralogical data on 25 apatitic phosphate ores of diverse origins from commercial deposits around the world were widely variable. From 14 to 18 chemical constituents of each sample were determined, and each sample contained 4 to 10 mineral phases. Altogether there were 34 different mineral phases, many of which occurred in only one sample. The samples contained varieties of francolites, fluorapatites, and mixed hydroxyl-fluorapatites. The apatite compositions calculated from the chemical data showed that certain types of substitutions were characteristic of different apatite varieties, but every variety had some degree of substitution of (CO3)2 for (PO4)3 and the P2O5 contents of the apatites ranged from 35.1% for a North Carolina apatite to 41.9% for a Missouri apatite. In a concentrate with a grade of 32% P2O5, the North Carolina sample should contain about 8.7% gangue and the Missouri sample about 23.7% gangue. To optimize the digestion process of a phosphate are, it is necessary to consider the dissolution behavior of the different mineral phases during acidulation and the effects they may have on the chemical properties of a fertilizer intermediate. In the production of wet-process acids or superphosphates, the acidulation of certain minerals may cause foaming and formation of sludge, filtration, corrosion, and handling problems.

Jan 1, 1978

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By Y. J. Son, S. S. Nageshwaraniyer, K. M. Kim

"This paper reports on the development of a simulation-based framework for obtaining optimal blast design parameters for a hard-rock mine. To do this, a conventional medium-sized hard-rock mine was taken as a case study. The mine has two pits containing hard and soft rock types. The proposed framework contains a combination of regression analysis using Excel software by Microsoft and discrete-event simulation using Arena software by Rockwell Automation, applied to construct a model of the material-handling network of the mine. Specifically, blasting parameters are estimated by Excel-based regression analysis, processes including blasting and haulage from pits to crushers are modeled by a Forward Blasting simulation submodel, and material-handling operations including crushing, storage in stockpile, and haulage via conveyors and into SAG and ball mills are modeled by a Crusher to Ball Mill simulation submodel. A Reverse Blasting submodel is then used to obtain the optimum blast design corresponding to a target P80 particle size. Using the proposed framework, an economic analysis was performed to demonstrate the cost savings that could be realized for each rock type as a function of specific explosive energy. IntroductionIn a modern hard-rock mine, various processes such as drilling, blasting, crushing, grinding and mineral liberation are optimized to increase productivity, a practice known as mine-to-mill (MTM) optimization. Blasting is important in MTM optimization as it is the first comminution process and has an impact on all downstream processes (Julius Kruttschnitt Mineral Research Centre, 1996; Nielsen and Lownds, 1997; Nielsen and Malvik, 1999; Chung and Katsabanis, 2000; Kim and Kemeny, 2011a; Kim and Kemeny, 2011b).Two main research topics have emerged in the area of blasting design: (1) identifying the optimal target blast fragmentation at each shot and (2) controlling the blast fragmentation for that target. As part of an MTM optimization study, Kim and Kemeny (2011a; 2011b) developed a site-specific blast fragmentation prediction model that can be used to identify the target blast fragmentation and can be incorporated into MTM optimization. They also reported methodology for assigning model parameters easily and with minimal human bias."

Jan 1, 2015

By Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

Most of the future phosphate resources in Florida, which accounts for 70  percent of production in the United States, are contaminated with too much dolomite that is difficult to remove with existing industrial practices. The low-grade ore quality coupled with increased phosphate demand is of concern to the Florida phosphate industry. In order to resolve the dolomite issue, various beneficiation technologies were designed and evaluated, but none have been sufficiently successful [1]. 

By Jerome C. Motz

Los tipos, tamaños y número de trituradores empleados en un sistema completo de reducción varían con factores tales como: el volumen de mineral que debe ser procesado, tamaño de la mina, tamaño máximo del todo-uno, dureza del mineral y de su roca soporte y tamano requerido para el producto final. Básicamente, sólo existen tres tipos distintos de equipos de trituración para la etapa primaria. Estos son: machacadoras de mandíbulas, trituradores giratorios y molinos de impactos, y cada uno tiene unas características operativas propias. Las trituradoras de mandíbulas operan por aplastamiento de las rocas entre dos paredes, una fija y otra móvil, en una cavidad determinada. Han sido ensayadas variaciones en la caída y movimiento, pero la mayoría de las máquinas del tipo Blake tienen un ángulo de trituración de aproximadamente 27° entre las mandíbulas fijas y móviles. El principio de trabajo del triturador giratorio es muy simple. Si un cono es montado en un eje vertical y la parte superior del eje se sitúa estacionaria mientras que la parte inferior gira excéntricamente, el cono tendrá también un movimiento excéntrico. Si el cono se coloca en una carcasa conveniente se movers aproximándose y retrocediendo de las paredes que lo contienen a la vez que gira. Si el cono y las paredes de la carcasa son suficientemente robustas y pesadas, cualquier cosa apresada entre ellas será triturada. Al lado de los incrementos de la eficacia desarrollados por las continuas acciones de trituración y el curvado de las caras de trituración, los trituradores del tipo giratorio tienen las siguientes ventajas: 1. La gran abertura de alimentación disponibles en comparación con trituradores de otro tipo. 2. El alto rango de tamaños y capacidades, que se encuentran entre 600 y 6.000 toneladas por hora. 3. Generalmente no es necesario control en la alimentación. Dumpers de 150 a 200 toneladas descargan directamente en las actuales instalaciones.

