Search Documents

By H. LeChatelier, B. Bogitch

Page Introduction........................... 134 Methods of Investigation....................... 135 The Tridymite Network...................... 137 Independent Variables....................... 146 Manufacturing Operations..................... 153 Introduction Silica brick are indispensable in the manufacture of steel because they alone are able to withstand the high temperature of regenerative furnaces. All attempts to replace silica brick by other refractory materials for this purpose have failed, but the reason for this failure has remained obscure; we shall give an explanation later in this paper. Before the war, silica brick employed in France came principally from abroad, for which reason, since the beginning of hostilities, certain French steel works have been seriously handicapped. Our attention was first directed to the question by M. Bied, Engineer of the Teil Works. With him, we began certain investigations, at first using our laboratory and the furnaces of neighboring steel works. The larger part of our experiments, however, have been made in the laboratory of the Faculty of Sciences at the Sorbonne. For the heating of our samples, we are deeply obliged to MM. Charpy, Yeatmann and Guerineau. In undertaking these studies, our first aim has been to render assistance to French industry, by indicating, as precisely as possible, the necessary conditions for the manufacture of high-grade brick; but at the same time me have

Jan 1, 1919

By Leslie F. Tedsen, Alan E. Flanigan, John E. Dorn

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By Lawrence B. Wright

THE Republic district, Washington, is of new interest because of the discovery of new gold-silver ore within a unique structural pattern. The camp was revived in 1937 following installation of a plant to treat low-grade disseminated ore at Knob Hill and further stimulation followed discovery of "cross vein" breccia ores in 1939. Previous writers 1-2 ascribed the quartz veins to a latite porphyry stock, but are in disagreement as to its precise location and extent. This study leads to the conclusion that the ores have a more profound parentage linked to a broad system of thrust faults and folds, the mechanical origin of which is related to a southward trending (Sanpoil) syncline connecting with the Lewis and Clark zone of shift described by Billingsley and Locke3 in 1939. The Republic anticline and a cross anticline recumbent against Cretaceous granodiorite, and involving some 4000 ft of Eocene andesite flows and early Miocene lake beds, localize the ores, mainly along the east flank, in a series of openings simulating drag folds and steeper than the folded flows. These broad structural features no doubt reach deeply into the basement rocks, where at appropriate crossings and junctions it is suggested that heat effects gave rise to oremaking materials, including, in this instance, intrusive breccias that later were mineralized, and comprising the broader bodies of new ores. The breccia ore is seen crosscutting the earlier narrow quartz veins with a welding of the two at junction areas by a second surge of ore minerals. The ore mined and developed since 1937 equals district production from 1896 to 1937. The ores are typified by cherty quartz, adularia and some barite, with fine pyrite and marcasite, polybasite, pyrargyrite, tetrahedrite and gold. Selenium is present, possibly with gold, as a normal selenide. The disseminated ores, as well as the vein and breccia ores, are localized principally in one 500-ft flow (Knob Hill andesite), which has been traced around the crest of the low northward-plunging Republic anticline. The gold-silver ratio in the earlier narrow veins is about 1 to 4 and in the disseminated and breccia ores, 1 to 7. The latter higher silver ratio is deemed to reflect the character of the second surge of mineralization. Sills and dikes of the Columbia River (Miocene) basalt cut the folded structure and ore, thus placing the mineralization in the middle Miocene.

Jan 1, 1947

By Fred Bond

This paper is a continuation of two earlier papers,1,2 and presents new data on the grindability of various ores and other materials-the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a. new method of measuring the "surface energy" of in ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems.

