Search Documents

By W. C. Elli, M. E. Fine

YOUNG'S modulus of elasticity in metals ordinarily decreases with rising temperature. The range of the thermoelastic coefficient at room tem- 1/E dE/dT perature (temperature coefficient of modulus, is illustrated1 by the values for tungsten and hard-drawn aluminum, —95 and —1220x10-6 eg C-1. However, a nearly zero thermoelastic coefficient is observed in some ferromagnetic alloys over a limited temperature range. In these alloys, as the temperature is raised, an increase in modulus arising from loss of ferromagnetism compensates the normal decrease. Iron-nickel alloys containing 36 to 52 pct Ni behave in this manner. In the present investiga- tion, the dependence of the modulus and thermo-elastic coefficient on cold working and annealing were studied in iron-nickel alloys in this range of nickel. Although these alloys, when fully annealed, have a coefficient near zero over a very small temperature interval, the temperature range of low coefficient can be extended greatly by straining and then stress-relief annealing. The modulus of face-centered cubic iron-nickel alloys annealed at 1000°C does not vary linearly with composition at room temperature but, as shown by the solid line of fig. 1, from Koster,' is minimum at 40 pct Ni and maximum at 87 pct Ni. The modulus increases with applied magnetic field but retains the minimum near 40 pct Ni. Schematic change of modulus with temperature for three compositions is shown in fig. 2.'. ' With increasing temperature, the slope becomes less negative, goes through zero (temperature of minimum modulus for the alloy), becomes positive, and resumes its normal negative value above the Curie

Jan 1, 1951

By Carl F. Lutz, Robert F. Mehl

A layer of brass was formed on 0 brass using a vapor-solid reaction technique. The variation in composition with distance within the phase layer and across the a -ß interface was determined by an electron probe. The diffusivities were calculated as a function of concentration; the diffusion coefficient in brass was found to change by a factor of twenty-five over a compositional range of 8 at. pct. An explanation is proposed to account for the large change in the diffusivity, based on possible stresses in the diffusion zone; it is suggested that the concentration dependence of the thermodynamic factor might decrease the activation energy with increasing zinc content. ALTHOUGH the body of data on diffusion coefficients (D- values) in terminal solid solutions and in isomorphous systems is quite large, there is but little quantitative information for intermediate alloy phases. This paper recounts measurements of D-values for the ? phase in the Cu-Zn system. The experimental method employed consists in the forming of alloy layers and determining and analyzing the concentration-distance (c-x) curve. The experimental method employed could have been applied to several systems; the Cu-Zn system was chosen because the D-values in the a and ß phases are well known, and can thus be used for purposes of comparison. The rates of growth, of intermediate alloy layers are known for a number of systems. In nearly all cases the thickness varies parabolically with time, as to be expected if the rate of growth is controlled by the D-values. In a few cases, nonparabolic behavior has been noted.1 Nonparabolic growth may be the result of a) a variation of the composition at the phase interface with time, b) interface-controlled kinetics, c) short diffusion times coupled with long vacancy lifetimes (in vacancy diffusion),2 and d) crystal reorientation during diffusion in anisotropic systems.3 In the Al-Ni system4 and in the Al-u5 system parabolic growth kinetics are slowly approached after an initial transient period. In general those phases stable at a given temperature in a system A-B appear as separate phase layers when A and B are put in contact and given a diffusion he at-treatment. In most cases the compositions at the interface of adjacent phase layers are those read from the phase diagrams for the termini of the respective phases. This discontinuity in concentration is taken as independent of time, and the growth of one phase at the expense of another is assumed to be independent of interface kinetics, i.e., the rate of interface movement is controlled by volume diffusion in the phases concerned. wagner6 has given many solutions for multi-phase diffusion processes, assuming that the chemical diffusion coefficient, D, is independent of concentration, as have others. Jost7 has pointed out that the familiar Boltzmann-Matano solution is as valid for a (c-x) curve exhibiting concentration discontinuities at phase boundaries as for the usual single-phase case. Heumann and associates8,9 have applied this solution to the multi-phase case, but lacking concentration data within the several layers were forced to assume linear concentration gradients, thus calculating only average D-values. The purposes of the present study were: 1) to determine the dependence of D on concentration, 2) to calculate the intrinsic diffusion coefficients D?Cu and D?Zn, 3) to establish the time-law for the movement of the interface, 4) to determine the concentration limits at the ß-? interface, and, 5) to attempt to clarify the mechanism of diffusion. EXPERIMENTAL PROCEDURE The ? phase is exceedingly brittle; conventional solid couples and conventional sectioning methods were thus inapplicable. Vapor-solid couples were accordingly employed. Unfortunately the equilibrium vapor pressures of Zn for the ? phase are unknown; to escape this awkwardness, samples were enclosed in a capsule containing powder of an alloy of known composition, sufficiently large in quantity as to be effectively an infinite source, maintaining the concentration of Zn at the sample surface constant with time. The sources of Zn-vapor which can be employed in reaction with Cu, or a brass, or ß brass, to form a layer of ? brass satisfactorily wide in concentration range, are alloys of the phases ?, or ? + E or ? + d (depending on the temperature).