Jan 1, 1982

By Weiguo Xie, MARK LAPUTKA

The pyrometallurgical industry plays a vital role in producing metals for our modern life. With growing demand of metals and declining grade of mineable ore, innovations become critical for many mining companies. It is necessary to conduct a review of recent improvements to the pyrometallurgical industry on analytical measurement techniques, process and equipment improvements, and computer-based modeling/simulations. Many of those innovations tend to be applied to wider metals, and not be restricted by a specific metal. Therefore, we tried to cover the wide applications of many improvements to wider range of metals to reflect this trend. The challenge of a lack of robust measurement techniques under high-temperature conditions within a furnace hinders optimization of a pyrometallurgical process. Some future opportunities in the pyrometallurgical industry on analytical measurement techniques, computer modeling, and processes and equipment have also been outlined and discussed.

Jan 26, 2021

By M. E. Ryan, C. L. Hoebbel, E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not imply endorsement does not constitute endorsement by NIOSH. ABSTRACT It has been suggested that effective disaster prevention and response in mining requires that elements of emergency management be incorporated into everyday operations, planning, and decision-making, much in the same way that the industry approaches routine risk management. Since Congress passed the MINER Act in 2006, the newly mandated structural and technological advancements in mine emergency response preparation have been made and are apparent, but measureable improvement in mineworker emergency preparedness is difficult to ascertain. To begin exploring whether measurable indicators of mine workforce preparedness can or should be addressed within a risk management framework, NIOSH researchers examined the datasets from two separate research efforts—one which measured the organizational safety climate and self-reported safety performance, and the other which measured individuals’ perceptions of their own self-escape competency. INTRODUCTION In response to the mine disasters in 2006, the United States Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which strengthened existing regulations [30 CFR, Part 48] and introduced new provisions to improve mine emergency response. Since that time, new technological and structural features, such as mandated redundant communication systems, personnel tracking systems, and lifelines in primary and secondary escapeways, have been installed in underground coal mines across the country. Additionally, mine operators are required to develop emergency response plans, provide adequate supplies of breathable air throughout the mine, provide more frequent and realistic expectations training, and are required to immediately notify the Mine Safety and Health Administration (MSHA) in the event of an accident. While the structural and technological advancements in emergency preparedness are readily observable and easily measured, levels of individual mineworker preparedness remain difficult to assess. There is a general consensus that deficiencies in competence in the non-routine tasks required for individual miners to effectively respond to a mine emergency likely remain (e.g., National Research Council [NRC], 2013), and NIOSH research continues address this concern (Haas, et al., 2015; Hoebbel et al., 2018). To maximize an operation’s capacity to effectively prevent disasters and/or respond to emergency events, it has been suggested that individual and emergency management efforts be incorporated into everyday operations, planning, and decision-making in much the same way organizations manage routine risks to health and safety (Haddow et al., 2017). To the authors’ knowledge, the mindful intersection of routine risk management policies and practices and emergency prevention and response readiness have yet to be empirically studied within the mining industry.

Jan 1, 2019

By J. C. Stankus

Many coal seams are associated with soft floor strata and during mine development if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One of the methods for controlling floor heave is floor bolting. This paper describes the demonstration of floor bolting methods in a West Virginia coal mine. Three methods were used: (1) vertical full resin bolting, (2) floor truss bolting, and (3) floor truss bolting plus a floor cut at the center of the entry. The design of each method and the experimental results are discussed in detail.

