Search Documents

By W. A. McKinney

In conventional dump leaching of porphyry mine strip wastes, many years are required to extract up to 20 percent of the copper from the contained sulfide minerals. Furthermore, none of the molybdenum, gold, or silver in the strip wastes is recovered by current leaching practices. Because mineralization occurs predominately along fracture planes, breaking of the rock during mining operations liberates and concentrates some of the metal values in the fines. Research shows that upgraded fines can be screened from mine wastes and froth floated for early recovery of copper, molybdenum, gold, and silver. For example, screening a dump sample assaying 0.35 percent copper as chalcopyrite removed about 20 percent of the copper as minus 1/4-inch material that analyzed 0.6 percent copper. About 35 percent of the molybdenum and 20 percent of the gold and silver also reported in the fines. Crushing the mine dump sample to minus 3 inch before screening increased the distribution of copper and molybdenum in the minus 1/4-inch screen fraction to 28 and 50 percent, respectively. Similar results were obtained by screening fines from two other large samples of mine waste dump materials. Flotation studies established that the enriched minus 1/4-inch fines from the three dump samples could be effectively concentrated. Comparative testing revealed that the combination of froth flotation of fines and acid-ferric sulfate leaching of the coarser fraction enabled doubling the recovery of copper over direct leaching of the samples. In addition, significant amounts of molybdenum, gold, arid silver were recovered by flotation.

Jan 1, 1970

By Michael A. Werner

"A Yieldable Structure for Use in Areas of High Rock Stress & Deformation." Rock stress of up to 9000 psi have been recorded in the mines of the Coeur d'Alene Mining district. Associated with these large stresses are rock fractures and deformation. In order to maintain openings required for mining, large wood preparation structures are constructed to provide access to the work areas for men and materials. These wood raise preparation structures are costly to construct and maintain. Therefore a steel-foam concrete structure was designed and proposed for testing which would be less costly to construct, require no maintainence and maintain its structural integrity while allowing up to 53 inches of wall rock deformation.

Jan 1, 1984

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By Michael M. Kimberley

Gold is sufficiently valuable that concentrations as small as 1 p.p.m. may support low-cost mining. Mindful of this, Sunoco Energy Development Company (Sunedco) obtained fire-assay analyses on some sulfide-rich sandstone encountered during routine drilling. Initial fire-assay values from independent laboratories indicated some significant gold values and independent analysis by atomic-absorption spectroscopy also indicated detectable gold at economically interesting concentrations. Sunoco geologists realized the potential for spurious results inherent in both fire assaying and atomic-absorption spectroscopy. Fire assaying that relies on gold measurement by weight requires perfect separation of gold from all other elements, Imperfect separation may artificially enhance apparent gold concentrations. Atomic-absorption-spectroscopy (AAS) measurements are potentially subject to interferences from other elements. For example, Beamish and Van Loon (1977, p.4) report AAS measurements of 4 p.p.m. Au to be characteristic of completely barren soil samples when samples are prepared by standard dissolution in HC1 to form solutions of about 10,000 p.p.m. total cations (mostly Na, Ca, Mg, Al, and Fe) .

