Search Documents

By James M. Griffin

Ladies and Gentlemen, There have been no less than ten major coal project financings in the last eighteen months. Each of these has been in the order of $100 million to $1 billion for the development of a coal property and its associated infrastructure. It is appropriate at this time to review the nature of these past financings. Why has there been so much activity? There are primarily two reasons. The first is due to the large number of contracts which were signed as a result of OPEC oil shocks. High projections were made for increased coal consumption particularly in world trade. This is distinct from domestic coal mine/power plant projects which often tap a government source of funds. Second is the high cost of coal development in the 1980's compared with a typical company's corporate borrowing capacity.

Jan 1, 1984

By S. L. Bessinger

Introduction In the design and specification of a ventilation system for an underground mine, it is necessary to make reasonably accurate estimates of the pressure losses in the various airways of the mine. These estimates can be made with little difficulty for open airways with simple geometric cross-sections, such as those cut by continuous miners or tunnel-boring machines. The situation is much different on a longwall face, where the airway's complex geometric cross section and the presence in the airway of obstructing equipment having a variety of shapes make it difficult, if not impossible, to estimate pressure loss using traditional methods of calculation. Head losses in mine entries are calculated using Atkinson's Equation. [22H= KPLQ (English) H= KP 3Q (SO (1) 5.2AA] where H = pressure loss, in. of H2O (Pa); K = friction factor, lbf•min2/ft4 (kg/m3); P = perimeter, ft (m); L = airway length, ft (m); Q = airflow quantity, ft3/min (m3/sec); and A = flow cross-sectional area, ft2 (m2) In this equation, the friction factor, K, is an empirical constant that describes the aerodynamic roughness of the airway. Typically, the K-factor for a given airway is determined by measuring the factors H, P, L, Q and A in Equation (1) and calculating K. Tables of friction factors calculated in this way are found in textbooks and handbooks that deal with mine ventilation analysis. Unfortunately, very few K-factors have been measured on longwall faces, and the accuracies of those that have been measured are entirely site specific, because of the wide variety of equipment found on longwalls. The development of a technique for prediction without mine-site measurements of the friction factor for any longwall face, regardless of its configuration, will thus be very useful in the design of ventilation systems for mines in which longwall mining is practiced. Calculation of pressure losses using Atkinson's Equation (1) and empirically determined K-factors provides accurate and useful approximations in cases where the airways have relatively simple cross sections. However, a careful analysis using the principles of fluid mechanics shows that such calculations are based on two assumptions that are not strictly correct when there are obstructions in the airway. The first assumption is that the air velocity distribution in the cross section, particularly around the perimeter, is uniform. This assumption results from the fact that the tabulated K-factor values found in the literature are based on field measurements with uniform conditions. Such uniformity does not exist in longwall airflows. The second common assumption is that the K-factor, and corresponding head loss, is independent of the Reynolds Number (NR) for a given flow. In fact, this assumption is not strictly correct, and is particularly erroneous in the case of irregular protuberances into the airflow, such as those found on a longwall face. The errors arising from the assumptions may be avoided by using K-factors calculated by a newly devised method, described below, which takes into account the fundamental principles of aerodynamic drag analysis. This new technique has two advantages: first, it is flexible enough to model any longwall, regardless of equipment configuration; second, it employs terminology and equations familiar to those who perform mine ventilation analysis, using K-factors, for which ventilation engineers have an intuitive understanding, rather than drag coefficients. To provide guidance for development of a longwall drag model, data were taken on two modern longwalls operating in substantially different conditions. Pressure measurements at Mine B were made with 200-foot (61-m) sections of 1/8-in. (3-mm) diameter plastic tubing, attached to a Dwyer Magnehelic gauge. Pressure drops were measured in 200-foot increments down the face, and summed to give the drop for the entire face length. This technique was found to produce small, repeated errors because of the number of segments required to span the longwall. At Mine A this problem was avoided by using a single, continuous, plastic tube for the entire face length. The psychrometric properties of the air were measured for both Mines A and B. A calibrated, standard vane-anemometer was used to measure the airflow on both faces. Finally, numerous dimensions were measured on both faces, and face profile drawings were obtained to allow detailed evaluation of the face equipment geometry. From this information, accurate evaluations of the average wetted perimeter and average area of the longwall face airways were made. Since the airflow is not confined to inside the powered supports at all points along the face, a quadratically weighted average of the airflows measured at various stations along the face was calculated: [n2Qavg =Qi Ii / It(2)i=1] where [Q, avg = average airflow for analytical purposes, ft3/min (m3/sec); Q= airflow at station i, ft3/min (m3/sec); 1= length of segment represented by Q, ft (m); h= length of longwall face, ft (m): and n= number of quantity measurement stations.] The quadratic weighting scheme was chosen because the

