Search Documents

By Bengt L. Stillborg

INTRODUCTION This paper summarizes the result of a two and a half year research program. The objective of the research was to develop a fundamental understanding of the Rib-in-Roc method. Through the development of a new model technology, namely three-dimensional physical models which powerfully exploit the results of dimensional analysis Stillborg, Stephansson and Swan (1), it has been possible to establish the contribution to both permanent and immediate stabilization of a large underground opening pre-reinforced by the Rib-in-Roc method. Using the results from these physical models and earlier work by Stillborg and Stephansson (2) and Åkesson (3), a conceptual synthesis is given in this paper so demonstrating the Rib-in-Roc method to be a practical working system of pre-reinforcement. DESCRIPTION OF THE RIB-IN-ROC METHOD To give the reader an idea of how this method of pre-reinforcement is performed, a short description will be given, Figure 1. Before any full-scale excavation takes place an entry is made in the host rock and rib raises are driven around the proposed opening. These raises are made at a spacing that is dependent upon rock quality; an opening in poor rock needs more ribs per length of opening. As the ribs are driven they are used as a site from which very competent rock bolting can be done. As a rib is excavated it is filled with reinforced concrete. Finally after having in this way reinforced the zone around the proposed opening, (a reinforced arch is formed) the displacements are automatically controlled as the opening is being excavated. Using this method openings with a span of 50-60 meters (160-200 ft) and a height of 60-80 meters (200-260 ft) are likely to be realised.

Jan 1, 1979

By H. H. Einstein

This paper reviews how uncertainty has been dealt with over the past 40 years using the decision making cycle as a frame of reference. The review of the phases of this cycle, as applied to rockmechanics and rock engineering, namely characterization, performance analysis, updating and decision making shows that in each, progress has been made over the past 40 years, although most of the basic concepts existed already in the 1960’s. Characterization is the area in which the greatest scientific steps were taken, this phase and performance analysis also gained from the tremendously expanded computational capabilities which allow one to use both more complex and more practically oriented models. The greatest practical advance is without using any doubt in risk based decision making although its acceptance shows interesting differences between different professions. Dans l’article suivant on utilise le cycle de décision pour illustrer le développement du traitement des incertitudes en mécanique des roches et en construction en roche dans les quarante années passées. La revue des phases du cycle de décision montre qu’on a fait du progrès dans chaque phase du cycle de décision, c’est à dire dans la caractérisation, dans l’analyse et la prédiction du comportement, dans l’actualisation et dans l’acte de décision, même si les concepts fondamentaux existaient déjà dans les années 1960. Les plus grands avancements scientifiques se trouvent dans le domaine de la caractérisation tandis que l’analyse prédictive profitait du développement de l’informatique qui a mené à des modèles plus complexes mais aussi plus pratiques. Le plus grand progrès est sans doute dans le domaine de l’acte de décision sur la base des risques. Ce procédé est devenu assez commun même s’il y a encore des différences d’acceptation entre différentes professions. Im vorliegenden Artikel wird der Entscheidungszyklus gebraucht, um darzustellen wie sich derUmgang mit Unsicherheiten im Felsbau während der letzen 40 Jahre entwickelt hat. DerÜberblick über die Phasen des Entscheidungsprozesses zeigt, dass bei der Anwendung in derFelsmechanik und im Felsbau, in allen Phasen d.h. bei der Charakterisierung, bei der analytischenVorhersage, beim Aktualisieren und bei der Entscheidungsfindung Fortschritte gemacht wurden,obwohl die grundlegenden Konzepte bereits in den 1960er Jahren existierten. Im Gebiet derCharakterisierung gab es wohl die grössten wissenschaftlichen Entwicklungen, während dieanalytische Vorhersage vor allem von den Fortschritten der Informatik profitierte, welchekomplexere wie auch praktischere Modelle möglich machte. Der grösste Fortschritt ist ganz sicherin der Entscheidungsfindung zu beobachten, wo Risikobetrachtungen gang und gäbe sind, obwohlhier noch einige Unterschiede zwischen verschiedenen Berufsgattungen zu finden sind.