Jan 1, 1981

By A. G. Nitschke, I. Ossenbühl, W. Dolsak, J. Dase

"The authors have successfully developed an innovative rehabilitation concept, which meets actual technical standards and minimizes the impact on the operation of a key conveyor tunnel. A flexible and stepwise ground support rehabilitation program utilized a combination of yielding steel arch sections with grout filled fabric hoses, which represents a fast and safe backfilling support system. The system was developed and successfully installed at Bingham Canyon Mine, the world’s largest open pit copper mine, which also includes numerous underground structures. The mine is owned and operated by Kennecott Utah Copper (RTKC) a fully owned subsidiary of Rio Tinto. The system was implemented at a conveyance tunnel, which was originally designed as a railroad tunnel, but was re-commissioned and is currently used as a conveyor belt tunnel to transport ore from the open pit to processing facilities outside the mine. The existing structure showed signs of overstressing due to movements in the surrounding rock mass, which had to be addressed with a yielding support system in order to provide safe access into the tunnel. However, the impact on the conveyor belt operation due to support installation was to be limited to the bare minimum. Keywords: rehabilitation, yielding support, mining, stabilization, and grout filled fabric hose.PROJECT DESCRIPTION The C6 Tunnel is considered a critical asset for the operation of the Bingham Canyon mine as it comprises the standard route for transporting crushed ore from the open pit to the processing facility on a continuous conveyor belt system. The C6 tunnel was originally built as a railroad tunnel. Construction was completed in 1959. The original horse-shoe shaped cross section of the tunnel was 18 feet wide and 24-1/2 feet high [8]. The tunnel length was approximately 18,000 feet. During its service life, the railroad tunnel has undergone several transformations. The length of the tunnel towards the Bingham Canyon pit was shortened over the course of mining operations and the railroad tracks in the tunnel were removed. The invert was partially backfilled (3 feet typical) and a 72 inches belt conveyor was installed. Currently, the C6 Tunnel is nominally only approximately 21 feet high and 15,000 feet long. Ground Support and Rehabilitation Measures prior to 2014 The C6 tunnel was mined mainly with conventional mining methods, using drill & blast as the typical one. However, the weak geological sections, such as those encountered in the Fortuna fault, were excavated by shaping and chipping with machine-held moils [8]."

Jan 1, 2015

By Robin Dill, Wei Song, Andrew Perham, Leo Martin

"AECOM completed a subsurface exploration program for an 18-foot diameter, approximately 4-mile long rock tunnel project in Hartford, CT. The tunnel crosses the regional geologic trend through the middle of a sedimentary basin, passing through four separate rock formations, including two volcanic flows. Faulting is prevalent, with at least 15 faults encountered during the site investigation. Severe artesian flows were also experienced in several of the borings, requiring highly specialized drilling equipment. Sixty-two borings and associated testing were performed to characterize the structural geology, hydrogeology, rock properties and ground conditions. A phased program was carefully planned and implemented with participation of geotechnical and geologic specialists, with thoughtful evaluation along the way to react to the ground conditions encountered, and make appropriate refinements. This paper will discuss the subsurface program details; the integrated efforts used to effectively characterize the ground; and will summarize the final characterization presented in the GBR. PROJECT DESCRIPTION The South Tunnel Conveyance and Storage Tunnel project is part of the Metropolitan District (MDC’s) Long Term Control Plan to address discharges to various water bodies throughout the greater Hartford area. This program includes a main conveyance and storage tunnel; a tunnel boring machine (TBM) launch shaft and retrieval shaft; adit tunnels with associated drop shafts and connection structures; consolidation conduits and manholes; and a tunnel pump station (TPS) at the downstream end of the main conveyance tunnel. AECOM is serving as prime designer for the MDC on this project. The main conveyance tunnel (hereinafter referred to as the “South Tunnel”) will be a deep rock tunnel with an invert depth of approximately 180 feet at its downstream end and approximately 218 feet at the TBM retrieval shaft. The tunnel will have a finished diameter of 18 feet. The tunnel will rise in grade at a slope of 0.1 percent to its upstream end. Total invert depth along the deep tunnel alignment ranges from about 180 ft. to as high as 320 feet. The total length of the tunnel will be 21,754 feet. The South Tunnel will be constructed using a shielded TBM and fully lined with pre-cast concrete segments."

Jan 1, 2016

By R. Zhang, S. Azam, S. Liu, J. H. Golbeck, V. Kurashov, S. Bhattacharyya

Free radicals (FRs) present in coal dust directly influence the interaction behavior between lung cells and dust particles. FRs are atoms or groups containing unpaired electrons, with strong chemical reactivity and a short lifespan. FRs which are quite persistent in natural environments, termed environmentally persistent free radicals (EPFRs), have recently received much attention as new environmentally hazardous substances. EPFRs present on coal dust serves as an active intermediary to catalyze reactive oxygen species (ROS) production by oxygen molecules endangering mine workers’ health. Many EPFR species may be bonded to the particle surface or trapped within the particle during coalification and can be modified with progressive size reduction through cutting at the mining face or crushing/pulverization in the plant. This study measured EPFRs for lignite, sub-bituminous, and anthracite coal dust at various sizes. We especially focused on EPFRs for submicron coal dust prepared by cryogenic methods. The outcome of this study will directly improve the free radical-dependent toxicity quantification and ultimately contribute to the size-dependent coal dust toxicity quantification.

