Search Documents

By E. R. Bauer

In response to the mandates in the MINER Act of 2006, NIOSH conducted refuge alternatives research that included characterizing the utility, practicality and survivability of refuge chambers and outby safe havens. NIOSH also prepared and delivered a report to Congress in late December 2007 that summarized the findings of the research, included recommendations concerning the design and performance specifications for refuge alternatives, and focused on specific information that could inform the regulatory process on refuge alternatives. This document highlights NIOSH's research and recommendations concerning refuge alternatives, survivability evaluations of refuge chambers, and presents a brief review of the current deployment of refuge chambers in underground coal mines in the U.S. The research has lead to the conclusion that refuge alternatives have the potential for saving the lives of mine workers if they are part of a comprehensive escape and rescue plan, and if appropriate training is provided. DISCLAIMER: ?The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.?

Jan 1, 2009

By Bhaskar B. Thapa

The proposed Caldecott fourth bore will consist of a two lane highway tunnel along California State Route 24 near the City of Oakland. The proposed design and construction sequence for the 15-m-diameter tunnel are based on the New Austrian Tunneling Method (NATM). The initial support system incorporates combinations of shotcrete, rock dowels, lattice girders, spiles, and grouted steel pipe canopies. The final lining is cast-in-place reinforced concrete. A waterproofing membrane and drainage system are placed between the initial and final linings. State Route 24 is a lifeline route, required to be open to emergency vehicles within 72 hours after a major earthquake, defined as having a return period of 1,500 years and a peak ground acceleration of 1.2 g. Although the seismic design criteria are stringent, the design of the tunnel lining system is ultimately controlled by static ground loads in the weak rock along the alignment.

Jan 1, 2008

By K. Ward

The Environmental Protection Agency (EPA) is beginning to provide compliance assistance visits to various industries, including mining, for Emergency Planning and Community Right-to-Know Act (EPCRA) compliance. The EPA inspectors may consist of a multi-media team deployed to review systems and procedures for EPCRA Sections 302, 304, 311, and 312. The Team’s focus may include emergency response plans, training programs, qualifications of personnel, and release notification protocols. This presentation takes a look at the EPCRA compliance challenges faced by Arizona copper mining and processing facilities.

Jan 1, 2001

By Alan K. Burton

Massive increases in the productive capability of open pit nines after World. War II were in a large part made possible by the introduction of ever larger trucks and the supply of a seemingly bottomless ocean of inexpensive and readily accessible oil. Over a period of about 25 years, a variety of technological developments permitted a tenfold truck payload increase, from about 32 tonnes (35 tons) to 320 tonnes (350 tons). There is no, doubt that this was a remarkable achievement resulting in impressive benefits of scale as well as the ability to control what would otherwise have become an intolerable traffic congestion problem in today's large open pit mines. It became fashionable and economically possible during this time to mine large quantities of low grade material and to tolerate very high stripping ratios. As tine has gone by and as easier to get at and higher grade deposits have been depleted, ore grades have tended to decline while stripping ratios have increased. The alternative to reduced revenues has been an ever increasing demand to step up production which in turn has led to a continuing demand for ever larger and larger trucks. While a larger truck has had the effect of reducing the cost of the operator per unit of material moved and of reducing traffic congestion, it has not specifically addressed the subject of fuel cost.

Jan 1, 1981

By Luzheng Chen

Pulsating high-gradient magnetic separation (PHGMS) of fine hematite from tailings was studied using a pilot PHGMS separator to investigate the possibility of its application in industry. The results of this investigation indicate that PHGMS is effective for recovering fine hematite from the tailings and greatly improved the separation performance compared with the conventional high-gradient magnetic separation at the same conditions. By applying the pilot separator with a 1-mm rod matrix to a tailings containing 28.76% Fe, a concentrate assaying 54.35% Fe with 35.89% recovery was achieved. It was found that the separation performance of the pilot separator closely correlates with the main pulsating parameters, i.e., pulsating stroke and frequency. It was also found that a change in the wire diameter of the rod matrix from 2 to 1 mm causes a weak drop in concentrate grade but results in a considerable rise in recovery. This finding proves that the improved performance achieved by the pilot separator is attributed to the pulsating of slurry and to the use of a 1-mm rod matrix. When the first commercial SLon-2500 PHGMS separator with a 1-mm rod matrix was applied to recover fine hematite from the tailings, the results duplicated those achieved with the pilot PHGMS separator.