Jan 1, 2003

By Gerald W. Longenecker

For decades, traditional hydraulic engineering approaches have been used for sizing stream channels when stream relocation efforts have been necessary to allow for the advancement of quarry and other surface mining operations. These approaches have been based on various ydraulic models to design channel cross sections and slopes that could pass the required regulatory design storm such as the 2-, 5, lo-, 25-, 50-, or even loo-year events. Designing the stream channel to handle these more extreme ,storm events would often lead to large channel designs which required extensive bank and channel bottom stabilization techniques including concrete, rip rap, gabions, or other expensive approaches. The constructed channels often required ongoing maintenance to remove accumulated sediment and other debris which would settle out and reduce the hydraulic capacity of the channel.

Jan 1, 1998

By Donald W. Baggs

This report describes economic mining feasibility studies conducted by the Bureau of Mines to estimate mining costs in the Porcupine mining area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of three mineral deposit types: 1) massive sulfide deposits containing zinc, copper, and silver, 2) vein gold, and 3)disseminated gold. Cost estimates were developed using the Bureau of mines Cost Estimating S,-stem. Discounted cash flow rates of return were calculated using the Bureau of Mines MINSIM (mining simulation) computer program. Three sets of metal prices were used in the study based on recent historical price information. Underground longhole stope mining of a massive sulfide deposit containing 25 pct zinc. 1 pct copper, and 63.6 g/mt silver was found to be economic at high metal prices at a quantity of 13,200,000 mt ore. Cut-and-fill mining of a 26,400,000 mt massive sulfide deposit was found to be economic at medium metal prices. Open pit mining of a similar deposit was found to he economic at medium metal prices and 26,400,000 mt ore, or at high metal prices and 6,600,000 mt ore. Underground mining of a vein gold deposit was found to be economic at a grade of 17.1 g/mt medium metal prices and 1,320,000 mt ore. Open pit mining of a disseminated gold deposit was found to be economic at a grade of 1.71 g/mt medium metal prices and a quantity of 39,600,000 mt ore.

Jan 1, 1986

Radioisotope x-ray methods for the on-stream determination of copper, lead, and zinc in mineral product slurries were developed, and were successfully tested at the plant of Cobar Mines Pty. Ltd.The tests were made in three stages. Measurements to determine the precision of analysis were made initially on briquettes of the mineral products. The effect of slurry solids content variations was then determined by measurements on the mineral products in a recirculating slurry loop. The radioisotope analyser was finally tested in a series of on-stream measurements in the plant.Copper, lead, and zinc in flotation feed and in copper concentrate were determined to a precision ranging between 1·4 and 15 per cent of the mean element concentration in the slurry solids. These precisions are within limits required for plant control purposes at Cobar.

Jan 1, 1971

By Michael Kelly

Inertial navigation technology has, for the first time, allowed the position of a longwall shearer to be mapped in three dimensions. Following the success of the technology in highwall mining and successful trials on a longwall face, the Australian Coal Association Research Program (ACARP) commissioned a three year "Landmark" project that aimed to advance longwall automation to the level of "on-face observation" by the end of 2004. This project has been completed with the following successful technical outcomes: Automatic face alignment was achieved, using an inertial navigation-based sensor on the shearer, to accurately measure face geometry and feedback signals used to move OEM (Original Equipment Manufacturer) roof supports. Operational on-line measurement of creep with creep information incorporated into face alignment corrections. Inertial Navigation System (INS)-based enhanced horizon control was bench-tested. Operational broadband communications system to shearer using wireless Ethernet on a commercial-product basis. Acquisition of located coal-face features for use in thermal infrared-based horizon control. Automated Longwall Information System (LIS) developed which integrates information from multiple systems and sensors and provides high quality visualisation and control interfaces. Automatic roadway and face convergence monitoring tools successfully tested. Condition monitoring tools developed and demonstrated for improved face reliability. This paper summarises the outcomes of the project and describes the work being undertaken for the 2 year Landmark Extension project approved in April 2005. Consistent with the conference theme, the paper focuses on the ground control aspects of the project.