Jan 1, 1962

By John Fritz

MEMBERS of the American engineering societies who were in London and Paris during the last days of. June and early July were present at many interesting gatherings. The official delegates of the Founder societies were the specially honored guests of the foreign engineering societies, but other American engineers took part in the meetings. The members of the delegation were: Arthur S. Dwight, Charles F. Rand, William Kelly, representing A. I. M. E.; Ambrose Swasey (general chairman of deputation), Ira N. Hollis, Jesse M. Smith, representing A. S. M. E.; F. B. Jewett, A. E. Kennelly, G. O. Squier, representing A. I. E. E.; Charles T. Main, Robert A. Cummings, John R. Freeman, D. C. Henny, representing A. S. C. E.

Jan 1, 1921

By AIME AIME

WHETHER by the Mohawk Trail, Sound steamer, air plane, railroad or any other route or mode of locomotion, all roads will lead to Boston the week of National Metal Congress, Sept. 21-25. The Institute of Metals and Iron and Steel divisions of the Institute are then to meet jointly at the Hotel Statler, and the American Society for Steel Treating, the American Welding Society, the Society of Automotive Engineers and the Iron and Steel Division of the American Society of Mechanical Engineers present carefully planned programs at their respective sessions. The National Metal Exposition will be held on Commonwealth Pier.

Jan 1, 1931

By Joseph A. Holmes, Henry Kreisinger

At the Mining Experiment Station of the U. S. Geological Survey, in Pittsburg, an investigation of the process of combustion is being carried on in a specially-designed furnace having an unusually long combustion-chamber. This work is conducted by a con~mittee consisti~lg of 11. Kreisinger, mechanical engineer; Dr. J. C. W. Frazer, chemist; and Dr..J. K. Clement, physicist. The problem, essentially one of physical chemistry, is estremely interesting to all who are concerned in the burning of coal or the construction of furnaces. The main object of these experiments is to ascertain the relation between the amount of' the volatile combustible driven from the coal and the combustion-spaces necessary to burn it completely. Our best steam-coals vary from 15 to 45 per cent. in volatile matter and from 40 to 75 per cent. of fixed combtistible. The greater part of the latter is burned on the grate: but the volatile combustible leaves the freshly-charsed coal and must be burned in the combustion-space. If this space is not large enough, the volatile combustible mill leave the furnace only partly burnecl, and the result will be a considerable heat-loss and a smoky stack. Strictly speaking, the factor which determines the completeness of combustion of the volatile matter, after it has been mixed with a certain amount of air, is the length of time the mixture is allowed to remain in the combustion-space; but this length of time depends on the extent of the space itself. Let us suppose, for instance, that, when a given coal is burned at a certain standard rate, the volume of the volatile combustible driven oft' per second is 10 cu. ft. Adding, say, 10 cu. ft. of air, the volume of the resulting burning mixture is increased to 20 cu. ft. If the combustion-space is 30 cu. ft., the burning mixture will stay in it,