Jan 1, 2009

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. The sheer volume of sensors results in mines not being able to keep the sensors calibrated. When a sensor goes off calibration, it results in errors which can severely impact plant economics. Normally, these errors are not detected until the error grows and becomes a large (“gross”) error. Undetected errors are not remedied until the next calibration, which on average are a year apart Beamex (2019) [1] across all industries. Classical statistical methods that depend on linear relationships between input and response variables are typically used to find gross errors, but are not effective for highly non-linear and non-stationary operations in mining and mineral processing industries. Calibration of sensors is time-consuming and generally requires physical intervention that results in equipment downtimes causing production losses. Therefore, in situ detection methods are warranted that do not require physical removal of sensors to compare with standard measurements or well-calibrated sensors. Data-mining based techniques and algorithms have high success rate in tackling such problems. This paper presents results from a groundbreaking multi-year big data research project whose goal was to develop data-mining-based original techniques in a multi-sensor environment to identify when sensors start to stray, rather than wait for errors to grow. The carbon stripping (gold) circuit in the Pogo Mine of Alaska was selected for this project. Maintaining strip vessel temperatures at optimum levels is crucial for maximizing gold recoveries at Pogo, and hence the focus was on the temperature sensors of the two strip vessels. An automated algorithm to detect errors in strip vessel temperature sensors was developed that exploited data from multiple sensors in the strip circuit. This algorithm was able to detect with a high success rate when bias errors of magnitude as low as ± 2% were artificially induced into strip vessel temperature data streams. The detection times of about 1 month were much less than the industry average calibration frequency of 1 year. Thus, the algorithm helps detect errors early, without stopping the circuit. The algorithm alarms can serve as triggers when calibrations are done. Experimental methodology along with results, limitations of algorithms, and future research are also presented in this paper.

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. The sheer volume of sensors results in mines not being able to keep the sensors calibrated. When a sensor goes off calibration, it results in errors which can severely impact plant economics. Normally, these errors are not detected until the error grows and becomes a large (“gross”) error. Undetected errors are not remedied until the next calibration, which on average are a year apart Beamex (2019) [1] across all industries. Classical statistical methods that depend on linear relationships between input and response variables are typically used to find gross errors, but are not effective for highly non-linear and non-stationary operations in mining and mineral processing industries. Calibration of sensors is time-consuming and generally requires physical intervention that results in equipment downtimes causing production losses. Therefore, in situ detection methods are warranted that do not require physical removal of sensors to compare with standard measurements or well-calibrated sensors. Data-mining based techniques and algorithms have high success rate in tackling such problems. This paper presents results from a groundbreaking multi-year big data research project whose goal was to develop data-mining-based original techniques in a multi-sensor environment to identify when sensors start to stray, rather than wait for errors to grow. The carbon stripping (gold) circuit in the Pogo Mine of Alaska was selected for this project. Maintaining strip vessel temperatures at optimum levels is crucial for maximizing gold recoveries at Pogo, and hence the focus was on the temperature sensors of the two strip vessels. An automated algorithm to detect errors in strip vessel temperature sensors was developed that exploited data from multiple sensors in the strip circuit. This algorithm was able to detect with a high success rate when bias errors of magnitude as low as ± 2% were artificially induced into strip vessel temperature data streams. The detection times of about 1 month were much less than the industry average calibration frequency of 1 year. Thus, the algorithm helps detect errors early, without stopping the circuit. The algorithm alarms can serve as triggers when calibrations are done. Experimental methodology along with results, limitations of algorithms, and future research are also presented in this paper.