Jan 1, 2005

By J S. Dunlop

At its most basic level, minerals project management may be broken down into a series of logical chronological phases, described in this paper as: exploration, discovery; scoping and pre-feasibility; feasibility and approval; project financing and commissioning; operation; expansion and closure. Each phase has its own peculiarities and challenges, any one of which can potentially upset the forward progress of a minerals project.Reference is made to each of these project phases based on the authorÆs many years of first-hand experience, in an attempt to identify issues within the project management spectrum where additional caution may be warranted. Left un-addressed, these issues can cause undue delays in the project timeline, ultimately delaying approval at significant project cost.Finally, reference is made to the Mine ManagerÆs Handbook recently published by the AusIMM which is an excellent project management resource, considered to be very relevant for minerals treatment plant managers, whether the context be constructing, operating, expanding or shutting down.CITATION:Dunlop, J S, 2013. Mineral project management - A perspective from four decades in the industry, in Proceedings MetPlant 2013 , pp 13-27 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Luis Alva Saldaña

El presente artículo describe la posibilidad de de la utilización de carbones de baja\ ley, así como arcillas carbonosas ricas en alúmina, en la fabricación de un fertilizante barato a base de nitruro de aluminio para servir a la reforma agraria peruana.

May 1, 1967

By George K. Clement

Manual estimating method through use of equations, factors and curves for preparation of feasibility type estimates for capital and operating cost of mining and primary beneficiation in the United States and Canada of various types of minerals occurrences, except fossil fuels, using state-of-the-art technology. User should have basic estimating experience in the mining industry and/or related fields. Primary usage of this handbook will be for the preparation of preliminary estimate within a reasonable degree of accuracy with relative small amounts of hard input data. Output may be used to determine if a more finite type of estimate should be produced.

Jan 1, 1978

By J Belke

Murrin Murrin Operations have not had a successful beginning. Numerous reliability and operability issues, many of which are the result of design decisions, have been addressed through mechanical and operational changes and the CCD circuit is no exception. Four design aspects of the CCD circuit that have caused and continue to cause operational problems are: the inclusion of solution neutralisation gypsum in the CCD circuit feed which was designed solely for HPAL residue without proper investigation of its impact on the achievable underflow density and resulting wash efficiency; the decision to construct the thickener base from thickened solids; the lack of redundancy in the overflow, underflow and tailings pipe work; and the lack of thickener operational flexibility in the central rake-lift and feedwell dilution system. In November 2002, the lack of operational flexibility in the rake-lift and the feedwell dilution system was improved through mechanical modification as follows:CCD1 rake mechanism was modified to allow central vertical lift of 600 mm; and CCD1 changed to forced dilution using the Outokumpu TurbodilRântechnology by replacing the E-DucânRtechnology of Eimco. The installation and the results of the CCD1 rake-lift mechanism and feedwell dilution system changes are discussed in this paper.

Jan 1, 2004

By Remo Grandori

The Umiray Angat 13,2 km long tunnel in Philippines have been bored through extremely variable and difficult ground conditions including a number of special events. In particular the following adverse conditions were found: faults in decomposed ground, high temperature rocks, extremely rapid and important convergence phenomena, water inflows up to 800 litres per second. The special El Nino climatic conditions caused a long dry season and lower the level of the lake that was granting the access by barge to the site under the minimum navigable level. Many equipment have had therefore to be transported to site by a 10 ton capacity helicopter, after having been partially dismounted. For the same reason most of the tunnel drive have been bored servicing the site by 1 ton capacity helicopters to transport materials, spares and personnel. In order to overcome the above geological and logistic problems several innovation were introduced and tested in this project. Despite all that difficulties the 13,2 km of tunnel were bored in about 24 months, with a global average of 500 m/month.