Jan 1, 1993

By W. R. Reed, J. P. Rider

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) recently developed a series of models using computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a mediumsized surface blasthole drill shroud with a dry dust collector system. Previously run experiments conducted in NIOSH’s full-scale drill shroud laboratory were used to validate the models. The setup values in the CFD models were calculated from experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for several test scenarios, including 0.14 m3/s (300 cfm) and 0.24 m3/s (500 cfm) bailing airflow with 2:1, 3:1 and 4:1 dust collector-tobailing airflow ratios. For the 2:1 and 3:1 ratios, the calculated dust concentrations from the CFD models were within the 95 percent confidence intervals of the experimental data. This paper describes the methodology used to develop the CFD models, to calculate the model input and to validate the models based on the experimental data. Problem regions were identified and revealed by the study. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. IntroductionIn surface mines, production drilling is an essential process in blasting to fracture the hard rock overburden for removal. During the process, considerable amounts of respirable dust are produced. Past sampling at the shroud area of blasthole drills had documented time-weighted-average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 (Organiscak and Page, 1995) and 1.04 to 52.30 mg/m3 (Listak and Reed, 2007). These high dust concentrations, which may contain silica, can lead to respirable dust overexposures for the miners working nearby. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal.Two basic methods are used to control drilling dust: a wet suppression system or a dry collection system (Cecala et al., 2012). Dry drilling techniques using a dust collection system are preferred in rural mining locations where a constant water supply is not available, and in the case of rotary drilling where water is associated with accelerated bit wear due to bearing degradation and hydrogen embrittlement. In addition, dry drilling eliminates freezing-related issues with water in colder climates. Dry dust collectors are highly effective at removing dust, especially the finer material, as long as they are properly operated and maintained (Listak and Reed, 2007; Organiscak and Page, 2005)."

Nov 1, 2016

By H. J. van Antwerpen

AngloGold Ashanti operates the world`s deepest mine, Mponeng gold mine, in South Africa. A vast refrigeration and ventilation system provides acceptable working conditions 3800m below surface at 60°C rock temperature. In such a system, optimisation and assessment of modifications becomes very difficult. With that in mind, a research project was launched to determine whether recently developed system simulation technology can be applied to a mine as vast and complex as Mponeng. Using the techniques and methods as implemented in FLOWNEX software, it was indeed proven to be possible to do a mine-wide combined simulation of compressed air flow, ventilation air psychrometry and refrigeration water systems. Interactions between the various streams included heat transfer, pressure drop, evaporation and condensation. The simulation model was used in a parametric study to test various water flow and temperature operating points for the refrigeration system. It was found that, given current limitations, the mine refrigeration system is running fairly close to optimal but with some opportunities for improvement. The simulation model also provided useful insight for future changes or extensions to the system.

Feb 23, 2014

By H. Y. Sohn

Considering the two most important issues the ironmaking industry faces today, i.e., energy consumption and greenhouse gas emissions, it would be advantageous to utilize the concentrate-size raw materials directly without pelletizing or sintering, especially without the use of coke. This plenary lecture describes two such processes developed at the University of Utah. One is the Flash Ironmaking Technology (FIT) and the other is a moving-bed process for continuous ironmaking with gaseous reduction of iron ore concentrate (MBIT). These technologies are designed to produce iron directly from iron concentrate without requiring pelletization/sintering and cokemaking in two significantly different temperature ranges. They take advantage of the high reactivity of the concentrate particles and will considerably reduce energy consumption and carbon dioxide emissions compared with the current processes. The process of the development from the conception of the idea, to kinetic feasibility establishment, to laboratory flash furnace, and finally to the operation of a prototype facility for the development of the FIT is discussed. The development of the MBIT also started with the formulation of the process concept, followed by kinetics feasibility establishment, and the design of a potential industrial reactor. The results of economic analyses on the FIT are briefly described.

May 12, 2023

By S. Torno

The elimination of ultrafine (<10 µm) clay particles is essential to the treatment of abandoned coal-washing plant tailings for the recovery of the remaining coal fraction by enhanced gravity processing. Effective hydrocyclone classification is required to remove this fraction. The highly variable composition and particle size distribution of such wastes creates significant difficulties in the operation of hydrocyclones for such classifications. Hydrocyclone laboratory investigations and their plant setup require lengthy or time-consuming tests. The use of empirical models of such classifications frequently requires modification to correspond to actual operating conditions. Results of the evaluation of computational fluid dynamics (CFD) modeling to predict hydrocyclone classification of coal-washing plant tailings are presented. Results of the standard k-epsilon turbulence, SSG turbulence and large eddy simulation CFD models are compared with the results obtained from analyzed hydrocyclone classifications. The CFD models tested are shown to be very effective in the simulation of hydrocyclone classifications for the determination of the classification particle size and adequate for determining the efficiency index values for many applications. The large eddy simulation model was identified as the most precise, but it is recommended that all three models be improved simulations of classifications above and below the classification particle size.