Jan 1, 1938

By E. T. Turkdogan, L. S. Darken, R. J. Fruehan

Further consideration is given to the application of the quadratic formalism to evaluate the thermodynamics of binary metallic solutions from experimental data. The use of the thermodynamic relation, in(r1/r2) dN2= 0, in the evaluation of activity data is discussed. The empirical correlations derived previously for enthalpies and entropies of solutions in Part II are shown to be predicted theoretically for a special case. The applicability of the quadratic formalism to the activity coefficients for binary organic solutions is demonstrated. DARKEN&apos; introduced a quadratic formalism describing the composition dependence of the activity coefficient in the terminal regions of binary metallic solutions. In a subsequent paper (Part II) Turkdogan and Darkeen2 extended this formalism to the enthalpy and excess entropy of binary metallic solutions, and showed that the available data for the activity coefficients and heats of mixing of many solid and liquid binary metallic solutions confirm reasonable applicability of the quadratic formalism. Much variation was noted, however, in the extent of the terminal regions from one system to another, commonly from about 10 to 70 at. pct. For the present purpose, equations derived previously need be given only for one of the terminal regions, e.g. region (I), 0 < N2 < N&apos;2: where subscripts 1 and 2 indicate quantities for components 1 and 2 and superscript ° the values at infinite dilution; other terms are: N = atom fraction, y = activity coefficient, = partial molar enthalpy of solution, ?HM = molar heat of solution, ?Sx = excess partial molar entropy, ?Sx = excess molar entropy. The heat and entropy like terms (constants) el, and S12 are defined in the following expression for the temperature dependence of a12, thus a12 £12 — s12 rnl 2.303RT 2.303 R l J Using this formalism, the thermodynamics of binary systems in the terminal regions may be described over a temperature range of experisental interest in terms of eight quantities: Lº1—Lº2, ?Sx1,?Sxº2 , £12 ,£21,fiai, S12, and S21. In the previous paper, these quantities were evaluated for many solid and liquid binary solutions, and two significant correlations were observed between these thermodynamic quantities pertaining to the terminal regions, thus [10] and [11] Combining Eqs. [9], [l0], and [ll] and rearranging gives a12 -a21 = 1.382R log rº2- 0.08(?S2xº- ?S1xº) [12] Since the second term involving entropies is small and Eqs. 1101 and [ll] are empirical relations, the above equation may be simplified to a12 = 2.74 log rº2 [13] Using the values of a&apos;s and y°&apos;s compiled in Parts I and 11, a12 - a21 is plotted against log(rº2/rº1) in Fig. 1; the line drawn has a slope of 2.74. For Hg-K at 300°C, log(yº2 /yº1)= —5.10, not shown in Fig. 1, and from correlation [13], a12 - a21 = -13.97; this is to be compared with -10.76 derived from the activity data (Part II).

Jan 1, 1970

By A. P. Miller, T. S. Washburn

Improved procedure in the manufacture of rail steel has come as the rail user demanded better wearing qualities combined with greater unit weight. With each weight increase per lineal yard has come greater difficulty in making a product that would successfully withstand all tests that modern rails must meet. With these facts in mind, and with a sincere desire to produce a rail whose service in track would be satisfactory in all respects, the steelmaker was quick to realize that all of the factors entering into his process would have to be more closely controlled. Control of rail-steel slags was recognized as one of the most important of many interdepending factors. The object of slag control is to hold the slag compositions within a range that gives the best results with respect to economy of production, uniformity of analysis, and quality of the finished rails. The most important component of the slag from the standpoint of these production and quality factors is the ferrous oxide content. This component is a good indicator of the basicity and oxidizing power of the slag, and these largely govern the effect of the slag on the steel. Consequently, the

Jan 1, 1935

By J. D. Miller, A. Cortez, J. Hupka

The separation efficiency of the hot water digestion-flotation technique used for bitumen recovery from various domestic tar sands was evaluated. Bitumen viscosity was found to be the most important tar sand property in determining the success of the bitumen separation. Bitumen viscosity of the tar sand war controlled by changes in digestion temperature and/or changes in diluent (kerosene) addition. Complete and uniform dilution of the bitumen phase was achieved by providing a sufficient presoaking, or penetration time, for a given tar sand type. For all the tar sand samples tested, an excellent correlation was obtained between the coefficient of separation and the bitumen viscosity. To achieve a satisfactory coefficient of separation, it was found that the bitumen viscosity must be reduced below 1.5 Pa.s (16 P) at the temperature of digestion. This was the case regardless of the tar sand type, grade, or origin.

