Search Documents

By Thorp D. Sawyer

In June 1914, one week before I was to be awarded my sheepskin in upper New York State, I received a telegram from New York City which read "Can offer you position as engineer in Chile at $115 a month contract for one year. (signed) Chile Copper Co." That night, Friday, I took a sleeper to New York and arrived at the Guggenheim Brothers' company office at 165 Broadway, just as it was opening up on Saturday morning. Saturday was no holiday in that era. Presenting the telegram at the office, I was ushered into a sub-executive's office and shown a mimeographed contract which 1) agreed to pay me $115 per month from the date of leaving New York until I returned, and with travelling expenses both ways, 2) fixed a charge of $46 per month for board and lodging in company quarters, and 3) stipulated a contract term of one year with the right to retain my services for another year if the company so elected. While a bit huffed at the year's "kicker" I nevertheless accepted. I was then told to prepare to leave the following Wednesday (June 17) on a United Fruit Co. steamer for Panama. Objecting that I still had to receive my degree on the 17th and had planned a vacation in Ohio for a week or so…

Jan 12, 1960

By J. G. Hadley

IN THE early stages of the depression the Utah Copper Co. realized that an unemployment problem would he created which demanded an intelligent and sympathetic solution. The company recognized that as many men as possible must be kept at work on a basis which would ultimately permit of the most efficient reabsorption of displaced labor. The company therefore determined to distribute available work among the greatest number of men and to that end adopted a system of rotating employees on a part-time basis. An employer requires a certain number of days' or shifts' work during the month. Obviously one employee working thirty days or shifts a month is equal to two employees each working fifteen. In principle, therefore, where two employees equally fitted to do certain work are available the work could be divided between them on an equitable basis and twice as many persons would benefit. A rotation plan on this basis was adopted by the Utah Copper, Co. on Jan. 30, 1930. Some variations of the orig¬inal plan have been made from time to time, the reasons for which will be discussed.

Jan 1, 1932

SAFETY in open-pit mining receives a minimum of notoriety, but its significance in profitable and efficient operation is as great as in other methods of mining. Open-pit operators from Arizona, New Mexico, and Mexico, exchanging ideas on safety at a symposium during the recent annual meeting of the Arizona Section, AIME, discovered unanimity of opinion that the successful safety program depended on managerial and supervisory support with the vigorous cooperation of the employes. Safety Organization The operation of a safety program is dependent on the ability of management to project enthusiasm through the company organization. This requires a suitable method of communication to the supervisory and employee levels so as to approach them in a manner that will inspire cooperation. Safety committees comprised of various combinations of managerial, supervisory, and employe personnel are frequently used for this purpose. The open-cut mine of the Chino Division of the Kennecott Copper Corp., Santa Rita, N. Mex., operates its program through management, a full-time safety engineer, and two safety committees, the Departmental and Shops Safety Committee and the Central Safety Committee. The Departmental and Shops Committee consists of one employe from each department and shop and the safety engineer. The selected members serve for a period of one month. This committee meets once a month, the only representative of management being the safety engineer because it is believed that employes will speak more freely when their supervisors are not present. The duties of the committee are to report hazardous conditions and make recommendations, but the committee has no authority to approve or disapprove. The Central Safety Committee is comprised of supervisory personnel from all departments and shops, and one member of each of the five bargaining organizations. Members of this committee are permanent and hold meetings soon after the departmental group to take action on recommendations of the latter. The committee system insures participation of all levels of personnel in the accident-prevention program, thereby stimulating safety consciousness. The New Cornelia branch of the Phelps-Dodge Corp., uses three groups to conduct the safety program; the General Safety Committee, Division Safety Committee, and the operating-unit safety meetings. The unit safety meetings provide for active participation of employes in discussion of various phases of the program. Within these groups vigorous opinions regarding safety are often expressed and the workmen are critical if they recognize a digression from the adopted safe-practice procedures. These monthly discussions give the program vitality. The Division Safety Committee is composed of the division superintendent and the division department heads, and follows an established pattern in discussion of all phases of the safety program. The General Safety Committee, made up of the manager, division, and department heads, makes decisions on policies and procedures; it renders decisions on recommendations and suggestions. Management at the New Cornelia branch feels this system of safety committees and meetings has been active in advancing the program. Safety Codes In the open-pit mines of the Southwest, a safety code for operation or service of equipment, methods

Jan 1, 1952

By L. D. HUNTOON

MY first article on Canadian Gold, published in the Canadian Mining Magazine in 1911 expressed the view that the Hollinger mine would repay all the money invested and that other mines would be developed in this area. Many published forecasts have since been made. Quoting from the Northern Miner of Oct. 29, 1931: "It will be noted in studying the chart prepared by this engineer that his forecast for 1931 at $50,000,000 was too modest, as the output for this country this year will be closer to $54,000,000."