Jan 1, 1992

By Alexander N. Winchell

"Location: The Menominee district has been described geologically in several units, because the known iron-bearing formations of the larger region are not a really connected. From the commercial and mining standpoint, however, the district em¬braces, all that territory extending from a point about five miles east of Vulcan to a point a few miles west of Iron River, an east-west distance of about fifty miles, and from a line about two miles south of Vulcan to one ten miles north of Crystal Falls, a north-south distance of about thirty-five miles. This area is largely in the State of Michigan, but includes more than two hundred square miles in Florence County, Wisconsin. The chief towns of the district are Vulcan, Iron Mountain, Iron River, and Crystal Falls, in Michigan, and . Florence in Wisconsin. The Wisconsin portion of the district has not produced a large portion of the output of the area.History: The earliest reports of iron ore in the Menominee district were made by J. W. Foster and S. W. Hill, who conducted a geological exploration from Lake Superior to Green Bay in the fall of 1848. It is a remarkable fact that in spite of their plain statements regarding their discoveries, these state¬ments were apparently forgotten for a period of nearly twenty years. Foster states that ""about two miles southeast of the lower falls (of the Twin Falls on the Menominee River) near Sec. 30, T. 40 N., R. 30 W. there is a large bed of specular iron ore associated with the talcose and argillaceous slates. It makes its appearance on the north side of the Lake and can be traced a mile and a half in length and in places is exposed one hundred feet in width."""

Jan 1, 1920

By H. E. Rutherford

Monterey Coal Company has begun a geologic monitoring program in order to better understand our in-mine geologic conditions and to apply the knowledge gained to our mining operations. Two methods are used to collect information. The first is a monthly examination of conditions throughout the mine using a rapid mapping technique. The second is the detailed mapping of specific events encountered during mining such as faults and roof falls. The data gathered from both methods is correlated with operational statistics to create a geologic/production database. From the database, a monthly evaluation of mining conditions is made. Also, the database has proved useful in such areas as forecasting roof conditions and examining how faulting has affected mining operations.

Jan 1, 1984

By Ernest E. Thurlow

The Geology Division of Northern Pacific Railway Company has adapted to its exploration efforts field procedures for geochemical sampling and semi-quantitative analysis which have been developed through research by the U. S. Geological Survey. The sampling is done in conjunction with reconnaissance geologic mapping on aerial photographs or during field checking of maps which have been prepared largely by photogeologic interpretation.. Stream sediment or soil samples are taken and readily soluble combined heavy metals are extracted with ammonium citrate followed by colorimetric titration with dithizone at the sample site. The effectiveness of this approach has been demonstrated both in positive and negative results, thereby assisting in the elimination of large areas of land from further immediate attention and in providing targets for followup exploration. An occasional sample is submitted for spectrographic analysis as a check on the possible presence of other elements of economic significance. Field laboratory procedures are also being implemented for determining molybdenum, mercury, and other metals which may be valuable in themselves or useful as pathfinder elements in outlining mineralized areas. A lead-zinc occurrence in Oregon and a copper deposit in Montana were readily detected and outlined by stream sediment and soil sampling and a heavy metal anomaly that lacks obvious interpretation has been found in northwestern Montana. Detailed mapping and additional sampling are followed by other exploration techniques if warranted.