Jan 1, 2001

By Ian Misich

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialed the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, site specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tills, and strains for rectangular panels and describe the sequences of ground movement from the mine root through to the ground surface. The fact that both subsurface and surface subsidence characteristics have tied in well, gives greater confidence for predictions made from these models

Jan 1, 1992

B. P. Thomson (South Aust. Dept. of Mines): Dr. A. B. Edwards presents in the published discussion on the above paper, his interpretation of the dolerite dyke-lode relationship as a major objection to the syngenetic origin for Broken Hill ore bodies to which Mr. Condon subscribes.Dr. Edwards claims that the dyke-lode relationships indicate clearly that the Broken Hill orebody was formed after the folding and regional metamorphism of the Willyama Series. Field evidence compels m:e to join with H. F. King (1958), in finding this conclusion unacceptable-as follows:(1) Broken Hill type mineralization, as defined by King and Thomson (1953), is clearly confined by the regional sillimanite isograd and does not extend into the lower temperature almandine and biotite zones as does the Thackaringa type mineralization.(2) In the Corruga area the writer has mapped a dolerite dyke apparently cutting a conformable quartz gahnite lode of the Broken Hill type (see Edwards 1958, p. 12).(3) At the Champion mine a similar lode is cut by a fine grained granite dyke.An alternative history of the dolerite dykes to that given by Stillwell & Edwards (1956, p. 26) appears possible. It has been suggested by the writer in an unpublished thesis, (Thomson 1955, p. 30), that the pyroxenite and serpentine plugs and dolerite dykes are rheomorphic end-products of a complex regional metamorphic and metasomatic process involving the formation of amphibolite and pegmatite. The analogy in composition between the dolerite and normal amphibolite is close (see Edwards 1958, Fig. 1, p. 22).

Jan 1, 1959

By Rudolf E. Greuer

This study concerns itself with two topics of the mine ventilation - mine fire interface which, when the work for this study began, did not seem to receive sufficient attention. Section 1: Comments on Spontaneous Combustion of Coal in Mines It is attempted to describe heat generation, heat and oxygen transport, in such a way that existing experimental data for U.S. coals can be used to assess conditions inducive to spontaneous heatings quantitatively. Investigated are, in particular, critical air velocities, minimum sizes of coal accumulations, moisture contents and the influence of mining factors. An extensive, practice oriented literature survey is included. Section 2: The Early Detection of Mine Fires by Assessment. of Mine Gases The suitability of the major constituents of combustion products for an early detection of fires is discussed. The same is done for gas concentration ratios. Since it was felt (at least at the time when this report section was written) that the value of the carbon monoxide/oxygen deficiency ratio was overestimated, the usefulness of monitoring this ratio as compared to monitoring CO concentrations was critically investigated. The state of art concerning instrumentation and organization of fire detection systems is reviewed also.

Jan 1, 2011

By P. K. Narasimharaghavan

The major threat to the sustainability of Aluminium Industry is its significant contribution to global warming by way of generation of non eco-friendly gases during its production cycle from Bauxite to the finished product. Though reduction measures are taken in control and effective recovery of values from pot room gases, efforts in use of environment friendly additives in the final products production line is warranted. In this line, the present paper describes our efforts in the use of a new generation refining flux which apart from helping in effective removal of alkali metals, reduction in inclusions and ensure a better metal cleanliness shall also aide in reduction of obnoxious gases generated during the metal refining process prior to casting. The aim of the current work was to reconcile the practical results with the old generation fluxes used. Further improvements to bring in a better metal cleanliness will also be discussed.

