Search Documents

By J. Carr

Ring gear and pinions used as the final drive on large metallurgical grinding mills are expected to transmit their rated horsepower reliably for long periods of time. Duty is 24 hrs./ day. Life expectancy of such gear sets is of the order of 20 years; that is, each gear and pinion flank is expected to resist failure by pitting for 10 years. This means that for a dual pinion gear set having a ratio of 18.42:1.0 and a mill speed of 10 RPM, every gear tooth will see 105.12 x 106 surface contact stress cycles and every pinion tooth will see 968.15 x 106 surface contact stress cycles in a 10 year period. The allowable surface contact stress on the gear and pinion is determined by the material hardnesses. The rule being the higher the hardness, the higher the allowable surface contact stress may be.

Jan 1, 1985

By B. Akwasi Osei

The lack of metrics to assess clamshell formation dredgeability limits the ability of engineers to predict the dredgeability of compact material and increases the risks associated with clamshell selection. Research is needed to develop metrics for predicting clamshell dredgeability. The objective of this paper is to evaluate possible metrics to predict the dredgeability of compact aggregates by hydraulically actuated clamshell dredges. Data on cylinder pressures and displacements, motor current, bucket tilt and cycle time (CT) were collected from a dredge. Work done and motor energy, potential metrics, were computed and their suitability in predicting dredgeability evaluated. Data analysis shows that; there is no correlation between tilt angle and work done or motor energy; a low correlation between CT and work done, and a strong correlation between CT and motor energy. Work done is a better measure of formation dredgeability, than motor energy, as it shows lower variability. However, in difficult digging conditions, work done alone does not accurately predict dredgeability. This work shows that, it is feasible to use cylinder pressures and motor signals data to predict dredgeability.

Jan 1, 2010

By S. C. Tadolini

The use of resin-grouted cable supports to control large ground movements in several types of underground mines has increased substantially since being introduced in 1991. Cables offer several advantages over traditional support systems, having large support capacities coupled with the flexibility to be used in low openings. Cable slings have been designed to be installed on-cycle using no-spin technology or a two-piece unit that can be placed with hand-held drilling equipment. Additionally, yielding cable supports have been developed and are being used to control large amounts of movement in coal and evaporite deposits.

Jan 1, 1998

By Barbara J. Arnold

A coal's size distribution, clay content and moisture content can affect its handling behavior, but the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.' s (formerly EPRI' S) Coal Quality Development Center (CQOC) and at Iowa State University (ISU) will answer these questions as part of a four-year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of various coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that, while moisture content-is the most important variable, the amount of -325M (-0.044 mm) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1990

By G. Włoch, E. Rudnik

The oxide fraction of industrial zinc ash was characterized in terms of chemical and phase composition, leaching behavior in sulfuric acid solutions, and leaching thermal effect. The waste product contained about 68 percent zinc (Zn), 7 percent chlorine (Cl), 2 percent aluminum (Al) and less than 1 percent other metals, such as iron (Fe), manganese (Mn), calcium (Ca) and silicon (Si). It consisted mainly of zinc oxide contaminated with metallic zinc and zinc hydroxide chloride. The dissolution of metals from the zinc ash was determined for solid-to-liquid ratios ranging from 100 to 500 kg/m3, acid concentrations of 10 and 20 percent, and temperatures of 20 and 40 °C. The best result — 130 g/dm3 Zn(II) at 95 percent zinc recovery — was obtained at a solid-to-liquid ratio of 200 kg/m3, sulfuric acid concentration RI SHUFHQWDQGLQLWLDOWHPSHUDWXUHRI ƒ& 7KH¿QDOVROXWLRQVZHUHFRQWDPLQDWHGPDLQO\E\0Q ,, DQG)H ,,, ions, but the presence of cadmium (Cd(II)) and lead (Pb(II)) ions enabled electrowinning of zinc of about 99 percent SXULW\DWKLJKFXUUHQWHI¿FLHQF\RI WR SHUFHQW /HDFKLQJRIWKHPDWHULDOZDVDQH[RWKHUPLFSURFHVVZLWKUHDFWLRQ heat of about 520 kJ/kg