Jan 1, 1911

By John B. Dilworth

In September, 1930, H. N. Eavenson, then Chairman of the Coal Division, appointed a Committee on Methods of valuing Coal Propelvties, with John B. Dilworth as chairman. The latter prepared a schedule' of features for consideration under the general headings of Undeveloped and Developed Coal Properties. These subjects were divided among the members of the committee and during the next year written discussions of his allotted subjects were received from each member. Mr. Grimes and Mr. Eavenson discussed the entire list,. These discussions were mimeographed and a set sent to each member before the meeting of the Institute in February, 1932. There was a general discussion at that meeting. At the meeting in February, 1934, Mr. Dilworth submitted a report12 which summarized the accumulated opinions and data and presented the conclusions of the committee as a whole on the subjects embraced in it's schedule. Members of the committee expressed the desire that some of the individual opinions be published for reference. Mr. R. Damon Hall's abstracts of these papers arc therefore presentrd herewith.3 Personnel of Committee John B. Dilworth (Chairman), Consulting Mining Engineer, Edward V. D'Invilliers Engineering Co., Philadelphia, Pa. Eli T. Conner, Consulting Mining Engineer, Seranton, Pa. W. G. Duncan, Jr., Superintendent, W. G. Duncan CoaI Co., Greenville, Ky. Howard N. EAveNson, Consulting Mining Engineer; Eavenson, Alford & Hicks. Pittshurgh, Pa. George Watkin Evans, Consulting Mining Engineer, Seattle, Wash. J. A. Garcia, Consulting And Constructing Engineer, Allen & Garcia Co., Chicatgo. III. John Alden Grimes, Valuation Engineer, Bureau of Internal Revenue, Washington, D. C. Otto Herres, Assistant Manager, United States Fue1 Co., Salt Lake City, Utah. J. R. Hicks, Consulting Mining Engineer, Eavensorl, Alford & Hicks, Pittsburgh, Pa. Robert D. Reeder, Mining Engineer, U. S. Bureau of Mines, Washington, D. C. Samuel, A. Taylor, Consulting Engineer, Pittsburgh, Pa. Bleeckee L.. WHeeler, Mining Engineer, Ford, Bacon & Davis, New York, N. Y.

Jan 1, 1934

By John A. Gann

THE Iron and Steel Division has shared in the general increased activity of the industry. The fall meeting at Chicago was not only well attended but particularly characterized by the virility and scope of the discussions at the various sessions. The program for the February meeting indicates a similar interest in technological developments. The Blast-Furnace Committee continues to have the hearty support of the industry with discussions of such a nature as to be of real help to the operator as well ass the technologist. The work of the Open-Hearth Committee continues to be outstanding, with ever increasing attendance and ever mounting interest in the meetings. Formation of a conference on the physical chemistry of steelmaking has given those interested in this phase of work an organization allowing the same

Jan 1, 1936

By AIME AIME

TWO technical sessions, an excursion through the Midwest refinery and a smoker, marked the first day of the meeting of the Petroleum Division at Casper, Wyo., on Aug. 28. Ninety-nine members and guests registered and there was an excellent attendance at 'all functions. The -local committee under the general chairmanship of J. C. Lindsay, general manager of the Western Pipe Line Co., had made every possible arrangement for the convenience and comfort of the visiting members and the Program Committee under E. L. Estabrook, vice-chairman of the Petroleum Division, had brought together a most interesting series of technical, papers. The meeting centered mainly on the various features of the Salt Creek field but there were also contributions from the technology of production in California, the Mid-Continent, and the Texas fields. The opening session was called to order by Mr. Estabrook at the Townsend Hotel on Friday morning. The members and visitors were welcomed appropriately by Ex-Governor B. B. Brooks, president of the "Rocky Mountain Oil and Gas Association, who recalled the changes that had taken place as Casper, a frontier cow town, became a thriving oil metropolis. F. Julius Fobs, chairman 'of the Petroleum Division, responded and then took the chair. He introduced H. Foster Bain, Secretary of the Institute, who expressed the regret of those members members who found it impossible to stop over en route to Salt Lake City and his own pleasure at meeting with the Division in the field. Following these introductory ceremonies the technical session began with a "Sketch of the Geological Formations of Central Wyoming," presented by J. G. Bartram of the Midwest staff. It was brief and to the point and contributed greatly to the easy under¬standing of the succeeding papers by those unfamiliar with the region. The talk was illustrated by a large scale columnar section -and a copy of the excellent, geological map of the State recently issued by the U. S. Geological Survey.