Jan 1, 2010

The term geochemistry - chcmbtry' of the earth - is almost limitless in its implied subject, but of recent years a major trend of research in this field has been towards economic application in the search for mineral deposits, and in particular for those of some ofthe less common elements for which a demand now exists.Geochemistry is in a state of slow transition from a purely descriptive subject to a fundamental science concerned with the relationships that exist between the distribution of the elements in the earth's crust and the physical characteristics of the atoms of those elements. The progress achieved promises a set of basic principles which will relate the atomic characteristics of an element to the physico-chemical conditions that make for its dispersion or concentration. This means that, given a geological map of an areasufficiently detailed for the physico-chemical conditions existing in past geological eras to be deduced, there is the possibility that the relative distribution throughout that area of any element present, and its likely mode of occurrence, could be predicted from a consideration of its atomic characteristics.Since the atomic characteristics of the elements are becoming increasingly well defined by physical research, the attainment of this ideal of prediction depends upon:(a) the strengthening of geochemical theory; and(b) the development of petrological and mineralogical methods of assessing the conditions of temperature and pressure prevailing in geological formations at various stages in their history.The other prime requirement is a d.etailed geological map - a requirement that is all too often lacking.The fact that there has been very little "geochemical approach" to problems of economic geology in Australia should not be taken to mean that there is little point in trying to develop such an approach here in as active and as rigidly scientific a manner as possible. The degree of success that has attended the attempts so far made, to which reference is made below, suggests the reverse, particularly in view of the relatively slight cost involved if the investigations were properly organised on a centralised basis. There are three aspects of geochemistry that are directly applicable to the search for economic minerals.(a) The classic technique of the prospector can be made more sensitive and reliable by the use of modern equipment coupled with the application of geochemical theory to geological and structural data. The case of the rare alkali elements (see below) is givenhere as an illustration of the way in which the distribution of elements can be predicted from the first principles of geochemistry, thereby replacing the prospector's dependence on his "sixth sense" that enabled him to suggest that a certain area of formation was"favourable" for the occurrence of a certain type of mineral deposit.At its best, this sixth sense amounted to an almost subconscious correlation of all relevant associations and typical occurrences of the particular mineral experienced by the prospector during his...

Jan 1, 1950

By Mark P. Meyer

A mineral investigation of the Chugach National Forest, Alaska was conducted jointly by the U.S. Geological Survey and the U.S. Bureau of Mines from 1979 to 1983 as part of the RARE II program. The U. S. Geological Survey remapped the geology and distribution of mineral resources. The Bureau investigated mines, prospects, and mineral occurrences. Previously unreported mineralization in three areas, Long Bay, Wells Bay, and Miners River were discovered in the western portion of the SOUND study area. Copper, lead, zinc, gold, silver, nickel, cobalt, fluorite, and arsenic were found in north-northeast to north-northwest trending shear zones, veins, felsic dikes, and granitic intrusives in Tertiary Orca Group metasedimentary rocks.

Jan 1, 2011

By John Wilson

This report describes the performance of Phase I of a project to design, analyze, and demonstrate a multilift longwall mining method applicable to mining coal seams twelve (12) feet or more in thickness. A non-simultaneous multilift operation is the most viable thick seam mining technique for introduction to the United States coal industry. In the case of the proposed site at Emery, Utah it will result in an increase in coal extraction from 30% with present methods to at least 50% and possibly more. The major technological advance involved in this project is mining a lower lift under a previously mined upper lift. To accomplish this, entries must be developed and maintained beneath the upper lift gob. This will necessitate the use of steel supports at frequent intervals throughout the lower lift' entry system. This has not been done in the U.S. to date. An economic analysis of the project indicates that, while this method will result in a higher than average cost per ton for coal mined, the coal would be competitive with current-operation in the area.

Jan 1, 1976

By Winfried Rosenstock

The development of electronic initiation systems has partially reached or will reach in a short period of time full reliability for general use without limitations. Unfortunately those systems meet with a fully unprepared mining community and is confronted worldwide with blasting procedures which are not suitable to exploit the full range of the electronic option. This is for the time being only belonging to quarrying and general surface mining, for the use in underground operations the detonator is still not yet competitive, apart from special cases. It is not to be taken in doubts that the introduction for underground purposes will follow in a less shorter or longer period of time.

Jan 1, 2003

By S. M. Spottiswoode

Much as one hopes to predict whether damaging seismicity might occur somewhere in the next shift, this is not possible at present. Recently, an analysis of seismicity at two mines has shown that a small increase in seismicity occasionally occurs before both large and small events. This analysis is extended here to five mines, with the same results. Earthquake seismologists forecast hazard in terms of the average incidence of earthquakes over the last 50 years, adjusted on an hourly basis according to the possibility of aftershocks of events that have happened. The rate of seismicity in any area remains approximately constant when expressed as seismicity per area mined, or better still, per unit of elastic strain energy released. It is suggested that seismic hazard in mines be estimated using historical seismicity and forward modelling, adjusted according to the possibility of aftershocks. In summary, medium-term forecasting of seismicity is viable; short-term prediction of large events is not.

Jan 1, 2010