By Frank Pepe, Nestor Garavelli

The 2023 Rapid Excavation and Tunneling Conference (RETC) will be held in Boston, MA and will include the presentation of 133 papers divided into 20 technical sessions during the 3 day conference that were selected from over 200+ papers that were submitted to the committee. The selected papers are included within this book to provide a comprehensive recap of the conference while also providing a source of reference for contractors and engineers in the future. The selected papers will include contributions from all divisions of the tunneling industry plus risk management and best contract practices. Boston is known to the tunneling industry for its complex and difficult tunneling history, specifically of recent memory the Central Artery/Tunnel Project also know as the “Big Dig” of the 1980s and early 1990s. The selection of Boston as a host city was fitting from a historical perspective and as avenue for the city to present its upcoming tunnel projects. RETC began in 1972 with the idea of sharing ideas, design and project construction experience, and new technology, between contractors, designers, owners and suppliers. The ability to provide a single location every other year for all facets of the tunneling industry to gather and discuss the aforementioned was and still is viewed as a way to help the tunnel industry grow. The lessons learned from completed projects, the advancement of technology which could be implemented into design and the presentation of new projects by owners/designers and contractors allows for the limits and complexity of upcoming projects to be expanded beyond our current capabilities. Our industry has never been as busy as it currently is, and we are seeing more future projects coming out for solicitation across all business sectors. With the good fortune that all of us have been blessed with one of the biggest challenges that we have been faced with is the shortage of future management on all levels for our projects including the labor force. We all want our industry to continue to grow and succeed, our most important assets are the people that we employ. Investing in the education and continued training of our work forces to be up to date with the latest technology and methods is the key to our success. This also includes develop, recruiting and mentoring of young students graduating college to join our industry so that we can all continue to grow. We hope that all those attending the conference will have the ability to attend as many sessions as possible and to expand their network within our industry. As in past years, scholarship students will be in attendance and we encourage all to offer these students an opportunity to visit jobs, attend learning sessions or future internships to expand their interest in our industry that needs an injection of young engineers to contribute and lead our future Rapid Excavation and Tunneling Conferences. The program chairs wish to thank the session chairs, co-chairs, authors, and other members of the RETC Executive Committee for their dedication to this conference. Last but certainly not least, we give special thanks to the SME staff for their hard work and enthusiastic support in making this conference possible.

Dec 1, 2023

By H. K. Lin

The effect of metallic iron fines on froth flotation of a sulfide ore was examined by comparing the flotation results with and without iron fines present in the flotation feed. Mild steel and ceramic laboratory ball mills were used to grind 600 g sulfide ore charges. The mild steel ball mill generated approximately 4.6 g of iron fines (0.8% of the ore charge mass) when grinding to a product size of 80% passing 200 mesh (75 mm). When a low dosage of a weak xanthate collector was used in flotation, the impact of the iron fines on sulfide flotation was marked. Higher dosages of stronger xanthate collectors rendered the impact of the iron fines much less significant. Consumption of the collectors by the powdery iron fines is believed to cause the differences observed in the flotation results. A galvanic effect on flotation was not evident in this study. The impact of the iron fines on silicates depression was also examined.

Jan 1, 2008

By S. H. Jason Choi

The Systems Conveyance and Operations Program (SCOP) is being implemented to convey tertiary-treated effluent to Lake Mead near Las Vegas, Nevada. The Reach 3 Tunnel Project is part of SCOP. The tunnel?s planned location along and across the Las Vegas Wash creates challenging tunneling conditions. A number of feasible excavation and initial support methods are being considered during the final design stage. This paper describes how the tunnel construction options were refined based on anticipated tunneling conditions and compatibility between tunnel excavation and initial support methods. A brief description of the most significant characteristics of the anticipated ground conditions is included for the purpose of discussion.

By E. Jackson

This paper describes highlights of the Placer Dome MiniMole project - the development and testing of a robotic machine for mining narrow ore veins. A prototype hydraulically controlled robotic machine was built and tested. The machine provided a platform for testing numerous cutters in the field. Other cutters, e.g. undercutting devices, were tested in the lab. Extensive analyses were done on specific energies and cutter penetration. Three sets of quarry trials were done, then the machine was tested in an underground mine. Rock UCS values varied from 180 MPa to 230 MPa. The paper includes lessons learned and recommendations based on the project findings.