Jan 1, 1932

The following additional notes about prices of coal in the early days were collected from the sources shown. Several data about canal tolls and labor conditions are also included. 1796, November: "The inhabitants lay it (coal) in at about 3;d. (83¢) sterling per bushel." (Ref. 73: p. 147.) 1804, March: "In March, 1804, I sent a person accustomed to mining to open the vein of coal, and to load the ark, which was accomplished, and early in the month of April the ark, with the first cargo of bituminous coal passed safely the Conewago falls, and landed her coal at Columbia, Lancaster County. The coal was sold at 31¢ per bushel at Columbia." ($7.75 per ton). This was the first coal from Clearfield County near the town of that name. (Letter from William Boyd: Pa. Senate Jour., 1833-1834, vol. 2, p. 561.) 1807: The following notice appeared in the Bedford Gazette: "Huntingdon, June 4. "Stone Coal.-Such of the farmers as wish to make experiment with stone coal as a substitute for plaster, in manuring their Indian corn, may be supplied with coal gratis upon application to Peter Hughes, at Mr. Riddle's mines, on the Raystown Branch. The proprietor of the mines offers not only to refund the carriage, but to pay the expenses of applying the coal, if upon a fair experiment it is found to be inferior to plaster, which now sells at two dollars per bushel." (Ref. 735: p. 708.) 1809: Coal was delivered in Pittsburgh at 5¢ per bushel or $1.25 per net ton. (Ref. 444: p. 50.) Coal was delivered in Connellsville at 4¢ per bushel or $1.00 per net ton. (Ibid.: p. 185.) 1810: Pittsburgh.-"Coal may be obtained of a good quality, ready delivered at 5¢ a bushel." ($1.25 per net ton.) (Ref. 315: vol. 2.) 1811: "It (coal) costs 6¢ a bushel at your door." ($1.50 per net ton.) (In Pittsburgh.) (Ref. 277: 1811, p. 68.) 1814: At Columbia, now part of Donors, Washington County, Pa., an original sale of lots in 1814 gave the purchaser of each lot the right to mine stone coal gratis from a bank on the property. (Ref. 410: vol. 1, p. 547.) "A laborer is able to dig upwards of 100 bushels per day." (4 tons.) (Ref. 277: 1814, p. 109.) A paper about the early newspapers in West Virginia says: "Collier Wanting. From 10 to 20 steady and industrious men, who understand digging coal, may obtain high wages in Kenhawa for that business, if immediate application is

Jan 1, 1942

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.' In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944

By Donald C. Barton

Success in the use of the Eötvös torsion balance method of mapping geologic structure depends largely on the accuracy in the interpretation of the observed results. Skill in that interpretation depends (1) on the knowledge of the types of the variation of gravity, the gradient of gravity horizontally, and of the differential curvature produced by bodies of different sizes, shapes, dimensions, and densities; (2) on the knowledge of the possible types of structural bodies which might produce the observed anomalies; (3) on the empirical knowledge gained by experience not only in the geological interpretation of torsion balance surveys, hut of interpretations of inadequate geological data; and (4) on a knowledge of the possible and probable types of geologic structures in the area of the survey. The knowledge of the anomaly which a known body will produce and conversely the knowledge of the body or bodies which will produce a known anomaly may be gained by empirical experience and by mathematical study. The knowledge gained by empirical experience is fragmentary and inexact. The geology of most structures actually is known very superficially. The surface geology may be known accurately. If the structure is petroliferous, the subsurface geology of the oil field will be known down to 3000, 4000, 5000 ft. or in a few oil fields down to 7500 ft., but the deeper geology will be unknown and the metamorphic, igneous, or massive limestone basement below the reach of the drill may contrast sharply in density with the overlying sediments. Away from the oil field, the subsurface geology is known only from scattered drill holes, which do not go to the basement. A fair but not necessarily accurate knowledge of the geology of the nonproductive area can be obtained by correlation of the wells but the degree of its accuracy in general is proportional to the density of the occurrence of the wells. The geology below the bottom of the wells however is unknown. An anomaly mapped by the torsion balance is the sum of the effects of the contrasts in mass of its whole geologic surroundings. If the dimensions of a body of abnormal density are large enough, depth or distance makes no difference in the effects on the gradient and differential curvature; and as a matter of fact, in many places, the basement and irregulari-

