Search Documents

By Ole Rud Bendixen

Topsoe has developed a Wet gas Sulphuric Acid (WSA) process which effectively recovers SO2 in off-gases from non-ferrous smelters and roosters. The product is concentrated sulphuric acid of typically more than 96 wt% irrespective of SO, concentration in off-gas. The process does not generate any waste products or waste water and does not use any absorbents or other chemicals. In the process, up to 99.3% of the SO2 is converted catalytically into SO3, which reacts with water in the gas, hereby forming gaseous sulphuric acid. The acid is condensed in a WSA condenser of proprietary design. Excellent heat economy and practically no sensitivity to the water balance mean that no extra sulphur burning is required at any S02 concentration, The process is especially well suited for treating off-gases where the SO2 content is lower than approx. 5-6%, and it is a good alternative to a complete renovation of a smelter. However, also off-gas from flash smelter may be treated. The process has found good use in both molybdenum and lead roosters. An example from a molybdenum roaster in Chile shows that 97-98wt% acid is produced from a 2.3 % S02 gas. This plant is situated in the outskirts of Santiago and represented a major local source of SO2. The plan was started in May 1993.

Jan 1, 1996

By Rui Mao, Ke-Xin Nao, Jian-Liang Zhang, Xiang-Nan Xu, Meng-Fang Wei

"In this research, fundamental characteristics of dust and sludge containing iron from the dusting system of sintering process, blast furnace, oxygen converter and rolling process in steel enterprise were studied by chemical analysis, X-ray diffraction analysis, optical microscope analysis, scanning electron microscopy analysis, particle size analysis and other analysis means. Development direction of resource utilization for dust and sludge containing iron from steel enterprise was put forward on the basis of above study.IntroductionDust and sludge containing iron for steel enterprise mainly come from the dusting system of sintering process, pelletizing process, blast furnace, oxygen converter, rolling process and other related process. Iron content of dust and sludge is between 30% and 70%, and they also contain certain content of carbon, calcium oxide, magnesium oxide and harmful elements [1-3]. Output of dust and sludge is determined by raw materials conditions, technological processes, equipment configuration and management level. Dust output in sintering process accounts for about 2% to 3% of the sinter production, while dust and sludge from iron making and steel making process respectively take up 3% to 4% of hot metal and crude steel production, and the solid waste from rolling process accounts for about 0.8% to 1.5% of the output of rolled products [4,5]. Dust and sludge contains Fe, CaO, MgO, C and other valuable resources, it will not only result in the waste of resources, but also cause serious pollution to environment ifthe dust and sludge are not recycled. China's crude steel production in 2012 is about 700 million tons and output of dust and sludge containing iron is nearly 60 million tons, so, it is of great significance to have a resource recycling for dust and sludge containing iron from steel enterprise."

Jan 1, 2014

By Manju Gurung, Birendra Babu Adhikari, Keisuke Ohto, Hidetaka Kawakita, Katsutoshi Inoue, Shafiq Alam

Novel bio-adsorbent gel was prepared by immobilizing functional groups of glycidyltrimethyl ammonium chloride, a kind of quaternary ammonium chloride, onto polymer matrices of persimmon extract for the recovery of precious metals such as palladium(II) and platinum(IV) from chloride media. It was found that this adsorption gel exhibits high selectivity to gold(III), palladium(II) and platinum(IV) over base metals such as copper(II) and iron(III) while crude persimmon extract, the feed material, exhibits high selectivity only for gold(III). From the adsorption isotherms study, the maximum adsorption capacities for gold(III), palladium(II) and platinum(IV) were evaluated as 3.30, 1.67 and 1.00 mol/kg, respectively. Those for palladium(II) and platinum(IV) are higher than those of simple quaternary ammonium chloride type of chemically modified persimmon tannin gel and commercially available anion exchange resin.

Jan 1, 2016

By Hui Zhang

The leaching behavior of palladium powder in aqueous solutions containing NaCI or N'H4Cl was investigated. Cupric ion was used as an oxidant for the dissolution reaction. The effect of a number of leaching parameters such as temperature, concentration, stirring speed and surface area on the leaching rate was studied. The leaching system containing chloride and cupric ion was found to be very effective for the dissolution of metallic palladium. Based on the experimental results the overall leaching rate was believed to be controlled by a chemical reaction step. The dissolution rate of palladium was found to be first order with respect to the concentration of cupric ion and second order with respect to the concentration of chloride.

