Search Documents

By S. R. Hutchins

Several refractory sulfide and carbonaceous gold ores were examined to determine whether microbial pretreatment could be used to enhance gold recovery. Test samples were biologically leached using unique, thermophilic microorganisms to solubilize iron sulfide minerals. Gold recovery from sulfide ores and concentrates was enhanced following pretreatment with the thermophiles; responses varied widely for the individual materials. Although bioleaching had little effect on the preg robbing characteristics of the carbonaceous gold ores, cyanidation of the bioleached residues yielded higher gold recoveries than cyanidation of the native ore. By combining bioleaching with abiotic processes designed to inhibit preg robbing, gold recoveries of 83-98% were obtained from carbonaceous ores yielding 10-50% gold recovery by direct cyanidation.

Jan 1, 1987

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for expensive large-scale tests that are currently being used. A radiant panel apparatus was used to determine the relevant thermal characteristics of the materials: time to ignition, critical heat flux for ignition, heat of gasification, and mass loss rate. Three thermal parameters, TRP, TP1, and TP4, were derived from the data, then were developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with thermal and ignition hazards of similar materials reported in the literature and represent a simpler approach to quantifying these combustible hazards. INTRODUCTION The potential fire hazard from combustible mine materials is a major concern that can impact the safety of mine workers. Combustible materials tend to be solids and within this category there exist degrees of flammability and fire resistance. These materials may be readily ignitable or they may be able to withstand high temperatures and high heat fluxes. Presently, no simple methodology exists to assess these possible fire behaviors and quantify the resultant fire hazards. Thus, better knowledge of the thermal properties and chemical characteristics of combustible materials is of great importance to the safety of mine workers. Tewarson [1994] developed a methodology which he subsequently used to evaluate the ignition and fire resistant properties of combustible mine materials, but these efforts are more than 20 years old, and do not include many of the new materials used in mines today. The standard practice that has evolved for a combustible material to be approved by the Mine Safety and Health Administration for use in underground coal mines is to conduct extensive and costly large-scale experiments on each new material that is used in a particular mine operation. Results of such tests provide pass/fail answers to the questions of a material’s flammability or fire resistance, yet they provide little, if any, information that will lead to a better understanding of the basic mechanisms involved. Therefore, there is a need to quantify material flammability properties and to develop a methodology to rank the ignition and fire hazards of commonly used underground mine materials. During the heating and ignition stages of combustible materials, properties such as smolder susceptibility, minimum surface temperature for ignition, thermal conductivity, heat capacity, density, and heat of gasification are known to be important [Apte, 2006]. During the flaming stage, additional parameters, such as the heat of combustion, heat release rate, flame spread rate, yields of soot/smoke, and toxic gas production become more important as the flame is sustained and spreads. In very general terms, the heat flux incident on the surface of a solid combustible not only controls the rate of temperature increase of the local fuel surfaces, resulting in expulsion of fuel vapors that sustain the flaming process, but also the heating of other combustible surfaces that subsequently ignite and spread flame."

Jan 1, 2015

By Andrew P. Gize

The analytical approaches used to solve a specific problem are dependent upon the information required, coupled with limitations imposed by available facilities, costs, and time. The organic matter associated with ore deposits has the potential to yield information for two problems. Information can be obtained to provide guidelines for prospecting, and, secondly, to solve genetic problems. A major potential of organic matter in providing prospecting guides lies in the high thermal sensitivity of organic matter in sediments which are metamorphosed at grades lower than greenschist facies. The organic matter can then be used to map thermal anomalies potentially associated with mineralization. The analytical approach is to determine the thermal maturity of the total organic matter, or of specific fractions, using techniques which are relatively quick and inexpensive. Consideration of genetic models (for example, reduction, complexing, involvement of oil field brines) generally requires more specific information than the overall thermal maturity of the organic matter, necessitating infor¬mation on molecular composition and structure. The facilities, time, and cost of this information are greater than for mapping thermal anomalies. The analytical techniques discussed include elemental analyses, spectroscopy (infra-red, visible and ultra-violet), Fourier Transform infra-red, nuclear magnetic resonance, extraction, pyrolysis techniques, chromatography and mass spectrometry.