Jan 1, 1929

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.' In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944

By H. Foster Bain

THE "miracle of production." which was such an essential element in winning the European war, was nowhere more in evidence than in our Western States. In shipbuilding alone the Pacific Coast States -et a mark never before equaled, and in production of war goods of many kinds, both Rocky Mountain and Coast States accomplished more than their proportionate share if measured by population standards. This was only possible because of the building of immense new plants of many types, largely financed with Government money. Their operation has built up payrolls in the West and brought a measure of prosperity which Westerners are naturally anxious to have made permanent. A widespread doubt obtains, however, throughout the nation and even in the Western States themselves, as to whether, and if so to what extent, this may prove possible. The question has been raised as to whether the national treasury has not been raided to stock the Western ranges with a voracious breed of white elephant .

Jan 1, 1945

By William J. Coulter

WITHIN the past thirty years the United States has been involved in two tragic, vicious, and costly world wars. To make the world safe for democracy was the reason given for our participation, but the confusion and misunderstanding that prevails all over the world today suggests that war is not the proper approach to the attainment of that utopia. These conflicts were conceived and prosecuted by nations far advanced in civilization and culture. Their best manhood was sacrificed, a staggering tax burden was saddled on their peoples, huge financial losses were incurred, destruction of property was appalling, and cultural and peaceful scientific advancement received a setback that may require centuries to retrieve. Therefore, some basis is established for the conclusion that progress in the past fifty years has been most outstanding in the development of instruments used for death and destruction, and that progress in this direction between the two World Wars would indicate that the next war will go far toward total destruction of world civilization.

Jan 1, 1946

By G. St. J. Perrott

One of the important hazards in coal mining is the danger of ignition of explosive mixtures of methane and air or coal dust and air, or both, by the explosives used in blasting the coal. It has long been recognized that certain explosives are more dangerous than others in this respect. ' In America and abroad, government testing stations have been established for officially passing on the suitability of explosives for use in coal mines. In this country the Federal government is given no power to enforce the use of the approved explosives but merely publishes from time to time, through the Bureau of Mines, those explosives which have passed the tests necessary to place them on the list for use in coal mines. In spite of this lack of police power, the increase in the use of permissible .explosives since the promulgation of the fist list in 1909 has been rapid. In 1912, only 8 per cent. of the explosives used in coal mines were permissible; in 1925, this figure had increased to 25 per cent. While the past record of permissible explosives has been most gratifying, it is very desirable that we pave the way for further improvement in explosives and blasting methods by learning more about the mechanism of ignition of gas and coal dust by explosives. To this end a considerable amount of investigative work already has been carried out and a large amount yet remains to be done. It is the purpose of this paper to discuss briefly the effect of the characteristics of explosives and method of loading in the borehole on the liability of a blown-out shot to ignite explosive mixtures of gas or dust. For an account of the methods by which an explosive is tested for permissibility for use in coal mines, the reader is referred to Schedule 17-A of the U. S. Bureau of Mines. Safety Factor in Using Explosives The factors that affect the liability of an explosive to ignite gas or dust are already known in a qualitative way but quantitative data are

Jan 1, 1927

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by plotting [So = ooT as a function of eo =o] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors? It was shown that the true physical behavior of the material in the tension test could best be represented by plotting the average true stress, [S = P] as a function of [e = q' = log A-le = log Lo] where P, A, L, S, [e], and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941

By Arthur B. Yates

Diamond drilling has advanced and expanded during the past few yean. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. Control A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing— even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved. however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the

