Search Documents

By Rossiter W. Raymond

(Read at the Amenia Meeting, October, 1877.) THE term "pipe-vein" has recently been applied in this country to certain deposits of lead ore in magnesian limestone. The use of the term has been twofold. It has been revived as a term found in textbooks on mineral veins, with the implied or declared assertion that the ore-deposits thus named in this country are similar to those which have borne the title abroad. It has also been advanced as an appropriate name for a new class of deposits, even if such a class had not previously been recognized. In either case, the assumption is that pipe-veins form a group or class by themselves, and are not merely interior and subordinate features in larger deposits. The peculiar mining law of the United States, which regards " the vein," whatever that may be, as the basis of title, lends a special interest to these claims. But the object of this paper is rather to discuss the subject from the standpoint of geology and technical literature. I shall briefly answer two questions : (1) What are pipe-veins as described in technical literature? and (2) Is the name appropriate or necessary for a new class of deposits ? The term "pipe-ore," as applied, for instance, to irregular, cylin-

Jan 1, 1878

By Robert F. Shurtz, William J. Verner

Three basic questions must be answered by an engineer performing an economic analysis of a mineral property: (1) How much can the company afford to pay for the property; (2) At what rate should the property be mined; (3) What will be the return on the investment. These questions often defy reasonable analysis, because at the point in time at which they must be answered little may be known about the grade of ore and the reserve tonnage. The purpose of this report is twofold. First, to derive a method of determining purchase price, rate of production and return on investment which is valid under varying conditions of ore grade and tonnage reserve; and, second, to apply this method to the Margay deposit in an attempt to evaluate it as a business enterprise. This is an actual economic analysis of an existing nickel-copper deposit fictitiously named the Margay. It was carried out for a mining corporation and proved to be the determining factor in the subsequent purchase and development of the property. All data referring to costs, quality and quantity of ore, etc., are accurate and truly represented. Prices used are obsolete but the method is not dependent on those variables. Basic assumptions for the analysis are given in Table I, page 71.

Jan 11, 1966

By Sharon Brady, Catherine O’Donoghue, John V. Beall, Paul C. Merritt

Between 1950 and 1965, more than 80% of all phosphate rock produced in the world each year was used as fertilizer, either directly applied to the soil or processed into mixed chemical fertilizers. Of the potassium salts produced, 95% followed suit. A variety of uses in industrial chemicals and consumer products absorbed the remaining percentage of each. Future trends in these two commodities will be dominated by what happens to the fertilizer market. Farming is much the same as mining the soil. Plants remove the minerals little by little. Phosphate and potash comprise two of the three primary nutrients removed in this way, the third being nitrogen. Phosphate stimulates early root formation and growth, whereas potash is a salt necessary to root strength.

Jan 10, 1966

By Ian Campbell

THE year 1952 was marked by several new alltime highs in industrial mineral production; by an easing of the critical situation with respect such minerals as fluorspar and sulphur; by important production of asbestos, lithium, and rare earths; by the perfecting of new products which will place new demands upon industrial mineral supplies, such as "Fiberfrax", and the finding of new uses for old minerals, such as wollastonite; by continuation of basic and applied research; and publication of a notable study of the national mineral economy, viz., the "Paley Report".

Jan 2, 1953

By D. Y. Geng, S. S. Peng

Surface subsidence of two longwall panels, one with a private residence and the other with an arch bridge, was monitored over a period of 1 to 1' ½ years. Surface subsidence data were analyzed in terms of zone of advance influence and delay angle of maximum subsidence velocity. The variational characteristics of both features coincide with the periodic weighting at the advancing longwall face. Surface heaving in the subsidence process can also be attributed to periodic weighting. It was found that residential damages occurred when subsidence velocity exceeded 4.5 mm/day (0.15 ft/day). The effects of locating structures on the panel center and near the gob edges are illustrated. The effect of mining on ground water was also discussed. Finally, methods of reducing structural damages are recommended.

Jan 1, 1984

By B. G. Langston, R. D. MacDonald, F. M. Stephens

WITH the development of uranium ores that contain substantial amounts of acid-consuming compounds, the alkaline leach has become an attractive method for extraction. Considerable work has been done on both atmospheric and pressure-leaching with aqueous solutions of sodium carbonate and sodium bicarbonate as the lixiviants.1,2,3 For the treatment of uranium-bearing limestones and other high-lime (CaO) ores, the sodium carbonate leach has proven attractive because it avoids the high reagent consumption incurred by the reaction of sulfuric acid with lime. In addition, the corrosion problems with sodium carbonate are negligible as compared with those encountered in the acid-leach system. The sodium carbonate leach, however, does not yield as high an extraction of the uranium as the acid leach and is not attractive for economic reasons when treating ores that are high in sulfates or sulfides.

