Search Documents

By José R. de Tenorio

The aim of the present work was to investigate the reduction process of MnO~FeO-Si02 slags by carbon-saturated liquid iron. The effect of the initial Mn content in the bath was explored. The initial Mn content was in the range of 0 up to 40 wt. %. The MnO content in the slag was kept constant at 40 wt. %. Tests were performed in laboratory apparatus. Samples of slags and bath were taken. In the first 5 minutes, it was observed a very strong reduction of FeO. This first step promoted a MnO-Si02 enrichment of the slag and a formation of CO bubbles, which increases the slag level. The increase ofMn content decreases the MnO reduction rate.

Jan 1, 1996

By He De-wen

The influence of wastewater containing benzene from chemical industry by technology combined blow-off with Fenton reagent oxidation was experimentally studied. The present results suggest that the technology combined blow-off with Fenton reagent oxidation can effectively remove benzene pollutant in wastewater. The main factors that influence the removal benzene such as temperature and blowing time and volume, pH and reagent dosage of H2O2 and Fe2+ are studied and the optimal experimental conditions are as follows: time 20min, temperature 40i, air-blowing volume 0.4L/min, pH value 5, and H2O2 and Fe2+ dosage 2mL/L and 200mg/L respectively. Under the above conditions, benzene pollutant can be removed up to 97%. Compared to other removal ways of wastewater containing benzene, the technology combined blow-off with Fenton reagent oxidation is more effective and has the advantage of high speed.

Jan 1, 2009

By He De-wen

Based on the principle of life cycle assessment (LCA), municipal solid waste management (MSWM) was analyzed by life cycle inventory method. According to the system expansion and substitution method, the content and frame of life cycle analysis is summarized and applied to municipal solid waste. On the basic of feasibility research of life cycle analysis on MSWM, the paper put forwards complete and concrete ?three changes? measures under life cycle analysis on MSWM. Some aims of MSWM can be achieved under above conditions of LCA on MSWM: to improve the current system efficiency of MSWM; to enhance the serve quality of MSWM, to increase recycle garbage from MSW; to reduce waste amount and reach minimization and innocuity aim of MSWM; to help the departments of MSWM to get over all difficulties to realize their ideal goals.

Jan 1, 2009

By Slobodan Radosavljevic

The polymetallic W-Pb-Bi-Ag ore from the ?Nova jama? ore zone of the Rudnik ore field have been investigated. Contact-pneumatolytic (skarn), pneumatolytic-hydrothermal, and hydrothermal mineralization phases are defined in this ore zone. The most significant mineralization phase that gave compact ore bodies is pneumatolytic-hydrothermal phase. A relatively pure Mo-free scheelite is the only tungsten-bearing mineral. Lead minerals are mostly presented by Pb-Bi sulphosalts and much less with galena. The image analysis coupled with Energy Dispersive Spectrometry (EDS) analysis on a Scanning Electron Microscope (SEM) was applied to the characterization of a W-Pb-Bi-Ag ore as an efficient tool for mineral quantification. Results of EDS (Energy Dispersive Spectrometry) analyses gave the empirical formulae: Pb1.91Ag0.05Cu0.08Bi1.93S5 for cosalite, Pb0.98Ag0.03Cu0.05Bi1.99S4 for galenobismutite and galena Pb0.99Ag0.03S.

Jan 1, 2006

By Zhigang Liang

A carbon free precast block was prepared by using high-alumina fused corundum as aggregate and fused magnesia, and ultra-fine Al2O3 and ultra-fine SiO2 powders as matrix materials. A small linear expansion for the precast block was achieved through spinel formation from the reaction of MgO with Al2O3. The precast block showed a lower apparent porosity, higher hot modulus of rupture and better slag corrosion resistance compared to the traditional Al2O3-MgO-C brick. Moreover, the practical application of the precast block to the ladle lining proved it to possess a better thermal insulation which could effectively prevent the temperature drop of molten steel during the refining process. It can be predicted that the carbon free precast block could possibly be accepted as a new type of ladle lining material for the production of low-carbon and ultra-low-carbon steel.