Jan 1, 1946

By H. H. Podgurski

Above 200°C the observed increase in the apparent solubility of hydrogen in low alloy steels caused by cold work is attributed to the formation of methane in microvoids. This methane can be isolated quantitatively, and furthermore, the amount of methane is in accord with the equilibrium 2H2 + Fe3C = CH4 + 3Fe. The micro-void volume, calculated from the methane content via the equation of state for methane, corresponds approximately to that calculated from the measured density decrement produced by cold work. THIS investigation was undertaken with the intent of employing the hydrogen atom as a probe in detecting specific crystallographic defects in cold worked steel. It was expected that different degrees of chemical interaction of hydrogen with the various types of defects could be utilized. The original aim was to assign concentration values to defect sites. The success of this approach requires that experimental conditions can be attained under which lattice-dissolved hydrogen equilibrates primarily with only one type of defect. A set of experiments which appeared potentially to embody these requirements was described several years ago by Keeler and Davis.1 They noted in the case of a mild steel (low carbon) that the solubility of hydrogen between 200° and 400°C near atmospheric pressure was notably increased by cold working the steel. The observed solubility was an order of magnitude greater than the normal lattice solubility. * Although the Keeler and Davis studies suggested that the density decrement effected by their cold-working operation might be related to the anomalous solubility of hydrogen, they offered no explanation of the relationship between the two effects. Prior to this work, Darken and smith3 had noted a similar effect of cold work upon enhanced sorption of hydrogen by steel when charged by acid pickling. In the light of present-day concepts, interaction between lattice-dissolved hydrogen and dislocations was strongly suggested. More recently, Hill and Johnson,4 working with a

Jan 1, 1962

By D. V. BURR

THE ORIGINAL HUDSON RIVER TUNNEL. NOT quite forty years ago a man of uncommon character entered New York. He had several hundred thousand dollars earned by railroad building in the Nest. He was not an engineer, but he had ideas of engineering work which he was destined to prove correct.. He introduced new ways of tunneling, but his plans had only one distinguishing feature-they were simply interesting as showing how such work could be done; they added nothing to the science, have never been used since his clay, and never will be used again. Engineers of repute ridiculed his proposition ; he was an Ishmael in the profession. But if engineers looked askance at him, he certainly returned their contempt in the heartiest fashion, and had no hesitancy about expressing his views of them individually and collectively. This worked to. his disadvantage when he afterward tried to raise the means to go on with the work. He found that the opinion of engineers was respected by financiers, and that money would not flow contrary to their advice. While his conception of large constructions was distinguishingly original, much more marked was his method of demonstrating the feasibility of, his schemes. In the present clays of great undertakings it is the custom to make the other man pay for the experiments. But the man from the West had other notions of how the thing ought to be done. Having wonderful confidence in his own ability and in his perception of the task before him, he used up all his own money before seeking outside assistance. By building several hundred,, feet of tunnel he proved the correctness of his theory, and the tunnel then dug forms a part of the present tube. The result-he failed to finish the tunnel. He was blind in