Jan 1, 2013

By John W. Straton

Following the completion of the paper presented in February, 1972, data were received from many other mines and some original respondents submitted more complete questionnaires. The computer program was changed to permit the results to reflect more clearly all the data reported by the mines. The original paper was revised to reflect the new information. There were significant changes in some numerical values, particularly where the size of the sample changed appreciably. Some limited samples considered originally in arriving at conclusions were not relied on in this revision. The revised tables and text are of the same design and format as the original paper.

Jan 1, 1972

By B. Sameti

Blast engineers have been taking advantage of image-based rock fragmentation analysis methods for the past 3 decades to estimate rock size distributions. These methods utilize a wide range of image segmentation techniques, from manual to fully-automated, to delineate the edges of rocks in images. Rock delineation results are then converted to physical rock sizes (and percentage passing curves) by scaling the image pixels to correspond to physical measurements. The size scaling process is critical for acquiring physical measurements, but specific to the limitations of different applications. This article starts by presenting a shovel bucket-based fragmentation analysis system, where scaling is done using the known width of the shovel bucket within the image. Next, it describes methods that use pictures captured by digital cameras with scaling reference objects in the view. Finally, the article presents a method that uses three-dimensional imaging to capture images without the need for scaling reference objects. A portable device which utilizes a three-dimensional imaging method is proposed, and compared with the other methods. The proposed solution combines the generated three-dimensional points with the delineated rock boundaries in the image to reconstruct the surface, and generate accurate rock size estimates and percentage passing rock size distributions. System operation is described and its accuracy and performance are discussed for various scenarios. It is shown that since the device does not require a physical object for scaling reference, it is free from the limitations of other methods, and can be applied for automatic rock size measurement from various sources such as mining shovels, loaders, crushers, stockpiles, haul truck beds, and conveyor belts.

Feb 23, 2014

By M. S. Celik

Unlike most other minerals, electrokinetic measurements of calcium montmodonite (a clay mineral) and u1exite (a boron mineral) exhibit an unusual behavior. While the addition of monovalent salts such as NaCI and KCI is expected to compress the electrical double layer with a resultant less absolute charge, an opposite trend is observed. A set of systematic experiments with monovalent and multivalent ions has been carried out to understand the mechanism of this phenomenon Examination of the results reveals that the behavior of montmorillonite is dictated by the exchangeable divalent cations at the edges which undergo an exchange process with monovalent cations resulting in the reduction of positive charges. The solubility of ulexite, on the other hand, is found to decrease with increasing monovalent cation concentration leading to again an increase in the absolute negative charge.

Jan 1, 1996

By M. Guzman, M. Romero, S. Bravo-Thais, M. Flores

The phytoremediation method is proposed to recover valuable metals from polluted soils. In this sense, the objective of this research is to determine if it is possible to use native plants in the recovery of precious metals from abandoned mining liabilities. The tailings samples containing Au and Ag were acquired from the northern region of Peru. Two native plant species, Stipa Ichu and Cortaderia Nitida, were used. Results show that Au was recovery around 19% (1.52 mg/Kg) and 25.43% (1.78 mg/Kg) by using Stipa Ichu and Cortadeira Nitida, respectively. Besides, Ag had a better recovery in the Stipa Ichu reaching a value of 6.83% (0.628 mg/Kg); in contrast, Cortadeira Nitida had an efficiency of 3.6% (0.814 mg/Kg). Bioaccumulation, bioconcentration and translocation factors were calculated by determining the concentration of precious metals in the roots and aerial parts of each plant. Results show that Stipa Ichu had a greater capacity of hyperaccumulated Ag compared to Au; while Cortaderia Nitida tended to have a better performance for Au. In conclusion, both plants are recommended for phytoremediation of mining liabilities.