Jan 1, 1984

By Eric A. Nordhausen

A good deal of dialogue has been published and voiced concerning one mining regulation or another, that, according to those raising the issues, in effect shuts down or drastically reduces mine and/or mill reduction. The objective of this discussion is to there fore synthesize the various regulations affecting the uranium mining industry and attempt to realistically assess the extent of impact to yellowcake production - on both an individual and collective basis. Emphasis is placed on the later or newer permitting requirements under the Mill Tailings Act, Underground Injection Control Program, the Consolidated Permit Program, and the Resource Conservation and Recovery Act (RcRA).

Jan 1, 1980

By John Gross

THE deductions drawn in crushing and grinding operations have heretofore been based on a separation of the products into various sizes. A crushed product may be sized by sieving, by elutriation, and by aid of the microscope. To estimate the surface of each size the relation of the surface to the estimated average diameter must be assumed. Such a relation, owing to the irregularity of the particles, may involve two assumptions: First, a factor to convert average diameter to surface for one particular size; and second, a variation in the factor as the diameter of the particle changes. Obviously a surface measurement in which such assumptions and estimates are involved is questionable. In the first paper of this series1 a method has been given by which an accurate measure of surface of quartz can be obtained from its dissolution rate. By the use of this method, surface measurements have been made on a series of sieve sizes of crushed quartz, the results of which are given and discussed in this paper.

Jan 1, 1928

By W. A. Foster

NINETY years after the Riddle nickel deposit N was discovered in Oregon in 1864, Hanna Coal & Ore Corp. began mining operations. Until 1954 much prospecting and preliminary development work had been done on the property, but no ore had been shipped other than for metallurgical testing. The deposit is being explored by churn drilling and trenching, and a few test shafts have been put down for the purpose of studying the ore in place, determining volume and moisture factors, and gathering bulk samples for pilot plant and smelter tests. In churn drilling, 6-in. casing is driven down 2 or 3 ft behind the drill bit and bottomed at each 5-ft interval. All the sludge for each cased 5-ft interval is dumped through a splitter and one eighth is saved and analyzed. Drillholes are stopped after going through the ore zone and penetrating fresh peridotite in which the nickel content is less than 0.5 pct.

Jan 8, 1957

By A. P. Miller, T. S. Washburn

Improved procedure in the manufacture of rail steel has come as the rail user demanded better wearing qualities combined with greater unit weight. With each weight increase per lineal yard has come greater difficulty in making a product that would successfully withstand all tests that modern rails must meet. With these facts in mind, and with a sincere desire to produce a rail whose service in track would be satisfactory in all respects, the steelmaker was quick to realize that all of the factors entering into his process would have to be more closely controlled. Control of rail-steel slags was recognized as one of the most important of many interdepending factors. The object of slag control is to hold the slag compositions within a range that gives the best results with respect to economy of production, uniformity of analysis, and quality of the finished rails. The most important component of the slag from the standpoint of these production and quality factors is the ferrous oxide content. This component is a good indicator of the basicity and oxidizing power of the slag, and these largely govern the effect of the slag on the steel. Consequently, the

Jan 1, 1935

By Henry F. Hebley

This paper brings within the compass of one comparatively brief article a general description of the situation concerning the nation&apos;s water resources. It touches upon the phenomenal growth in the demand for water supply and emphasizes the problems facing the coal industry both with regard to acid mine water drainage discharged from active and abandoned mines and the suspended solids discharged to the stream system from wet coal preparation plants.

Jan 4, 1953

Jan 1, 1890

By Bunting S. Crocker

EBBLE grinding at Lake Shore is not a temporary BlE wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct — 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 11/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1-in. steel ball charge. To change pebble size it is necessary only to change two sets of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean out the customary supply of grinding balls kept on hand. Also it has not always been possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant, should be designed to use as many units or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, 2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant and an extremely efficient one. In this plant the ratio of ball mills to tube mills was 1:2. When the much cheaper pebble mills were substituted for the tube mills, this ratio was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on — 8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.&apos; This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without grate discharges both with 1-in. and -in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report2 was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are lengthy and may be covered in a separate report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The —8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands from the bowl sent to the primary pebble mills, see Fig. 1. In the pebble mill circuit the ore is ground to 90 pct —325 mesh (24 pct + 28 microns). In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO,, 80 pct insoluble. Its grindability at different meshes has been shown near the top of the list in F. C. Bond&apos;s grindability tests.&apos; Lake Shore is not shown, but an adjacent mine with identical ore, Wright-Hargreaves, is. Reasons for the Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1953