By D. R. McMullin

The purpose of this paper is to provide a method for mine planners and engineers to evaluate on a conceptual basis if a shaft or a ramp is most suited for their particular underground access requirements. Mine planners and engineers are often raced with the decision of choosing which method of underground access is best suited for their particular requirement. Underground access can be provided by a shaft, ramp, adit, or slope for either exploration and/or actual production operations. This paper will focus on the construction cost and schedule differences between sinking a shaft and excavating a ramp which are currently the most typical access alternatives used in the western United States. It would be wrong to state that one method is superior to the other in every case. There are many variables to be addressed, and the degree of sensitivity of each of them will eventually dictate which method is the most suited to the particular circumstances. This paper compares the construction cost and schedule or sinking a shaft to excavating a ramp at different depths given different ground and hydrological conditions. This comparison provides mine planners with "rules or thumb" that may be applied to the access selection process.

Jan 1, 1994

In order to overcome some of the deficiencies associated with conventional fine coal cleaning methods, a novel process known as microbubble column flotation (MICROCEL?) was developed at Virginia Tech. This article provides an overview of recent commercialization efforts and in-plant testing of this technology. The results of the in-plant test work indicate that the MICROCEL technology offers several advantages for the upgrading of difficult to clean coals. The test data have also been used to develop guidelines for the design of coal flotation columns and to validate existing scale-up procedures.

Jan 1, 1991

By L. Piga, P. Cipriani, F. Pochetti

High-temperature roasting of alunite in the presence of K2CO3 gives rise to a reaction that results in up to an 80% recovery of its potassium content as K2SO4 by leaching of the roasted mixture. K2SO4 is also generated from the reaction between the added K2CO3 and the SO3 driven off during roasting of the alunite. This limits the environmental and corrosive problems involved in the thermal treatment of this mineral. A solid residue containing mainly aluminum oxide is also obtained. This could be used as raw material for the production of aluminum, as the use of K2CO3 does not introduce different cations than are in the ore. A statistical study was performed on the factors assumed to affect the recovery of potassium, namely, roasting temperature, K2CO3- alunite stoichiometric ratio and leaching temperature.

Jan 1, 2000

By Iga Trisnawati, Fitria Puspita, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Idi Amin, Andi Nurfaadhilah Ulfah

Laterite ore is a valuable resource due to its high content of metals essential for modern technology, including nickel, iron, and cobalt. However, extracting nickel from laterite ores is challenging due to their complex mineral composition and low nickel concentrations. This study examined the leaching behavior of pre-roasted laterite ore and the effect of roasting on leaching kinetics. The ore was roasted at temperatures of 280°C and 610°C for 3 h, followed by sulfuric acid atmospheric leaching. The results demonstrated that pre-roasting at 610°C significantly enhanced nickel leaching recovery, with up to 93% nickel successfully recovered. The leaching process of pre-roasted laterite ore was found to be controlled by diffusion through the ash layer, with activation energy values of 20.97 and 18.97 kJ/mol for laterite roasted at 280°C and 610°C, respectively. These findings indicate that pre-roasting can improve the leaching performance of laterite ore, potentially leading to more efficient and sustainable nickel extraction processes.

Feb 27, 2024

By Ilmar J. Martens

The statistical information and cost data used in this report has been made available by NICKDATA INC. Since 1982, NICKDATA INC. of Toronto, Canada, has produced an annual comprehensive nickel industry cost study. Up to date information on 22 mines, 21 smelters, and 16 nickel refineries representing 30 nickel production operations in 17 countries are included in the computerized cost analysis. The report is compiled from information obtained through regular annual visits to major nickel operations and continuous monitoring of information on all nickel producers. The 1984 report which was completed this summer, reveals drastic changes in the nickel industry cost structures.

Jan 1, 1984

By Leonidio Stegmiller

Since the petroleum crisis in 1973, charcoal1 is being considered one of the most important fuel for the Brazilian consumers, mainly for pellet's producers. In replacing fuel by charcoal mixed up with ore, obviously one of the first thing to be investigated is its influence in the product's quality. Special attention has been given to the metallurgical characteristics. This paper infocus the effect of increasing dosings of charcoal to the pellet's porosity and how other physical and metallurgical characteristics will be affected accordingly. This work was carried out using two different finesses of charcoal and dosing varied from 0.5 to 2.0%.