Jan 9, 1957

By S. Y. Han

INTRODUCTION More than 97% of the total uranium production of the United States comes from sedimentary deposits (1). These sandstone deposits were formed by reduction of migrating uranium-bearing solutions from volcanic silicate rock sources. Such deposits occur in two major forms, either as relatively flat, lens-like deposits or as crescent- shaped roll front deposits. The lens-like deposits are found as discrete masses enclosed in reduced sandstone which is generally surrounded by oxidized sandstone. The roll front deposits are found along crescent-shaped interfaces between reduced and oxidized sands tone (2). In-situ mining of selected sedimentary deposits has proven to be a viable method of extraction and competitive with conventional mining for relatively deep low-grade ores (2). In in-situ leaching, uranium is recovered by drilling injection and collection wells in the ore body, pumping a suitable lixiviant to dissolve the mineral, extracting uranium from the pregnant solution by ion exchange, and finally regenerating and recycling the lixiviant. Even though there is increasing interest and practice in developing the in-situ technique for obtaining uranium values from deeper, lower-grade reserves, there is a lack of knowledge of the basic leaching kinetics and combined transport processes. In-situ leaching operations, in general, appear attractive for the following three general types of deposits (2): (1) low-grade surface dumps or deposits which lie above the natural water table,

Jan 1, 1983

By Carolyn Barnes

The Offshore Technology Conference, the world's largest technical conference and exhibition on the development of offshore resources and protection of the ocean environment, is sponsored annually in Houston, Texas, by 12 international engineering and scientific societies. This year's OTC, the seventh, will be held May 5-8 at the Astrodomain, and will be the largest in its history. The technical program for the first meeting in 1969 consisted of 100 papers, an exhibit display of 380 booths, and an attendance of 4300. This year. 280 technical papers are to be presented, and more than 2800 exhibit booths, representing some 1200 companies and nine countries, will be on display for an anticipated audience of 40,000.

Jan 4, 1975

By George Evans

DURING the past ten or twelve years, the average reader of newspaper and magazine articles has been led to believe that enormous deposits of high-grade coal exist in the northland and that these can be mined for practically nothing. But much of the reputed glitter and attractiveness of Alaskan coals disappears when viewed at close range. Many areas of coal-bearing rocks are widely distributed geographically from Cape Lisburne, on Bering Sea, to Admiralty Island south of Juneau. Bituminous coal is found at Cape Lisburne, on the Bering Sea, at Five Finger Rapids on the upper Yukon, and at Herendeen Bay and Chignik Bay; lignite is found on the Kobuck River, along the Yukon River from points near the mouth to Tonakat, near Rampart, at Dawson, on the east shore of Cook Inlet, and in the Tanana Valley, 50 mi. south of Nenana. The Susitna and Matanuska Valleys contain coal ranging from lignite to anthracite, and in the Bering Lake district, there are coals ranging from semi-bituminous to anthracite. No effort will be made to describe all of these fields, but the writer wile confine himself to the four principal fields, namely, the Nenana field, in. the interior of Alaska, tributary to the Fairbanks district; the Matanuska, field, in the Matanuska Valley; the Kachemak Bay field on the east shore of Cook Inlet; and the Bering River field, east of the mouth of Copper River.

Jan 2, 1921

By Robert Stefanko

Roof bolting in coal mines has progressed very rapidly in the last decade, and today this method of support is in general use. There are many theories concerning the functions of roof bolts, but the importance of beam building is indisputable. Proper tension in the bolts minimizes shearing along bedding planes and creates a thick, competent beam from individually weak layers. Bolting must be accomplished immediately upon exposure of the roof, and bolt tension must be maintained if roof failure is to be prevented. Seams are being mined today with roof bolt support where conventional timbering was not effective1. The widespread use of continuous mining equipment was made possible by roof bolts which permit long supported spans free of obstructions.2 Since adequate anchorage is the key to successful bolting, better methods for determining the efficiency of anchorage are continually being sought. Attempts have been made to measure bolt loads, thus assessing anchorage efficiency by employing sensing devices between the bolt head and roof. 3,4,5 None of the techniques appears to be very accurate, and all have at least one serious deficiency.