Jan 1, 2007

By Nikhil Dhawan, Ashwini Kumar, Yogendra Pratap, Himanshu Tanvar

India does not possess any soluble potash reserves and depends completely on imports. In this study, an attempt has been made to recover potash (K) values from the mica sample employing thermal and mechanical routes followed by leaching. Direct leaching of mica in different lixiviants is found to be ineffective with very low K-dissolution (1–5%). Heat treatment with different fluxes, such as NaCl, NaOH, and CaCl2, is carried out and almost 85% K-values are recovered. Mechanical activation of mica and with different calcium additives is carried out to recover potash values. K is recovered in leach solution in the form of soluble salts, such as K2CO3, K2SO4, and KOH, and leach residue consists mainly of calcium-alumino-silicates. Using mechanical activation with flux, it is possible to recover >95% K-values from mica sample. Mechanical activation with calcium-based flux is found sustainable in the recovery of K-values from mica.

By Steve Kral

The dramatic rescue of nine Pennsylvania coal miners trapped nearly 90 m (300 ft) underground for77 hours probably would not have happened without the high technology equipment and improved mine rescue training techniques available today. By now, most everyone has heard the story of the accident that occurred at the Quecreek Mine near Somerset, PA. At about 9 pm on Wednesday, July 24, the miners were drilling coal in the room-and-pillar mine. Their drilling accidentally punched through to the adjacent, abandoned Saxman Mine. Old mine maps of the Saxman Mine led Black Wolf Coal, Quecreek’s owners, to believe they were between 60 to 90 m (200 to 300 m) away from the abandoned mine. Those maps proved to be inaccurate.

Jan 1, 2002

By Bhaskar B. Thapa, Michael T. McRae, Johannes V. Greunen

This paper describes the preliminary design of the fourth bore of the Caldecott Tunnels along State Route 24 in Oakland, California. The paper focus is on two major aspects of the project: initial support system design and seismic design. The initial support system was designed based on the New Austrian Tunneling Method (NATM).NATM provides the required flexibility to accommodate the variable ground conditions in the weak, folded, and faulted rock along the alignment. The seismic design provides a final lining system that meets serviceability requirements for a 1,500 year seismic event with an estimated peak ground acceleration of 1.2g.

Jan 1, 2007

Longwall mining has existed in Utah for more than half a century. Much of this mining occurred at depths of cover that significantly exceed those encountered by most other U.S. longwall operations. Deep cover causes high ground stress, which can combine with geology to create a coal burst hazard. Nearly every longwall mine operating within the Utah’s Book Cliffs coalfield has been affected by coal bursts.

Jan 7, 2020

By António Fiúza, Anthony Danko, Patrícia Leitão, Aurora Futuro, Cristina Vila, Lurdes Dinis

The average global recovery rates for processing scheelite ores by physical methods are normally in the range 50 to 70%, and it is problematic to attain a minimum grade of 60% WO3 in the concentrates without penalizing further this yield. Direct hydrometallurgical processing of low-grade concentrates or medium- to high-grade ores may become an interesting global economic alternative as it allows increasing the recovery rate, avoiding major penalizations due to the grade of the concentrate and increasing the added value of the final product. Leaching of scheelite by sodium carbonate presents several advantages such as its selectivity regarding the dissolution of troubling metals like iron and aluminium, allowing for a simple and flexible process diagram. However, it has the disadvantage that it is performed at high temperature and pressure with a high consumption of reagents. The feasibility of leaching is appraised by the extraction yield and selectivity, but also by the operating cost. Considering these aspects, a relevant objective of the research was to transform alkaline pressure leaching into a feasible processing alternative directly applicable to both medium- and high-grade ores and simultaneously to low- and high-grade concentrates produced by physical methods. The research used ore samples and low-grade concentrates from a typical skarn orebody as well as high-grade concentrates from a chalcopyrite-scheelite orebody. Different operating conditions were tested. Temperature, pressure and reagent concentration showed to be fundamental, but not exclusive, in determining the leaching behaviour. The operating conditions are milder than the ones generally proposed in the literature or currently in use in industry, but with higher carbonate consumptions. The research was oriented towards potential industrial implementation allowing for the application of optimization methods and straight scale-up to pilot-plan design and project.