Jan 1, 1964

By Richard J. Lewandowski

Corrosion and product contamination have been difficult problems for extractive metallurgy industries in the U.S. because of the highly active chemicals used. During the past twelve years, other industries, particularly the chemical and paper segments, began to combat this problem with some degree of success using newer materials of construction, including reinforced plastics. These materials are made by combining a corrosion resistant thermosetting resin with a glass fiber reinforcing material and are used to con¬struct hoods, stacks, blowers, tanks, towers, pipe, and equipment of the most complex configurations. For service in contact with aggressive chemicals, the equipment is most often fabricated with the bisphenol-A fumarate polyester resins because of their resistance to corrosive attack. Data from both laboratory work and case histories of field applications are presented-for many common chemicals found in extractive processes. Information is also presented concerning design standards and recommended construction procedures

Jan 1, 1970

Underground mining alters ground condition, producing a disturbance in the ground water regime. The level of disturbance is dependent on the local hydrology, geology, and type of mining. Serious damage is sometimes caused by ground water- when mine roofs collapse, causing subsidence. Subsidence is either unplanned, where pillars are inadequate to provide support; or planned, where total extraction occurs over a large area. The primary objective of this study is to investigate the effects of mine subsidence on the ground water hydrology in the Warrior Coal Basin. Underground openings resulting from coal mining activities have been the most significant cause of subsidence problems in the Warrior Coal Basin, the main source of coal in Alabama. This problem will be even more serious in the future because 19 of Alabama's 24 billion tons of coal reserves are classified as an underground source (Tolson, 1982).

Jan 1, 1987

By William Gleason

While a fleet of 100 t (110 st) haul trucks were busy removing overburden from the open pit mine in the distance, a host of dignitaries, including congressmen and California state representatives, gathered for Molycorp?s official groundbreaking ceremony at the Mountain Pass Mine on April 20. The mine, recognized as arguably one of the richest rare earths deposits in the world, is at the center of Molycorps? strategic ?Mine to Magnets? plan. It aims to secure America?s future supply of rare-earth-dependent technologies by developing a strong domestic rare earth industry. Molycorp identifies rare-earth-dependent technologies as those that cannot be produced without rare earth materials. The list of these technologies is long and growing. It encompasses everything from personal electronics and batteries for hybrid cars to permanent magnet generator wind turbines and national defense applications.

Jan 1, 2011

By Myron W. Mellor

Our efforts at McNally, to find a better way to mechanically separate particles from liquid in a slurry have led to the development of two new centrifuges. The first unit utilizes a slotted opening screen as the filter media and retains all plus 200 Mesh and most of the 200 by 300 Mesh particles. The second unit is a solid bowl centrifuge with a novel method of removing the solids and delivers an effluent containing as little as 300 PPM solids in suspension. The first unit was designed to separate particles in the range of about 1 MM x 0 or smaller top size from the liquid slurry and produce solids having low surface moisture content, and a liquid concentrate containing a low percentage of solids. A prototype of this unit has been in the field undergoing tests for over two years. A few of these test results are shown in Tables I & 11. Testing has been mostly limited to the field of coal, how- ever this does not mean that the machine would accept only coal slurries. The machine has produced a dewatered product having as low as 5.5% surface moisture, and an effluent containing as low as 1.4% solids and handled slurries containing from 15 to 50% solids by weight.