Jan 1, 1996

By Ehsan Khajeh

In this study, the permeabilities of Al-15.5wt%Cu and Al-19.5wt%Cu have been determined by solving the full Navier-Stokes equations on 3D geometries of interdendritic channels obtained by X-ray microtomography (XMT). The samples for XMT were sectioned from different positions in directionally solidified cylinders in order to obtain a variety of microstructures for each composition. The flow has been solved using a 2nd-order accurate Finite Volume Method (FVM) approach. The effect of employing uniform or unstructured mesh on the calculated permeability has been studied. The Marching-cube triangulation method was necessary to extract accurate surfaces for unstructured volume meshing. Calculated values of permeability for this range of solid fractions show partial agreement with previous experiments. Observed deviations are attributed to the difficulties of experimental permeability measurements.

Jan 1, 2009

By Dumitru Mitrica, Vasile Soare, Elvira Alexandrescu, Mihai Ghita, Marian Burada, Petru Moldovan, Raluca Maria Florea

"Aluminum metal matrix composite Al-Si /SiCp was prepared by reactive gas injection and subsequent remelting. The influence of the remelting process on the microstructure and physicalmechanical properties of the resulted material was investigated. Samples resulted from the synthesis process contained silicon carbide agglomerations in the vicinity of primary silicon and large pore concentrations. In-situ formed silicon carbide presented mostly a polymorphic structure with particle sizes varying from 1 to lOµm. Physical and mechanical properties were largely influenced by the porosity distribution. The remelting process provided a decrease in the composite material porosity and pore size, with significant improvements in the particle distribution and physical-mechanical properties of the composite material. Additions of up to lwt.%Mg in the starting alloy improved the in-situ carbide formation and particles distribution in the solidified material. However, stable and large particle agglomerations were detected in the material in absence of conventional stirring or controlled solidification techniques.IntroductionThe remarkable properties of composite materials (yield strength, stiffuess, hardness and resilience at a reduced specific weight) make them attractive for applications in automotive, aerospace and military industries. Particle reinforced aluminum metal matrix composites (PAMMC) are known for their high strength to weight ratio. The recent development of P AMMC created the possibility to obtain large particles concentrations, exceeding 10% by volume ofreinforcement (SiC, AIN, Al203, etc.). The improvement ofhigh temperature strength and wear resistance made them appropriate for the use in automotive applications, such as the pistons, rotors, disc brakes, and propeller shafts [ 1]. The present main disadvantage of the P AMMCs is their high costs for obtaining and processing related to the final product performance. In order to benefit from the advantages that offer composite materials properties a reasonable production cost - performance ratio must be obtained [2]. Recent innovations in the manufacturing of aluminum-based metal matrix composites provided notable performance improvements but no feasible solutions were found for lowering their present high prices."

Jan 1, 2014

By P. R. Khangaonkar

The industry of tin ore mining, beneficiation and smelting gives rise to a number of waste products like the beneficiation plant wastes (called amang), tin smelting slags, refinery dross etc. Some of the wastes deserve treatment to obtain economically useful products or to recover the metal values. The paper describes studies conducted on two materials, viz., struverite-middling (struverite-magnetic tin), which is an intermediate product of beneficiation circuits of tin tailings, and tin-smelting slags. The struverite middling was studied for treatment by chlorination using carbon tetrachloride, so as to yield vapour products separable by convenient condensation. The treatment was also found to lead to a tin-rich product amenable for treatment by known hydrometallurgical routes. The tin smelting slag was studied by alkali-leaching so as to avoid any dissolution of iron and it was possible to obtain an iron-free product solution suitable for high purity tin recovery.