Jan 1, 1982

By Liming Yuan, A. C. Smith

Barometric pressure changes affect air density, leading to change in the mass of the gas in the gob. When the barometric pressure decreases, the volume of gas in the gob expands, while the volume of gas contracts when the barometric pressure increases, a process which causes the gob to “breathe” out and in. Although the concept of gob “breathing” is simple, its effect on spontaneous heating of coal in the gob area is not clear. In this study, computational fluid dynamic (CFD) simulations were conducted to model the spontaneous heating of coal in the longwall gob area under measured barometric pressure changes. A single longwall panel using a bleederless ventilation system was simulated. If there is no barometric pressure change, the intake airflow rate is equal to the return airflow rate. When the barometric pressure changes, these two airflow rates are no longer equal, and the difference between the two airflow rates represents the airflow rate the gob breathes in and out. The effect of inflow and outflow of gas on the potential spontaneous heating in the gob was investigated using the CFD model developed in our previous study. The effect of barometric pressure changes on the spontaneous heating was found to be dependent on the gob permeability and the coal oxidation rate. The effect of barometric pressure changes on oxygen concentrations in the gob was also examined.

Jan 1, 2010

By Ted H. Eyde

Nearly 17 years ago a major producer of synthetic zeolites started an extensive exploration program for natural zeolite deposits which resulted in the discovery of over 170 occurrences in the western United States. A few years later several of the other producers and consumers of synthetic zeolites also started similar exploration programs. Since then, small quantities of natural zeolite minerals have been produced from at least 12 deposits in the United States. Of these the Bowie deposit, about 13 miles north of Bowie, Arizona, is the most important,having produced over 5,000 tons of vitric tuff zeolitically altered to the mineral chabazite and minor amounts of the minerals erionite and clinoptilolite. Mining Districts and Mineral Deposits of Arizona compiled by Charles A. Mardirosian, Consulting Geologist, estimates the value of the total production from the Bowie deposit at a very conservative $2,000,000. Unfortunately, none of the companies responsible for the discovery and the initial production of natural zeolites made any effort to develop the high volume, low cost applications of this unique mineral raw material. Instead, they developed only the high unit value uses to supplement their existing synthetic molecular sieve product lines. With the producers of synthetic zeolites thinking in pounds and not in tons, further development of natural zeolite deposits stagnated for over a decade.

Jan 1, 1974

By Ralph C. Flow

In Cleveland County, North Carolina, one and one-half miles south of Kings Mountain, Foote Mineral Company operates an open pit for the production of spodumene, feldspar, mica, and commercial stone. Spodumene concentrate is sent to Footers Sunbright, Virginia plant and to other customers. Exton, Pennsylvania and New Johnsonville, Tennessee plants produce lithium compounds sold to the oil industry for multipurpose lithium-base greases, to the metal industry as welding flux, to the air conditioning market, and to the glass industry. Ceramic grade spodumene, feldspar, and mica concentrates go to other processing companies from the Kings Mountain plant. Waste amphibolite is delivered to a neighboring quarry operation.

Jan 1, 1962

By Michael A. Trevits

A mine fire represents one of the most dangerous and challenging safety issues facing underground mine operators. Given the right circumstances, a mine fire can occur at any location in the active or abandoned mine workings, can quickly grow beyond control, and threaten the welfare and livelihood of the entire underground workforce. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), has been conducting an in-depth program of research addressing mine fire prevention, early and reliable fire detection, and mine fire suppression technologies. One portion of this program is focused on understanding the characteristics of mine fire combustion products and flame spread through large scale deep-seated (firmly established) fire tests and use of computational fluid dynamics (CFD) modeling. In this study, two deep-seated fire tests were conducted; one fire consisted of coal material and the other utilized the two most abundant fuel sources found in a coal mine: coal and wooden cribbing blocks. The fires were burned to completion while the combustion products were collected and analyzed. In addition, an array of thermocouples was placed within the body of the material to measure flame spread rate. The coal fire test information was then used to develop a CFD model of the fire. This paper describes the fire tests, provides insight into characteristics of flame spread, and presents the CFD modeling work results.

Jan 1, 2009

By A. W. Khair

This paper deals with the evaluation of the interaction between rock and the cutting tool, and with methods for determination of workability, and abrasivity of rock. A description of instrumentation is included along with research on the wearing process of bit tips and pick consumption. Analyses of bit rotation, evaluation of cutting, normal forces and energy consumption is presented. Finally influence of the basic water jet parameters and water jet assistance on the cutting process of hard and abrasive sandstone is discussed.