Jan 1, 1975

By Naomi H. Harley, Daryl E. Bohning, Isabel M. Fisenne

INTRODUCTION Underground mines in many parts of the world have elevated levels of short-lived 222Rn daughters. Lung cancer implicating exposure to short-lived daughters is documented in the U.S., Czechoslovakia, Canada, Sweden, the U.K., France and Newfoundland. An elevated lung cancer mortality (in excess of that expected) has been observed when cumulative exposure to alpha emitting short-lived 222Rn daughters (218Po, 214pb 214Bi 214Po) is greater than about 60 working level months (WLM) [1]/ (Hewett, D. 1979). This is equal to an absorbed alpha dose of about 30 rads to shallow basal cells in bronchial epithelium. Long-lived alpha emitters are also present in underground mines, and especially uranium mines because of airborne particulates containing uranium. The 238U parent of this primordial series supports other long-lived emitters 234U 230Th, 226Ra, Pb(210Po) which are in some degree of radioactive equilibrium with the parent 238U. Airborne particulates can be present due to drilling on the face of the ore body as well as in all parts of the mine through resuspension from the mine floor. Particles from 1 µm to about 5 µm penetrate the nose with reasonable efficiency and deposit primarily in the tracheobronchial tree. They are removed by ciliary motion (the bronchial escalator) but deliver an alpha dose to basal cells in bronchial epithelium during clearance in the same manner as short-lived 222Rn daughters. It is the purpose of this work to indicate the alpha dose to basal cells in bronchial epithelium delivered by the long-lived emitters 234, 238U. The dose calculations reported here based upon a few measured values of these isotopes in air in uranium mines in New Mexico and Colorado. MEASURED 234, 238U IN URANIUM MINE ATMOSPHERES In 1979, the U.S. Bureau of Mines undertook a study to evaluate personal monitors to be worn by miners to measure short-lived 222Rn daughters. One of these devices sampled air at 100 cm3/min through a 13 mm glass fiber filter, with a small pump worn on the belt. Alpha particles emitted by 222Rn daughters on the filter were measured continuously by a thermoluminescent dosimeter (TLD) chip. Each monitor was worn by a miner for a 170 hour working month and approximately one cubic meter of air was sampled during this period. Six different mines were selected for the test in New Mexico and Colorado. The mines used either wet or dry drilling methods. Miners in each location were equipped with the personal monitors. Subsequent to their use in evaluating the shortlived daughters, Dr. Robert Droullard of the Bureau generously gave us these filter samples along with a few blank glass fiber filters from the same box of filters used in the study so that long-lived emitters present in these mine atmospheres could be determined radiochemically. Four of the samples have been run for 234, 238U. The radiochemical procedure for uranium is adapted from USDOE, Environmental Measurements Laboratory Manual (Harley, J.H., 1976). Briefly, the samples were placed in platinum crucibles, spiked with 232U tracer and pretreated with nitric and hydrofluoric acid. The residue was fused with potassium fluoride to transpose to pyrosulfate. The fused cake was dissolved in 7 [N] hydrochloric acid and the solution passed through an anion exchange column to isolate uranium. Iron was removed using mercury cathode electrolysis. Uranium was electrodeposited onto platinum dies and counted using solid-state alpha spectrometry. The samples from each type of mine (wet and dry) were analyzed. The samples in the "wet" mine in New Mexico were selected on the basis of the original TLD measurement because they were near the maximum occupational standard for radon daughters. These samples should also represent upper limits to longlived activity encountered, since they were obtained at drilling operations on the face of the ore body. Samples collected in the "dry" mine in Colorado were pot associated with a particular location in the mine and should be representative of a month long overall exposure in many locations and operations. The values are shown in Table 1. The two uranium isotopes are in equilibrium and their alpha activity

Jan 1, 1981

By T. Y. Yan

A method has been developed to remove calcite from the leaching circuit in the uranium in situ leaching system. The process involves injecting the leachate and a pH control agent tangentially into an inverted cone reactor containing calcite seed catalyst. The leachate can be treated at high throughput to obtain clear effluent containing 5 ppm or lower Ca. Both lime and ammonia are effective pH control agents and consumed according to stoichiometry.