Mar 2, 2022

By Stan Tang, Yiming Sun, S. Amir Reza Beyabanaki, N. Sathi Sathialingam

The Kurve mixed-use development project including a 22-story tower at 2801 Sunset Place was constructed on a site consisting of a roughly rectangular-shaped lot at the intersection of Wilshire Boulevard and Hoover Street in Los Angeles. Two Metro Red Line tunnels, with depths of approximately 30 feet and 58 feet, respectively, cross below the building at distances of approximately 1 foot to over 63 feet from the site. This paper presents numerical modeling performed to evaluate the ground and tunnel behavior in response to building construction. Results of geotechnical instrumentation and monitoring undertaken during the building construction are also discussed.

Jun 13, 2023

By Gregory M. Rumbaugh, Todd Kostecki, Christopher Mark

From 2015 to 2021, five massive pillar collapses occurred at four underground stone mines in the eastern United States. These events resulted in powerful airblasts that damaged mine infrastructure and mobile equipment, seriously injured miners, and disrupted underground travelways. Each of these pillar collapses propagated through the overlying strata, causing a subsidence basin on the surface. Pillar collapses are particularly hazardous for miners because they can occur with little warning and can affect miners that are far from the pillar collapse area. The following case studies show that certain factors may increase the likelihood of a pillar collapse. For instance, each of the five events involved the collapse of at least twelve benched pillars with width-to-height ratios (w/h) of 0.8 or less. This study elaborates on

By Peter Zhang, Daniel Su, Mark Van Dyke, Heather Dougherty

The integrity of shale gas wells in longwall chain pillars under the influence of longwall mining is a safety concern for both coal and gas operators. Previous modeling studies of gas wells in longwall pillars have shown that a FLAC3D model can predict longwall-induced stresses and deformations in gas well casings with reasonable accuracy. The predicted casing deformations can be verified by multi-finger caliper survey. This study concerns the influence of longwall mining on eight shale gas wells in a shale gas well pad located in the chain pillars between two adjacent longwall panels under 1,030 feet of cover. FLAC3D modeling was performed to predict longwall-induced deformations in gas well casings based on site-specific mining and geological conditions. Small deformations less than 0.5 in were predicted in the intermediate casing above 600 ft depth, and very small casing deformations less than 0.15 in were predicted below 600 ft due to high abutment pressure and high frictional resistance along the weak bedding interfaces. After the first panel was mined, a 56-arm caliper survey was performed on one of the wells to measure the longwall-induced casing deformations in the intermediate casing. The predicted casing deformations were then compared with the measured deformations, which indicated that the prediction was generally in good agreement with the measurement in terms of deformation locations and magnitudes. Findings from this study provide valuable information not only for stability assessment of shale gas wells in longwall chain pillars but also for developing engineering guidelines to preserve casing integrity through adequate pillar and casing design.