Mar 1, 1908

By J. E. Burke, A. M. Turkalo

IN 1923 Desch¹ pointed out that the grains in a metal which is anisotropic with respect to its thermal coefficient of expansion would contract differently upon cooling, and that the stresses developed might approximate the plastic strength of the metal. More recently Boas and Honeycombe2-5 studied the behavior of several metals upon thermal cycling and observed that the stresses developed in arlisotropic metals are great enough to produce slip lines in individual grains and a roughening of the specimen surface. This phenomenon they have named "thermal fatigue." The mechanism they propose involves essentially a kneading of the grains, the deformation being alternately in compression and tension in a given grain as the temperature is changed in one direction and then the other. The present work was undertaken to investigate the possibility that an additional mechanism might operate to produce plastic deformation during thermal cycling—a "thermal ratchet" that depends upon a combination of grain boundary flow to relax the stress that develops between differently oriented grains upon raising the temperature and transcrys-talline slip to relax the oppositely directed stress which develops on lowering the temperature. Thus, thermal cycling should produce a nonreversible distortion such that certain grains will change shape differently from their neighbors with a simultaneous displacement being produced at the grain boundary. Temperature Dependence of Grain Boundary and Grain Strength The critical resolved stress for the initiation of slip in metal grains is only mildly affected by temperature." For example, in cadmium it decreases from 0.15 to about 0.05 kg per sq mm when the temperature is increased from 20° to 458°K and further temperature increase causes little further decrease. On the other hand, the work of KG1 indicates that the grain boundaries behave in a viscous fashion that can be described8 by the expression: t = BVexp(Q/RT) [1] t is the shearing stress on the boundary; B, a constant; V, the flow rate at the boundary; Q, the activation energy for grain boundary flow; R, the gas law's constant; and T, the absolute temperature. Eq 1 indicates that the stress necessary to cause a given grain boundary flow rate, V, decreases rapidly with increasing temperature. The value of the constant B is such that at sufficiently low temperature and ordinary strain rates deformation will occur preferentially by slip rather than by grain boundary flow. There is considerable evidence to indicate Consider the bicrystal shown in Fig. 1. In grain 1 the slip plane lies 45 " to the boundary while in grain 2 the slip plane is 90" to the boundary. The coefficients of expansion of the grains in a direction parallel to the length of the crystal are a1 and a, with a, > a2 for the orientations shown. The sequence of events that can occur upon heating and cooling this specimen is illustrated schematically in Fig. 2. Initially there is assumed to be no stress in the specimen (A). Upon heating, grain 1 attempts to become longer than grain 2, but is constrained by grain 2. Thus grain 1 is loaded in compression and grain 2 is loaded in tension, and a shearing stress is present across the boundary (B). As the temperature is increased, the stress will build up, and finally grain 1 will be plastically deformed by slip, since the greater stress is resolved on its slip planes. Any further heating will result in more slip and the stress will remain constant until some temperature T* is reached where the stress can be relaxed by grain boundary flow.† At this relaxation temperature (C) a step will appear between grain 1 and grain 2. Further heating above T* will cause grain 1 to become relatively longer, but no stress will appear because the grain boundary is too weak to support the stress (D). Upon cooling again, at T* (E), the grain boundary will again be able to support a shearing stress, and upon cooling further, grain 1 will be loaded in tension and grain 2 in compression (F). When the decrease in temperature below T* is sufficient to impose the critical shear stress upon the slip plane of grain 1, it will be stretched by slip.

Jan 1, 1953

By A. S. Yue

The movphology of the Mg-32 wt pct Al eutectic has been studied as a function of freezing- rate and temperature gradient. At slow freezing rates a lamellar eutectic was formed; whereas, a rod-like eutectic was generated at fast rates. The inter-lamellar spacing increased as the freezing rate decreased in aggreement with theoretical predictions. Lamellar faults, morphologically similar to edge dislocation models in crystals, were responsible for the subgrain structures in the eutectic mixture. A linear increase in fault density with freezing rate was observed. Fault concentl-ations of the order of 10 per sq cm for a range of freezing rates from 0.6 to -3.0 x 10 cm per sec were estimated. The transformation from lamella?, to rod-like morphologies was determined experimentally to be dependent on the freezing rate and independent of the temperature gradient. Moreover, the number of rods formed per- unit cross-sectional area increased exponentiallv with increasing freezing rote. BRADY' and portevin2 classified eutectic structures into lamellar, rod-like, and globular according to the morphology of the solid phases present. Although this classification is quite descriptive, very little has been reported on the details of the mechanism by which the eutectic structures are formed. Recent work by Winegard, Majka, Thall, and chalmers3 and by chalmers4 on lamellar eutectic solidification suggest that the maximum thickness of the lamellae decreases with increasing rate of solidification due to inadequate time for lateral diffusion. scheilS and Tiller' have shown theoretically that the lamellar widths indeed depend on the solidification rate. However, there has been no experimental evidence to support the theory. Chilten and winegard7 have studied the interface morphology of a eutectic alloy of zone-refined lead and tin. They found that the lamellar width decreased as the freezing rate increased in agreement with the theoretical predictions of scheils and Tiller.' More recently, Kraft and Albright' have investigated the microstructures of the A1-CuA12 eutectic as a function of growth variables. They observed lamellar faults present in the lamellar eutectic, similar to edge dislocation models in crystals. Furthermore, Kraft and Albright reported that they could not designate which extra lamellar was responsible for the formation of a lamellar fault even under electron microscopic magnification. In this paper, the morphology of the Mg-A1 eutectic structure is described. The effects of freez- ing rate on the interlamellar spacing and on the lamellar fault density are presented in detail. The transformation from lamellar to rod-like eutectics is discussed in terms of the freezing rate and the temperature gradient. EXPERIMENTAL PROCEDURE The experimental details of alloy preparation, the decanting mechanism and the determinations of the freezing rate and the temperature gradient have been reported elsewhere. Measurements of plate-edge angles were made with a microscope. The true angles used to determine the interlamellar spacings were determined by a two surface analysis technique.'' Since the decanted interface structure does not represent the true eutectic morphology on the solid,g all measurements were made from an area in the solidified bar behind the interface. Measurements of the apparent interlamellar spacings between the two phases of the eutectic were made on a photographic negative by means of a calibrated magnifier. Each value listed in Table I represents the average of thirty measurements on one negative. In general, these measurements are approximately equal with an error of less than pct. The average rod diameter for each specimen was also measured on a magnified photomicrograph. Each value of the diameter represents the average of fifty measurements. RESULTS AND DISCUSSION The experimental observations and their discussion to be presented here are restricted to the morphology of the eutectic structure and to the effects of the freezing rate and the temperature gradient on the solidification of eutectics. INTERLAMELLAR SPACING It has been shown previouslyg that the micro-structure of the decanted interface and the longitudinal section of the Mg-A1 eutectic is characterized by the presence of both lamellar and rod-like morphologies. The lamellae become more regular as the freezing rate is decreased. A three-dimensional photomicrograph representing a perfect lamellar morphology is illustrated in Fig. 1. The lamellae of the top and longitudinal sections of the specimen are regularly spaced while those in the transverse section are not quite straight and parallel. Their parallelism is slightly distorted because fault lines producing a discontinuity are present. A method for calculating the interlamellar spacings A, is described in Appendix 1. The true