Jan 1, 1925

By F. R. Milliken

EXPERIMENTS, in what has come to be known as flash roasting began some ten years ago. The principle underlying the operation was not a new one, but the experimental work started at that time was the first that was carried through to a logical conclusion, followed by construction and operation of a pilot plant, and then full-scale production. For a short working definition, flash roasting may he considered the instantaneous and complete oxidation of finely ground sulphide particles, partially suspended in air or gas, the oxidation reaction evolving enough heat to make the reaction self-sustaining, or nearly so.

Jan 1, 1937

By AIME AIME

Adjustable Pyrometer-Stand. By L. W. BAHNEY, xxxvii, 33. Agency of Manganese in the Superficial Alteration and Secondary Enrichment of Gold-Deposits in the United States. By WILLIAM H. EMMONS, xlvi, 767. Application of Descriptive Geometry to Mining-Problems. By JOSEPH W. ROE, xxxix, 173. ARNOLD, C. EVERARD. The Giroux Shaft at Kimberly, Nev., xlii, 461. BAHNEY, L. W. An Adjustable Pyrometer-Stand, xxxvii, 33. BALL, SYDNEY H., and SHALER, MILLARD K. Mining-Conditions in the Belgian Congo, xxxix, 253. BEALS, ROGER L., and TWEEDY, GEORGE A. Cyanide-Plant and Practice at the Minas del Tajo, Rosario, Sinaloa, Mexico, xxxviii, 123.

Dec 1, 1910

By D. W. Loucks

There is plenty of evidence to indicate that at least one of man's chief interests in life is to make himself as comfortable as possible. If you doubt this, just watch the fellow next to you for the next half hour trying to find the most comfortable position that a hard chair has to offer. Comfort, however, does not always mean an easy chair. To some, it may mean a wealth of money: to another, freedom from worry. But to most of us, it means first of all a comfortable atmosphere in which to live, and to a great many of us it probably also means freedom from that annoying task of firing the furnace. Today more than ever before, automatic heat is one improvement that is placed high on everyone's list. Perhaps this is because automatic heating is becoming relatively cheaper. Perhaps it is because of a good publicity campaign on the part of the oil and gas men or maybe it is just that we are getting lazier day by day. At any rate, almost every issue of Better Homes and Gardens, House Beautiful, or your other favorite home magazine carries an article extolling the virtues of this or that automatic heating system.