By Peter Zhang, Daniel Su, Berk Tulu, Bo Hyun Kim, Zoheir Khademian

Over 2,000 shale gas wells have been drilled in the Pittsburgh Seam longwall reserves. As longwall panels are laid out, some of these shale gas wells must be located in longwall chain pillars. With longwall mining on both sides and the constraint of chain pillar size, gas well in chain pillars are subjected to longwall-induced ground movements and stresses, which could induce deformations in gas well casings Casing deformations are associated with several factors such as overburden geology, surface topography, setback distance, and casing construction. Overburden geology is one important factor that largely determines the locations and levels of deformations in gas well casings Previous NIOSH gas well research has found that casing deformations above the coal seam horizon are smaller under deep cover than unde shallow cover and that casing deformations could occur at the coal seam horizon under deep cover. Recent mine-by cases have provided more insights into the locations and amount of longwall-induced casing deformations as well as the potential occurrence of a large casing deformation at the coal seam horizon. This paper presents three recent mine-by cases with shale gas wells in the chain pillars between two adjacent longwall panels under different overburden depths. Casing deformations were measured by multi-finger caliper surveys and predicted with numerical modeling. With the established numerical model, the effect of overburden depth was further analyzed to investigate the potential occurrence of a large casing deformation at the coal seam horizon under deep cover. These mine-by cases not only provide a general demonstration of how overburden depths can affect longwall-induced stresses and deformations but also give a good indication about the level of casing deformations that could occur under different overburden depths. The study concludes that (1) casing deformations reduce with increase of overburden depths at the gas well; (2) a cementing alternative with production casing uncemented is an effective means to eliminate production casing deformations; and (3) large plastic casing deformation could occur in the production casing at the coat seam horizon under deep cover. The experience and knowledge gained from these mine-by cases would help longwall operators and gaza companies to take appropriate measures to minimize the influence of longwall mining in shale gas wells in chain pillars.

Jun 25, 2024

By W. L. Staker

The Bureau of Mines investigated selective extraction of Au and Ag from a low-grade Au ore containing Hg. Gold and silver were extracted from the ore in cyanide slurries, and Hg extraction was suppressed with sodium or calcium sulfide. Maximum Au extraction and minimum Hg extraction were obtained using solutions containing 0.34 lb NaCN/ton of solution. Increasing the cyanide concentration increased Hg extraction without increasing Au extraction. Mercury extraction from the ore was suppressed with 0-5 to 2.9 Pb CaS/lb Kg in the ore. Gold-to-mercury ratios of 100:1 to 400:1 were obtained in the leach solution, and on the activated carbon in a CIP circuit.

Jan 1, 1983

By Dennis C. Parker

The Porters Creek clay is mined for its absorbent properties. The formation is part of the Upper Mississippi embayment and is recognized in Alabama, Mississippi, Tennessee, Kentucky, Illinois, and southeast Missouri. Major minerals in order of abundance are Montmorillonite, Quartz, Illite, Kaolinite, and Chlorite. Mining consists of open pit operation utilizing track loaders or scraper. The clay is dried or hardened in rotary kilns and crushed to size by roll crushers. The clay granules are sized and air classified prior to storage for shipment or packaging. Granules are sold for pet absorbents, oil absorbents, anti-skid material, fertilizer, and pesticide carriers.

Jan 1, 1979

By Louis W. Cope

The Compañía El Zapote Yacimiento Y Minas, S.A. has an ore body containing 650,000 tons of 0.185 oz/t gold ore in Mexico. Metallurgical testwork has been done to determine the response of this ore to several possible processing schemes. The paper describes the rationale for selecting the Silver State Mining Co. methods in Colorado. Plans for developing the mine and building the treatment plant are described in detail in the paper. Estimates of capital and operating costs are included.

Jan 1, 1984

By T. Owen

Not since 1917 has a foreign company developed a standalone, grass roots gold mine in Russia. With. Russia's political changes of the late 1980s, development of mineral prospects once again beckons foreign investors. In 1990, Cyprus Amax began aggressively searching for such an opportunity. Early in 1997, production will commence at the Kubaka gold project located in the Russian Far East, near the Arctic Circle. The Kubaka project is a 1,750-tonne per day open-pit operation that will produce more than 300,000 ounces of gold per year. This paper discusses the challenges of locating such a prospect, doing business in Russia, developing supply lines, identifying work force capabilities, gaining government approvals, securing financing, arranging for gold sales and ultimately building a facility in this arctic region.