Jan 1, 1996

By Andriy Burbelko, Daniel Gurgul, Wojciech Kapturkiewicz, Marcin Gómy

"The mathematical model of the globular eutectic solidification in 2D was designed. The proposed model is based on the Cellular Automaton Finite Differences (CA-FD) calculation method. The model has been used for studies of the primary austenite and of globular eutectic grains growth during the ductile iron solidification in the thin wall casting. The model mentioned above takes into account, among other things, non-uniform temperature distribution in the casting wall cross-section, kinetics of the austenite and graphite grains nucleation, solute diffusion and non-equilibrium nature of the interphase boundary migration.Some aspects of stochastic nature of the solidification processes are taken into account. The results of the CA solidification modeling have been shown, that differences between cooling curves obtained in the same conditions of the casting solidification may be a result of the stochastic nature of the grain nucleation.The results of modeling were compared with the experimental microstructure. The model is well worked for thin walled ductile iron casting, for fast solidification process.IntroductionNodular graphite cast iron, also known as ductile iron (DI), has major applications in critical engineering parts due to its mechanical properties and castability. The mechanical and physical properties of this material depend on the shape and number of the graphite grains andmicrostructure of the metallic matrix.Solidification of DI was a subject of many computer modeling programs described in literature [ 1-5], in which the stationary conditions of carbon diffusion in austenite is pre-assumed. Recently, a tendency for production of thin-walled castings has been observed [ 6-8]. In this technology, the process of the fast solidification may be very far from equilibrium and steadystate conditions [9].The purpose of the present work is a two-dimension model development for simulation of the DI structure formation during the solidification in the condition of non steady-state temperature and diffusion fields in the thin-wall casting.Model of process The CA-FD is one of the known methods of the simulation ofmicrostructure formation during the solidification [ 10, 11]. In the CA microstructure modeling the outer grain shape is the result of the simulation and does not superimposed beforehand. The model development for a onephase microstructure evolution is a subject of the numerous researches [12 -23]. Model of the eutectic solidification of DI in the uniform temperature field and superimposed cooling rate is known [24]."

Jan 1, 2013

By QinGuo, Shenghui Guo, Jinhui Peng, Linqing Dai, Libo Zhang

This paper adopts a simple and novel preparation. Taking cellulose as a template, a tubular morphology structure of micro/nano ZnO crystals was obtained by microwave roasting at high temperature. The higher the microwave roasting temperature, the larger the degree of crystallization. The experiments indicate that the best photo catalytic effect can be obtained at 850 : At this temperature, the oxidation of cellulose is complete. Large quantities of hexagonal shaped ZnO crystal can be observed, specifically the (0001) crystal face. Under ultraviolet-visible irradiation, taking long arc mercury lamp as light source, the material had good photocatalytic activity. The decomposing efficiency of methylene blue reaches 97% in 60min, which is superior to that of preparations without templates at the same temperature.

Jan 1, 2016

By Garrett May

We present a periodic technique for measuring the thermal conductivity of thin, disk-shaped samples. In samples of this type, temperature measurements must be made across the sample faces and are therefore subject to large error due to the interface resistance between the temperature sensor and the sample. The technique uses measurements of the amplitude and phase of the periodic temperature across both a reference sample and the unknown material at several different frequencies. Modeling of the heat flow in the sample allows the simultaneous determination of the thermal parameters of the sample as well as the interface resistance. The technique is demonstrated on nanocomposite samples less than 1.0 mm thick.

Jan 1, 2008

By Hideo Nakae, Hideki Yamaura, Toshiaki Kimura

"In 1968 J. N. Reding et al. suggested processes for fabricating composites. According to their patent, decompression atmosphere, which occurs during the reaction between magnesium and oxygen and/or nitrogen in the closed system, causes the spontaneous infiltration of melt into narrow spaces such as ceramic preforms. However, they did not report the proof of this phenomenon or the industrial manufacturing method. Therefore, this research measured the pressure change among SiC particles surrounding molten aluminum. As a result, the pressure reduction during the Mg reaction was identified. Moreover, the existence of Mg3N2, which improves the wettability between Al alloy melt and SiC particles on the interface, was observed on the surface of particles. Applying these two phenomena, a new process for the manufacturing of cast discontinuously reinforced aluminum composites (DRA) was developed. This new method is expected to produce DRA without additional pressure.IntroductionWith the increasing demands for light-weight materials in the automotive and aerospace industry in recent years, ceramic particulate reinforced aluminum matrix composites called DRA (Discontinuously Reinforced Aluminum Composite) have been receiving significant attention because of its lightness, superior abrasion resistance, high heat conductivity and low thermal expansion [1-3]. Consequently, DRA was considered for electronic parts such as heat-sinks or a base for power semiconductors, and began to be applied for automotive parts including brake drums, discs, cylinder liners, pistons and so on [4- 6]. However, high machining cost is one of the significant barriers to widespread use ofDRA. One solution to this problem is the adoption of cast DRA that can be produce to near-net shape, reducing machining cost."