Jan 1, 1949

By Albert J. McIntosh

With petroleum consumption declining temporarily after V-J day, the oil industry is urged to use this period as a kind of stopgap to rebuild its war-depleted inventories and help cushion the effect of this decline on producers and refiners. Higher inventories should be reestablished, since recent experiences have indicated that, by and large, the present inventories of crude oil are too low even with the tremendous current production available. The following analysis indicates that inventory levels could be built up to about 490,000,000 bbl. by the end of 1947, an increase of about 40,000,000 bbl. over the reported stock estimated for the war's end. If at the end of the war the military have some 20,000,000 bbl. on hand, this inventory will either be resold to the industry or certain demands that have been assumed to be met by industry will be supplied out of these military stocks, which would leave about 20,000,000 bbl. (net) to be built up from current production. For stock rebuilding the industry could use 10,000,000 bbl. of crude plus 10,00,000 bbl. of products, totaling 20,000,000 bbl. If this were spread over a year, this would mean 55,000 bbl. a day. By analyzing the average inventories held in a year with the total quantity of goods handled during the year, the following study and tables indicate how far the inventories should increase in the immediate postwar period. Introduction For the period immediately following V-J day, most of the petroleum economists have forecast a considerable decline in the total consumption of petroleum and its products in the United States. This will be caused by the elimination of most of the military demands and the inability of civilians to immediately replace automobiles, burners, etc., and thus increase their requirements to make up for the military decline. When the automobile industry has been back on full production for two or three years, civilians will be able to consume much larger quantities of gasoline. Delay in the manufacture of new oil burners and the time it takes to construct new homes, adds up to the same story for distillate fuels. In reviewing this outlook, the question has arisen whether the petroleum industry should not use this period of lower consumption as a kind of stopgap to rebuild its war-depleted inveritories and help cushion the effect on producers and refiners of this sudden drop in requirements. Some persons have indicated that hundreds of thousands of barrels a day could be used for this purpose extending over a year or more. Refineries will be in existence, which could run over 5,000,000 bbl. of crude oil a day and crude-oil production might be running 600,000 to 700,000 bbl. a day above the demands now forecast for the period after V-J day. Reasons for. Making Inventories In order to plan intelligently for this period, the petroleum industry should determine the needs for the establishment of higher inventories for crude and petroleum products than have been carried during the war. The reasons for trying to make such a determination are as follows:

Jan 1, 1945

By AIME AIME

The name and address of the school are given first, followed by the length of the regular undergraduate curriculum, the degree granted, types of courses giben, and the name of the man in charge. This covers only work for the first or Bachelor degree in each case. The following abbreviations are used: B. Bachelor Cer. Ceramic. E. Engineer or Engineering Eng. Engineering or Engineer Geol. Geologist, Geological, or Geology M. Mines or Mining Met. Metallurgy or Metallurgical Mng. Mining Pet. Petroleum Ref. Refining S. Science Tech. Technology or Technical

Jan 1, 1939

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board; the Institute itself has three awards to make annually, as follows: the Robert W.' Hunt Medal and Prize, the J. E. Johnson, Jr. Award, and the James Douglas Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes; first of a. gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or Papers on iron and steel. The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of. the subject have preference over those dealing with the theoretical, side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the. award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be designated "The Hunt Medallist." This prize is administered. by the iron and Steel Committee. J. E. JOHNSON, JR., AWARD This award is made from the income of a fund of $30000 donated by Mrs. Margaret Hilles. Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practise, vice-chairman of the Institute's Iron. and Steel Committee, and a frequent contributor of papers to the Institute's TRANSACTIONS. This prize is administered by the Iron and Steel Committee. The intent of the donor is to encourage young men in creative work in branches of the metallurgy or manufacture of pig iron with which the professional activities of Mr. Johnson were chiefly concerned. The control off the fund and distribution of the awards having been vested in the Board of Directors of the Institute, this Board has made the following regulations concerning it:

Jan 1, 1925

By R. D. Longyear

[Some Problems Involved in the Interpretation of Diamond-drill-hole Sampling and Surve ing (paper by J. J. Collins, Mining Tech., Jan. 1946). ............... I Geologic Interpretation of Magnetic Exploration on the Mesabi Range, Minnesota (paper by R. H. B. Jones, Mining Tech., July 1946) ................... 2] DISCUSSION R. D. LONGYEAR.*-Mr. Collins is to be commended very highly for the brief summary he has made of the currently used methods of taking diamond-drill sludge samples and the principles involved in evaluating the results. This paper should stimulate further discussion and research on this vitally important problem. It is particularly imperative that geologists and engineers know when assay results on sludge recovery can be accepted quantitatively and when they must be considered only qualitatively. In most cases where the sludge recovery is less than 95 per cent or more than 125 per cent, it is safest to consider the assays as of qualitative value only. Certain cases, however, are known where a relatively small proportion of the sludge sampling will give a reasonably accurate measure of the value of the total sample. One such case is ore in which the valuable mineral is of approximately the same specific gravity as the waste mineral, such as chalcopyrite in a massive pyrite body. The essential point is to determine the degree of accuracy of sludge sampling in any given drilling project and to weigh the results accordingly. It should be emphasized, however, that sludge sampling can be made reliable in many localities where careless practice produces unreliable results. In many instances, it is desirable to empty the core barrel in the core shack instead of at the drill, so that the engineer can examine the core as it first comes from the core barrel. It should be pointed out, however, that the drill * E. J. Longyear Co., Minneapolis, Minnesota. runner should be permitted to study the core to guide his future drilling. It is hoped that with the return of more normal conditions after the war geologists, engineers, contractors, and manufacturers will be able to carry on more research along the lines of improved core-barrel design and drilling technique with the objective of increasing core recovery so as to eliminate as far as possible the necessity of relying upon sludge samples. H. M. ROBERTS.*-Whoever in the future will have to do with the search for ore bodies and their exploration will have frequent occasion to refer to the clear and comprehensive summary on diamond-drilling methods by John Collins. His review of the experience of the last 40 years in this technique is invaluable. As Dr. L. D. Ricketts wrote in 1932, "The principles on which an art is founded are usually few and necessarily basic in nature, but he who wishes to achieve the power to select his aides and give success to important undertakings that may be intrusted to him in the future must ordinarily undergo years of drudgery in order to gain the experience that will enable him to distinguish such fundamentals through the haze of reinforcing detail that clothes and tends to disguise them."[t] Ricketts went on to say that since the beginning of the century there has been much

Jan 1, 1946

By G. C. Kuczynski

Two particles in mutual contact form a system which is not in thermo-dynamical equilibrium, because its total surface free energy is not a minimum. If such a system is left for a certain period of time, the bonding of the two particles will take place in order to decrease the total surface area, even though the temperature is lower than the melting point. This phenomenon of bonding of two or more particles with the application of heat only and at temperatures below melting point of any component of the system will be called sintering, although the powder metallurgists use this term in a broader sense, including the presence of molten phase and pressure. It is the objective of this paper to study this process and the mechanisms involved in it. This problem is of utmost importance to powder metallurgy and powder ceramics, and its technological aspects have been studied for a good many years. However, the powder metallurgical operations are too complex and include too many superimposing mechanisms, and too many variables for a direct study. It was therefore advisable for the purposes of this study to reduce the variables to a minimum. In this work the radius of the interface formed during bonding in a simple system composed of a spherical particle and a large block of the same metal was studied as a function of time and temperature. It is believed that the mechanism involved in this simple process is fundamental to any sintering operations. Previous Work J. Frenkell was the first to make a serious attempt to develop a theory of sintering. He assumed that the process consists of a slow deformation of crystalline particles under the influence of surface tension which reduces to a viscous flow where the coefficient of viscosity n is related to the self-diffusion coefficient D by the following equation 1 _ D D6kT [1] where 6 is interatomic distance, k the Boltzman constant, and T the absolute temperature. This type of viscous flow of a crystalline substance is essentially different from the ordinary plastic flow. The latter is a specific propcrty of crystals and cannot take place in amorphous bodies. According to Frenkel this viscous type of flow is due to the diffusion of the holes or vacancies arising in the lattice. He was able to derive an equation relating the growth of the interface between two spherical crystalline particles or between a particle and a semi-infinite crystal (Fig 1) to time t at constant temperature. This relationship can be written as follows: x²— 3/2 a/nt [2] where x is the radius of the interface assumed to be circular, a the original radius of the sphere and a surface tension of the material. The other assump- x tions are that x is less than 0.3 and that during the period 1 the original radius, a, of the metallic particle did not change appreciably. A. J. Shaler and J. Wulff2 followed closely the ideas of Frenkel in their theory of sintering of a mass of metallic powder. Neither Frenkel nor Shaler has validated his theoretical speculations with conclusive experimental data. Two measurements reported by