Jan 1, 1962

By D. W. Levinson, L. F. Mondolfo, N. A. Gjostein

MANY investigations are reported in the literature on the age hardening of Al-Mg-Zn alloys but most of them are concerned mainly with mechanical property changes. The present investigation was started to determine the structural changes in an AlMgZn alloy. The alloy composition was chosen in the existing phase diagram" so as to lie on the quasi-binary section Al-(AlZn)Mg Actually, it was found that the diagram as published was inexact at the lower temperatures and that the phase in equilibrium with aluminum at the lower temperatures is not the ternary compound. Technique The alloy used for the investigation was prepared from high purity materials and the resulting composition as determined by chemical and spectro-graphic analysis was: Zn, 6.17 pct; Mg, 2.13 pct; CU, 0.03 pct; Si, 0.009 pct; Fe, 0.005 pct; and the remainder, aluminum. An ingot -in. thick was cast, homogenized, hot and cold-rolled to strip 0.064-in. thick for dilato-metric and powder work, and to foil 0.005-in. thick for single crystal work. Solution treatment temperature for all specimens was 475°±5°C for periods of at least 1 hr, either in air furnaces or lead baths. Aging was done in oil or Pb-Bi baths controlled to within ±3°C. The aging was investigated at the following temperatures: room (30°), 130°, ZOO0, 260°, and 300°C. For the dilatometric study, the length changes were measured continuously, at temperature, using strips of alloy 10 in. long, shaped as channels to eliminate undesirable deflection due to bending. To compensate for thermal expansion and contraction due to the variations in the temperature of the aging baths, the dilatometers were built of the same alloy as the one being tested, with the same shape and size, but with material fully annealed. Gages on which 0.0005 in. could be read and 0.0001 in. estimated were used to measure the dilation. Length changes were also measured at room temperature. Strips approximately 10 in. long were solution-treated, quenched, and measured in a supermicrome-ter in which 0.0001 in. could be read and 0.00001 in. estimated. The specimens were immediately aged for a given time, remeasured, and then the cycle was repeated, including the solution treatment. The error of measurement with this technique was somewhat larger, but the results confirmed those obtained by continuous measurements. The sheet used for the dilatometric work was checked to determine grain orientation. Both X-rays and etching methods revealed a rather coarse grain size but only a negligible amount of preferred orientation. Thus, volume changes calculated from length changes are not invalidated by preferential orientation effects. Pieces of the sheet used for the dilatometric work were also used for the metal -lographic work. Filings for the powder X-ray study were produced from a homogenized piece of sheet. These filings were magnetically purged of iron, screened to 200 mesh, sealed in a Pyrex tube containing an argon atmosphere, and solution-treated. When quenching, the glass tube was broken, so that the powder dropped directly into cold water. After drying with alcohol, the powder was sealed into capillary tubes containing an argon atmosphere and then aged for the required times. In spite of all these precautions the three strongest lines of a( Al2o) appeared in all patterns, and were used as internal standards. By the use of these standards, accurate corrections for film shrinkage were obtained. For the back reflection patterns, annealed nickel powder was mixed with the specimen to act as internal standard. A preliminary investigation was made in small (57.3 mm diam) powder cameras. From these patterns the changes which took place in the solid-