Jan 1, 2000

By S. K. Kawatra, T. C. Eisele

"Recent advances in microbiology have made the application of biotechnology to metallurgical processes possible. Hydrometallurgy stands to gain the cost from the use of microorganisms, as they are useful for both dissolution aids and for removing metals from solution. The development of genetic engineering techniques promises to greatly increase the importance of bioprocessing of metals and minerals by the year 2000.In this paper, the basic effects of microorganisms on metallurgical processes are reviewed, and the applications which are currently either in use or near being used are presented. Representative data collected at Michigan Technological University is also given.IntroductionMany hydrometallurgical operations exist which are thermodynamically possible, but which are industrially impractical due to slow kinetics, high reagent costs, or the need for a highly corrosive environment. However, recent discoveries in microbiology indicate that in many cases these difficulties can be reduced greatly by the action of bacteria and other microorganisms (1-8).A major advantage of using living organisms in hydrometallurgy is that once the culture is established the microorganisms produce their own reagents either from the material being processed or from low-cost nutrient supplements. They thus allow extremely complex chemical reactions to be carried out at reasonable cost. The major drawback of using microorganisms is their inability to tolerate extremely high temperatures, excessive concentrations of toxic metals, or very highly acidic, alkaline, or corrosive conditions. However, the complex reactions which bacteria make possible frequently eliminate the need for such extreme conditions. Also, in recent years a number of organisms have been isolated from such exotic environments as hot springs and deep-ocean vents which can tolerate temperatures higher than was previously thought possible for any organism, and can catalyze a number of metallurgically important reactions (8)."

Jan 1, 1988

By L. H. Gevantman

A program for the compilation of evaluated physical and chemical numerical properties data is being pursued at the National Bureau of Standards within the Office of Standard Reference Data. This program is being sponsored by the Department of Energy and managed by the Battelle Office of Nuclear Waste Isolation in Columbus, Ohio. The intent is to assemble a reliable body of numerical properties data concerning candidate mineralogical materials in which high-level radioactive wastes are to be buried. The ready accessibility of the data to site designers and the credibility achieved through the evaluative process are designed to help assess and compare the feasibility of each candidate material for use as a disposal site. Both generic and site-specific data are to be assembled. To date, generic rock salt properties have been assembled and published by the NBS as NBS Monograph 167. Details of the effort to produce this book are discussed.

Jan 1, 1982

By N. Gopalakrishnana, R. Beccard, S. Lourdudoss, R. Holz, M. Deschler

"Rapid growth of conducting and/or insulating InP, GaAs, Gao.47In0.53As, and GaAs0.6Po.4 on one or more of (001), (110), (111)A, (3ll)A and (3ll)B surfaces by Hydride Vapour Phase Epitaxy (HYPE) is demonstrated. The maximum growth rate of the binaries lies between 12 and 300 µm/hr and of the ternaries between 7 and 170 µm/hr. A simple model is developed to describe the influence of crystallographic orientation on temperature dependent growth rates. The growth rates predicted by the model is compared with the experimental values. Room temperature resistivity of insulating InP:Fe can be as high as 5xl09 ohm cm. Temperature dependent differential resistivity is also analysed. This feasibility of growing conducting and insulating layers rapidly on different orientations is very useful for electronic and optoelectronic devices.IntroductionRecently there is a renewed demand for very thick layers of III-V compound semiconductors for high performance electronic and optoelectronic devices [1]-[2]. Long wavelength high speed lasers that can be modulated up to 30 GHz necessitate epitaxial growth of semi-insulating (SI) layers [3]. There is also an increased interest on the growth of epitaxial layers on surfaces other than (001) surface. Epitaxial growth of these materials on such surfaces is of theoretical importance besides being technologically relevant. These demands led us to focus on the growth of conducting and insulating III-V compounds by Hydride Vapour Phase Epitaxy (HYPE). lnP, GaAs, Gao.471no.s3As on lnP and GaAso.6Po.4 on GaAs were grown as conducting materials using Low Pressure HYPE (LP-HYPE) on (001) 2° off substrates. Gao511no.49P on (001) GaAs substrate and lnP on lnP substrates of (001), (110), (l 11)A, (31l)A and (3 ll)B orientations were grown as semi-insulating materials using Atmospheric Pressure HYPE (AP-HYPE). In this report we present the growth aspects of these materials. We also present a simple model on the growth of InP on substrates of various orientations. The theoretically obtained temperature dependent growth rates are compared with the experimental values. Differential resistivities of semi-insulating lnP grown on substrates of various orientations as a function of temperature are also summarised."