Jan 1, 1950

By L. D. Ricketts

AN older man looks back, perhaps wistfully, on a long and rather active experience, and possibly a popular and brief glimpse of some contrast between past and present may hold your attention for a few brief moments and prove useful. In the late nineties an engineer was .called on to de- sign and build two copper ore concentrating mills of 400 tons average daily capacity. There were larger mills than this at Washoe and elsewhere, but a 400 ton' mill was a large one as mills went over thirty years ago, and one might say a large mill of those days could crush a ton of copper ore in 216 seconds. In the mills I refer to steel construction and the conveying belts were introduced into the copper industry and rein- forced concrete came shortly after. Since then we in the West have ever been faced with a constantly de- creasing tenor in the grade of our copper ores and a constantly increasing demand for our product, and we have therefore been obliged to call for far larger castings and finished machines than were formerly used. The mechanical engineer has also enabled us to accomplish notable economies in power generation and distribution. Ore handling and crushing have been simplified and through the introduction of reagents to induce physical or chemical reactions, or both, our older methods have been vastly improved or even supplanted by new and better ones and our recoveries greatly improved.

Jan 1, 1929

By C. E. Birchenall, W. Batz, H. W. Mean

AT temperatures between 1095' and 1347ºC, 13 runs have been made on the diffusion of silicon in iron. In two of the runs the couple compositions were entirely within the loop of the Fe-Si system; the base alloys contained 0.0 and 1.0 wt pct Si. The other runs in which the couples consisted of a 2.3 wt pct Si alloy welded to a 3.7 pct Si alloy were a phase throughout. The alloys were made by melting electrolytic iron and commercially pure silicon. Trace impurities were not determined. The butt welded couples were diffused in an inert atmosphere of argon or hydrogen. After cooling, cuts of two mils or greater thickness were machined parallel to the weld interface. The chips were analyzed for silicon. When the concentration and distance data were examined on the conventional probability plot,' no marked variation of the diffusion coefficient with concentration was indicated over the narrow composition ranges employed. Therefore, a single diffusion coefficient is recorded for each run in Table I. The temperatures and atmospheres of the diffusion anneal are listed along with the compositions of the base alloys. For a iron the silicon diffusion coefficient is given by the equation: D = 0.44 e-48,000/RT where R is the gas Constant and T, the absolute temperature. However, since the scatter in the data is fairly large, the activation energy may be in error by as much as 6000 cal per g-atom. The two ? iron points do not permit estimation of the activation energy with any reasonable certainty. They do indicate that the coefficients reported by Smithells2 and Jost,3 based on the work of Fry,4 are much too high. Although very dilute solutions in iron of manganese,5 nickel,8 cobalt,7 and molybdenum8 give dif- fusion coefficients quite close to those obtained for self-diffusion in iron, the silicon values are considerably higher, though of the same order of magnitude. This seems to be consistent with the fact that the silicon atom is the only one of those listed here which is appreciably smaller than iron. The authors are grateful to the Office of Naval Research for their support of this work under Contract N6ori-47, Task order IV, Project NR 031-184, to J. K. Stanley and the Westinghouse Research Laboratories for the silicon alloys used, to several steel companies for the silicon analyses, and to C. Wells, of the Metals Research Laboratory, Carnegie Institute of Technology, for numerous suggestions during the course of the work. References 'C. Wells: Atom Movements (1951) Chapter 2. A.S.M. 2C. J. Smithells: Metals Reference Book (1949) p. 405. Interscience. Pub. Co. 3W. Jost: Diffusion (1952) p. 223. Academic Press. 4 A. Fry: Stahl und Eisen (1923) 43, p. 1039. T. Wells and R. F. Mehl: Trans. AIME (1941) 145, p. 315. "C. Wells and R. F. Mehl: Trans. AIME (1941) 145, p. 329. 7M. F. Hawkes and R. F. Mehl: Trans. AIME (1947) 172, p. 467; Metals Technology (August 1947). .J. L. Ham: Trans. A.S.M. (1945) 35, p. 331.