By Bunting S. Crocker

EBBLE grinding at Lake Shore is not a temporary BlE wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct — 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 11/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1-in. steel ball charge. To change pebble size it is necessary only to change two sets of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean out the customary supply of grinding balls kept on hand. Also it has not always been possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant, should be designed to use as many units or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, 2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant and an extremely efficient one. In this plant the ratio of ball mills to tube mills was 1:2. When the much cheaper pebble mills were substituted for the tube mills, this ratio was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on — 8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.&apos; This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without grate discharges both with 1-in. and -in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report2 was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are lengthy and may be covered in a separate report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The —8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands from the bowl sent to the primary pebble mills, see Fig. 1. In the pebble mill circuit the ore is ground to 90 pct —325 mesh (24 pct + 28 microns). In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO,, 80 pct insoluble. Its grindability at different meshes has been shown near the top of the list in F. C. Bond&apos;s grindability tests.&apos; Lake Shore is not shown, but an adjacent mine with identical ore, Wright-Hargreaves, is. Reasons for the Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1953

By R. S. Busk, R. F. Marande

The magnesium-aluminum-zinc &apos;system contains most of the magnesium-base alloys used commercially, although in practice the ternary alloys are usually modified by the addition of a small amount of manganese. Table I contains the magnesium-base commercial sand-casting alloys most widely used throughout the world, together with their typical tensile properties. These alloys may be regarded as a single family of varying aluminum and zinc content, disregarding manganese. A concise means of presenting data for them is by means of iso-property lines plotted on triangular coordinate paper. Constitutional, casting, and mechanical properties are presented in this manner. The data are given with the obiect of providing reference material, and to aid in the choice of a commercial alloy to serve a particular purpose. Detailed, critical analysis of the commercial alloys has been covered in a previous paper.&apos; All alloys reported were made in rj-lb. melts, superheated to r700°F. for 15 min., cooled to r400°F. and poured in sand molds. The test bars produced had a 1/2-in. reduced section and were about 6 in. long. Except for the data represented in Figs. I and 3 the alloys used were of commercial purity and contained 0.1 to 0.2 per cent Mn in addition to the aluminum and zinc. Constitutional Data Under the heading of Constitutional Data are included all known data on con-

Jan 1, 1946

By Hugh Henton

THIS paper is the result of an investigation made in association with Dr. Charles H. Fulton. Early in 1918 a search was started for methods of utilizing, in the manufacture of basic refractories, certain domestic resources in magnesites, dolomites, and magnesian limestones. Much information was collected during that year and during 1919 regarding magnesite and dolomite deposits. During 1920 and 1921 a research was made into methods of calcining dolomite and separating magnesia therefrom. Some success was attained and many new ideas were brought out in connection with the preparation and utilization of magnesia in the form of "caustic" or light-burned material as well as in the form of refractory or "dead-burned" material. Stimulated by this success, much advance has been made in manufacturing processes for the "plastic magnesia," so called, used for magnesia cement, stucco, flooring and otherwise in the structural industries.