Jan 1, 1995

By Jr. Hawk

The power generation industry may be required to reduce CO2 emissions if regulations related to global climate change are enacted. Coal-fired generation, which emits 82% of the power sector CO2, would be a likely target for CO2 reduction. Compliance with the Kyoto protocol will require a 30% reduction from the projected year 2012 emission level even with moderate load growth. This paper describes an analysis of power industry CO2 reduction options and their costs to assess how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered.

Jan 1, 1999

By R. Kahrger

This paper is written to convey the latest developments in compact bucket wheel excavators (BWE's) operating in medium-hard rock and will serve to indicate that BWE and compact machines in particular do in fact have application in materials other than loose sandy soils and soft rock. A recently run extensive three month field test in hard marl, which was previously considered too hard and difficult to be handled by a BWE, is used as an example to explain some of the design requirements and problems associated with digging harder materials.

Jan 1, 1990

By N. Myung, G. Hwang, H. Kim, Y. Han, S. Choi

"According to research presently being conducted on selective lithium recovery in seawater, inorganic adsorbents with high selectivity and capacity for capturing lithium ions from liquid lithium resources are called lithium ion-sieves (LISs). Their low toxicity, low cost and high chemical stability make LISs suitable for lithium recovery from seawater. In the present study, the ultrathin LMO nanofibers with controlled diameter were successfully fabricated by an electrospinning technique with a hypothesis that greater aspect ratio (i.e., smaller diameter) would lead to the enhanced recovery of lithium ion from seawater. Design of Experiment (DOE) and dimensionless analysis were performed to systematically optimize the diameter and morphology of nanofibers. Several complementary techniques including FE-SEM and XRD were used to evaluate the physical/physicochemical properties of the nanofibers. Lastly, the lithium ion recovery was tested for the nanofibers with different physical properties using lithium ion solution. INTRODUCTION Demand for lithium resources is increasing in many industries across the world.1-2 However, the conventional resources for lithium is very limited, and it even gets worse to secure the resources due to low grade and/or complexity of feed materials. Much effort has been, therefore, devoted to obtaining lithium from aqueous lithium resources. Several methods such as solar evaporation3-4, co-precipitation5, and solvent extraction6 have been proposed for recovering lithium from an aqueous lithium source, but there are limitations on its use; It takes a very long time or conditions such as temperature, pH and Mg/Li ratio are severe. Lithium ion-sieve (LIS) materials are considered as a good lithium adsorbent because of their unique chemical structure that can selectively separate lithium ion from brine and seawater.7- 10 Furthermore, their low toxicity, low cost, and high chemical stability make LIS suitable for lithium recovery from aqueous lithium resources. Spinel hydrous manganese oxide (HMn2O4) derived from spinel lithium manganese oxide (LiMn2O4) after topotactically extracting lithium from the spinel structure by acid treatment is most widely investigated LIS.10, LIS materials have been actively studied in various forms for easy handling and high efficiency (i.e. membrane11,12, foam13-14, granular15,16). Among them, the 1-D nanostructure LIS with high specific surface area is excellent in efficiency.9 In this study, we present the part of our recently submitted work17. Specifically, we fabricated systemically lithium manganese oxide nanofibers with different diameter as a lithium ion adsorbent using electrospinning technique through design of experiment (DOE). Enhanced lithium ion adsorption properties of the HMn2O4 nanofibers with different diameter were investigated in lithium liquid resources."

Jan 1, 2018

By A. P. Cook

Methane Rating has been developed from a need, in South Africa, for quick and simple measurement of coal face methane characteristics. It employs proven existing direct measurement methods, adapted specifically for rapidly advancing coal face conditions, to deal with the short term high release rates encountered during continuous miner coal cutting. The Rating is a comparative value, relative to the normal or average conditions encountered within a maintained data base. The seam gas content and the initial emission rate are plotted against each other on a graph, where they are compared with the average conditions to obtain the rating. The higher the seam gas content, and the higher the initial methane release rate, then the higher the Methane Rating, on a scale of 1 to 4. Methane being released from a newly mined coal sample is measured once underground, from a sealed gas-tight canister. The sample is returned, still sealed, to surface and milled to rapidly release the remaining methane. It is later intended that the milling process is also completed underground. Applications include the identification of changing methane conditions, outburst prone conditions, methane emission against advance, and mining in devolatilised coal.

Jan 1, 1998