Jan 1, 1983

By S. Mischler, J. Organiscak, S. Klima, C. Seaman

"Researchers at the National Institute for Occupational Safety and Health’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six hollow cone water sprays from three manufacturers: static swirl chamber sprays from Spraying Systems (BD-3, BD-5) and Steinen-Hahn (SH-3, SH-5), and movable swirl chamber sprays from Repair King (RK-3, RK-5). Water flow testing was completed at three operating pressures (60, 80, and 100 psig) where both sets of sprays (3-series and 5-series) produced similar water flows, deviating less than 8% from the average water flow rate at each pressure. Airflow induction testing was completed at 80 psig using a hot wire anemometer to take air velocity measurements upstream of the spray nozzles. Respirable dust capture efficiency testing was completed in a 14.5-m3 (512-ft3) closed system dust chamber at 80 psig. The dust capture efficiency ranged from 7.2% to 9.9% for the 3-series nozzles, and from 5.3% to 7.1% for the 5-series nozzles. Sprays were also analyzed using a Cloud Aerosol and Precipitation Spectrometer (CAPS), which uses light scattering to count and size the airborne water droplets from each spray. In both cases, Spraying Systems sprays produced the largest mean droplet size, followed by Steinen-Hahn and Repair King sprays, respectively. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in underground coal mining operations in the United States. The U.S. Mine Safety and Health Administration (MSHA) now requires coal mine worker respirable dust exposure to be no more than 1.5 mg/m3 average over the actual working shift (CFR 30-70.100, 2016). Potential overexposure to respirable dust by continuous miner, roof bolter, and shuttle car operators may be prevented if proper safety and health practices are implemented as detailed in the mine’s ventilation plan (CFR 30-75.371, 2016). Water sprays are a necessary component of an underground coal mine ventilation plan. They are important on the continuous mining unit for moving air and removing respirable coal dust from the breathable airstream. MSHA requires underground coal mines to include the number, types, location, orientation, operating pressure, and flow rate of operating water sprays in their mine ventilation plans (CFR 30-75.371, 2016). Water sprays can become clogged, requiring the sprays to be properly checked, maintained, and replaced in order to continue meeting the ventilation requirements described in the mine ventilation plan.In an effort to eliminate the problems with spray clogging, Repair King has developed self-cleaning movable swirl chamber hollow cone water sprays (RK-3, RK-5). The spray’s movable swirl chamber is designed to only open when water pressure is applied to the spray nozzle, preventing the nozzle from clogging. Anti-clogging sprays could improve mine production by reducing the amount of time spent servicing clogged sprays. Also, these sprays could improve health and safety of miners since they would continue to suppress and capture dust and continue to move airflow at the face, while a clogged spray loses this ability until it is cleaned or replaced manually. The objective of this research was to assess the comparability of the Repair King sprays with the most commonly used sprays in underground coal mines using performance criteria. An assessment of the sprays self-cleaning or anti-clogging capability was not conducted."

Jan 1, 2017

By S. S. Peng

In this paper, the precise definitions for a number of commonly used subsidence parameters are given. The subsidence parameters have been determined using an integrated approach for 110 subsidence cases collected in the major US coal fields. Attempts have been made to establish empirical formulae for the parameters. The results of this study indicate that some traditionally-held concepts should be changed.

Jan 1, 1995

By Yuemin Zhao, Daniel Tao, Rick Honaker, Maoming Fan

"Froth flotation is the most widely used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles around 700 nm in diameter can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubbles on the flotation performance of different particle size fractions of coal was investigated using a bank of 10-L flotation cells, a specially designed 50-mm inside diameter column and a 152-mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during the froth flotation process improved flotation efficiency. The use of nanobubbles in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.IntroductionFor minus 0.6 mm fine coal or minus 0.15 mm ultrafine coal particles, froth flotation is known to be the most efficient and the most cost-effective separation technique. However, flotation efficiency decreases sharply with ultrafine and relatively coarse coal particles. Studies have shown that the low flotation efficiency of ultrafine particles is mainly due to the low probability of bubble-particle collision (Yoon et al., 1989; Ralston and Dukhin, 1999). Enhanced flotation of fine and ultrafine coal can be achieved by increasing collision and attachment probabilities.The top size of particles that can be recovered by flotation depends on the combination of mineral properties and flotation devices. Turbulence in flotation devices is an important factor that affects the stability of bubble-particle aggregates. Even in the flotation of fine particles, bubble-particle detachment can significantly influence the kinetics of flotation taking place in mechanical cells, which provide intensive turbulent agitation (Deglon et al., 1999). Coarse particle flotation is more difficult, because increased agitation is required to maintain particles in suspension and coarse particles are more likely to detach under turbulent conditions (Mankosa and Kohmuench, 2002; Soto and Barbery, 1991). More efficient attachment of particles and improved flotation rate has been observed when tiny bubbles coexist with conventional-sized flotation bubbles (Attalla et al., 2000; Tao et al., 2010; Fan et al., 2010a, b, c, d; Fan et al., 2012)."

Jan 1, 2015

By Henry R. Colen

When we were asked to prepare a paper on gold to be part of the Economics of Precious Metals session, our immediate thought was that we should address the question of supply. Are the existing mines of the world capable of filling the demand for gold? We recognized that gold does not conform to the normal pressures of supply and demand. Major new sources of production and increased sales might have a very short term effect and depress the price but this does not last very long. Those forces that affect gold prices are very different from the ones economists normally deal with. Factors such as mass psychology, political tensions and fear are certainly more important to the gold price than supply and demand in today's world.