Jan 1, 2009

By P. J. Mackey

New and emerging, as well as proven technologies for the smelting of copper, nickel, lead and zinc are briefly reviewed. The number of new technologies available today is greater than at any time in the past, and interest and development activities remain high despite the economic dif-ficulties faced by the non-ferrous metallurgical industry. Part of the impetus is provided by the realization that only the most cost effective producers will remain competitive, and that new technology is one key to cost effectiveness. The commercially proven "new" copper smelting processes can now be considered to be conventional- technology, and are expected to dominate copper smelting for acme time. There is a growing. interest in continuous copper converting, although direct smelting and converting to copper in one vessel remains the- ideal. There is little activity in nickel smelting. After many years. of development, it appears that several new direct lead smelting processes will soon be a commercial reality. The electrolytic zinc process is expected to continue its dominance, although there is a renewed interest in pyrometallurgical approaches. One of the new zinc processes, and a molybdenum smelting process, illustrate the possibilities of using plasma technology in non-ferrous metallurgy. In the area of complex sulphides, there is perhaps less interest in the treatment of bulk con¬centrate, and more in the treatment of so-called dirty copper concentrates. Much of the technology ancillary to smelting has remained relatively unchanged, and more effort must be made to advance the technology in areas such as materials handling, gas cleaning and sulphur fixation, and energy recovery. More attention to engineering design is also needed. Escalating capital costs may make mini-smelters attractive, but imaginative technology and innovative engineering will be required to make them cost effective. Finally, a glimpse is offered of the smelter of the future.

Jan 1, 1983

By Denise Crocce Romano Espinosa

The recycling of waste of electric and electronic equipment (WEEE) is one of the main modern challenges. Among the variety of WEEE, batteries can be set apart due to their composition and their growing demand along with portable devices. The objective of this work is to characterize the thermal behavior of a sample of mixed types of batteries using a thermobalance (TGA). The results of tests showed that Cd evaporated up to 800ºC, Zn evaporation occurred mainly above 900ºC and manganese oxides were pre-reduced to MnO at temperatures above 900ºC.

Jan 1, 2009

By Xuemei Zheng, Aiyuan Ma, Chao Liu, Guojiang Li, Chenyu Sun, Jinhui Peng, Libo Zhang, Yongguang Luo

In this paper, the removal of fluorides and chlorides from blast furnace dusts by water vapor enhanced microwave roasting was investigated, combined with the advantages of microwave selective heating and based on a thermodynamic analysis of zinc and lead halides. According to proposed reactions in the process, detailed experiments were systematically conducted to study the effect of roasting temperature, holding time, air flow, water vapor flow rates, and stirring speed on the efficiency of the removal of F and Cl. The results show that 97.26% of F and 64.23% of Cl could be separated when the condition of the roasting temperature of 650°C, stirring speed of 80 rpm, holding time at 60 min, air flow of 350 L/h and water vapor flow rate of 8 mL/min was optimized.

Jan 1, 2016

By Jan Vrestal, Josef Tomiska, Pavel Broz

"Thermodynamic investigations on fcc solid ternary Fe-Ni-Cr alloys have been performed by means of the computer-aided Knudsen cell mass spectrometry. Ternary T.AP.-series (Thermodynamically adapted power series) are used for the algebraic representation of the thermodynamic excess properties. At 1650 K the molar excess Gibbs energy GE is negative over the whole field of stable fcc phase. The molar heat of mixing HE is exothermic in the predominant part of the fcc phase field. Only between the section with a constant ratio of mole fraction Xcr/XNi = 0.64 and the fcc phase field boundary the HE values are slightly endothermic. The results of this work can be used successfully for phase diagram calculations.IntroductionThermodynamic investigations on multicomponent alloy systems such as the Fe-Ni-Cr ternary system including the three binary boundary systems are very time-wasting and usually beset with considerable experimental difficulties. Additionally, the required experimental equipment is very expansive and the obtained results are not always satistying. Therefore it is understandable that many phase diagram calculations are based only on few experimental values of the molar excess free Gibbs energy GE. Consequently, Kundrat and Elliott [1] as well as Hillert and Qiu [2] used in their reassessments of the phase diagram of the Fe-Ni-Cr system thermodynamic data mainly assumed and/or optimized by means of various reasoning.Lee [3] reported recently, a revision of the used thermodynamic description of the Fe-Ni liquid phase is necessary to obtain a better agreement with the experimental data on the bcc/liquid or fcc/liquid tie lines and liquidus temperatures in the Fe-rich region of the Fe-Ni-Cr ternary system than in the previous assessments. This is 'in full agreement with mass spectrometric investigations of Fe-Ni alloys in the liquid and in the fcc solid phase, published earlier [4,5]. Indeed, phase diagram calculations based upon the molar excess free Gibbs energies GE obtained in these studies yield liquidus and solidus lines in excellent agreement with experimental phase diagram data [5]. Nevertheless, these experimental data have not been considered later on any more, not even in the revision by Lee [3]."