Jan 5, 1962

By S. J. McCarroll

THE Three Kids mine, some six miles east of Henderson, Nev., is in a typical southwest desert area, with high dry summer heat and cool to cold winter seasons. The manganese deposit was located during World War I.1 During this period 15,000 to 20,000 tons of ore assaying up to 41 pct manganese were shipped. Interest in the deposit was not revived until the middle thirties, when experiments on the ore were initiated. Test work indicated possible recovery of only 70 pct by flotation, but in 1941 additional work was done at the Boulder City pilot plant of the U. S. Bureau of Mines and also by M. A. Hanna Co. As a result, the Manganese Ore Co. was formed and a plant utilizing the SO, process was constructed. Numerous operation difficulties ensued, and the plant was closed when the manganese situation in the country eased.

Jan 3, 1954

By Porter W. Shimer

Ox completing the filtration of a solution of pig-iron in hydrochloric acid, and after apparently everything had been transferred to the paper, a minute residue was observed remaining in the angle of the beaker in which the solution had been made. This residue had a steel-gray color and metallic luster and was hard and gritty when touched with a glass rod. Placed under a microscope and magnified 400 diameters, the substance was found to be made up almost entirely of opaque cubical crystals with some fragments having the same color and luster as the cubes. The appearance was strikingly like that of a collection of crystals of iron pyrites. The amount of material obtained from ten to twenty grams of borings by solution in dilute hydrochloric acid, and careful decantation from graphite, was barely sufficient for a microscopic slide. A qualitative test of the minute amount of material obtained in this way, showed the presence of considerable titanium. After many fruitless trials by decantation and other methods, sufficient material for quantitative analysis was finally obtained in the following manner: Two hundred and fifty grams of the coarsest possible borings were dissolved in seven liters of hydrochloric acid of sp. gr. 1.03. A solution by the aid of heat took four to five hours. It was allowed to settle, and the clear solution poured off. Great care was taken that none of the material which had settled to the bottom was lost. The graphitic residue was then completely transferred upon fine bolting-cloth, previously Stretched and fastened over the top of a beaker. All graphitic lumps were broken up by the finger while

Jan 1, 1887

By L. F. Mondolfo, W. T. Collins

A study of the relationship between undercooling for nucleation and structure in Sn-Cu alloys with 0.1 to 5 pct Cu has shown that in hypereutectic allojls the halo of tin that surrounds the primary crystals of Cu3Sn5 is larger, the larger the undercooling for nucleation o,f the tin. This increase of halo size results in a decrease of coupled eutectic, and, in alloys far from the eulectic composition, may produce its complete disappeavance, with the formation of a divorced eutectic structure. This was confirnred by the excrrnination of other alloys in which divorced eutectic slructuves are formed, and leads to the conclusion that they ave only an extrenle case of halo forrtzalion , which results when the two phases freeze one at a time and solidification of the first is completed Defove the second starts. It was also found that under proper conditions of nucleation all types of eutectic structures can be formed in the sartte system , and therefore divorced eutectics, like normal and anomalous, are not characteristic of the syslett~, but are mainly controlled by nucleatiorz. Dizlovced eutectics are formed when the phase that tutcleates the eulectic vequires a large undevcooling for ils nucleation and when the cotnpositiorz of the alloy is far from the eutectic., on the side of the primary phase that does not nucleate the other phase. It is recommended that the tevm "divorced" be used in preference to degenerate because it is more desct-iptice of the morphology and mode of forinalion of the structures. ThE variety of structures found in eutectic alloys has been extensively investigated and classified. The most accepted classification is the one by ~cheil,' in which three different types of eutectic were distinguished: 1) normal, 2) anomalous, 3) degenerate (divorced). ATornlal eutectics are typified by the simultaneous growth of the two phases ("coupling") by which the two phases appear as interpenetrating crystals. The presence of a crystallization front, in which the two phases grow side by side, creates the eutectic grains, with the boundaries where the fronts meet. The presence of eutectic grains is the .distinguishing feature of a normal eutectic, according to Scheil. Straumanis and Brakss2 examined the Cd-Zn system and showed that there was a crystallographic relationship between the phases. Later, others4 also investigated additional systems and found definite crystallographic relationships in the coupled eutectics. The anornalous eutectic shows much less coupling than the normal; the two phases are intimately mixed but 'grow without a uniform crystallization front—a consistent crystallographic relationship— and the eutectic grain is conspicuously absent. As in the normal eutectics faster rates of growth result in a finer structure, but there is not the typical uniform spacing of normal eutectics. The degenerate eutectic shows no coupling; in fact the two phases attempt to minimize their area of contact and to form separate crystals. It has been suggested5" that slow cooling may favor this type of structure. Scheil believes that normal eutectics are formed when the two solid phases are present in more or less equal proportions, whereas both anomalous and degenerate eutectics form when one of the phases is present only in small amounts. spengler7 extended much farther this qualitative relationship between the eutectic type and the ratio of the two phases, and added a relationship to the melting point of the constituents. On this basis he proposed two equations for determining into which of Scheil's classifications an alloy belongs. The first equation is: where TI is the melting temperature of the lower-melting component, Tp of the higher-melting component, and Te the eutectic temperature. The second equations is: where is the volume percent of the lower-melting phase and $2 of the higher-melting phase at the eutectic composition. If 0 and/or 4 are in the range 0.1 to 1, a normal eutectic is formed; if in the range 0.01 to 0.1, anomalous; if less than 0.01, degenerate. Although the examples given by Spengler show a good agreement with the formulas, chadwick found that the Zn-Sn eutectic is normal to all growth rates, even though the volume ratio is 12/1, and Davies9 reports that the A1-AlgCo2 eutectic is normal, with a volume ratio of more than 30/1. Many more discrepancies of this type can also be found. Neither Scheil nor most of the other investigators have considered nucleation as a factor in the formation of divorced eutectics. Daviesg states that divorced eutectics form when neither phase acts as