Jan 1, 1953

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has five major awards to make annually for excellence in technical papers, as follows: The Robert W. Hunt Medal and Prize, The J. E: Johnson, Jr. Award, The Lewisohn Platinum Prize to senior members, and the James Douglas Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to' establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes; first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term" iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition. of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be ,designated "The Hunt Medallist." This prize is administered by the Iron and Steel Committee. J. E. JOHNSON, JR. AWARD This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practise, vice-chairman of the Institute's Iron and Steel Committee, and a frequent contributor of papers to the Institute's Transactions. This prize is administered by the Iron and Steel Committee. The intent of the donor is to encourage young men in creative work in branches of the metallurgy or manufacture of pig iron with which the professional activities of Mr. Johnson were chiefly concerned. The control of the fund and distribution of the awards having been vested in the Board of Directors of the Institute, this Board has made 'the following regulations concerning it:

Jan 1, 1925

By H. Stuart, L. Zwell, N. Ridley

specimen that was subjected to 700°C for 250 hr is shown in Fig. 2(c). The precipitates in this foil appear round and exhibit only very faint strain contrast. From this evidence, along with that described above for the symmetry of the strain field, it may be concluded that this coherent precipitate is spherical, which is generally the favored shape for coherent precipitates when the lattice parameter mismatch is small.12 These observations are consistent with the assumption that this precipitate is the y' (Ni3Al, Ti) phase. y' is known to be spherical in the early stages of precipitation. It is fcc and is similar in composition to the matrix and thus would have contrast similar to that of the matrix as do these precipitates. Direct identification of the spherical precipitate did not prove possible because of its low volume fraction and small size. The results of this investigation suggest that the increases in yield strength and the decreases in elongation observed in 45-Fe 30-Ni 20-Cr alloys containing about 0.4 pct A1 and 0.4 pct Ti on prolonged aging at 550" to 700°C are very likely due to the presence of a coherent, spherical precipitate, thought to be y'. Mi-crohardness measurements indicated that the precipitation of semicoherent M23C6 resulted in some matrix hardening. However, this precipitation process occurs much more rapidly than the changes in mechanical properties at these temperatures. 1C. L. Clark, J. J. B. Rutherford, A. B. Wilder, and M. A. Cordovi: J. Eng. Power, 1962, vol. 84, p. 258. 2 F. A. Comprelli and U. E. Wolff: USAEC Report GEAP-4745, General Electric Company November, 1964. 3C. N. Spalaris: A Monograph, USAEC Report GEAP-4633, General Electric Company, July, 1964. THERE have been many X-ray investigations of the room temperature lattice parameters of austenite which has been retained in quenched steels of various carbon contents. The results of these investigations have been collected by Wrazej,1 Wever et al.,2 and by Roberts3 and are included in Fig. 1 due to Pearson.4 The dashed line in Fig. 1 was considered by Roberts3 to most reliably describe the variation with carbon content of the lattice parameter of retained austenite. This line is given by the equation: a (Å) = 3.555 + 0.044 wt % C and recent unpublished measurements by one of the authors (LZ) support this relationship. The object of this communication is to draw attention to a relationship which describes the variation of the room temperature lattice parameter of 'equilibrium' austenite with carbon content, and which is different from that for retained austenite. The relationship a(Å) = 3.573 + 0.033 wt % C has been obtained from lattice parameter measurements made on equilibrium Fe-C austenites at elevated temperatures, which have been extrapolated to room temperature. The room temperature lattice parameter of 3.555Å which the Roberts' relationship gives for pure y-Fe is no: in agreement with the value of 3.573Å obtained when the high temperature lattice parameter data of Basinski et aL.5 and of Goldschmidt6 is extrapolated to room temperature. A linear extrapolation was

Jan 1, 1970