By D. He

In China, the total reserves of vanadium, reported as V2O5, in stone coal is 118 Mt (130 million st). Recovering vanadium from such a large resource is very important to China?s vanadium industry. The technology now being used to recover vanadium from stone coal has the following two problems in the leaching process: a low recovery of vanadium and high acid consumption. To resolve these problems, a new leaching technology is proposed. The effects of factors such as H2SO4 concentration, liquid-solid ratio, temperature and time, and the types and additions of additives were studied. By adding 1.5% (by weight) CaF2 and leaching the roasted residue of stone coal with 5.4% (by weight) sulfuric acid at 90°C for 12 hours at a liquid-solid ratio of 2 mL/g, the leaching degree of vanadium reached 83.10%. This proposed leaching technology gives a feasible alternative for the processing of roasting residue of stone coal and can be applied in the comprehensive utilization of stone coal ores in China.

Jan 1, 2008

By Randy Vranes

Sophisticated information technology, quality management systems and a commitment to the environment has allowed Solutia’s Soda Springs phosphate mine and elemental phosphorus plant to reduce operating costs, improve product quality and contribute to the sustainable development of Idaho’s industrial minerals. Soda Springs background The Soda Springs phosphate mine and plant is a joint venture between Monsanto and its operating partner, Solutia Inc. The operation is based in southeastern Idaho in the Western Phosphate Field. The plant is located about 275 km (170 miles) northeast of Salt Lake City, UT and about 4 km (2.5 miles) north of the town of Soda Springs.

Jan 1, 1999

By J. A. Ober

"In 2015, the estimated value of nonfuel mineral production in the United States decreased by 3 percent from that in 2014 (Table 1), mainly as a result of decreased metal and metallic mineral prices, especially iron ore, copper and precious metals. Lower metal prices were attributed to decreased consumption, especially in China and increased global inventories. Several U.S. metal mines were idled in 2015, including the only U.S. rare earths mine at Mountain Pass, CA. Downstream processors also were affected, with smelters and refiners either shutting down or idling production lines. Increases, however, took place in the value and quantity of production of industrial minerals, especially those used in the construction sector, including cement, construction sand and gravel and crushed stone. Trends in mineral-related sectors of the domestic economy, except for iron and steel manufacturing, aluminum manufacturing, coal mining and metals mining, all experienced growth (Table 2).Discussion of mine production is frequently segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, which have higher production quantities but are lower-valued materials, such as crushed stone or construction sand and gravel. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of construction aggregates are orders of magnitude larger than those for most other mineral commodities thus making direct comparisons based on weight meaningless (Fig. 1).Mineral industry performanceThe estimated value of domestic nonfuel mineral production, including metals ($26.6 billion) and industrial minerals ($51.7 billion), in 2015 declined to a total of $78.3 billion, from $80.8 billion in 2014 (Table 1). However, as shown in Fig. 2, minerals remained fundamental to the United States economy, contributing to the real gross domestic product at several levels, including mining, processing and manufacturing finished products. Net exports of mineral raw materials and old scrap were $14.4 billion. Domestic raw materials, along with domestically recycled materials, were used to produce mineral materials worth $630 billion. These mineral materials, including aluminum, brick, copper, fertilizers and steel, and net imports of processed materials (worth about $32 billion) were, in turn, consumed by downstream industries with a value added to the gross domestic product estimated to be $2,490 billion."

May 1, 2016

By Bhawani Singh, A. K. Dube, B. Singh

At least three hydroelectric tunnels constructed during the last decade through the lower Himalayan region in India have met with serious problems of supporting in squeezing ground conditions. Steel ribs under went intolerable deformations requiring rectification to provide space for concrete lining which delayed the projects inordinately. In an attempt to choose a rational method of predicting rock load, the authors have compared rock loads estimated from various classification systems and elasto-plastic theory with observed values. The deficiencies of the classification systems have been highlighted to show that the combination of elastoplastic theory and tunnel instrumentation programme provides better guidelines for the design of tunnel supports in squeezing ground conditions.

Jan 1, 1981