Jan 1, 1965

By J. C. Savins

The practical analysis of the hydrodynamics of the wellbore has long been a subject of interest to engineers. This paper presents a simplified solution to the problem of computing the pressure drop for the flow of drilling mud in the annulus of the wellbore. This solution is, however, an exact and rigorous solution under the assumptions which have been imposed. These assumptions are that the drilling fluid is a Bingham plastic fluid* and that the annulus is formed by two concentric, stationary, cylindrical pipes. It is further assumed that the fluid is incompressible and that its motion is isothermal and in a steady state. This problem under the same assumptions has been attacked by previous authors. Beck, Nuss and Dunn' proposed that the equation for the flow of a Bingham plastic fluid in a cylindrical pipe could be applied to an annulus if the pipe radius were replaced in the equation by the hydraulic radius. This equation, known as the Buckingham-Reiner equation' (see Appendix 1), was also used in an approximate form. Van Olphen pointed out that even for a simple or Newtonian- fluid the pipe equation (Poiseuille's law) could not be converted to the Lamb equation escriptive of flow in an annulus (see Appendix 1) by using the hydraulic radius. Van Olphen further attempted to give a solution for the annular flow of a Bingham plastic fluid by introducing approximations similar to those which have been used in the case of the Buckingham-Reiner equation. Other attempts to provide approximate or exact solutions have been made by Grodde' and by Mori and Ototakeq. The present authors some years ago in unpublished work derived the correct expressions relating the pressure drop and flow rate for this problem. It was found that the solution consisted of two simultaneous equations, one of which contained a logarithmic term. Thus, obtaining numerical results for any particular case of interest involves very tedious trial-and-error computations. Very recently Laird presented the correct derivation of the two equations which are given in full detail in Appendix 1. In order to reduce the amount of calculation time which would be involved in providing a complete tabular or graphical solution to the problem, a high-speed electronic digital computer has been utilized. For this purpose the two simultaneous equations were transformed into more compact expressions by introducing reduced variables. These expressions are given in the following theoretical section. A similar procedure in this problem has been developed by Fredrickson and Bird1" Their tabular results, however, are very incomplete in the range of practical interest for problems of wellbore hydrodynamics. We have furthermore been able to express our graphical results in terms of convenient and familiar dimensionless groups. THEORETICAL DEVELOPMENT Use of Reduced Variables In terms of reduced variables the two simultaneous equations just discussed take the following form, The reduced variables q, x, a and z are defined in terms of the various measured quantities, where Q is volumetric flow rate, AP/L is pressure gradient, Dl is OD of inner pipe, D, is ID of outer pipe, is plastic viscosity, and is yield point. Thus, we have a dimensionless volume flux, a dimensionless reciprocal pressure gradient, and the ratio of the pipe diameters Before introducing the fourth reduced variable, z, it is of interest to consider the physical significance of the parameter x. As may 'be seen from the velocity profile of Fig. 1 the Bingham plastic fluid has the interesting property that a portion of the stream flows at a uniform velocity without shearing action. This section of the stream is situated approximately in the center of the conduit and is known as the "plug flow" region. Its existence is due to the fact that the shearing stresses within the region do not exceed the yield point, which is one of the two flow properties characterizing the fluid. The parameter x then turns out to be the ratio of the