Jan 1, 1996

By Zhi-xiang Cui

Effects of flux, vulcanizing agent and reductant on slag cleaning in new-type slag cleaning furnace (Φ3.6 × 8.1 m) were investigated under the conditions including smelting temperature of 1200 and 1250 °C, settling time of 30 and 60 min, and Fe/SiO2 of 1.7–1.9. The results show that addition of SiO2, B2O3 or CaF2 into original copper smelting slag can improve settling separation effect. Though no effect on copper recovery, addition of FeS can provide heat required by reaction with oxygen and reduce copper dissolution in spinel phase and slag. Copper content in discarded slag can be controlled at 0.26% under the optimum comprehensive conditions with ratio of oxygen to natural gas of 1.6.

By Asmo Vartiainen

Background of Direct-to-Blister Flash Smelting is discussed; especially slag chemistry relating to copper solubility, slag fluidity and impurity behavior. In December, 2000, Mini-pilot Flash Smelting test runs were carried out at Outokumpu Research Oy to produce blister copper from Chilean concentrate and white metal and from a mixture of them. Tested slag types were iron silicate slag, ferrous calcium silicate slag and calcium ferrite slag with different slag compositions and different concentrate/white metal ratios. The test runs were successful. The fluxing effect of copper oxide was clearly demonstrated and ferrous calcium silicate slags remained fluid on a very wide liquidus range. The distribution of arsenic between ferrous calcium silicate slag and blister copper is much higher than between iron silicate slag and blister copper. This successful test run with the new slag type offer new possibilities in Direct-to-Blister process design.

Jan 1, 2003

By Brian P. Atkin

The NISOMI-81 opaque mineral searcil and identification system uses quantitative color values (Pe, dA, y) and VHN as its determinative para-meters. The system is designed to operate on a Radio-Shack TRS-80 micro-computer which is interfaced to a motorised diffraction grating mono-chromator (WILSCAN). Using an interfaced monochromator/photometer combination a typical identification including the measurement of the photometer data on both specimen and standard, calculation of color values and a computer search takes about 6 minutes. The data file contains 240 minerals at present but can easily be expanded as reliable new data become available.

Jan 1, 1982

By Hong-ying Xia, Bao-bao Wang, Jin-hui Peng, Bing-guo Liu, Li-bo Zhang, Zhi-qiang Li

Based on optimization using response surface methodology designed by Box- Behnken, to study the interaction of wet industrial salt with moisture drying temperature (50-90 ); duration (10-50s); and the weight of the materials (20-60g). The results show that: the experimental parameter conforms to the quadratic equation model to influence the moisture content and the dehydration speed., in analyzing the significance and the interaction of various factors, the optimum by the Design Expert software conditions for drying with microwave radiation include temperature of 90 , duration of 10s, and sample mass of 26g. Verified by experiment, the moisture content after drying is less than 0.25% and the dehydration rate reached 1.37g/min, between the predicted value and the actual value confirmed good fitting degree.

Jan 1, 2015

By Yuanbo Zhang

Zinc leach residues produced by hydrometallurgical zinc plants contain many valuable elements (zinc, iron, lead, gallium, indium silver, etc), while they have not been utilized effectively hitherto. In this paper, a new process of flotation-reduction roasting-magnetic separation to recover these valuable elements from zinc leach residues is developed on a basis of mineralogy investigations of them. The results show that silver concentrate with grade of 4321.6 g/t and recovery of 80.69% have been obtained, using 1750 g/t Na2S as conditioner, 750 g/t ammonium dibutyl dithiophosphate and SN-9 (assistant collector) as combined collector and 100 g/t terpenic oil as frother, if zinc leach residues with 523 g/t silver are floated at pH = 5.0. When the flotation tailings are subjected to reduction roasting at 1100? for 2 h, the volatilizations of zinc, lead and indium are over 96%. After roasted products are treated by wet-grinding and magnetic separation, the grade of gallium and gallium in the concentrates achieved respectively reaches 1805 g/t and 1536g/t, and the recovery of them is high to 94.67% and 93.20%, respectively.

Jan 1, 2006

By He De-wen

The municipal solid waste is a by-product of the daily life of urban residents. The quantity and ingredients of municipal solid waste has exceeded the current management and disposal ability, which has done a great harm to municipal environment and sanitation quality and threatened people?s health. On the basic of analysis on the amounts and main elements of municipal solid waste of Changsha City, the sanitation landfill, incineration, composting, reclamation and utilization technology of household waste were compared specifically in this paper. Based on the concrete conditions of Changsha City, the paper has proposed a disposal proposal combined with reclamation and landfill of municipal solid waste of Changsha City, and the environmental benefit, social benefit and economical benefit of the prepared processing routes were also analyzed in the paper.