Jan 3, 1926

By Lillian Erskine

While brass and other copper alloys have long been listed as offering health hazards to their workers, it is questionable if the metals involved are alone responsible for the trades&apos; records of morbidity. The entire science of foundry sanitation is the product of the past two decades; and the best standards now operative would have been regarded as little short of revolutionary prior to 1910. The special handicap to the conservation of the health of the brass founder&apos;s employees has been the fact that, unlike the iron founder, his business could be profitably carried on in almost any small and unsanitary quarters. As a result, writers on occupational disease have accepted brass chills or brass founders&apos; ague as an inevitable feature of the trade; and respiratory disabilities, as well as phthisis and disturbances of the nervous system, are also included as prevalent among those employed. While there can be no question as to the basic accuracy of past investigations, there is every reason to doubt the necessity for an undue percentage of ill health among brass molders and casters who are safeguarded by scientific ventilating standards and by improving personal habits of sobriety. There is, however, need for a campaign of education as to the most approved practices and equipment whereby the employer may safeguard the health of his workers, and thereby reduce his labor turnover and increase his productive efficiency. Broadly speaking, copper, tin, and aluminum carry negligible health hazards. The toxic qualities of lead, however, are a menace; especially if scrap lead is recovered or bought for foundry processes. The rapid volatilization of zinc renders its fumes and flocculent condensation the chief problems in conserving the health of the brass worker. The frequent presence in the foundry air of traces of arsenic compounds, lead

Jan 1, 1919

By R. F. Marande, R. S. Busk

The magnesium-aluminum-zinc &apos;system contains most of the magnesium-base alloys used commercially, although in practice the ternary alloys are usually modified by the addition of a small amount of manganese. Table I contains the magnesium-base commercial sand-casting alloys most widely used throughout the world, together with their typical tensile properties. These alloys may be regarded as a single family of varying aluminum and zinc content, disregarding manganese. A concise means of presenting data for them is by means of iso-property lines plotted on triangular coordinate paper. Constitutional, casting, and mechanical properties are presented in this manner. The data are given with the obiect of providing reference material, and to aid in the choice of a commercial alloy to serve a particular purpose. Detailed, critical analysis of the commercial alloys has been covered in a previous paper.&apos; All alloys reported were made in rj-lb. melts, superheated to r700°F. for 15 min., cooled to r400°F. and poured in sand molds. The test bars produced had a 1/2-in. reduced section and were about 6 in. long. Except for the data represented in Figs. I and 3 the alloys used were of commercial purity and contained 0.1 to 0.2 per cent Mn in addition to the aluminum and zinc. Constitutional Data Under the heading of Constitutional Data are included all known data on con-

Jan 1, 1946

By Clarence Zener

THE heat-treatment of steels will not pass from the stage of an art into that of a science until the mechanism of the phase transformations associated therewith is thoroughly understood. Such an under- standing will involve two distinct types of inquiry: (I) the direction of the trans- formation, (2) the speed of the transformation. The first type of inquiry, which involves only the equilibrium relations between the various phases in steel, is the subject of the present and of a succeeding article; the second type, which involves the kinetics of transformations, will be the subject of a later article. In order that a theory of equilibrium relations may give useful information, certain experimental data must be put into the theory. It is customary for these data to be of a thermal nature. In the system discussed here in steel such thermal data are very scarce. In medium-alloy steels another type of data might possibly be used. In these steels the concentration of solute is so low that it may be possible to use the approximation of dilute solutions, an approximation that leads to linear relationships. The unknown functions, or constants, may then be determined in some cases from the binary iron- alloy system and in other cases from the ternary iron-carbon-alloy system. From the functions, or constants, so determined may then be computed the equilibrium relations in more complex medium-alloy steels. In the present article this second approach is used, the necessary experimental data being obtained from the simple binary and ternary equilibrium diagrams. FUNDAMENTAL EQUATIONS In this article are derived the equilibrium relations between the gamma, alpha and cementite phases. In these three phases all important alloying elements except carbon form substitutional solutions, each alloying atom occupying a potential site for an iron atom. Carbon, on the other hand, forms an interstitial solution. In the face-centered cubic gamma phase, the interstitial positions are at the center of the unit cube and at the centers of the cube edges. There are therefore four interstitial positions per unit cell, or one per iron atom. In the body- centered cubic alpha phase, the interstitial positions are probably at the face centers, and also at the centers of the edges, which are crystallographically equivalent to the face centers. There are therefore six interstitial positions per unit cube, or three per iron atom. In cementite, (Fe, Alloy)3C, the carbon atoms may be regarded as filling all the lattice positions of a given type. The introduction of the fundamental equations of equilibrium has presented the author with a quandary. These equations are formally so similar to other equations that have been derived1,2 for related systems that they may appear to some readers

Jan 1, 1946