By R. D. Daniels, T. G. Oakwood

A study was made of the effects of small quantities of hydrogen on the mechanical properties of colum-bium. Tensile specimens, hydrogenated to concentrations of 20 to 200 ppm, were tested at temperatures of 300°, 191°, and 77°K. Although hydrogen was found to have little effect on the strength of columbium, the ductility of Cb-H alloys was found to be quite sensitive to both hydrogen concentration and temperature. At 300°K, an abrupt loss in ductility occurred at a critical hydrogen concentration, although some ductility was observed beyond the tolerance limit. A similar result was found at a lower hydrogen concentration at 191°K. At 77°K, however, a more gradual loss in ductility with increasing hydrogen concentration was observed. Hydrogenated columbium was thus observed to undergo a ductile-brittle-ductile transition. Metallographic examination of fractured specimens revealed extensive porosity at both 77° and300°K which was a distinct function of hydrogen content. At 191°K, although some secondary cracking was noted, the amount of observed porosity was minimal. These observations are interpreted in terms of hydrogen solubility and mobility as a function of temperature and in the role of hydrogen in promoting growth of microcracks. lHE effect of hydrogen on the mechanical properties of the refractory metals is not, at present, completely understood. A number of studies have shown these materials to be susceptible to hydrogen embrittlement. Roberts and Rogers1 have found that vanadium can be embrittled by hydrogen. It was further demonstrated that fracture undergoes a ductile-brittle-ductile transition as the temperature is lowered from 150° to -196°C; i.e., there is a ductility minimum observed at a certain temperature. The ductility is increased by either raising or lowering the temperature from this point. A more complete study by Eustice and Carlson2 on vanadium containing 10 to 800 ppm placed the ductility minimum at about -100°C with variations reportedly due to hydrogen content and strain rate. Ductility minima have also been found at certain temperatures for tantalum containing 7 ppm H3 and 140 ppm H.4 At hydrogen concentrations above 270 ppm, however, the ductility return at low temperatures was considerably reduced.4 In the case of columbium, some disagreement exists in the literature. Eustice and Carlson,5 Wilcox et al.,6 and Imgram et al.4 failed to find a ductility minimum although a composition-dependent ductile-brittle transition was observed. Hydrogen concentrations in these investigations were 20 ppm,5 1 to 30 ppm,6 and 200 to 390 ppm.4 However, Wood and Daniels7 observed a rather pronounced ductility minimum at hydrogen contents ranging from 19 to 252 ppm. Those theories of hydrogen embrittlement involving the precipitation of diatomic hydrogen which have been applies to ferrous metals8-12 do not seem to be applicable to the case of columbium and other exothermic occluders. Such theories propose that extensive crack formation and propagation occurs by the precipitation and expansion of diatomic hydrogen at internal voids and microcracks. However, photomicrographs of hydrogenated columbium do not show any evidence of damage introduced by the sorption and precipitation of diatomic hydrogen; rather, at high hydrogen concentrations, a hydrogen-rich second phase is precipitated.13'14 In addition, a number of these theories require the development of high hydrogen pressures at voids in the structure.8'10'12 This does not appear to be feasible in the concentration ranges discussed in the aforementioned paragraphs. The possible interaction of atomic hydrogen with microcracks resulting from dislocation pile-ups15,16 remains in doubt since pile-ups have not been observed in bcc metals17 including columbium.18 Wood and Daniels7 have put forth the possibility that a hydride precipitation could be responsible for crack nucleation in columbium. Work by Longson19 has shown that hydrogen embrittlement of columbium parallels the bulk solubility limit; i.e., as the solubility increases, for instance with temperature, the amount of hydrogen necessary to cause embrittlement also increases. Although a hydride precipitation appears attractive as a means of nucleating microcracks in columbium, what require more intensive study are the low-temperature anomalies which have been observed, i.e., the ductile-brittle-d'ictile transition characteristics. Also, the hydrogen concentrations where embrittlement occurs are often below the bulk solubility limits determined by Albrecht et al.13,14 and Walter and Chandler.20 This work is an attempt to determine more definitively the effects of concentration and temperature on the mechanical properties of dilute Cb-H alloys. EXPERIMENTAL PROCEDURE Ultrahigh-purity columbium rods, obtained from the Wah Chang Corp., were cold-reduced by rotary swaging. A chemical analysis is given in Table I. The material was cut into cylindrical blanks 1.50 ±0.005 in. long. Individual specimens were either given a stress relief anneal at 750°C or recrystal-lized at 1200°C. Resulting microstructures were either a "bamboo" structure characteristic of a wrought material or a recrystallized structure with a grain diameter of approximately 100 n. All heat treatments were carried out in a vacuum of 10-5 Torr or less.