Jan 1, 1957

By S. N. Singh, M. C. Flemings

Results are presented of a study on the combined influences of ingot dendrite am spacing and thermo-mechanical treatments on the fracture behavior and mechanical properties of high purity 7075 aluminum alloy. The most important single variable influencing mechanical properties was found to be undissolved alloy second Phase (microsegregation inherited from the original ingot). Ultimate and yield strengths were found to increase linearly with decreasing amount of alloy second phase while ductility increased markedly. At low amounts of second phase, transverse properties were approximately equal to longitudinal properties. In tensile testing, microcracks and holes were invariably found to originate in or around second phase particles. Fracture occurred both by propagation of cracks and coalescence of holes, depending on the distribution and amount of second phase. IN most commercial wrought alloys, second phase particles are present that are inherited from the original cast ingot. These include, for example, non-equilibrium alloy second phases such as CuAl2 and impurity second phases such as FeA13 and Cr2A1, in aluminum alloys. A previous paper1 has dealt with the morphology of these second phases in cast and wrought aluminum 7075 alloy, and with their behavior during various thermomechanical treatments. In this paper we discuss the influence of the particles on mechanical properties and fracture behavior of the alloy. Previous experimental work indicating a direct and major effect of second phase particles on mechanical properties (especially on ductility) includes the work of Edelson and Baldwin on pure copper.' Also relevant are the many studies demonstrating the important effect of nonmetallic inclusions on the fracture of. steel.3'4 Work on aluminum includes that of Antes, Lipson, and Rosenthal5 who showed that a dramatic improvement in ductility of wrought aluminum alloys of the 7000 series is achieved by eliminating second phases. It now seems well established that included second phases play a dominant role in controlling ductility (as measured, for example, by reduction in area in a tensile test) of a variety of materials. There is, therefore, considerable current interest in the mechanisms by which second phase particles affect ductile fracture. Experiments done by various workers have shown that second phase particles or discontinuities in the microstructure are potential sites for nuclea-tion of microcracks and of holes,6-l3 which then grow and cause premature fracture and the loss of ductility. Theoretical attempts have been made to explain the observed phenomena; most are able to explain observations qualitatively, but lack quantitative agreement. Much experimental work needs to be done to aid extension of theoretical models. A recent review article by Rosenfield summarizes work in this general area.14 PROCEDURE Material used in the previously described study on solution kinetics of cast and wrought 7075 alloy1 was also used in this study. Procedures for ingot casting, solution treating, and working were described in detail in that paper. Test bars were obtained for material of 76 initial dendrite arm spacing (11/2 in. from the ingot base) and 95 µ initial dendrite arm spacing (51/2 in. from the ingot base) for the following thermomechanical treatments (solution temperature 860°F; reduction by cold rolling). a) Solution treated 12 hr, reduced 2/1, 4/1, and 16/1. b) Solution treated 12 hr, reduced 16/1, solution treated approximately 5 hr after reduction. c) Same as a) except solution treated 24 hr prior to reduction. d) Same as b) except solution treated 24 hr prior to reduction. e) Same as d) except solution treated 20 hr after reduction. Test bars were taken both longitudinally and transverse to the rolling direction. Transverse properties are in the long transverse direction; since the final product was sheet (0.030 in. thick), properties in the short transverse direction could not be obtained. Test bars were flat specimens, of gage cross section1/-| in. by 0.030 in. and 1/2 in. gage length. After machining the test bars, they were given an additional 1/2 hr solution treatment of 860°F and aged 24 hr at 250°F. Three bars were tested for each location and thermomechanical treatment, after rejection of mechanically flawed bars. The average results of these three bars are reported. Elongation was measured using a $ in. extensometer and reduction in area was determined using a profilometer to measure the area after fracture. INFLUENCE OF THERMOMECHANICAL TREATMENTS AND SECOND PHASE ON MECHANICAL PROPERTIES Results of mechanical testing are presented in Figs. 1 to 4 and in tabular form in the Appendix. A general conclusion from results obtained is that details of the thermomechanical treatments studied were important only insofar as they influenced the amount of residual second phase. Figs. 1 and 4 show the longitudinal properties obtained (regardless of thermomechanical