Feb 1, 2023

By G. Southam

Bacterial populations play an active role in mineral weathering in subsurface and near-surface environments e.g., supergene enrichment of Cu at Morenci, AZ. An in vitro bacterial biofilm model was used to examine the interaction between Sporosarcina ureae and ionic gold (which is toxic) or amino acid-gold complexes in gold mobility. The immobilization of ionic gold was between 80-90% for 1 week but as the available, cellular reactive sites became saturated immobilization decreased to 14% within 2 weeks. In the asparagine-gold system, gold immobilization occurred at a high rate (80-90%) throughout the experiment with limited toxicity towards Sporosarcina ureae.

Jan 1, 1999

By C. Villa Diniz

It is proposed that battery grade Mn02 can be produced directly from a manganese ore from Azul Mine in Brazil, by leaching with HCI to remove heavy metals selectively. We are working to find a way of selectively separating Cu, Ni, Co, Pb and Fe from the resulting acidic manganese chloride solution, to detoxify it and produce marketable chloride solution. Chelating ion exchange resins are proving more promising for this separation than solvent extraction with commercially available reagents. Results from batch and column ion exchange tests that characterize the behavior of copper, nickel, cobalt, lead and iron are reported.

Jan 1, 1999

By P. Gelfi, J. Vanderbeek, J. Enriquez

"The Cerro Verde copper-molybdenum mining complex is located near Arequipa, Peru. A 108,000 t/d copper concentrator (C1 concentrator) commenced operation in late 2006 and was debottlenecked to a 120,000 t/d capacity in 2011. A feasibility study, initiated in May 2010, assessed the potential for expanding the processing rate of the large Cerro Verde sulfide reserve via the installation of a second, stand-alone, concentrator (C2 concentrator) capable of processing a nominal 240,000 t/d ore. The feasibility study was successful and the project advanced through engineering, permitting and construction. Ramp up to nameplate capacity was ahead of schedule. The overall project was completed on schedule and within budget. The details of the project and supporting components are described. The design philosophy and design basis of the concentrator facilities are discussed as are factors that influenced the concentrator layout. Risk mitigation features included in the design are reviewed. The factors that drove the successful and rapid ramp up to nameplate capacity are discussed. Operational experiences in the first year of plant operation and project lessons learned are described. INTRODUCTION/BACKGROUND Sociedad Minera Cerro Verde S.A.A. (SMCV) operates a copper mine near Arequipa in southern Peru. Small scale operations operated intermittently until 1970 when the deposit reverted to the ownership of Minero Perú S.A (Peruvian government). Minero Perú S.A. commenced mining and processing of oxide reserves in 1972 and placed an SX-EW plant into production in 1976. The ownership of the property has changed hands several times over the years. Minero Perú sold Cerro Verde to Cyprus Climax Metals in 1994. Cyprus was acquired by Phelps Dodge in 1999. Freeport-McMoRan (FCX) acquired Phelps Dodge in 2007. Several studies were undertaken during the 1990’s that tried to establish the economic justification to process the large primary sulfide resource that underlies the surface oxide deposit. None of these studies produced an economic conclusion until a feasibility study was completed by Phelps Dodge and SMCV in 2004. This study provided the economic justification for the construction of a 108,000 t/d concentrator during 2005 and 2006. The key to the success of this study was identifying a water source that was sufficient to support processing economies of scale. Concentrator operations commenced in late 2006. The original design production rate of 108,000 t/d was achieved on a 30 day moving average basis on the 266th day after ore was first introduced. During 2009, studies and evaluations were performed that had the objective of addressing observed concentrator bottlenecks to allow a production rate of 120,000 t/d to be achieved. The 120,000 t/d figure represents the sustainable production limits associated with the installed primary crusher and tailing thickeners which would have been prohibitively expensive to upgrade. Debottlenecking activities were implemented during 2010 allowing sustained production rates of 120,000 t/d to be achieved."

Jan 1, 2017

By G. L. Mowrey

One of the critical parameters of any automated coal mining system is the ability to only cut coal and not the rock / waste surrounding it. To do this the system must be able to detect where the coal-rock/ waste interface is. The U.S. Bureau of Mines is investigating a new approach to vibrational coal interface detection (CID) by utilizing an adaptive signal discrimination (ASD) system to perform feature extraction and classification of complex vibrational signals. Accelerometers, geophones, and piezoelectric films are mounted on mining machines and/or strata and are used to monitor vibrations produced during mining operations. Selected data are digitized and the ASD system is trained on known types of vibrations (e.g., "cutting coal" and "starting to cut roof"). A signal classifier is then generated which can be used to identify unknown waveforms. The ASD system can be retrained if mining conditions change significantly.