Jan 1, 2009

By Pratheesh George

Solid state galvanic cell with CaF2 as the electrolyte was employed for determining the thermodynamic properties of Nb-Al binary alloys in the temperature range of 973-1073 K. The activities and activity coefficients of Al in NbAl3 were determined. The experimental procedure and the design and construction of the experimental setup have been also explained in detail. Aluminum activity in NbAl3 increased with increase in temperature and shows a strong negative deviation from ideality. The activities of aluminum in NbAl3 were determined to be 0.0165 and 0.0289 at 973 and 1073 K respectively. The stability of NbAl3 has been compared with other available intermetallic systems.

Jan 1, 2006

By Yunnen Chen

The test and use of natural materials as biosorbents for the removal of heavy metals from industrial wastewater is under constant development. In the present study, the biosorption capacity of waste microzyme was studied for cadmium The cadmium removal study has been carried out batchwise where the influence of physico-chemical key parameters such as pH value of solution, contacting time and initial cadmium ions concentration have been considered. The influence of metal ion concentration was evaluated and the results were fitted using adsorption isotherm models. The kinetic of cadmium biosorption was also investigated. The maximum percent removal was attained at the pH 7.0 after about 30 min. Waste microzyme was a potential biosorbent for the removal of Cd(II) from the effluent of electroplating industry.

Jan 1, 2009

By Zbigniew Zurecki

The selection of atmosphere composition is critical for controlling surface quality of reactive aluminum alloys during solution treatments. An improper selection of annealing atmosphere can result in surface blistering in AI-Mg and sub-surface depletion of lithium in AI-U ingots. To determine optimum atmosphere compositions for homogenizing A1-Mg and Al-Li alloys, Ii number of exploratory experiments were carried out in air, nitrogen, and carbon dioxide based atmospheres including reactive impurities or additive such as moisture and sulfur hexafluoride. This paper describes the influence of these atmospheres on high-temperature oxidation and sub-surface defects. The results are discussed in terms of the change in Pilling-Bedworth ratio.

Jan 1, 1996

By Dachun Liu, Baoqiang Xu, Bin Yang, Yong Deng, Heng Xiong, Xiumin Chen

"In this paper, vacuum distillation technology has been employed to study the possibility and regularity of separating copper and enriching lead, silver and other valuable metals from copper- based multi component alloys. The result of experiment indicated the practicability of vacuum distillation dealing with copper base complex multi-component alloy to separating lead and silver, when the vacuum distillation temperature was 1637K, distillation time was 60min; residual gas pressure was 20-30Pa, the removal rate of silver was 95.86%, of lead was 99.63%; the evaporation rate of copper was 0.745%. The removal rate of arsenic, antimony and tin respectively were 83.09%, 48.12% and 24.54%. Vacuum distillation method is applicable for dealing with the copper-based multi component alloys, silver and lead can realize effective recovery.IntroductionCopper generally go with lead mineral, therefore, to remove copper from lead becomes an inevitable link in lead smelting. Dross from removed copper usually contains lead, arsenic, antimony, tin and noble metal silver. In abroad, soda ash-iron dust is adopted to process copper dross of this kind. The outcomes of this process are lead matte, wet lead, scoria smoke dust etc[1~5] The dominant components of all the outcomes are copper and lead. Moreover, in the process of tin smelting, copper contained by-products are produced, such as, crude tin alloy, tin lead electrolytic anode slime and so on. Copper content of all the products are ranging from few percentages to several tens percentage. Those products, no matter merge into main producing process, or separate treatment cost losses of valuable metal. For one hand, the containing of copper of outcomes from pyrogenic attack is less than 50%, for the other hand, a lot of valuable metal need to be processed, which increase the cost of retrieve."

Jan 1, 2013

By B. B. Agrawal

Iron ore fines is an area of concern in India. A possible avenue is to use these fines for sponge ironmaking. Work has been carried out to pelletize these fines with coal and a suitable binder, and cure them in ambient atmosphere to retain in-situ reductant. Pellets were characterized for physical strength and metallisation. Critical factors were granulometry was percentage of coal & binder. In laboratory tests, pellets got metallized faster compared to lump ore. Large-scale trials were conducted in a 12-meter long rotary kiln plant. For 90% metallization, required residence time was only 60 minutes against 240 minutes for lump ore. Coal requirement also decreased. Investigations established the fast reduction nature of pellets. This is due to reduction-reactions occurring simultaneously at many sited within the composite pellets, in addition to the diffusion of reducing gases from the surface of the pellets to its core. The developed process is a value addition in the conventional pelletmaking and is environment-friendly also.

Jan 1, 2006