Jan 1, 1970

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

0. C. Ralston and F. Fraas—Dr. Sun and associates have presented an interesting paper not all of which is comprehended by us. The data assembled measure the deflections of particles in an electrostatic field as a function of a number of independent variables and some dependent variables that are not sharply differentiated. These data are all based on a Johnson type machine of definite, well-described geometry, something not often done in electrostatic separation literature. One new fact brought out by this technique is the effect of coal dust on admixed pyrite and quartz. The effects are opposite in character, as should be expected and we do not agree with the authors that these effects are negligible. Fraas' also used a multiple cell "distribution analyzer" and gives in fig. 5 of his paper a straight line plot with no humps or curves. This is not necessarily at variance with Sun's results because Fraas used a larger gap between electrodes and had no evidence of particles adhering to or dropping off the charged electrode. The section of Sun's paper on effect of surface conductivity contains a speculation that the dielectric constant "represents more or less the electrical conductance of the bulk body instead of the surface of the mineral particles." A simple picture of the meaning of the dielectric constant is that it is the specific inductive capacity of a dielectric when used as the dielectric between the plates of a condenser. It is at once evident that the above speculation confuses capacity with conductance—two definitely independent variables. We ask the authors to state in what group or subdivision their garnet belongs; what method and units were used in calculating the data of col. A, table I and their meaning; what was the temperature of the carrier roll and, finally, has any effort been made to investigate the effects of particle shape on distribution in the electrostatic field? S. B. Hudson—I have read this article with great interest. We have been engaged in research work on the principles of electrostatic separation in this laboratory for some time now, and our findings agree with those of the authors in many respects. The article shows evidence of careful and valuable research in the field of electrostatic separation. A "distribution analyser," very similar to that described in an earlier article by one of the authors," was incorporated in an inclined plate-type electrostatic separator designed and built in the Melbourne University laboratory in 1948 for investigation purposes.22 The actual splitting edges were machined from y! in. per-spex, and the paper hoppers were supported on linen thread immediately below the perspex dividers. These dividers fitted into machined slots in a framework to give accurate Yz-in. spacings. The hoppers (staggered) fed directly into a rack of test tubes, which is supported on a vertical pantograph arrangement. The rack was positioned with guides on the horizontal pantograph stand, and this ensured positive alignment when replacing the rack after making weighings. In later work, when much heavier feed rates were used, of the order of 30 to 40 Ib per in. per hr a rack fitted with rectangular metal containers and similarly aligned was used. Some work was done here on comparing the distributions of minerals when passed separately and when passed as a mixture, and it was found that there was quite an appreciable difference in the two results.= However, in our separator the particles do not pass down the plate in a single layer, and this difference is probably caused by collisions of one mineral particles with the other mineral particles. In most of the investigational work here, the change of the center point of the distribution is measured to establish the effect of a variable, such as voltage. Two minerals (zircon and rutile) have been studied rather exhaustively, and it was found that their distributions are very nearly normal. Owing to the sharpness of the distribution curves, the usual method of obtaining the mean or median was inaccurate, and was not used; instead the mean (also the median), calculated on the assumption of a normal distribution, was used to locate the center point of each distribution and proved satisfactory. The effect of polarity becomes very apparent in the plate-type separator where frictional charges play a very important part when using highly resistive minerals such as zircon. With rutile, a comparatively conductive mineral, polarity of the electrode has little effect. On the other hand, the magnitude of the voltage has a far greater effect on conductive than on resistive minerals. Shiou-Chuan Sun (authors' reply)—Thanks are extended to Drs. Ralston and Fraas for their keen interest in this paper. Their questions concerning coal dust,

Jan 1, 1951