Jan 1, 2011

By S. K. Bhatt

This paper reviews major developments in continuous haulage technology for underground coal mines. Haulage systems, both in use and development, are investigated through a comprehensive literature search and visits to mines and manufacturers. The systems include flexible conveyor train, mobile conveyor, multiple-unit continuous haulage, extensible, and belt turning systems. Strengths and weaknesses of the systems are assessed in light of their operating under remote control and their application to the computer-assisted continuous mining machine being developed by the U.S. Bureau of mines. Through mining scenarios, candidate haulage systems are conceptualized to be consistent with the capabilities of the mining machine.

Jan 1, 1990

By G. A. Munoz

Gold leaching of an auriferous pyrite ore from the Portovelo deposit in Ecuador indicates that noncyanide leaching systems, such as thiocyanate and thiourea, are not as effective as the traditional cyanide system. For example, whereas approximately 95% of the gold can be leached from the ore with cyanide, only about 50% gold dissolution can be achieved with a thiocyanate leaching system. Electrochemical measurements indicate that gold is not cathodically protected by pyrite in these systems. Based on the results of preliminary diagnostic experiments, it appears that gold dissolution in thiocyanate and thiourea systems is limited by passivation due to the formation of either elemental sulfur or sulfur compounds on the gold surface.

Jan 1, 1999

By Alain S. Kivava, Olawale K. Aromolaran, Charles Nzolang, Anthony T. Bolarinwa, Georges M. Kasay

Rare earth elements (REEs) are crucial in high-tech and green technologies. The Democratic Republic of Congo (DRC), rich in mineral resources, shows potential for REE deposits in carbonatites, pegmatites, and placers. This paper reviews global REE resources, highlights potential REE targets in Africa, and emphasizes the need for further research and exploration in the DRC to unlock its REE potential.

Feb 4, 2022

By Veerendra Singh, NILAMADHABA SAHU, ARIJIT BISWAS

Manganese (Mn) ferroalloys are chiefly consumed in the steelmaking process as a deoxidizing agent or as an alloying element to produce high-quality steels. These alloys are typically produced in a submerged arc furnace using coke, fluxes and manganese ores of a specific manganese/Fe (Mn/Fe) ratio. Preferred-grade manganese ores should have Mn content greater than 46 percent and Mn/Fe content greater than 5 to produce commercial-grade, high-carbon ferromanganese [1]. Selective mining of high-grade Mn resources has created a scarcity of these resources, which is emerging as a major challenge for the manganese and steel industry. Manganese ore resources are mainly distributed in South Africa, with about 32 percent; Ukraine, with about 17 percent; Australia, with about 17 percent; and Brazil, India, China, Gabon and Mexico, with lesser amounts.

By Muhammad Azeem Raza, Muhammad Zaka Emad, Muhammad Usman Tahir, Saqib Ahmad Saki, Muhammad Usman Khan

Shotcrete is a key initial rock support component used in underground mining and civil projects. The strength of shotcrete plays a vital role in providing and deciding the support adequacy. The strength of shotcrete is evaluated by its uniaxial compressive strength (UCS) test that is usually conducted on extracted core samples. Shotcrete cores are commonly extracted from the test panels along the direction of its application; thus, its strength perpendicular to the direction of application is often neglected. The true bearing strength of shotcrete is thereby ignored despite the fact that higher stresses act normal to the direction of its application. Although the anisotropic behavior of shotcrete is well reported, no study has reported extensive testing of this scale and nature. This study reports extensive testing of shotcrete cores extracted from tunnels of a mega hydroelectric project in Pakistan. The study reports 7- and 28-days strength tests of shotcrete cores. The research also investigates the anisotropic behavior of steel fiber reinforced shotcrete and suggests that shotcrete exhibits higher strength perpendicular to the direction of its application.

Dec 26, 2022

By J. Stachurski

Flotation tests were carried out on 6 coal samples of different rank as well as their oxidized samples. A mixture of diesel oil and alcohols was used in these tests. Surface oxidation caused a distinct decrease of the flotation recovery with some improvement in the grade The reduction in the recovery increased with increasing the concentration of the oxidizing agent. The floatability of low rank coals was affected by oxidation to a higher degree than medium and high rank coals. The recovery size curves of oxidized samples mere similar in shape to that of non-oxidized coals.

Jan 1, 1990