Jan 1, 1990

By K. J. Shoop

This study investigates the use of a horizontally-baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Jan 1, 1997

By M. Guzman, S. B. Thais, M. F. Obispo, M. R. Arribasplata

One of the greatest environmental issues related to the development of the mining activity is the generation of Acid Mine Drainage (AMD). Many methods have been developed for AMD treatment, being wetlands a good option for heavy metal removal. In this sense, the implementation of artificial wetlands for the treatment of mining effluents would seem to be an environmentally friendly alternative. In this paper, we present the results on the elimination of heavy metals (Cu, Zn, Pb and Fe) using two Peruvian native species such as Schoenoplectus californicus (C.A. Mey.) and Phragmites australis (Cav.) Trin. Ex Steud. The results show that Schoenoplectus californicus preferentially removes copper (82 and 90%), lead (88 and 92%) and iron (28 and 69%), whereas Phragmites australis removes copper (68 and 87%) and zinc (53 and 95%). Likewise, it is observed that the Schoenoplectus californicus mainly retains the ions in its root, copper (89%), zinc (84%) and iron (76%). While the Phragmites australis accumulates iron (62%) and copper (74%) in the steam and root part respectively

Mar 2, 2022

By Mohammed Laraba, Rodrigo Alvarez Garcia, Juan Maria Menendez-Aguado, Roula Abdelmalek

The aim of this research is the study of the WHIMS parameters on the improving process of a local (DD: Djebel Debbagh, East of Algeria) kaolin. The obtained results of performed XRF, SEM, and XRD characterization showed that this local material is an alumino-silicate containing kaolinite and halloysite with MnO and Fe2O3 impurities (respectively 39.30% and 34.67% alumina and 38.18% and 39.70% silica in both samples (DD2 and DD3). After homogenization, crushing, and milling, a multiparameters factorial experimentation (grain sizes, intensity, and dimension of matrix balls) showed that WHIMS is an effective process to improve the quality of this kaolin, mainly: removing their impurities. Dimensions of matrix balls (Db) = 2 cm, intensity of the applied magnetic field (I) = 1.5 T, and grain sizes (Dp) = > 100 < 250 μm) are the optimal values to reach 91.06% for manganese and 93.45% for iron as removing yield. The statistical analysis of these results sorted the investigation parameters and showed that Db has the highest and most significant influence on the recovery of iron and manganese particles. The magnetic field intensity (I) has a less important influence while the grain size has an average influence (positive on the iron recovery but a negative one on the recovery of manganese).

Jun 11, 2022

By L. Sandbak

The Turquoise Ridge Joint Venture (TRJV) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestones, siltstones, and mudstones. The weak nature of the ground facilitates the underhand cut and fill mining methods. TRJV has been working to optimize ground support and mechanize top cut drift sizes and eliminate operating hazards associated with jackleg drilling. Safety Factor analysis based on bolt strengths has allowed us to pursue larger sized top cut drifts and to evaluate bolt length sizes and spacing. Switching from jackleg sized drifts of 10?W x 10?H to a mechanized 12?H x12?W top cut drift design has the potential to decrease overbreak, provide more uniform drift design sizes and bolt patterns, and increase ore production by at least 38%.

Feb 23, 2014

By R. T. Richins

Coeur d&apos;Alene Mines Corporation (CDE) is a precious metals mining company. The company&apos;s three mining operations are located In Nevada and Idaho. Collectively, these mines (Rochester in Nevada, and the Galena and Coeur In Idaho) produced about 61,000 ounces of gold and more than 7.5 million ounces of silver in 1991. The company is currently planning the development of two major properties; the Fachinal gold-silver project in Chile and the Kensington gold project near Juneau, Alaska. Fachinal and Kensington hold encouraging potential to significantly expand CDE&apos;s gold production during this decade. The permitting process for these two distinctly contrasting environmental settings, project design requirements and regulatory/political circumstances provide the basis for a comparative analysis of licensing and permitting requirements, timeliness of the permitting process and costs in the U.S. and Chile.