Jan 1, 1998

By Ross R. Bhappu

A theoretical and experimental investigation into pyrometallurgical refining of chloride leach/electrowin copper is described. The two techniques investigated were (i) vaporization and (ii) gaseous halogenation. Experiments were carried out with a packed bed of electrowon copper crystals and a boat of melted copper crystals. Nitrogen gas and Freon 12/nitrogen mixtures were used as the carrier and reac.tive gases. Vaporization was found to be effective in removing Bi, Pb and S while halogenation was effective. in removing As, Bi, Pb, S and Sb. Silver resisted all attempts at removal. Iron was removed but less effectively than the other impurities.

Jan 1, 1985

By R. V. Kumar

"The use of sensors to monitor gaseous species in industrial processes is discussed. All of the existing systems have disadvantages. Sensors, based upon solid electrolytes, which can be placed directly into the gas stream are attractive but many also respond to oxygen, need to be sealed at high temperatures and require a separate reference. This paper describes sensors, usually based upon two electrolytes, which do not respond to oxygen and do not require high temperature gas seals or separate references. The application of these sensors to the measurement of carbon dioxide, sulphur dioxide and trioxide and hydrogen chloride is described. These sensors can be placed directly into the gas stream at elevated temperatures.IntroductionOn-line gas sensing is becoming more important as concerns regarding the environment mount. There are many established techniques for monitoring gases in industrial processes, with applications in safety monitoring, chemical analysis or process and emission control. Flue gas analysis involves the greatest technical complexity, requiring several sophisticated capital-intensive spectroscopic instruments for different species as well as needing highly skilled operators. There are also several instruments, based upon aqueous electrochemistry, which are available for the analysis of the gases S03, S02, N02 but these require that the gases are sampled at high temperature and cooled, prior to analysis. These instruments cannot be considered as giving on-line measurements of the gas composition. Furthermore, the power requirement of these instruments frequently precludes battery operation for field and domestic use."

Jan 1, 1997

By Xiangwen Wang

Electrodeposition of lead metal from high purity brine electrolytes containing lead chloride (PbCI,) was conducted so as to assess the feasibility of electrowinning lead-metal directly from aqueous chloride electrolytes. Tests were performed at 65 and 80°C (338 and 353°K). Characteristic features of the deposits, on both lead and graphite substrates, were correlated to operating parameters associated with: electrolyte temperature, current density and total lead- concentration. Photomicrographs of these morphological features were obtained by use of Scanning Electron Microscopy (SEM).

Jan 1, 1993

The direct removal of lead ions from D2EHPA-kerosene using metallic zinc as the reducing agent was evaluated. The electrochemical process, called galvanic stripping, is a potential alternative stripping technique when standard chemical methods are not adequate. Four parameters found to be important in the rate of lead removal were studied in a factorially designed experiment. The variable evaluated included D2EHPA concentration, temperature, zinc surface area and solution agitation. Temperature and surface area were found to be the most significant, while agitation and D2EHPA concentration had less influence on the reaction. An activation energy of 22.5 Kcal/mole was calculated indicating a chemically-controlled process. The reaction was also sensitive to the concentration of oxygen in the system. The zinc required was considerably in excess of stoichiometry, possibly due to the dissolution and redeposition of lead: In general, the results were encouraging and demonstrated that lead impurities could be removed from D2EHPA using cementation type reactions.

Jan 1, 1995

By Gregory A. Knapp

Treatment of industrial wastewaters generally advances with specific chemical concentration and mass-flow targets, established by National Pollutant Discharge Elimination System (NPDES) permits. Treated discharges must also address toxicity to test and receiving water organisms. Various parameters might need consideration during treatment design and planning, such as the known toxicants, hardness, alkalinity, solids, nutrients, metals in both the dissolved and particulate state, and even flow. Since toxicity is used as a "catch all" regulatory monitoring tool, design of treatment systems should focus on the various factors contributing to toxicity.

Jan 1, 1996

A study was undertaken to remove the Se from waste solutions using a raw form of the biomass called Iota Chips derived from the seaweed, Eucheuma spinosum. Removal of Se from solutions was investigated as a function of time, pH, conc. of Se in solution (0.1 to 100 ppm) and lota Chips to liquid ratios of 10-2 to 10-5. For solutions containing initial conc. of 0.1 ppm Se, with the addition of Iota Chips at a solid to liquid ratio of 10-3, the Se conc. decreased to 0.03 ppm in about 3 hours. Iota Chips absorption capacity to the Se and its application to the treatment of the metallurgical processing effluents are discussed.

Jan 1, 1992