Jan 1, 1969

By F. H. Vitovec, D. W. Hoeppner

Pusk-pull fatigue tests were conducted on copper tricrystals of 99.988 pct purity to ascertain the role of grain boundaries in the initiation and propagation of fatigue cracks. Significant differences in behavior were found for specimens which possessed different transverse-boundary misorientation. In speciwens with low boundary angles cracks initiated within the transverse boundary, while higher angles led to transcrystalline fatigue failure. It is suggested that at low angular misorientation moving dislocations may interact with dislocations of the boundary or dislocations present in adjacent pains on favorably oriented glide planes, thus initiating a fatigue crack. MANY fatigue studies have been concerned with fatigue-crack initiation within grains and the mechanism causing initiation and propagation1-3 Although the initiation of fatigue cracks in or near grain boundaries of pure metals has been observed and reported in the literature, the mechanism of this phenomenon has received little attention.4"11 EXPERIMENTAL PROGRAM Testing Procedure. To investigate the role of grain boundaries regarding initiation and propagation of fatigue cracks, copper tricrystals were tested in push-pull. Axial-stress tests were used to avoid the stress gradients introduced by stressing of some other nature. Copper was selected as the most suitable test material since extensive work has been done on the formation of fatigue-induced slip in copper. Tricrystal specimens were used to provide a grain boundary geometry with one boundary transverse to the principal stress axis and one or more boundaries nearly coincident with the direction of maximum resolved shear stress. The boundary energy and the slip characteristics in the vicinity of the transverse boundary depend on the relative orientations of grains across the boundary. Testing was done at room temperature, at a frequency of 700 cpm, in an atmosphere of either air or argon. It is known that the incidence of grain boundary cracking increases with increasing temperature and decreasing frequency.4 The fatigue machine applied a uniaxial tension-compression load to the specimen by a flat spring which was actuated by an adjustable eccentric. Use was made of an adjustable head and a load cell which had strain gages mounted at 120-deg intervals around its periphery, thus providing a means for eliminating any detectable superimposed bending moment. A clip gage was mounted between the gripping heads to record the cyclic strain amplitude applied to the specimen. Each specimen's hysteresis characteristics were recorded by supplying the load and strain signals to an oscilloscope. Microstructural changes were observed and recorded with an optical microscope which was mounted on the fatigue machine. Immediately prior to insertion in the machine, each specimen was chemically polished. Extreme care was exercised while inserting the specimen in the test machine to avoid either bending the specimen or introducing a mean load. Each specimen was stressed in the tensile direction first and subsequently the load was reversed. Specimen Preparation. Tricrystal fatigue specimens of 99.988 pct Cu were grown from the melt using a modified Bridgman technique. Ingots about 1 in. high were grown to the configuration shown in Fig. 1. Upon sectioning the resultant ingot, several specimens were provided with an identical shape and grain boundary orientation. Except for plane sectioning and final polishing, this method eliminated machining the specimens. The apparatus used for growing the tricrystals is shown in Fig. 2. A spectrographically pure graphite mold, Fig. 3, was inserted in a vycor tube which was mounted on a vertical zone-refining table. Prior to insertion in the tube the mold was assembled as follows. The insert and graphite rods were fixed in position in the mold. The copper was then placed in the mold and the entire mold assembly was positioned in the vycor tube, Fig. 2. At this point the tube was sealed, evacuated, purged with helium gas, and finally placed under a slightly positive helium pressure. The heating coil was then adjusted to melt the copper charge, after which it was raised at a speed of 4 in. per hr. It is also possible to use