Jan 1, 1997

By John B. Gustavson

Gold was first discovered in Alabama in 1830. Before a decade had passed more than 20,000 people were employed in the various gold districts scattered across east-central Alabama. By 1849 most of the presently defined gold districts were known with such towns as Arbacoochee, Chulafinnee, Goldville, Pinetucky, and Idaho being the principal mining camps. The California gold rush of 1849 signaled the end of intensive prospecting in the Alabama Piedmont for the precious metal. Reactivation of many of the old gold districts has been attempted several times since 1849. Significant activity and development took place between 1874 and 1880, 1888 and 1916, and 1929 and 1936. Locally, some of the development met with moderate succes. The last productive gold mine in Alabama ceased production in 1935. The sharp increase in gold prices since 1973 has caused renewed interest in the potential values of gold of the Alabama gold districts. Most of the gold workings have been abandoned for nearly 75 years and are for the most part inaccessible for convential property evaluation. The early gold miners and prospectors in Alabama were more intent upon finding and mining the valuable metal than in recording their activities for future generations. No matter how interesting or historically significant these records might have been the miners kept no records and left behind them few maps as clues to their activities. Inasmuch as most of the old gold districts have been extensively mined and prospected during the past 150 years, there is very little chance of finding large deposits through conventional outcrop prospecting methods. Similarly, the present geologic knowledge of the various districts is insufficient to launch successful exploration programs looking for large blind lode deposits in new locations within the general gold bearing region.

Jan 1, 1975

By F. G. Miller

In mid-1972 we determined that a fresh approach to coal mining research was needed for the industry as well as for Bethlehem. The reasons to us were obvious: Productivity was in the throes of a steady decline, and labor and maintenance costs were spiraling upward. Yet, despite this predicament, nowhere in the U.S. at that time was there a comprehensive and coordinated research and development plan in the offing. The Bureau of Mines had not yet been charged with such a responsibility, and industry was content to rely on machinery manufacturers for innovations. After studying our own mining practices, the state-of-the-art of mining research elsewhere, and development work by manufacturers, we presented a comprehensive research package to our management at the end of 1972. The ideas and experience of many operating and management personnel in our Corporation contributed to the formulation of the final plan as approved.

Jan 1, 1976

By Z. Rogovin

In order to develop more accurate procedures for scale-up and design of semi-autogenous-grinding mills through detailed mathematical models, a better understanding of the charge motion and rock/ball segregation is needed. To achieve this a 0.61 m (2.0 ft) diameter x 0.305 m (1.0 ft) length plexiglas mill was constructed as a scale model of a commercial SAG mill. Rock motion in the rotating mill was simulated using various sizes of ceramic balls. Quantitative measurements of dynamic angle of repose, water and slurry motion, holdup and size segregation of the charge were taken. In addition, a video-presentaiton (available to the public) was prepared to elucidate charge and water motion at various mill speeds, charge volumes, rock size distribution and flow rates.

Jan 1, 1985

By Allen D. Graham

The coal industry in South Africa is briefly outlined. Test- work carried out on bulk samples of coal in the laboratory and used in the design of the Van Dyks Drift washery are described. Factors affecting the selection of equipment and the designed capacity of the plant are discussed. A description of the crushing plant, washery and load out section is given together with performance data obtained in the final acceptance tests. New features incorporated in the Van Dyks Drift plant and in more recent plants of the Group are outlined.

Jan 1, 1982

By Jorge A. Benitez Muro

Within the exploration programs carried on by the Consejo de Recursos Naturales No Renovables, the one with the largest coverage (more than 75, 000 square kilometers) is the northern Coahuila Exploration Project. Due to its nature, geochemical exploration methods were selected to obtain quick results. The program included essentially, three main stages : 1. - A regional geochemical stream sediment survey. 2. - Semi-detailed studies of the anomalous areas selected in the previous stage, and 3. - Detailed exploration of the promising areas. To the date, the first two stages have been completed, and the third one is being carried on. The work was started on september 1972, and it will probably take one more year before drilling can be started, but at the end of stage three it is expected that at least 5 important targets will have been detected. The regional work was conducted by 3 field crews, but the detailed program is being done by only one.

Jan 1, 1974