Jan 1, 1981

By A. L. de Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS). Biologically produced hydrogen sulfide has economically very interesting application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By C. Roos

"Nearly every input to a mine plan is based on an estimate. The estimates may be from sample data, historical information, models, or personal opinion, but in all cases, these values are simply expected values (means). In real life, we do not get to iterate the exact conditions at our mining operation many times to ensure that that average value is attained. The expected value also tells us nothing about the spread of values that that input might take on. The result is a significant amount of unquantified uncertainty in our mine plans. Unfortunately, it is often too expensive or time consuming to update planning processes and software. This paper presents a proof of concept spreadsheet scheduling tool that can be utilized to incorporate many geologic realizations (simulated models) into the mine scheduling process. While this POC is not intended to be a detailed model of uncertainty, it is to show that there are stepping stones available for mine planners to begin to embrace uncertainty and produce more achievable plans without requiring a significant change in their planning process. INTRODUCTION Mining companies have included quantifying uncertainty, or at least risk, as a requirement of project justification for many years, however many times this process lags behind the traditional mine planning process and the results are rarely used to improve the plan. Nearly every parameter used in a mine plan is an estimate and the mine planning engineer should recognize and even embrace the inherent uncertainty in those parameters and its effect on their forecast results. While many of the uncertainties are beyond the scope of the traditional mine plan (e.g. global market uncertainty, socio-political uncertainty, environmental uncertainty), some uncertainties can, and should, be included in the mine planning process. Many mining engineers have incorporated techniques such as Monte Carlo Simulation or Discrete Element Simulation to understand the range of productivity that can be expected for an operation but most still rely upon one estimated model for what is likely the critical component of technical uncertainty, the geologic resource. Modern geostatistical methods can provide multiple ore body realizations to provide a thorough unbiased “picture” of the geologic uncertainty but most traditional mine planning techniques are not formulated to allow for multiple (100-200) realizations of each material quality/grade parameter. Commercial software companies and research groups are progressing with development of tools that can incorporate geologic uncertainty, and even optimize extraction plans in the uncertain environment. Unfortunately, this author believes that a significant number of mining operations will not be able to adopt these techniques due to the computational requirements of the advanced techniques and the costs associated with implementing proprietary software. In an attempt to encourage mining engineers to embrace the inherent uncertainty in their mine plans, this paper presents a cost-effective alternative that can be developed in-house, at any mine, to schedule mid to long-term mine plans while continuously monitoring the uncertainty in the results. The author hopes that by demonstrating the usefulness of such a system that mining companies will encourage engineers, geologists, and geostatisticians to find ways to incorporate this powerful data into their processes and procedures."

Jan 1, 2017

By H. Sevim

Belt network simulators developed in the last two decades are reviewed. Critical parameters in belt network design are identified, and the capabilities of belt simulators in providing values of these parameters are investigated. An alternative design model that optimizes values of the critical parameters is introduced. To illustrate the capabilities of the alternative model, a real life case is treated and the outcomes are discussed.

Jan 1, 1990

By J. J. Gusek

An 81 hectare (200 acre) tailings impoundment at a taconite operation in Wyoming that ceased operations in 1983 has been a source of blowing dust. The site qualified for reclamation under Wyoming's Abandoned Mine Land (AML) reclamation program. The ultimate reclamation construction included: incorporating commercially available organic amendments and fertilizers into a 300 mm (12 in) thick "cap" of a sterile clay loam cover material, lowering the water level in an adjacent flooded mine pit that was feeding uncontrolled seeps into the tailings basin, constructing a wide tailings pond spillway that allows flood control while minimizing seasonal water level fluctuations in the pond, and building rock berms and rock snow fences for wind erosion control and soil moisture preservation. Tree planting in the protective wind/snow shadows of rock berms and rock snow fences, and the plugging of a decant pipe are planned for future work.

Jan 1, 1998

By S. G. Britton

Thin seam mining presents unique challenges when management or economic conditions require significant productivity increases. These challenges are increased depending upon the presence of various external factors such as labor unions, Federal and state regulations, and market characteristics. This paper explores the turn-around situation occurring at Tanoma Mining Company (TMC), a medium-sized underground coal mining company in central Pennsylvania, USA. Using a systematic approach of improving management controls and direction, labor relations, and communications, coupled with an intensive upgrade/rebuild/replacement program for equipment and systems used at the mine, TMC has begun reversing its' cashflow position from negative to positive within two years.

Jan 1, 1991