Jan 1, 1993

By S. Makni, F. Wang, A. Rosa, B. Klein, C. Saud, R. McIvor, A. Kumar, C. Gagnon, D. Gong

In response to the Natural Resources Canada “Crush It Challenge”, Corem partnered with the University of British Columbia and led a project to develop and demonstrate the use of high-pressure grinding to replace the workhorse of the industry, wet ball milling, with high-pressure grinding. Two plant case studies, a small tonnage gold recovery operation, and a large tonnage copper recovery operation, were carried out. Plant circuit performances were compared to pilot plants operated on the same circuit feed set up to represent the novel equipment and flowsheet that was developed to produce separation circuit feed. Numerous obstacles to industrial implementation of highpressure grinding in this role which were recognized at the outset of the work were successfully addressed. In both cases, comminution equipment energy savings alone, and final stage total circuit energy savings, exceeded 60% and 50%, respectively. Downstream mineral separation performance was the same or better.

Mar 2, 2022

By H. Akgun

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. This paper presents the results of push-out tests on cement grout plugs in salt. Two expandable cement grouts have been tested. The average interface shear strengths ranged from 2 to 12 MPa. Peak shear stresses at failure, assuming an elastic stress distribution along the interface, were up to eight times higher. Standard deviations commonly reached 20%. Dissolution along the interface was observed, and may have been enhanced by clay inclusions in the salt. This dissolution appears to have reduced bond strengths. Application of the results to the design of plugs for larger openings (e.g. shafts, drifts, or boreholes) is discussed.

Jan 1, 1991

By S. Park

In a flotation froth (and foam), air bubbles become larger due to coalescence, causing less hydrophobic particles to drop off. A bubble-coarsening model has been developed by calculating the changes in Plateau border area as a function of the initial bubble size at the base of a foam, liquid fraction, and foam height and then relating the predicted Plateau border area to the critical rupture thickness of lamellae film. The model predicts that bubble coarsens with increasing froth height, decreasing frother dosage, and decreasing aeration rate. The model predictions are in good agreement with actual bubble size measurements.

Feb 23, 2014

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models. INTRODUCTION There are many definitions of virtual reality (VR) that include various levels of immersion and features [1]. Some definitions refer to specific technologies [2], while others are limited to visualization [3]. For this paper, a more general definition of VR will be adopted. VR is defined as the collection of hardware and software that interactively engages users and stimulates their senses within a synthetic or virtual environment. From a hardware standpoint, this can include anything from a phone to a head-mounted display (HMD) to a large-scale theater as well as speakers, microphones, haptic sensors, and interaction devices. The software used to create virtual environments (VEs) generally includes a game engine, custom software components and libraries, and two-dimensional and three-dimensional graphical assets. Recent hardware and software advances have increased the fidelity and availability of VR. New and improved technologies including HMDs and high-resolution monitors and projectors can display sharper, more detailed visualizations. For example, in the past five years between the release of the Oculus Rift DK1 (2013) and the HTC Vive Pro (2018), there was a three-fold increase in resolution along with a 50% increase in the refresh rate. Furthermore, despite early claims that low-cost VR technology was readily available [4], computational power has not been sufficient to handle the large amount of data generated by these systems [5]. In the past five years, however, rendering speeds have more than doubled and memory has more than tripled [6], allowing these visualizations to be incorporated into higher-complexity and -fidelity VEs that more closely mirror the real world. Similarly, software capabilities have also significantly improved through game engine advancements and feature development. In the past several years, game engines have added and improved features such as physics, lighting, platform support (e.g. Android), and asset development integration. Some of the current leading commercial game engines are Amazon Lumberyard, CryEngine, Unreal, and Unity, but this can quickly change as is evident in the literature [7, 8].

Jan 1, 2019