Jan 1, 1964

By William D. Klopp, Joseph R. Stephens

A substantial reduction in the 300°F ductile-to-brittle transition temperature for unalloyed chromium was achieved in alloys from systems which resemble the Cr-Re system. These alloy systems include Cr-Ru, Cr-Co, and Cr-Fe. Transition temperatures ranged from -300° F for Cr-35 at. pct Re to -75°F for 0-50 at. pct Fe. The ductile alloys have high grain gvowth rates at elevated temperatures. Also, Cr-24 at. pct Ru exhibited enhanced tensile ductility at elevated temperatures, characteristic of superplas-ticity. It is concluded that phase relations play an importarlt role in the rhenium ductilizing effect. The ductile alloys have compositions near the solubility limit in systems with a high terminal solubility and which contain an intermediate o phase. The importance of enhanced high-temperature ductility to the rhenium ductilizing effect is not well understood although both may have common basic features. CHROMIUM alloys are currently being investigated for advanced air-breathing engine applications, primarily as turbine buckets and/or stator vanes. The inherent advantages of chromium as a high-temperature structural material are well-known1 and include its high melting point relative to superalloys, moderately high modulus of elasticity, low density, good thermal shock resistance, and superior oxidation resistance as compared to the other refractory metals. Additionally, it is capable of being strengthened by conventional alloying techniques. The major disadvantage of chromium is its poor ductility at ambient temperatures, a problem which it shares with the other two Group VI-A metals, molybdenum and tungsten. For chromium, the problem is further amplified by its susceptibility to nitrogen em-brittlement during high-temperature air exposure. In cases of severe nitrogen embrittlement, the ductile-to-brittle transition temperature might exceed the steady-state operating temperature of the component. The low ductility of chromium would make stator vanes and turbine buckets prone to foreign object damage. The present work was directed towards improvement of the ductility of chromium through alloying, with the anticipation that any improvements so obtained might be additive to strengthening improvements achieved through different types of alloying. The alloying additions for ductility were selected on the basis of the similarity of their phase relations with chromium to that of Cr-Re. The reduction in the ductile-to-brittle transition temperatures of the Group VI-A metals as a result of alloying with 25 to 35 pct Re is well established.a4 the temperature range -300" to 750° F. This phenomenon is commonly referred to as the &apos;<rhenium ductilizing effect"; this term is also used to describe systems in which the ductilizing element is not rhenium. Other alloy systems which have recently been shown to exhibit the rhenium ductilizing effect include Cr-Co and c-Ru.= In order to explore the generality of this effect, alloys were selected from systems having phase relations similar to that of Cr-Re, primarily a high solubility in chromium and an intermediate o phase. The following compositions were prepared: Cr-35 and -40Re; Cr-10, -15, -18, -21, -24, and -27 pct Ru; Cr-25 and -30 pct Co; Cr-30, -40, and -50 pct Fe; Cr-45, -55, and -65 pct Mn. Seven other systems were also studied which partially resemble Cr-Re. These systems have extensive chromium solid solutions or a complex intermediate phase, not necessarily o. The compositions evaluated include the following: Cr-20 pct Ti; Cr-15, -30, and -45 pct V; Cr-2.5 pct Cb; Cr-2.5 pct Ta; Cr-20 pct Ni; Cr-6, -9, -12, and -15 pct 0s; Cr-10 pct Ir. The compositions of alloys in these systems were chosen near the solubility limit for the chromium-base solid solutions, since in the Group VI-A Re systems, the saturated alloys are the most ductile. These alloys were evaluated on the basis of hardness, fabricability, and ductile-to-brittle transition temperatures. In addition to the studies of alloying effects on ductility, an exploratory investigation was conducted on mechanical properties at high temperatures in Cr-Ru alloys EXPERIMENTAL PROCEDURE High-purity chromium prepared by the iodide deposition process was employed for all studies. An analysis of this chromium is given in Table I. Alloying elements were obtained in the following forms: Commercially pure powder — iridium, osmium, rhenium, and ruthenium. Arc-melted ingot — titanium and vanadium. Electrolytic flake — iron, manganese, and nickel. Sheet rolled from electron-bearn-melted ingot — columbium and tantalum. Electron-beam-melted ingot — cobalt. Sheet rolled from arc-melted ingot — rhenium. All alloys were initially consolidated by triple arc melting into 60-g button ingots on a water-cooled hearth using a nonconsumable tungsten electrode. The melting atmosphere was Ti-gettered Ar at a pressure of 20 torr. The ingots were drop cast into rectangular slabs and fabricated by heating at 1470" to 2800° F in argon followed by rolling in air. Bend specimens measuring 0.3 by 0.9 in. were cut from the 0.035-in. sheet parallel to the rolling direction. The specimens were annealed for 1 hr in argon, furnace cooled or water quenched, and electropolished prior to testing. Three-point loading bend tests were conducted at a crosshead speed of l-in. per min over

Jan 1, 1969

By Francis H. Brownell

During the 1920&apos;s lead consumption in the United States reached the highest average total ever known. For the ten-year period 1921-&apos;30, it was slightly over 600,000 tons per year, or say 50,000 tons per month, and the price averaged 6.81 per lb. But the I930&apos;s witnessed a severe drop in the consumption of lead is in other business activities. The average U.S. consumption for the ten-year period 1930-&apos;40 was slightly less than 380,000 tons per year, or under 32,000 per month, with the average price dropping to 1.191c. per lb. The outlook in early 1939 was for a continuation of this average consumption and price a demand of 35,000 to 40,000 tons per month, and a price level of 4 1/2 to 5c. in the United States.

Jan 1, 1941

By T. S. Lovering

Geochemical prospecting extends the age-old method of searching out lodes with a gold pan and rationalizes the prospector&apos;s hunch that certain plants are associated with ore. It uses sensitive but cheap and rapid analytical methods to find the diagnostic chemical variations related to hidden mineral deposits. Exploration geologists can gain tremendous assistance from this new tool, although its optimum use is not simple. To bring out the geochemical pattern that reveals the presence of a hidden ore deposit with a minimum number of samples requires a combination of shrewdness, chemical knowledge, and exploration geology. The use of sensitive analytical methods for prospecting had its start in the 1930&apos;s in northern Europe, where Scandinavian and Russian geologists had some success in these early efforts. Very little geochemical prospecting was carried on in the United States at this time, and no sustained interest was manifest until the close of World War II, when geochemical investigations were started by the Mineral Deposits Branch of the U. S. Geological Survey. The purpose of these investigations was to apply geochemical principles and techniques to surface exploration for mineral deposits. Both the research on analytical methods and the routine trace analyses for field investigations were at first conducted by a single group, but it later became apparent that the trace analyses could be done by men of less experience than that required for successful research on methods. For the past several years there have been two groups of chemists, and although their functions overlap, three of the chemists are chiefly concerned with research, while four to six other men make the trace analyses for field projects.

Oct 1, 1955

By A. K. Schellinger, R. D. Lalkaka

IF the ball mill is considered only from an energy standpoint, it can be thought of as a converter of kinetic energy into heat energy and surface energy. The law of the conservation of energy must apply to the ball mill as it does to any machine or process in nature. The heat energy output of the ball mill is apparent to any casual observer of the operating mill since the outflow pulp will be appreciably warmer than the inflow water and rock. The rock in the ball mill is crushed by shearing of its ionic bonding caused by some impact-induced stresses beyond the elastic limit. As the bonds holding the mineral crystal lattices together are ruptured, new surface area is created on each unit of which a definite number of unsaturated bonds exist. Such unsaturated energy of bonding may be termed the "surface energy," and is a potential energy figure. This created energy was withdrawn from the ball mill system and represents an absorption, or disappearance of heat. To reduce the size of the rock, surface area must be created and with it the at- tendant characteristic surface energies of the minerals concerned. Thus the creation of surface energy, from an energy viewpoint, is the creation of useful work by the ball mill. Because of the controversial nature of the energy efficiency figures for modern operating ball mills, it seemed worthwhile to approximate the ordinary magnitude of such efficiencies from the above viewpoint. This was done by an energy balance of the three aforementioned forms of energy, kinetic, heat, and surface energy, for two 9Y2x10-ft grate-type ball mills grinding cement raw materials. Kinetic energy input to the balls was approximated as closely as possible while the heat energy output was measured by means of a thermometer and water and rock flow rates. The assumption was made

Jan 1, 1952